Mikrotik 10/25G NIC supports hw checksum verification on rx for
IP/IPv6 + TCP/UDP packets. HW checksum offload helps reduce host
cpu load.
This enables the csum offload specifically for Mikrotik 10/25G NIC
as other HW supported by the driver is known to have problems with it.
TCP iperf3 to Threadripper 3960X with NIC improved 16.5 -> 20.0 Gbps
with mtu=1500.
Signed-off-by: Gatis Peisenieks <gatis@mikrotik.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new Mikrotik 10/25G NIC supports jumbo frames. Jumbo frames are
supported for TSO as well.
This enables the support for mtu up to 9500 bytes.
Signed-off-by: Gatis Peisenieks <gatis@mikrotik.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel has xmit_more facility that hints the networking driver xmit
path about whether more packets are coming soon. This information can be
used to avoid unnecessary expensive PCIe transaction per tx packet.
Max TX pps on Mikrotik 10/25G NIC in a Threadripper 3960X system
improved from 1150Kpps to 1700Kpps.
Testing L2 forwarding on AR8151 hardware did not reveal a measurable
increase in latency.
Signed-off-by: Gatis Peisenieks <gatis@mikrotik.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new Mikrotik 10/25G NIC maintains compatibility with existing atl1c
driver. However it does have new features.
This defines some new register offsets, code for identifying the new type
of NIC and correct speed detection for the NIC.
Signed-off-by: Gatis Peisenieks <gatis@mikrotik.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The word "acessing" is misspelled, so fix it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some unnecessary parentheses, this patch deletes them.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There should be a blank line after function declaration, so add two
missed blank lines.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two blank lines are unnecessary, this patch removes them.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the alx driver, all locking depended on the RTNL, but
that causes issues with ipconfig ("ip=..." command line)
because that waits for the netdev to have a carrier while
holding the RTNL, but the alx workers etc. require RTNL,
so the carrier won't be set until the RTNL is dropped and
can be acquired by alx workers. This causes long delays
at boot, as reported by Nikolai Zhubr.
Really the only sensible thing to do here is to not use
the RTNL for everything, but instead have fine-grained
locking for just the driver. Do that, it's not that hard.
Reported-by: Nikolai Zhubr <zhubr.2@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some unreachable code, so to suppress this warning:
drivers/net/ethernet/marvell/mvpp2/mvpp2_prs.c: In function ‘mvpp2_prs_tcam_first_free’:
drivers/net/ethernet/marvell/mvpp2/mvpp2_prs.c:397:10: warning: comparison is always false due to limited range of data type [-Wtype-limits]
397 | if (end >= MVPP2_PRS_TCAM_SRAM_SIZE)
| ^~
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp2_run_xdp() has an unused parameter rxq, remove it.
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove MODULE_VERSION(), as it doesn't seem to serve any practical purpose.
For in-tree drivers, the kernel version matters. The code received lots of
changes, but module version remained constant, since the driver landed in
mainline. So, this version doesn't seem have any practical meaning anymore.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse is not happy about handling of strict types in pch_ptp_match():
.../pch_gbe_main.c:158:33: warning: incorrect type in argument 2 (different base types)
.../pch_gbe_main.c:158:33: expected unsigned short [usertype] uid_hi
.../pch_gbe_main.c:158:33: got restricted __be16 [usertype]
.../pch_gbe_main.c:158:45: warning: incorrect type in argument 3 (different base types)
.../pch_gbe_main.c:158:45: expected unsigned int [usertype] uid_lo
.../pch_gbe_main.c:158:45: got restricted __be32 [usertype]
.../pch_gbe_main.c:158:56: warning: incorrect type in argument 4 (different base types)
.../pch_gbe_main.c:158:56: expected unsigned short [usertype] seqid
.../pch_gbe_main.c:158:56: got restricted __be16 [usertype]
Fix that by switching to use proper accessors to BE data.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use readx_poll_timeout_atomic() instead of open coded variants.
While at it, add __iomem attribute to the parameter of pch_gbe_wait_clr_bit().
This in particular will fix a lot of warnings detected by Sparse, e.g.
.../pch_gbe_main.c:308:26: warning: incorrect type in argument 1 (different address spaces)
.../pch_gbe_main.c:308:26: expected void const [noderef] __iomem *
.../pch_gbe_main.c:308:26: got void *reg
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switches the PCH GBE driver to use GPIO descriptors.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
If GPIO controller is not available yet we need to defer
the probe of GBE until provider will become available.
While here, drop GPIOF_EXPORT because it's deprecated and
may not be available.
Fixes: f1a26fdf59 ("pch_gbe: Add MinnowBoard support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statement of the last "if (xxx)" branch is the same as the "else"
branch. Delete it to simplify code.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
device_property_read_u32() may return different error codes.
Propagate it to the caller.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded variants of devm_clk_get_optional().
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the device_get_match_data() helper instead of open coding.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each iteration fwnode_for_each_available_child_node() bumps a reference
counting of a loop variable followed by dropping in on a next iteration,
Since in error case the loop is broken, we have to drop a reference count
by ourselves. Do it for port_fwnode in error case during ->probe().
Fixes: 248122212f ("net: mvpp2: use device_*/fwnode_* APIs instead of of_*")
Cc: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to identify significant signature issues add a new stat counter,
which increases on bad signature values that causes a sync loss.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a new network key would cause a reset of the QCA7000. Usually
the driver only notice the SPI interrupt and a single signature error.
So avoid the whole re-sync process (possible packet loss, transmit queue
stop and no carrier for at least 1 second) in this case.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to read the signature three times. So bail out
in case the second check failed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
and netfilter trees. Self-contained fixes, nothing risky.
Current release - new code bugs:
- dsa: ksz: fix a few bugs found by static-checker in the new driver
- stmmac: fix frame preemption handshake not triggering after
interface restart
Previous releases - regressions:
- make nla_strcmp handle more then one trailing null character
- fix stack OOB reads while fragmenting IPv4 packets in openvswitch
and net/sched
- sctp: do asoc update earlier in sctp_sf_do_dupcook_a
- sctp: delay auto_asconf init until binding the first addr
- stmmac: clear receive all(RA) bit when promiscuous mode is off
- can: mcp251x: fix resume from sleep before interface was brought up
Previous releases - always broken:
- bpf: fix leakage of uninitialized bpf stack under speculation
- bpf: fix masking negation logic upon negative dst register
- netfilter: don't assume that skb_header_pointer() will never fail
- only allow init netns to set default tcp cong to a restricted algo
- xsk: fix xp_aligned_validate_desc() when len == chunk_size to
avoid false positive errors
- ethtool: fix missing NLM_F_MULTI flag when dumping
- can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
- sctp: fix a SCTP_MIB_CURRESTAB leak in sctp_sf_do_dupcook_b
- bridge: fix NULL-deref caused by a races between assigning
rx_handler_data and setting the IFF_BRIDGE_PORT bit
Latecomer:
- seg6: add counters support for SRv6 Behaviors
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmCV3YoACgkQMUZtbf5S
IrsQ2w//Q8/qbl6wGTKUfu6DZHYUU5j5sTwiHR823PKKSgXI+okWMN0KUlZszOsz
qnPkH6GuojRooOE1s8PFLSlt9axKhQ0y7uzMTrWYafQ+JZTtgg9/MiPxQ8fdiE5i
uOG1ngttZ+1jlE5tMPL4GAOSegg3rWVDclzqnJTdsPPOco3MWj6SL9xN0LDPxCEL
BDysRqL/UiOIoh4v6IXQRx2UWjsNGu4biM1po+Jfumnd9T0zKoEpzu6UN6yPShbx
284LihZSQtughCbhGqkErBOxfjZcvpFOQrqmjEvI+Z/eYg4InfWZemt8Sa92/alE
yAFjK76MUTaUxaAO/gk8XauhvkYOzJJwKpqhbOmlaM7oj55QdzT5/8JxMxVoA6hV
pscHOixk15GVse49PdPV8v47cyTLc/Xi69i+/uUdNVVfuORL1wft1w1xbd0S6Pbe
7Gqax21S7zxcDsrUli7cFheYiqtbQAL0anlIUz8tUOZFz0VQ/zPuFd4rUYZ/o38V
Mrevdk3t6CXNxS4CRXyUW4UejYB1O6Qw12sUue31e3h73d6LiN3NAiN5Qp7SEk1/
fvk+jfOf8vvmtimYvcUK2i0D+vqj4Ec/qRIE/XXuUDBcp22tPL9uWMfWavwTdAj1
Se4SzksTWF+NM0lO0ItonMyPh3ZXcSLhIv/gHrZwEKuWkXCGO4M=
=JmWS
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc1, including fixes from bpf, can and
netfilter trees. Self-contained fixes, nothing risky.
Current release - new code bugs:
- dsa: ksz: fix a few bugs found by static-checker in the new driver
- stmmac: fix frame preemption handshake not triggering after
interface restart
Previous releases - regressions:
- make nla_strcmp handle more then one trailing null character
- fix stack OOB reads while fragmenting IPv4 packets in openvswitch
and net/sched
- sctp: do asoc update earlier in sctp_sf_do_dupcook_a
- sctp: delay auto_asconf init until binding the first addr
- stmmac: clear receive all(RA) bit when promiscuous mode is off
- can: mcp251x: fix resume from sleep before interface was brought up
Previous releases - always broken:
- bpf: fix leakage of uninitialized bpf stack under speculation
- bpf: fix masking negation logic upon negative dst register
- netfilter: don't assume that skb_header_pointer() will never fail
- only allow init netns to set default tcp cong to a restricted algo
- xsk: fix xp_aligned_validate_desc() when len == chunk_size to avoid
false positive errors
- ethtool: fix missing NLM_F_MULTI flag when dumping
- can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
- sctp: fix a SCTP_MIB_CURRESTAB leak in sctp_sf_do_dupcook_b
- bridge: fix NULL-deref caused by a races between assigning
rx_handler_data and setting the IFF_BRIDGE_PORT bit
Latecomer:
- seg6: add counters support for SRv6 Behaviors"
* tag 'net-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (73 commits)
atm: firestream: Use fallthrough pseudo-keyword
net: stmmac: Do not enable RX FIFO overflow interrupts
mptcp: fix splat when closing unaccepted socket
i40e: Remove LLDP frame filters
i40e: Fix PHY type identifiers for 2.5G and 5G adapters
i40e: fix the restart auto-negotiation after FEC modified
i40e: Fix use-after-free in i40e_client_subtask()
i40e: fix broken XDP support
netfilter: nftables: avoid potential overflows on 32bit arches
netfilter: nftables: avoid overflows in nft_hash_buckets()
tcp: Specify cmsgbuf is user pointer for receive zerocopy.
mlxsw: spectrum_mr: Update egress RIF list before route's action
net: ipa: fix inter-EE IRQ register definitions
can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
can: mcp251x: fix resume from sleep before interface was brought up
can: mcp251xfd: mcp251xfd_probe(): add missing can_rx_offload_del() in error path
can: mcp251xfd: mcp251xfd_probe(): fix an error pointer dereference in probe
netfilter: nftables: Fix a memleak from userdata error path in new objects
netfilter: remove BUG_ON() after skb_header_pointer()
netfilter: nfnetlink_osf: Fix a missing skb_header_pointer() NULL check
...
Nguyen, Anthony L says:
====================
Intel Wired LAN Driver Updates 2021-05-07
This series contains updates to i40e driver only.
Magnus fixes XDP by adding and correcting checks that were caused by a
previous commit which introduced a new variable but did not account for
it in all paths.
Yunjian Wang adds a return in an error path to prevent reading a freed
pointer.
Jaroslaw forces link reset when changing FEC so that changes take
affect.
Mateusz fixes PHY types for 2.5G and 5G as there is a differentiation on
PHY identifiers based on operation.
Arkadiusz removes filtering of LLDP frames for software DCB as this is
preventing them from being properly transmitted.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Remove LLDP frame filters
i40e: Fix PHY type identifiers for 2.5G and 5G adapters
i40e: fix the restart auto-negotiation after FEC modified
i40e: Fix use-after-free in i40e_client_subtask()
i40e: fix broken XDP support
====================
Link: https://lore.kernel.org/r/20210507164151.2878147-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RX FIFO overflows when the system is not able to process all received
packets and they start accumulating (first in the DMA queue in memory,
then in the FIFO). An interrupt is then raised for each overflowing packet
and handled in stmmac_interrupt(). This is counter-productive, since it
brings the system (or more likely, one CPU core) to its knees to process
the FIFO overflow interrupts.
stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr
into the corresponding hardware register (according to the MAC spec, this
has the effect of restarting the MAC DMA). However, without freeing any rx
descriptors, the DMA stops right away, and another overflow interrupt is
raised as the FIFO overflows again. Since the DMA is already restarted at
the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO
overflow interrupts and the corresponding handling code has no side effect,
and eliminates the interrupt storm when the RX FIFO overflows.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210506143312.20784-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove filters from being setup in case of software DCB and allow the
LLDP frames to be properly transmitted to the wire.
It is not possible to transmit the LLDP frame out of the port, if they
are filtered by control VSI. This prohibits software LLDP agent
properly communicate its DCB capabilities to the neighbors.
Fixes: 4b208eaa80 ("i40e: Add init and default config of software based DCB")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f467 ("i40e: Add support for X710 B/P & SFP+ cards")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196 ("i40e: Add support FEC configuration for Fortville 25G")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the call to i40e_client_del_instance frees the object
pf->cinst, however pf->cinst->lan_info is being accessed after
the free. Fix this by adding the missing return.
Addresses-Coverity: ("Read from pointer after free")
Fixes: 7b0b1a6d0a ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c") broke
XDP support in the i40e driver. That commit was fixing a sparse error
in the code by introducing a new variable xdp_res instead of
overloading this into the skb pointer. The problem is that the code
later uses the skb pointer in if statements and these where not
extended to also test for the new xdp_res variable. Fix this by adding
the correct tests for xdp_res in these places.
The skb pointer was used to store the result of the XDP program by
overloading the results in the error pointer
ERR_PTR(-result). Therefore, the allocation failure test that used to
only test for !skb now need to be extended to also consider !xdp_res.
i40e_cleanup_headers() had a check that based on the skb value being
an error pointer, i.e. a result from the XDP program != XDP_PASS, and
if so start to process a new packet immediately, instead of populating
skb fields and sending the skb to the stack. This check is not needed
anymore, since we have added an explicit test for xdp_res being set
and if so just do continue to pick the next packet from the NIC.
Fixes: 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c")
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The section "19) Editor modelines and other cruft" in
Documentation/process/coding-style.rst clearly says, "Do not include any
of these in source files."
I recently receive a patch to explicitly add a new one.
Let's do treewide cleanups, otherwise some people follow the existing code
and attempt to upstream their favoriate editor setups.
It is even nicer if scripts/checkpatch.pl can check it.
If we like to impose coding style in an editor-independent manner, I think
editorconfig (patch [1]) is a saner solution.
[1] https://lore.kernel.org/lkml/20200703073143.423557-1-danny@kdrag0n.dev/
Link: https://lkml.kernel.org/r/20210324054457.1477489-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org> [auxdisplay]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Each multicast route that is forwarding packets (as opposed to trapping
them) points to a list of egress router interfaces (RIFs) through which
packets are replicated.
A route's action can transition from trap to forward when a RIF is
created for one of the route's egress virtual interfaces (eVIF). When
this happens, the route's action is first updated and only later the
list of egress RIFs is committed to the device.
This results in the route pointing to an invalid list. In case the list
pointer is out of range (due to uninitialized memory), the device will
complain:
mlxsw_spectrum2 0000:06:00.0: EMAD reg access failed (tid=5733bf490000905c,reg_id=300f(pefa),type=write,status=7(bad parameter))
Fix this by first committing the list of egress RIFs to the device and
only later update the route's action.
Note that a fix is not needed in the reverse function (i.e.,
mlxsw_sp_mr_route_evif_unresolve()), as there the route's action is
first updated and only later the RIF is removed from the list.
Cc: stable@vger.kernel.org
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20210506072308.3834303-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas
Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of
a couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał
Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well
as the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of
cleanups and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmCRqDIACgkQqDIjiipP
6E8O2Qf5AQvSVoN9WYRBLo1+a4mkGsJ/wHQMEsOA4FVHft5/QVkRtpMNbSiyq00O
YTpNuoBqiYm/tSTyzK/5Oh+0ucgm/ef4c4dTyPjZYw2GB+3rYNRAXdX/tB6Ggjl/
oUArUCoSQZjOU6Y573B05rcHp1PVM/XL9LgD1uX76tXA1MaGvsyC0cyPRAdOANke
W83BWI0XMhv8B1bZwHVB2Oft5x6HhqWBl3HKbNOmPEMtwkqqBCFAqB0wNEH88ZTf
2hyBjBoZQHdMkJsC0piMvIyAjHZiIjQB47VWz31EvKB3/E28xCqRqPViPq9QbrA5
got0+oDbxI96T024ndXRomc0SSxZnw==
=5THg
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Remove duplicate error message for the amlogic driver (Tang Bin)
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of a
couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well as
the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of cleanups
and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
* tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (55 commits)
thermal/drivers/mtk_thermal: Remove redundant initializations of several variables
thermal/core/power allocator: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Lock the thermal zone while looping over instances
thermal/core/power_allocator: Update once cooling devices when temp is low
thermal/core/power_allocator: Maintain the device statistics from going stale
thermal/core: Create a helper __thermal_cdev_update() without a lock
dt-bindings: thermal: tsens: Document ipq8064 bindings
thermal/drivers/tsens: Add support for ipq8064-tsens
thermal/drivers/tsens: Drop unused define for msm8960
thermal/drivers/tsens: Replace custom 8960 apis with generic apis
thermal/drivers/tsens: Fix bug in sensor enable for msm8960
thermal/drivers/tsens: Use init_common for msm8960
thermal/drivers/tsens: Add VER_0 tsens version
thermal/drivers/tsens: Convert msm8960 to reg_field
thermal/drivers/tsens: Don't hardcode sensor slope
Documentation: driver-api: thermal: Remove thermal_notify_framework from documentation
thermal/core: Remove thermal_notify_framework
iwlwifi: mvm: tt: Replace thermal_notify_framework
dt-bindings: thermal: brcm,ns-thermal: Convert to the json-schema
...
An sk_buff is allocated to send a flow control message, but it's not
sent in all cases: in case the state is not appropiate to send it or if
it can't be enqueued.
In the first of these 2 cases, the sk_buff was discarded but not freed,
producing a memory leak.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling error "eleminate" amended to "eliminate".
Signed-off-by: Sean Gloumeau <sajgloumeau@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In promiscuous mode Receive All bit is set in GMAC packet filter register,
but outside promiscuous mode Receive All bit is not cleared,
which resulted in all network packets are received when toggle (ON/OFF)
the promiscuous mode.
Fixes: e0f9956a38 ("net: stmmac: Add option for VLAN filter fail queue enable")
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In enic_hard_start_xmit, it calls enic_queue_wq_skb(). Inside
enic_queue_wq_skb, if some error happens, the skb will be freed
by dev_kfree_skb(skb). But the freed skb is still used in
skb_tx_timestamp(skb).
My patch makes enic_queue_wq_skb() return error and goto spin_unlock()
incase of error. The solution is provided by Govind.
See https://lkml.org/lkml/2021/4/30/961.
Fixes: fb7516d424 ("enic: add sw timestamp support")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Acked-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is significantly bug fixes and general cleanups. The noteworthy new
features are fairly small:
- XRC support for HNS and improves RQ operations
- Bug fixes and updates for hns, mlx5, bnxt_re, hfi1, i40iw, rxe, siw and
qib
- Quite a few general cleanups on spelling, error handling, static checker
detections, etc
- Increase the number of device ports supported beyond 255. High port
count software switches now exist
- Several bug fixes for rtrs
- mlx5 Device Memory support for host controlled atomics
- Report SRQ tables through to rdma-tool
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEfB7FMLh+8QxL+6i3OG33FX4gmxoFAmCMMHEACgkQOG33FX4g
mxri3Q//RAgIExCGHebQ9xkptZHVyTLLJMpiMl2cqk3ZVRdDZ7QdiQjIqY2KqlUK
nxBj7EXJeX6rV5a1xqCcOO1gBetB28TSwnCNE2ZqrXP5B59ISW8D052IWza3UkUz
WmHLARxHQlyKBWA4+ZAgfoUGL0NmWA8QPf56t/RK/3/OsuYnGzcnWmmFbt8XKFcH
NtO3KC45mKWDqqG0A0XRrLbEQz/ElO3OuPBqlBKgB3ZgGPzgsOUTOGkm1tCcZ89L
/pvZGB7SklKZdCX8TxdpVGd9h0zHl8pqh1yEzvTA1ypNAYSUId2mvZXluU8J5yJl
FLk7E1IxE5050FNEc7T5uZdUVntulYiqL2558coRI34l5w26pKGjIMxw/nTB8hg8
4ZfBtKVemIG6yzW5Up6iBpK7qWYpvLWVShwYAWhbNsjN7JGzJuh1gJnjbmYgyz2P
RTMU9wjFPLL2wZxg4LDHACVJNBb82j6KKuE+kZWpk11ro7INw9+7YwRuTo7/ezxC
BwXKu8wF4igwSigV55jM+WnGXLhxdC3qmx/2cbtWyLM/PzdRL96tM0RWW5v8/Nv7
teFhkt+f3RVqcfYH5K1qCXy3UFrxG6bxFSvcHHSBx2bdIrqhuTY5FqszAYImeW2j
iHoyIsuSuGu79HQgOzAQZsEyksWi6OYDvA9Q9VBoPP4bJ3DOAa4=
=vsXA
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This is significantly bug fixes and general cleanups. The noteworthy
new features are fairly small:
- XRC support for HNS and improves RQ operations
- Bug fixes and updates for hns, mlx5, bnxt_re, hfi1, i40iw, rxe, siw
and qib
- Quite a few general cleanups on spelling, error handling, static
checker detections, etc
- Increase the number of device ports supported beyond 255. High port
count software switches now exist
- Several bug fixes for rtrs
- mlx5 Device Memory support for host controlled atomics
- Report SRQ tables through to rdma-tool"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (145 commits)
IB/qib: Remove redundant assignment to ret
RDMA/nldev: Add copy-on-fork attribute to get sys command
RDMA/bnxt_re: Fix a double free in bnxt_qplib_alloc_res
RDMA/siw: Fix a use after free in siw_alloc_mr
IB/hfi1: Remove redundant variable rcd
RDMA/nldev: Add QP numbers to SRQ information
RDMA/nldev: Return SRQ information
RDMA/restrack: Add support to get resource tracking for SRQ
RDMA/nldev: Return context information
RDMA/core: Add CM to restrack after successful attachment to a device
RDMA/cma: Skip device which doesn't support CM
RDMA/rxe: Fix a bug in rxe_fill_ip_info()
RDMA/mlx5: Expose private query port
RDMA/mlx4: Remove an unused variable
RDMA/mlx5: Fix type assignment for ICM DM
IB/mlx5: Set right RoCE l3 type and roce version while deleting GID
RDMA/i40iw: Fix error unwinding when i40iw_hmc_sd_one fails
RDMA/cxgb4: add missing qpid increment
IB/ipoib: Remove unnecessary struct declaration
RDMA/bnxt_re: Get rid of custom module reference counting
...
In commit f4da56529d ("net: stmmac: Add support for external
trigger timestamping"), struct stmmac_priv was declared at line 507
which caused duplicate struct declarations.
Remove later duplicate declaration here.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove it from the MODULE_AUTHOR statements referencing it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If selftest and reset are performed at the same time, the phy
loopback setting may be still in enable state after the reset,
and device cannot link up. So fix this issue by disabling phy
loopback before phy_start().
Fixes: 256727da73 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW error and global reset are reported through MSIX interrupts.
The same error may be reported to different functions at the
same time. When global reset begins, the pending reset request
set by this error is unnecessary. So clear the pending reset
request after the reset is complete to avoid the repeated reset.
Fixes: f6162d4412 ("net: hns3: add handling of hw errors reported through MSIX")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, netif_tx_stop_all_queues() is used to ensure that
the xmit is not running, but for the concurrent case it will
not take effect, since netif_tx_stop_all_queues() just sets
a flag without locking to indicate that the xmit queue(s)
should not be run.
So use netif_tx_disable() to replace netif_tx_stop_all_queues(),
it takes the xmit queue lock while marking the queue stopped.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb->ip_summed is CHECKSUM_PARTIAL, for non-tunnel udp packet,
which has a dest port as the IANA assigned, the hardware is expected
to do the checksum offload, but the hardware whose version is below
V3 will not do the checksum offload when udp dest port is 4790.
So fixes it by doing the checksum in software for this case.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue found when network interface is down and up again, FPE handshake
fails to trigger. This is due to __FPE_REMOVING bit remains being set in
stmmac_fpe_stop_wq() but not cleared in stmmac_fpe_start_wq(). This
cause FPE workqueue task, stmmac_fpe_lp_task() not able to be executed.
To fix this, add clearing __FPE_REMOVING bit in stmmac_fpe_start_wq().
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass 0 as offset. Therefore remove the parameter and use a
fixed offset 0 in pci_vpd_find_tag().
Link: https://lore.kernel.org/r/f62e6e19-5423-2ead-b2bd-62844b23ef8f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Variable 'err' is set to -EIO but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed.
Clean up the following clang-analyzer warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1195:2: warning: Value
stored to 'err' is never read [clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable queue is set to bp->queues but these values is not used as it
is overwritten later on, hence redundant assignment can be removed.
Cleans up the following clang-analyzer warning:
drivers/net/ethernet/cadence/macb_main.c:4919:21: warning: Value stored
to 'queue' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
drivers/net/ethernet/cadence/macb_main.c:4832:21: warning: Value stored
to 'queue' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, the device is not initialized because reset failed.
If another task calls hns3_reset_notify_up_enet() before reset
retry, it will cause an error since uninitialized pointer access.
So add check for HNS3_NIC_STATE_INITED before calling
hns3_nic_net_open() in hns3_reset_notify_up_enet().
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message sent to VF should be initialized, otherwise random
value of some contents may cause improper processing by the target.
So add a initialization to message in hclge_get_link_mode().
Fixes: 9194d18b05 ("net: hns3: fix the problem that the supported port is empty")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the UM, the type and enable status of igu_egu_hw_err
should be configured separately. Currently, the type field is
incorrect when disable this error. So fix it by configuring these
two fields separately.
Fixes: bf1faf9415 ("net: hns3: Add enable and process hw errors from IGU, EGU and NCSI")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
In case ethernet driver is enabled and INET is disabled, selftest will
fail to build.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 3e1e58d64c ("net: add generic selftest support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210428130947.29649-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to a common ocelot_port_txtstamp_request() for TX timestamp
request handling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..).
If some error happens in emac_tx_fill_tpd(), the skb will be freed via
dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd().
But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len).
As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len,
thus my patch assigns skb->len to 'len' before the possible free and
use 'len' instead of skb->len later.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable ret is set to zero but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed.
Cleans up the following clang-analyzer warning:
drivers/net/ethernet/davicom/dm9000.c:1527:5: warning: Value stored to
'ret' is never read [clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable prev_link and curr_link is being assigned a value from a
calculation however the variable is never read, so this redundant
variable can be removed.
Cleans up the following clang-analyzer warning:
drivers/net/ethernet/amd/pcnet32.c:2857:4: warning: Value stored to
'prev_link' is never read [clang-analyzer-deadcode.DeadStores].
drivers/net/ethernet/amd/pcnet32.c:2856:4: warning: Value stored to
'curr_link' is never read [clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=iidq
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
Core changes:
- Provide IRQF_NO_AUTOEN as a flag for request*_irq() so drivers can be
cleaned up which either use a seperate mechanism to prevent auto-enable
at request time or have a racy mechanism which disables the interrupt
right after request.
- Get rid of the last usage of irq_create_identity_mapping() and remove
the interface.
- An overhaul of tasklet_disable(). Most usage sites of tasklet_disable()
are in task context and usually in cleanup, teardown code pathes.
tasklet_disable() spinwaits for a tasklet which is currently executed.
That's not only a problem for PREEMPT_RT where this can lead to a live
lock when the disabling task preempts the softirq thread. It's also
problematic in context of virtualization when the vCPU which runs the
tasklet is scheduled out and the disabling code has to spin wait until
it's scheduled back in. Though there are a few code pathes which invoke
tasklet_disable() from non-sleepable context. For these a new disable
variant which still spinwaits is provided which allows to switch
tasklet_disable() to a sleep wait mechanism. For the atomic use cases
this does not solve the live lock issue on PREEMPT_RT. That is mitigated
by blocking on the RT specific softirq lock.
- The PREEMPT_RT specific implementation of softirq processing and
local_bh_disable/enable().
On RT enabled kernels soft interrupt processing happens always in task
context and all interrupt handlers, which are not explicitly marked to
be invoked in hard interrupt context are forced into task context as
well. This allows to protect against softirq processing with a per
CPU lock, which in turn allows to make BH disabled regions preemptible.
Most of the softirq handling code is still shared. The RT/non-RT
specific differences are addressed with a set of inline functions which
provide the context specific functionality. The local_bh_disable() /
local_bh_enable() mechanism are obviously seperate.
- The usual set of small improvements and cleanups
Driver changes:
- New drivers for Nuvoton WPCM450 and DT 79rc3243x interrupt controllers
- Extended functionality for MStar, STM32 and SC7280 irq chips
- Enhanced robustness for ARM GICv3/4.1 drivers
- The usual set of cleanups and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=id4G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual updates from the irq departement:
Core changes:
- Provide IRQF_NO_AUTOEN as a flag for request*_irq() so drivers can
be cleaned up which either use a seperate mechanism to prevent
auto-enable at request time or have a racy mechanism which disables
the interrupt right after request.
- Get rid of the last usage of irq_create_identity_mapping() and
remove the interface.
- An overhaul of tasklet_disable().
Most usage sites of tasklet_disable() are in task context and
usually in cleanup, teardown code pathes. tasklet_disable()
spinwaits for a tasklet which is currently executed. That's not
only a problem for PREEMPT_RT where this can lead to a live lock
when the disabling task preempts the softirq thread. It's also
problematic in context of virtualization when the vCPU which runs
the tasklet is scheduled out and the disabling code has to spin
wait until it's scheduled back in.
There are a few code pathes which invoke tasklet_disable() from
non-sleepable context. For these a new disable variant which still
spinwaits is provided which allows to switch tasklet_disable() to a
sleep wait mechanism. For the atomic use cases this does not solve
the live lock issue on PREEMPT_RT. That is mitigated by blocking on
the RT specific softirq lock.
- The PREEMPT_RT specific implementation of softirq processing and
local_bh_disable/enable().
On RT enabled kernels soft interrupt processing happens always in
task context and all interrupt handlers, which are not explicitly
marked to be invoked in hard interrupt context are forced into task
context as well. This allows to protect against softirq processing
with a per CPU lock, which in turn allows to make BH disabled
regions preemptible.
Most of the softirq handling code is still shared. The RT/non-RT
specific differences are addressed with a set of inline functions
which provide the context specific functionality. The
local_bh_disable() / local_bh_enable() mechanism are obviously
seperate.
- The usual set of small improvements and cleanups
Driver changes:
- New drivers for Nuvoton WPCM450 and DT 79rc3243x interrupt
controllers
- Extended functionality for MStar, STM32 and SC7280 irq chips
- Enhanced robustness for ARM GICv3/4.1 drivers
- The usual set of cleanups and improvements all over the place"
* tag 'irq-core-2021-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
irqchip/xilinx: Expose Kconfig option for Zynq/ZynqMP
irqchip/gic-v3: Do not enable irqs when handling spurious interrups
dt-bindings: interrupt-controller: Add IDT 79RC3243x Interrupt Controller
irqchip: Add support for IDT 79rc3243x interrupt controller
irqdomain: Drop references to recusive irqdomain setup
irqdomain: Get rid of irq_create_strict_mappings()
irqchip/jcore-aic: Kill use of irq_create_strict_mappings()
ARM: PXA: Kill use of irq_create_strict_mappings()
irqchip/gic-v4.1: Disable vSGI upon (GIC CPUIF < v4.1) detection
irqchip/tb10x: Use 'fallthrough' to eliminate a warning
genirq: Reduce irqdebug cacheline bouncing
kernel: Initialize cpumask before parsing
irqchip/wpcm450: Drop COMPILE_TEST
irqchip/irq-mst: Support polarity configuration
irqchip: Add driver for WPCM450 interrupt controller
dt-bindings: interrupt-controller: Add nuvoton, wpcm450-aic
dt-bindings: qcom,pdc: Add compatible for sc7280
irqchip/stm32: Add usart instances exti direct event support
irqchip/gic-v3: Fix OF_BAD_ADDR error handling
irqchip/sifive-plic: Mark two global variables __ro_after_init
...
For UDP encapsultions, we only support the offloaded Vxlan port and
Geneve port. All other ports included FOU and GUE are not supported so
we need to turn off TSO and checksum features.
v2: Reverse the check for supported UDP ports to be more straight forward.
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware is capable, set the IFF_SUPP_NOFCS flag to support the
sockets option to transmit packets without FCS. This is mainly used
for testing.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support VF device IDs used by the Hyper-V hypervisor.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PF is no longer enforcing an assigned MAC address on a VF, the
VF needs to call bnxt_approve_mac() to tell the PF what MAC address it is
now using. Otherwise it gets out of sync and the PF won't know what
MAC address the VF wants to use. Ultimately the VF will fail when it
tries to setup the L2 MAC filter for the vnic.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move it before bnxt_update_vf_mac(). In the next patch, we need to call
bnxt_approve_mac() from bnxt_update_mac() under some conditions. This
will avoid forward declaration.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly legal for the stack to query and configure VFs via PF
NDOs while the NIC is administratively down. Remove the unnecessary
check for the PF to be in open state.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware previously only allowed promiscuous mode for VFs associated with
a default VLAN. It is now possible to enable promiscuous mode for a VF
having no VLAN configured provided that it is trusted. In such cases the
VF will see all packets received by the PF, irrespective of destination
MAC or VLAN.
Note, it is necessary to query firmware at the time of bnxt_promisc_ok()
instead of in bnxt_hwrm_func_qcfg() because the trusted status might be
altered by the PF after the VF has been configured. This check must now
also be deferred because the firmware call sleeps.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, the driver will not shutdown the link during
IFDOWN if there are still VFs sharing the port. Newer firmware will
manage the link down decision when the port is shared by VFs, so
we can just call firmware to shutdown the port unconditionally and
let firmware make the final decision.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copy the phy related feature flags from the firmware call
HWRM_PORT_PHY_QCAPS to this new field. We can also remove the flags
field in the bnxt_test_info structure. It's cleaner to have all PHY
related flags in one location, directly copied from the firmware.
To keep the BNXT_PHY_CFG_ABLE() macro logic the same, we need to make
a slight adjustment to check that it is a PF.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware reports link signalling mode for certain speeds. In these
cases, print the signalling modes in kernel log link up messages.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink external port attribute for SF (Sub-Function) port flavour
This adds the support to instantiate Sub-Functions on external hosts
E.g when Eswitch manager is enabled on the ARM SmarNic SoC CPU, users
are now able to spawn new Sub-Functions on the Host server CPU.
Parav Pandit Says:
==================
This series introduces and uses external attribute for the SF port to
indicate that a SF port belongs to an external controller.
This is needed to generate unique phys_port_name when PF and SF numbers
are overlapping between local and external controllers.
For example two controllers 0 and 1, both of these controller have a SF.
having PF number 0, SF number 77. Here, phys_port_name has duplicate
entry which doesn't have controller number in it.
Hence, add controller number optionally when a SF port is for an
external controller. This extension is similar to existing PF and VF
eswitch ports of the external controller.
When a SF is for external controller an example view of external SF
port and config sequence:
On eswitch system:
$ devlink dev eswitch set pci/0033:01:00.0 mode switchdev
$ devlink port show
pci/0033:01:00.0/196607: type eth netdev enP51p1s0f0np0 flavour physical port 0 splittable false
pci/0033:01:00.0/131072: type eth netdev eth0 flavour pcipf controller 1 pfnum 0 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port add pci/0033:01:00.0 flavour pcisf pfnum 0 sfnum 77 controller 1
pci/0033:01:00.0/163840: type eth netdev eth1 flavour pcisf controller 1 pfnum 0 sfnum 77 splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
phys_port_name construction:
$ cat /sys/class/net/eth1/phys_port_name
c1pf0sf77
Patch summary:
First 3 patches prepares the eswitch to handle vports in more generic
way using xarray to lookup vport from its unique vport number.
Patch-1 returns maximum eswitch ports only when eswitch is enabled
Patch-2 prepares eswitch to return eswitch max ports from a struct
Patch-3 uses xarray for vport and representor lookup
Patch-4 considers SF for an additioanl range of SF vports
Patch-5 relies on SF hw table to check SF support
Patch-6 extends SF devlink port attribute for external flag
Patch-7 stores the per controller SF allocation attributes
Patch-8 uses SF function id for filtering events
Patch-9 uses helper for allocation and free
Patch-10 splits hw table into per controller table and generic one
Patch-11 extends sf table for additional range
==================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmCDz80ACgkQSD+KveBX
+j4LmggAwS9otYoo639Kmow/wlMZ6yyLsH02zVMFLEJ2AE4VbL73i4iiQ67ZWygL
yQ8HawPAnythx4RsN/M6/WjSKRpdqTC27C9CpdM78zhXb1vnOrlzba7rYngqmo7N
5fIkGyjsUGHNqq+15SftK7JYbXFTe1b5RdWawXkQoyBlXTTBamyxD7C5NMpoDots
/e88Bs8Zy5nVPZqPchIId8TZEKKuO/heTz8ks6q6s/t1MGj7QP+ddxVMgNg00NR5
OpNTr7YYdpHxpfLSUZgdHaptwwKOx+nou8LdJkIKWPs7SHX6HDggyZJjGBOEWtE7
qG7oSip4olOTM0w9PZrAewLwSYhq7Q==
=oqBr
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-04-21
devlink external port attribute for SF (Sub-Function) port flavour
This adds the support to instantiate Sub-Functions on external hosts
E.g when Eswitch manager is enabled on the ARM SmarNic SoC CPU, users
are now able to spawn new Sub-Functions on the Host server CPU.
Parav Pandit Says:
==================
This series introduces and uses external attribute for the SF port to
indicate that a SF port belongs to an external controller.
This is needed to generate unique phys_port_name when PF and SF numbers
are overlapping between local and external controllers.
For example two controllers 0 and 1, both of these controller have a SF.
having PF number 0, SF number 77. Here, phys_port_name has duplicate
entry which doesn't have controller number in it.
Hence, add controller number optionally when a SF port is for an
external controller. This extension is similar to existing PF and VF
eswitch ports of the external controller.
When a SF is for external controller an example view of external SF
port and config sequence:
On eswitch system:
$ devlink dev eswitch set pci/0033:01:00.0 mode switchdev
$ devlink port show
pci/0033:01:00.0/196607: type eth netdev enP51p1s0f0np0 flavour physical port 0 splittable false
pci/0033:01:00.0/131072: type eth netdev eth0 flavour pcipf controller 1 pfnum 0 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port add pci/0033:01:00.0 flavour pcisf pfnum 0 sfnum 77 controller 1
pci/0033:01:00.0/163840: type eth netdev eth1 flavour pcisf controller 1 pfnum 0 sfnum 77 splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
phys_port_name construction:
$ cat /sys/class/net/eth1/phys_port_name
c1pf0sf77
Patch summary:
First 3 patches prepares the eswitch to handle vports in more generic
way using xarray to lookup vport from its unique vport number.
Patch-1 returns maximum eswitch ports only when eswitch is enabled
Patch-2 prepares eswitch to return eswitch max ports from a struct
Patch-3 uses xarray for vport and representor lookup
Patch-4 considers SF for an additioanl range of SF vports
Patch-5 relies on SF hw table to check SF support
Patch-6 extends SF devlink port attribute for external flag
Patch-7 stores the per controller SF allocation attributes
Patch-8 uses SF function id for filtering events
Patch-9 uses helper for allocation and free
Patch-10 splits hw table into per controller table and generic one
Patch-11 extends sf table for additional range
==================
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds device tree probing to the IXP4xx ethernet
driver.
Add a platform data bool to tell us whether to
register an MDIO bus for the device or not, as well
as the corresponding NPE.
We need to drop the memory region request as part of
this since the OF core will request the memory for the
device.
Cc: Zoltan HERPAI <wigyori@uid0.hu>
Cc: Raylynn Knight <rayknight@me.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was using a really dated way of obtaining the
phy by printing a string and using it with phy_connect().
Switch to using more reasonable modern interfaces.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_rx_pkt(), the RX buffers are expected to complete in order.
If the RX consumer index indicates an out of order buffer completion,
it means we are hitting a hardware bug and the driver will abort all
remaining RX packets and reset the RX ring. The RX consumer index
that we pass to bnxt_discard_rx() is not correct. We should be
passing the current index (tmp_raw_cons) instead of the old index
(raw_cons). This bug can cause us to be at the wrong index when
trying to abort the next RX packet. It can crash like this:
#0 [ffff9bbcdf5c39a8] machine_kexec at ffffffff9b05e007
#1 [ffff9bbcdf5c3a00] __crash_kexec at ffffffff9b111232
#2 [ffff9bbcdf5c3ad0] panic at ffffffff9b07d61e
#3 [ffff9bbcdf5c3b50] oops_end at ffffffff9b030978
#4 [ffff9bbcdf5c3b78] no_context at ffffffff9b06aaf0
#5 [ffff9bbcdf5c3bd8] __bad_area_nosemaphore at ffffffff9b06ae2e
#6 [ffff9bbcdf5c3c28] bad_area_nosemaphore at ffffffff9b06af24
#7 [ffff9bbcdf5c3c38] __do_page_fault at ffffffff9b06b67e
#8 [ffff9bbcdf5c3cb0] do_page_fault at ffffffff9b06bb12
#9 [ffff9bbcdf5c3ce0] page_fault at ffffffff9bc015c5
[exception RIP: bnxt_rx_pkt+237]
RIP: ffffffffc0259cdd RSP: ffff9bbcdf5c3d98 RFLAGS: 00010213
RAX: 000000005dd8097f RBX: ffff9ba4cb11b7e0 RCX: ffffa923cf6e9000
RDX: 0000000000000fff RSI: 0000000000000627 RDI: 0000000000001000
RBP: ffff9bbcdf5c3e60 R8: 0000000000420003 R9: 000000000000020d
R10: ffffa923cf6ec138 R11: ffff9bbcdf5c3e83 R12: ffff9ba4d6f928c0
R13: ffff9ba4cac28080 R14: ffff9ba4cb11b7f0 R15: ffff9ba4d5a30000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
Fixes: a1b0e4e684 ("bnxt_en: Improve RX consumer index validity check.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable result is being assigned a value from a calculation
however the variable is never read, so this redundant variable
can be removed.
Cleans up the following clang-analyzer warning:
drivers/net/ethernet/chelsio/inline_crypto/ch_ktls/chcr_ktls.c:1488:2:
warning: Value stored to 'pos' is never read
[clang-analyzer-deadcode.DeadStores].
drivers/net/ethernet/chelsio/inline_crypto/ch_ktls/chcr_ktls.c:876:3:
warning: Value stored to 'pos' is never read
[clang-analyzer-deadcode.DeadStores].
drivers/net/ethernet/chelsio/inline_crypto/ch_ktls/chcr_ktls.c:36:3:
warning: Value stored to 'start' is never read
[clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extended the SF table to cover additioanl SF id range of external
controller.
A user optionallly provides the external controller number when user
wants to create SF on the external controller.
An example on eswitch system:
$ devlink dev eswitch set pci/0033:01:00.0 mode switchdev
$ devlink port show
pci/0033:01:00.0/196607: type eth netdev enP51p1s0f0np0 flavour physical port 0 splittable false
pci/0033:01:00.0/131072: type eth netdev eth0 flavour pcipf controller 1 pfnum 0 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port add pci/0033:01:00.0 flavour pcisf pfnum 0 sfnum 77 controller 1
pci/0033:01:00.0/163840: type eth netdev eth1 flavour pcisf controller 1 pfnum 0 sfnum 77 external true splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Device has SF ids in two different contiguous ranges. One for the local
controller and second for the external controller's PF.
Each such range has its own maximum number of functions and base id.
To allocate SF from either of the range, prepare code to split into
range specific fields into its own structure.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use helper routines for SF id and SF table allocation and free
so that subsequent patch can reuse it for multiple SF function
id range.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Vhca events on eswitch manager are received for all the functions on the
NIC, including for SFs of external host PF controllers.
While SF device handler is only interested in SF devices events related
to its own PF.
Hence, validate if the function belongs to self or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
SF ids in the device are in two different contiguous ranges. One for
the local controller and second for the external host controller.
Prepare code to handle multiple start function id by storing it in the
table.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Extended SF port attributes to have optional external flag similar to
PCI PF and VF port attributes.
External atttibute is required to generate unique phys_port_name when PF number
and SF number are overlapping between two controllers similar to SR-IOV
VFs.
When a SF is for external controller an example view of external SF
port and config sequence.
On eswitch system:
$ devlink dev eswitch set pci/0033:01:00.0 mode switchdev
$ devlink port show
pci/0033:01:00.0/196607: type eth netdev enP51p1s0f0np0 flavour physical port 0 splittable false
pci/0033:01:00.0/131072: type eth netdev eth0 flavour pcipf controller 1 pfnum 0 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port add pci/0033:01:00.0 flavour pcisf pfnum 0 sfnum 77 controller 1
pci/0033:01:00.0/163840: type eth netdev eth1 flavour pcisf controller 1 pfnum 0 sfnum 77 splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
phys_port_name construction:
$ cat /sys/class/net/eth1/phys_port_name
c1pf0sf77
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Supporting SF allocation is currently checked at two places:
(a) SF devlink port allocator and
(b) SF HW table handler.
Both layers are using HCA CAP to identify it using helper routine
mlx5_sf_supported() and mlx5_sf_max_functions().
Instead, rely on the HW table handler to check if SF is supported
or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Query SF vports count and base id of host PF from the firmware.
Account these ports in the total port calculation whenever it is non
zero.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently vport number to vport and its representor are mapped using an
array and an index.
Vport numbers of different types of functions are not contiguous. Adding
new such discontiguous range using index and number mapping is increasingly
complex and hard to maintain.
Hence, maintain an xarray of vport and rep whose lookup is done based on
the vport number.
Each VF and SF entry is marked with a xarray mark to identify the function
type. Additionally PF and VF needs special handling for legacy inline
mode. They are additionally marked as host function using additional
HOST_FN mark.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Total vports are already stored during eswitch initialization. Instead
of calculating everytime, read directly from eswitch.
Additionally, host PF's SF vport information is available using
QUERY_HCA_CAP command. It is not available through HCA_CAP of the
eswitch manager PF.
Hence, this patch prepares the return total eswitch vport count from the
existing eswitch struct.
This further helps to keep eswitch port counting macros and logic within
eswitch.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5_eswitch_get_total_vports() doesn't honor MLX5_ESWICH Kconfig flag.
When MLX5_ESWITCH is disabled, FS layer continues to initialize eswitch
specific ACL namespaces.
Instead, start honoring MLX5_ESWITCH flag and perform vport specific
initialization only when vport count is non zero.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-04-23
This series contains updates to i40e and iavf drivers.
Aleksandr adds support for VIRTCHNL_VF_CAP_ADV_LINK_SPEED in i40e which
allows for reporting link speed to VF as a value instead of using an
enum; helper functions are created to remove repeated code.
Coiby Xu reduces memory use of i40e when using kdump by reducing Tx, Rx,
and admin queue to minimum values. Current use causes failure of kdump.
Stefan Assmann removes duplicated free calls in iavf.
Haiyue cleans up a loop to return directly when if the value is found
and changes some magic numbers to defines for better maintainability
in iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch to support PTP Sync packet one-step timestamping
described one-step timestamping packet handling logic as below in
commit message:
- Trasmit packet immediately if no other one in transfer, or queue to
skb queue if there is already one in transfer.
The test_and_set_bit_lock() is used here to lock and check state.
- Start a work when complete transfer on hardware, to release the bit
lock and to send one skb in skb queue if has.
There was not problem of the description, but there was a mistake in
implementation. The locking/test_and_set_bit_lock() should be put in
enetc_start_xmit() which may be called by worker, rather than in
enetc_xmit(). Otherwise, the worker calling enetc_start_xmit() after
bit lock released is not able to lock again for transfer.
Fixes: 7294380c52 ("enetc: support PTP Sync packet one-step timestamping")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a tight busy-wait loop without a pause with a standard
readx_poll_timeout_atomic routine with a 5 us poll period.
Tested by booting a MT7621 device to ensure the driver initializes
properly.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves GRO performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: Use MTK_RXD4_FOE_ENTRY instead of GENMASK(13, 0)]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done to communicate total TX and RX work done to NAPI.
Count total RX work up instead of remaining work down for clarity.
Remove unneeded local variables for clarity. Use do {} while instead of
goto for clarity.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid rearming interrupt if napi_complete returns false
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uncached memory access is expensive, and there is no need to access all
descriptor words if we can't process them anyway
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value is only updated by the CPU, so it is cheaper to access from the
ring data structure than from a hardware register.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduces the number of interrupts under load
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: add documentation for new struct fields]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
256 descriptors is not enough for multi-gigabit traffic under load on
MT7622. Bump it to 512 to improve performance.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improves tx performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running short on descriptors, only stop the queue for the netdev that
tx was attempted for. By the time something tries to send on the other
netdev, the ring might have some more room already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usleep_range often ends up sleeping much longer than the 10-20us provided
as a range here. This causes significant latency in mdio bus acceses,
which easily adds multiple seconds to the boot time on MT7621 when polling
DSA slave ports.
Use cond_resched instead of usleep_range, since the MDIO access does not
take much time
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should improve performance, since it can use bulk free
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case build_skb fails, call skb_free_frag on the correct pointer. Also
update the DMA structures with the new mapping before exiting, because
the mapping was successful
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since build_skb accesses the data area (for initializing shinfo), dma unmap
needs to happen before that call
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: split build_skb cleanup fix into a separate commit]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN ID in the rx descriptor is only valid if the RX_DMA_VTAG bit is
set. Fixes frames wrongly marked with VLAN tags.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: fix commit message]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mana_gd_poll_cq() may return -1 if an overflow error is detected (this
should never happen unless there is a bug in the driver or the hardware).
Fix the type of the variable "comp_read" by using int rather than u32.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FDIR entry is found, just return the result directly to break
the loop.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The maximum number (2) of flex-byte support is derived from ethtool
use-def data size (8 byte).
Change the magic number 2 to macro definition, and add the comment to
track the design thinking, so the code is clear and easily maintained.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Both iavf_free_all_tx_resources() and iavf_free_all_rx_resources() have
already been called in the very same function.
Remove the duplicate calls.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The minimum size of admin send/receive queue is 1 and 2 respectively.
The admin send queue can't be set to 1 because in that case, the
firmware would fail to init.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the minimum of the number of descriptors thus we will allocate the
minimal ring buffers for kdump.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Set the number of the MSI-X vectors to 1. When MSI-X is enabled,
it's not allowed to use more TC queue pairs than MSI-X vectors
(pf->num_lan_msix) exist. Thus the number of Tx and Rx pairs
(vsi->num_queue_pairs) will be equal to the number of MSI-X vectors,
i.e., 1.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor repeated link state reporting code into a separate helper
functions: i40e_set_vf_link_state() i40e_vc_link_speed2mbps().
Add support of VIRTCHNL_VF_CAP_ADV_LINK_SPEED;
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
DWMAC Core 5.20 onwards supports HW descriptor prefetching.
Additionally, it also depends on platform specific RTL configuration.
This capability could be enabled by setting DMA_Mode bit-19 (DCHE).
So, to enable this cability, platform must set plat->dma_cfg->dche = true
and the DWMAC core version must be 5.20 onwards. Else, this capability
wouldn`t be configured
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling comm_channel_event in mlx4_master_comm_channel uses a double
loop to determine which slaves have requested work. The search is
always started at lowest slave. This leads to unfairness; lower VFs
tends to be prioritized over higher VFs.
The patch uses find_next_bit to determine which slaves to handle.
Fairness is implemented by always starting at the next to the last
start.
An MPI program has been used to measure improvements. It runs 500
ibv_reg_mr, synchronizes with all other instances and then runs 500
ibv_dereg_mr.
The results running 500 processes, time reported is for running 500
calls:
ibv_reg_mr:
Mod. Org.
mlx4_1 403.356ms 424.674ms
mlx4_2 403.355ms 424.674ms
mlx4_3 403.354ms 424.674ms
mlx4_4 403.355ms 424.674ms
mlx4_5 403.357ms 424.677ms
mlx4_6 403.354ms 424.676ms
mlx4_7 403.357ms 424.675ms
mlx4_8 403.355ms 424.675ms
ibv_dereg_mr:
Mod. Org.
mlx4_1 116.408ms 142.818ms
mlx4_2 116.434ms 142.793ms
mlx4_3 116.488ms 143.247ms
mlx4_4 116.679ms 143.230ms
mlx4_5 112.017ms 107.204ms
mlx4_6 112.032ms 107.516ms
mlx4_7 112.083ms 184.195ms
mlx4_8 115.089ms 190.618ms
Suggested-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that bnxt_show_temp() returns long but "rc" is an int
and "len" is a u32. With ternary operations the type promotion is quite
tricky. The negative "rc" is first promoted to u32 and then to long so
it ends up being a high positive value instead of a a negative as we
intended.
Fix this by removing the ternary.
Fixes: d69753fa1e ("bnxt_en: return proper error codes in bnxt_show_temp")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-04-22
This series contains updates to virtchnl header file, ice, and iavf
drivers.
Vignesh adds support to warn about potentially malicious VFs; those that
are overflowing the mailbox for the ice driver.
Michal adds support for an allowlist/denylist of VF commands based on
supported capabilities for the ice driver.
Brett adds support for iavf UDP segmentation offload by adding the
capability bit to virtchnl, advertising support in the ice driver, and
enabling it in the iavf driver. He also adds a helper function for
getting the VF VSI for ice.
Colin Ian King removes an unneeded pointer assignment.
Qi enables support in the ice driver to support virtchnl requests from
the iavf to configure its own RSS input set. This includes adding new
capability bits, structures, and commands to virtchnl header file.
Haiyue enables configuring RSS flow hash via ethtool to support TCP, UDP
and SCTP protocols in iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few warnings about empty debug macros in this driver:
drivers/net/ethernet/neterion/vxge/vxge-main.c: In function 'vxge_probe':
drivers/net/ethernet/neterion/vxge/vxge-main.c:4480:76: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
4480 | "Failed in enabling SRIOV mode: %d\n", ret);
Change them to proper 'do { } while (0)' expressions to make the
code a little more robust and avoid the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A link time bug that I had fixed before has come back now that
another sub-module was added to the enetc driver:
ERROR: modpost: "enetc_ierb_register_pf" [drivers/net/ethernet/freescale/enetc/fsl-enetc.ko] undefined!
The problem is that the enetc Makefile is not actually used for
the ierb module if that is the only built-in driver in there
and everything else is a loadable module.
Fix it by always entering the directory this time, regardless
of which symbols are configured. This should reliably fix the
problem and prevent it from coming back another time.
Fixes: 112463ddbe ("net: dsa: felix: fix link error")
Fixes: e7d48e5fbf ("net: enetc: add a mini driver for the Integrated Endpoint Register Block")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MANA driver causes a build failure in some configurations when
it selects an unavailable symbol:
WARNING: unmet direct dependencies detected for PCI_HYPERV
Depends on [n]: PCI [=y] && X86_64 [=y] && HYPERV [=n] && PCI_MSI [=y] && PCI_MSI_IRQ_DOMAIN [=y] && SYSFS [=y]
Selected by [y]:
- MICROSOFT_MANA [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROSOFT [=y] && PCI_MSI [=y] && X86_64 [=y]
drivers/pci/controller/pci-hyperv.c: In function 'hv_irq_unmask':
drivers/pci/controller/pci-hyperv.c:1217:9: error: implicit declaration of function 'hv_set_msi_entry_from_desc' [-Werror=implicit-function-declaration]
1217 | hv_set_msi_entry_from_desc(¶ms->int_entry.msi_entry, msi_desc);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
A PCI driver should never depend on a particular host bridge
implementation in the first place, but if we have this dependency
it's better to express it as a 'depends on' rather than 'select'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide the ability to enable SCTP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the SCTP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provides the ability to enable UDP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the UDP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provides the ability to enable TCP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the TCP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the virtchnl message interface to VF, so that VF can request RSS
input set(s) based on PF's capability.
This framework allows ethtool RSS config support on the VF driver.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, RSS hash input is not available to AVF by ethtool, it is set
by the PF directly.
Add the RSS configure support for AVF through new virtchnl message, and
define the capability flag VIRTCHNL_VF_OFFLOAD_ADV_RSS_PF to query this
new RSS offload support.
Signed-off-by: Jia Guo <jia.guo@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Bo Chen <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the driver gets the VF's VSI by using a long string of
dereferences (i.e. vf->pf->vsi[vf->lan_vsi_idx]). If the method to get
the VF's VSI were to change the driver would have to change it in every
location. Fix this by adding the helper ice_get_vf_vsi().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pointer vsi is being re-assigned a value that is never read,
the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add code to support UDP segmentation offload (USO) for
hardware that supports it.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As the hardware is capable of supporting UDP segmentation offload, add a
capability bit to virtchnl.h to communicate this and have the driver
advertise its support.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Declare bitmap of allowed commands on VF. Initialize default
opcodes list that should be always supported. Declare array of
supported opcodes for each caps used in virtchnl code.
Change allowed bitmap by setting or clearing corresponding
bit to allowlist (bit set) or denylist (bit clear).
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The call to clk_disable_unprepare() can happen before priv is
initialized. This means moving clk_disable_unprepare out of
out_release into a new label.
Fixes: 8ef7adc6be ("net: ethernet: ravb: Enable optional refclk")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.
$ sudo ping -f -l 1000 -c 1000 <this driver's ipaddress>
The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO and TBS cannot co-exist and current implementation requires two
fixes:
1) stmmac_open() does not need to call stmmac_enable_tbs() because
the MAC is reset in stmmac_init_dma_engine() anyway.
2) Inside stmmac_hw_setup(), we should call stmmac_enable_tso() for
TX Q that is _not_ configured for TBS.
Fixes: 579a25a854 ("net: stmmac: Initial support for TBS")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO and TBS cannot coexist, for now we set Intel mGbE controller to use
below TX Queue mapping: TxQ0 uses TSO and the rest of TXQs supports TBS.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently added some new locking to this function but one error path
was overlooked. We need to drop the lock before returning.
Fixes: f4da56529d ("net: stmmac: Add support for external trigger timestamping")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of lanes of devlink port should be correctly initialized
when registering the port, so that the input check when running
"devlink port split <port> count <N>" can pass.
Fixes: a21cf0a833 ("devlink: Add a new devlink port lanes attribute and pass to netlink")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a new mailbox to get CPT stats, includes performance
counters, CPT engines status and RXC status.
Signed-off-by: Narayana Prasad Raju Atherya <pathreya@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K CPT coprocessor includes a component named RXC which
is responsible for reassembly of inner IP packets. RXC has
the feature to evict oldest entries based on age/threshold.
This patch adds a new mailbox to configure reassembly age
or threshold.
Signed-off-by: Jerin Jacob Kollanukkaran <jerinj@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds changes to existing CPT mailbox messages to support
CN10K CPT block. This patch also adds new register defines
for CN10K CPT.
Signed-off-by: Vidya Sagar Velumuri <vvelumuri@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result")
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gatis Peisenieks