On our at91sam9260 based board the usart0 and usart1 ports report
their versions (ATMEL_US_VERSION) as 0x10302. This version is not
included in the current checks in the driver.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ef838a81dd ("serial: Add common rs485 device tree parsing
function") consolidated retrieval of rs485 OF properties in a common
helper function but did not #ifdef it to CONFIG_OF. The function is
therefore included on ACPI platforms as well even though it's not used.
On the other hand ACPI platforms with rs485 do exist (e.g. Siemens
IOT2040) and they may leverage _DSD to store rs485 properties. Likewise,
UART platform devices instantiated from an MFD should be able to specify
rs485 properties. In fact, the tty subsystem maintainer had asked for
a "generic" function during review of commit ef838a81dd4d:
https://marc.info/?l=linux-serial&m=150143441725194&w=4
Thus, instead of constraining the helper to OF platforms, make it
platform-agnostic by converting it to device_property_*() functions
and renaming it accordingly.
In imx.c, move the invocation of uart_get_rs485_mode() from
serial_imx_probe_dt() to serial_imx_probe() so that it also gets called
for non-OF devices.
In omap-serial.c, move its invocation further up within
serial_omap_probe_rs485() so that the RTS polarity can be overridden
with the driver-specific "rs485-rts-active-high" property once we
introduce a generic "rs485-rts-active-low" property.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter
As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.
After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Note that there is a small difference between the removed and the now
used implementation: The former cleared flags to 0 if rs485-rts-delay
was given, the common helper clears SER_RS485_RX_DURING_TX and
SER_RS485_ENABLED only but always which makes more sense.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[ukleinek: point out semantic change in commit log]
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that AVR32 is gone, platform_data are not used to initialize the driver
anymore, remove that path from the driver. Also remove the now unused
struct atmel_uart_data.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel_default_console_device was only used by AVR32, in particular
arch/avr32/mach-at32ap/at32ap700x.c which is now gone. Remove it from the
driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A side effect of 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA
from transmitting in stop_tx") is that the console can be called with
TX path disabled. Then the system would hang trying to push charecters
out in atmel_console_putchar().
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 89d8232411 ("tty/serial: atmel_serial: BUG: stop DMA from transmitting
in stop_tx")
Cc: stable <stable@vger.kernel.org> #4.4+
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If uart_flush_buffer() is called between atmel_tx_dma() and
atmel_complete_tx_dma(), the circular buffer has been cleared, but not
atmel_port->tx_len.
That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE -
atmel_port->tx_len) bytes).
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel_serial.h is only used by atmel_serial.c, so there's no need for
it to lie in include/linux.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct cache is only used in suspend/resume. Exclude it when PM is not
selected.
Suggested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The samx7 family uses the same UART/USART IP as the at91/sama5 families but
has 8 of those.
Suggested-by: Szemző András <sza@esh.hu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fractional baud rate generator is available when using the
asynchronous mode of Atmel USART controllers. It makes it possible to
use higher baudrates, in exchange for a less precise clock with a
variable duty cycle.
The existing code restricts its use to the normal mode of the USART
controller, following the recommendation from the datasheet for the
first chip embedding this type of controller. This recommendation has
been removed from the documentation for the newer chips. After
verification, all revisions of this controller should be able to use the
fractional baud rate generator with the different asynchronous modes.
Removing the condition on ATMEL_US_USMODE makes it possible to get
correct baudrates at high speed in more cases.
This was tested with a board using an Atmel SAMA5D2 chip and a TI
WL1831 WiFi/Bluetooth combo chip at 3 Mbauds, with hardware flow control
enabled.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When going to suspend, the UART registers may be lost because the power to
VDDcore is cut. This is not an issue in the normal case but when
no_console_suspend is used, we need to restore the registers in order to
get a functional console.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RS485 in half duplex, RX should be enabled when TX is
finished, and stopped when TX starts.
Before commit 0058f0871e ("tty/serial: atmel: fix RS485 half
duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA
was used. So, collisions could happened.
But disabling RX in atmel_start_tx() uncovered another bug:
RX was enabled again in the wrong place (in atmel_tx_dma) instead of
being enabled when TX is finished (in atmel_complete_tx_dma), so the
transmission simply stopped.
This bug was not triggered before commit 0058f0871e
("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was
never disabled before.
Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem.
Cc: stable@vger.kernel.org
Reported-by: Gil Weber <webergil@gmail.com>
Fixes: 0058f0871e
Tested-by: Gil Weber <webergil@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we don't disable the transmitter in atmel_stop_tx, the DMA buffer
continues to send data until it is emptied.
This cause problems with the flow control (CTS is asserted and data are
still sent).
So, disabling the transmitter in atmel_stop_tx is a sane thing to do.
Tested on at91sam9g35-cm(DMA)
Tested for regressions on sama5d2-xplained(Fifo) and at91sam9g20ek(PDC)
Cc: <stable@vger.kernel.org> (beware, this won't apply before 4.3)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), the hardware handshake wasn't
functional anymore on Atmel platforms (beside SAMA5D2).
To understand why, one has to understand the flag ATMEL_US_USMODE_HWHS
first:
Before commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), this flag was never set.
Thus, the CTS/RTS where only handled by serial_core (and everything
worked just fine).
This commit introduced the use of the ATMEL_US_USMODE_HWHS flag,
enabling it for all boards when the user space enables flow control.
When the ATMEL_US_USMODE_HWHS is set, the Atmel USART controller
handles a part of the flow control job:
- disable the transmitter when the CTS pin gets high.
- drive the RTS pin high when the DMA buffer transfer is completed or
PDC RX buffer full or RX FIFO is beyond threshold. (depending on the
controller version).
NB: This feature is *not* mandatory for the flow control to work.
(Nevertheless, it's very useful if low latencies are needed.)
Now, the specifics of the ATMEL_US_USMODE_HWHS flag:
- For platforms with DMAC and no FIFOs (sam9x25, sam9x35, sama5D3,
sama5D4, sam9g15, sam9g25, sam9g35)* this feature simply doesn't work.
( source: https://lkml.org/lkml/2016/9/7/598 )
Tested it on sam9g35, the RTS pins always stays up, even when RXEN=1
or a new DMA transfer descriptor is set.
=> ATMEL_US_USMODE_HWHS must not be used for those platforms
- For platforms with a PDC (sam926{0,1,3}, sam9g10, sam9g20, sam9g45,
sam9g46)*, there's another kind of problem. Once the flag
ATMEL_US_USMODE_HWHS is set, the RTS pin can't be driven anymore via
RTSEN/RTSDIS in USART Control Register. The RTS pin can only be driven
by enabling/disabling the receiver or setting RCR=RNCR=0 in the PDC
(Receive (Next) Counter Register).
=> Doing this is beyond the scope of this patch and could add other
bugs, so the original (and working) behaviour should be set for those
platforms (meaning ATMEL_US_USMODE_HWHS flag should be unset).
- For platforms with a FIFO (sama5d2)*, the RTS pin is driven according
to the RX FIFO thresholds, and can be also driven by RTSEN/RTSDIS in
USART Control Register. No problem here.
(This was the use case of commit 1cf6e8fc83 ("tty/serial: at91: fix
RTS line management when hardware handshake is enabled"))
NB: If the CTS pin declared as a GPIO in the DTS, (for instance
cts-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_LOW>), the transmitter will be
disabled.
=> ATMEL_US_USMODE_HWHS flag can be set for this platform ONLY IF the
CTS pin is not a GPIO.
So, the only case when ATMEL_US_USMODE_HWHS can be enabled is when
(atmel_use_fifo(port) &&
!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
Tested on all Atmel USART controller flavours:
AT91SAM9G35-CM (DMAC flavour), AT91SAM9G20-EK (PDC flavour),
SAMA5D2xplained (FIFO flavour).
* the list may not be exhaustive
Cc: <stable@vger.kernel.org> #4.4+ (beware, missing atmel_port variable)
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem with previous code was it rounded values in wrong
place and produced wrong baud rate in some cases.
Signed-off-by: Alexey Starikovskiy <aystarik@gmail.com>
[nicolas.ferre@atmel.com: port to newer kernel and add commit log]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 18dfef9c7f ("serial: atmel: convert to irq handling
provided mctrl-gpio"), interrupts from GPIOs are not disabled any more
when the serial port is closed, leading to an oops when the one of the
input pin is toggled (CTS/DSR/DCD/RNG).
This is only the case if those pins are used as GPIOs, i.e. declared
like that:
usart1: serial@f8020000 {
/* CTS and DTS will be handled by GPIO */
status = "okay";
rts-gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
cts-gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
dtr-gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
dsr-gpios = <&pioC 31 GPIO_ACTIVE_LOW>;
rng-gpios = <&pioB 12 GPIO_ACTIVE_LOW>;
dcd-gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
};
That's because modem interrupts used to be freed in atmel_shutdown().
After commit 18dfef9c7f ("serial: atmel: convert to irq handling
provided mctrl-gpio"), this code was just removed.
Calling atmel_disable_ms() disables the interrupts and everything works
fine again.
Tested on at91sam9g35-cm
(This patch doesn't apply on -stable kernels, fixes for 4.4 and 4.7 will
be sent after this one is applied.)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 18dfef9c7f ("serial: atmel: convert to irq handling provided mctrl-gpio")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USART device provides a fractional baud rate generator to get a more
accurate baud rate. It can be used only when the USART is configured in
'normal mode' and this feature is not available on AT91RM9200 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As some race conditions are identified in the termination process of tasklets,
enforce the atmel_shutdown() sequence. This way we make sure that no new
tasklets or software timer are scheduled during shutdown process.
An atomic flag is positioned to give this information throughout the code.
We also remove tasklet_disable() calls that were leading to deadlocks while
stopping the driver. A simpler init/kill sequence is used.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using DMA, half duplex doesn't work properly because rx is not stopped
before starting tx. Ensure we call atmel_stop_rx() in the DMA case.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a macro named ATMEL_SERIAL_RINGSIZE which suggesting that it
corresponds to the real size of the ring buffer. Let warn people that
there is a factor of four since allocation size is
sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split TX and RX paths to not schedule RX tasklet on TX events and vice versa.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ status check and related actions was done in the tasklet without
benefit. So, move it back to the IRQ context to simplify IRQ handling and
having the possibility to split the tasklet in two separated ones for
receive and transmit actions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Cc: stable <stable@vger.kernel.org> # v4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With SAMA5D2, the UART has hw timeout but the offset of the register to
define this value is not the same as the one for USART.
When using the new UART, the value of this register was 0 so we never
get timeout irqs. It involves that when using DMA, we were stuck until
the execution of the dma callback which happens when a buffer is full
(so after receiving 2048 bytes).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c39dfebc77, the modular support
code for atmel_serial was removed, as the driver cannot be built as a
module. Because no use case was proposed, the dynamic driver binding
support was removed as well.
The atmel_serial driver can manage up to 7 serial controllers, which are
multiplexed with other functions. For example, in the Atmel SAMA5D2, the
Flexcom controllers can work as USART, SPI or I2C controllers, and on
all Atmel devices serial lines can be reconfigured as GPIOs.
My use case uses GPIOs to transfer a firmware update using a custom
protocol on the lines used as a serial port during the normal life of
the device. If it is not possible to unbind the atmel_serial driver, the
GPIO lines remain reserved and prevent this case from working.
This patch reinstates the atmel_serial_remove function, and fixes it as
it failed to clear the "clk" field on removal, triggering an oops when
a device was bound again after being unbound.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In all functions other than atmel_serial_probe_fifos,
atmel_serial_probe, and atmel_console_init, the name "port" is used to
refer to an instance of struct uart_port. In many of these functions,
"atmel_port" is used to refer to an instance of struct atmel_uart_port.
We make the use of the name "port" consistent by making
atmel_serial_probe_fifos, atmel_serial_probe, and atmel_console_init
use "atmel_port" to refer to an instance of struct atmel_uart_port
instead of the previous name of "port".
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
[nicolas.ferre@atmel.com: fix typo in variable, adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with sama5d2, the new UART revision has an hardware timer. So, add it
to the IP detection code and set the "has_hw_timer" property for it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional change is associated with this patch.
A driver property depends on the Atmel serial IP revision. This property
is the way the rx timeout is handled: by an hardware or software timer.
So, change this property name and setup code so that it's easier to understand
and more future proof as the distinction of USART vs. UART is blurrier on newer
SoCs.
Variable names and debug comments are also adapted to make this code more obvious.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c39dfebc77 ("drivers/tty/serial:
make serial/atmel_serial.c explicitly non-modular") we removed the code
relating to modular support since it currently only supports built in.
However, when redoing my build coverage for mips allmodconfig, which
sets CONFIG_OF, I noticed a remaining line that needs to be removed,
else we will get a build failure for an undefined module macro.
Unfortunately this didn't appear for any of the other arch I tested
more frequently, such as ARM.
Since MODULE_DEVICE_TABLE is a no-op for non-modular code, we can just
remove the offending line.
Fixes: c39dfebc77 ("drivers/tty/serial: make serial/atmel_serial.c explicitly non-modular")
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Reported-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_ATMEL
drivers/tty/serial/Kconfig: bool "AT91 / AT32 on-chip serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a misplaced bracket in atmel_init_rs485 which sets
rs485-rx-during-tx and rs485-enabled-at-boot-time only if
rs485-rts-delay is set in of.
This is clearly a bug, so fix it by moving the bracket to the proper
place.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turning on KVM and LPAE support on top of a multi_v7_defconfig will
produce a compiler warning in the Atmel serial driver:
drivers/tty/serial/atmel_serial.c: In function 'atmel_verify_port':
drivers/tty/serial/atmel_serial.c:2299:6: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
if ((void *)port->mapbase != ser->iomem_base)
^
Fix that by using the cast on the right hand side instead, as similar
code already does in other drivers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the tty fixes and reverts in here as well so that people can
properly test and use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If atmel_init_gpios fails the port has already been marked as busy (in
line 2629), so this must be undone in the error path.
This bug was introduced because I created the patch that finally
became 722ccf416a ("serial: atmel: fix error handling when
mctrl_gpio_init fails") on top of 3.19 which didn't have commit
6fbb9bdf0f ("tty/serial: at91: fix error handling in
atmel_serial_probe()") yet.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 722ccf416a ("serial: atmel: fix error handling when mctrl_gpio_init fails")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is done before adding more functionality to the init function with
the existing name. As this new functionality conflicts with stuff
drivers are required to implement themselves up to I want to convert
them one by one to make reviewing and reverting more easy in case I
broke something.
Once mctrl_gpio_init is there and all drivers are converted
mctrl_gpio_init_noauto can be removed again.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit also fixes compiler warnings and errors seen when building
on x86_64.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move ATMEL_MAX_UART from platform_data/atmel.h to atmel_serial.c as this is
the only file using it and it is common practise from tty/serial drivers to
define it directly in the driver file.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes I/O accesses on the Receiver Holding Register and on the
Transmitter Holding Register. Indeed AVR32 can only perform 32bit I/O
accesses on registers: using 8bit I/O accesses would read or write garbage
data.
Fixes: commit b5199d4681 ("tty/serial: at91: add support to FIFOs")
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For now this improvement is only used with TX DMA transfers. The data
width must be set properly when configuring the DMA controller. Also
the FIFO configuration must be set to match the DMA transfer data
width:
TXRDYM (Transmitter Ready Mode) and RXRDYM (Receiver Ready Mode) must
be set into the FIFO Mode Register. These values are used by the
USART to trigger the DMA controller. In single data mode they are not
used and should be reset to 0.
So the TXRDYM bits are changed to FOUR_DATA; then USART triggers the
DMA controller when at least 4 data can be written into the TX FIFO
througth the THR. On the other hand the RXRDYM bits are left unchanged
to ONE_DATA.
Atmel eXtended DMA controller allows us to set a different data width
for each part of a scatter-gather transfer. So when calling
dmaengine_slave_config() to configure the TX path, we just need to set
dst_addr_width to the maximum data width. Then DMA writes into THR are
split into up to two parts. The first part carries the first data to
be sent and has a length equal to the greatest multiple of 4 (bytes)
lower than or equal to the total length of the TX DMA transfer. The
second part carries the trailing data (up to 3 bytes). The first part
is written by the DMA into THR using 32 bit accesses, whereas 8bit
accesses are used for the second part.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonas Danielsson