This patch tidies up a few loose ends left by the preceding patches.
It indicates the controller supports remote wakeup whenever the PM
capability is present -- which shouldn't cause any harm if the
assumption turns out to be wrong. It refuses to suspend the
controller if the root hub is still active, and it refuses to resume
the root hub if the controller is suspended. It adds checks for a
dead controller in several spots, and it adds memory barriers as
needed to insure that I/O operations are completed before moving on.
Actually I'm not certain the last part is being done correctly. With
code like this:
outw(..., ...);
mb();
udelay(5);
do we know for certain that the outw() will complete _before_ the
delay begins? If not, how should this be written?
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements (finally!) separate suspend and resume routines
for the root hub and the controller in the UHCI driver. It also
changes the sequence used to reset the controller during initial
probing, so as to preserve the existing state during a Resume-From-Disk.
(This new sequence is what should be used in the PCI Quirks code for
early USB handoffs, incidentally.) Lastly it adds a notion of the
controller being "inaccessible" while in a PCI low-power state, when
normal I/O operations shouldn't be allowed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch starts making some serious changes to the UHCI driver.
There's a set of private states for the root hub, and the internal
routines for suspending and resuming work completely differently, with
transitions based on the new states. Now the driver distinguishes
between a privately auto-stopped state and a publicly suspended state,
and it will properly suspend controllers with broken resume-detect
interrupts instead of resetting them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes a few small improvements in the UHCI driver. Some
code is moved between different source files and a more useful pointer
is passed to a callback routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves a few subroutines around in the uhci-hcd source file.
Nothing else is changed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch turns a user mode driver error into a hard error, and updates
the relevant diagnostic slightly to help troubleshooting. gphoto was
known to have this problem, hopefully it is now fixed (they have had
plenty of warning...)
This had been left as a soft error to give various user mode drivers a
change to be properly fixed, with the statement that starting in about
2.6.10 it would be changed. It had been mostly safe as a soft error ...
but that can not be guaranteed. Now that a year has passed, it's time to
really insist that the user mode drivers finally fix their relevant bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an oops triggered at rmmod of isp116x-hcd
after the probe() has failed.
Also, it extends the error message printed, if the driver
cannot detect "Chip's Clock Ready" after a software reset.
As Ian Campbell recently reported, this happens if the
chip's H_WAKEUP pin is not pulled low during software reset.
Several people have already had this issue, hence the update
to the error message.
Also, extend the error message about the failed clock
detection after the software reset.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.
The driver:
- is relatively small, meant for use on embedded platforms.
- runs usbtests 1-14 without problems for days.
- has been in use by 6-7 different people on ARM and PPC platforms,
running a range of devices including USB hubs.
- supports suspend/resume of both the platform device and the root hub;
supports remote wakeup of the root hub (but NOT the platform device)
by USB devices.
- does NOT support ISO transfers (nobody has asked for them).
- is PIO-only.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various USB patches, mostly for portability:
- Fifo mode 1 didn't work previously (oopsed), so now it's fixed and
(why not) defines even more endpoints for composite devices.
- OMAP 1710 doesn't have an internal transceiver.
- Small PM update: if the USB link is suspended, don't disconnect on
entry to deep sleep.
- Be more correct about handling zero length control reads. OMAP
seems to mis-handle that protocol peculiarity though; best avoided.
- Platform device resources (for UDC and OTG controllers) now use
physical addresses, so /proc/iomem is more consistent.
- Minor cleanups, notably (by volume) for "sparse" NULL warnings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch changes the g_file_storage driver to make the "stall" module
parameter generally available; currently it is available only if the
testing version of the module has been configured. It also fixes a typo
in a comment -- thanks, Pat!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch simplifies the g_file_storage driver by consolidating a bunch
of min() calculations at a single spot.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB ethernet drivers did not accept multicast frames appropriately.
IPv6 did not work with those drivers without this patch.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/media/pwc/pwc-uncompress.c: In function `pwc_decompress':
drivers/usb/media/pwc/pwc-uncompress.c:140: warning: unreachable code at beginning of switch statement
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various filesystem drivers have grown a get_dentry() function that's a
duplicate of lookup_one_len, except that it doesn't take a maximum length
argument and doesn't check for \0 or / in the passed in filename.
Switch all these places to use lookup_one_len.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers need to return -ENODEV when they can't bind to a device.
Anything else stops the "bind a device to a driver" search.
From: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes usb_driver_release_interface() to make it avoid calling
device_release_driver() recursively, i.e., when invoked from within the
disconnect routine for the same device. The patch applies to your
"driver" tree.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code looks like this:
/* if interface was already added, bind now; else let
* the future device_add() bind it, bypassing probe()
*/
if (!list_empty (&dev->bus_list))
device_bind_driver(dev);
IOW, it's checking to see if the device is attached to the bus or not
and binding the driver if it is. It's checking the device's bus list,
which will only appear empty when the device has been initialized, but
not added. It depends way too much on the driver model internals, but it
seems to be the only way to do the weird crap they want to do with
interfaces.
When I converted it to use klists, I accidentally inverted the logic,
which led to bad things happening. This patch returns the check to its
orginal value.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/usb.c
===================================================================
Trivial fix to USB class-creation error path; please apply.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core:
change driver's, bus's, class's and platform device's names
to be const char * so one can use
const char *drv_name = "asdfg";
when initializing structures.
Also kill couple of whitespaces.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the EHCI driver spin a bit longer before concluding that the
port reset failed. "Obviously safe."
It allows some devices to enumerate that previously didn't. We've seen
a bunch of these problem reports recently, this will make some go away.
As reported by Michael Zapf <Michael.Zapf@uni-kassel.de>, some EHCI
controllers seem to take forever to finish port resets and produce
"port N reset error -110" type errors. Spinning a bit longer helps.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pwc chainsaw session left some setups not working. There is a
sanity check on compression buffers that simply isn't right any more as
we never allocate one.
This doesn't address the email and other changes. I'll do those
tomorrow if I get time, but it is the minimal fix for the code and basic
feature set.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Avoid losing bytes at tty-ldisc.
This patch was originally developed by Daniel Smertnig. I
(Ian Abbott) made a few changes. It has been tested by both
Daniel and I, at least for raw, non-canonical receive data
processing.
Here is Daniel's original description of the patch:
===
During a project in which I was using a FTDI 232BM to
transmit data at relative high speeds (625kBit/s), I
noticed a problem where data was lost even if flow
control was enabled: The FTDI-Driver receives 512 Bytes
of data over USB at a time, which consists of 8 64-Byte
packets. Subtracting the 2 bytes of status information
included in each packet this gives 496 "real" data
bytes per read.
This data is passed (indirectly, via the flip buffers)
to the tty line discipline which takes care of
throttling when there the free buffer space reaches
TTY_THRESHOLD_THROTTLE (128). Because the FTDI driver
processes up to 496 bytes at a time, throttling won't
happen in time and the line discipline will discard the
remaining bytes.
To avoid this the patch passes data in 62-byte blocks
to the tty layer and checks the available space in the
ldisc-buffers. If there isn't enough free space,
processing the rest of the data is delayed using a
workqueue.
Note: The original problem should be easily
reproducible with a userspace program which does slow &
small reads.
===
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Daniel Smertnig <daniel.smertnig@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This "obvious" one-liner is needed to recognize Zaurus SL 6000;
it just checks two GUIDs not just one.
OSDL bugids #4512 and #4545 seem to be duplicates of this report.
From: Gerald Skerbitz <gsker@tcfreenet.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added support to get/set flow control line levels using TIOCMGET and
TIOCMSET.
Added support for RTSCTS hardware flow control.
cp2101_get_config and cp2101_set_config modified to support long request
strings, required for configuring flow control.
Signed-off-by: Craig Shelley craig@microtron.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original entry of this patch was submitted by Filippo Bardelli
<filibard@libero.it>, with cleanups and patch-ification by me.
This corrects the subclass that the device reports.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the code to provide modalias in sysfs for usb devices
56 bytes smaller in i386, while making it clear that the first part of
the modalias string is the same no matter what the device class is.
Signed-Off-By: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new driver for "Option" cards. This is a GSM data card,
controlled by three "serial ports" which are connected via an OHCI adapter,
all located on an oversized PC-Card. It's sold by several GSM service
providers.
Traditionally, this card has been accessed via the standard serial driver
and appropriate vendor= and product= options. However, testing has
revealed several problems with this approach, including hung data transfers
and lost data blocks when receiving.
Therefore, I've written a separate driver.
Signed-off-by: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They aren't really HID devices.
Damm microsoft HID driver, that thing has caused more companies to have
to do this kind of hack...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the DeLorme Earthmate lt-20 productid to the hid
blacklist table. This patch ensures the lt-20 can be claimed by the
appropriate driver (cypress_m8).
Adds the product id 0x200, of the DeLorme Earthmate lt-20, to the hid
blacklist table.
Signed-off-by: Lonnie Mendez <lmendez19@austin.rr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the outdated ChangeLog file for this driver.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At module load time, if a generic device is found, the tty information
for the device is not set up properly (as the tty structures aren't initialized
yet.) This can cause big problems for things like udev. This patch fixes this.
Thanks to Kay Sievers for the original patch for this problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Add PID for "ELV USB Module UM100".
PID sent by Armin Laugher.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for a CF-card USB Host adapter, the Ratoc REX-CFU1U, by
wrapping a PCMCIA driver around the existing "sl811-hcd" platform driver.
This CF card is especially useful for PDAs, which currently tend to have
no other solution for USB host capability.
From: Botond Botyanszki <boti@rocketmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various fixes to the sl811-hcd driver:
* Fix small glitches that crept in during recent evolution of usbcore's hcd
glue layer, coupling endpoint state records to usbcore and active urbs.
(As noted by folk whose boards weren't stuck on 2.6.9 kernels...)
* Cope with various system-specific issues:
- Some configurations (e.g. a CF-card uses this chip) have iospace
addresses for the two registers, rather than memory mapped ones.
- Some configurations do interesting things with IRQs; maybe the
line is shared, or it doesn't support level triggering.
- Not all boards can drive the chip reset line in software.
* Address a potential race during unlinking.
* Tweak probe/remove section info to handle the case where this segment
of a platform bus is hotpluggable (e.g. CF card). (The basic problem
is that CONFIG_HOTPLUG is global, which is wrong since not all busses
can hotplug even on hotplug-friendly systems...) Also export the
driver, so that the CF driver can depend on it.
Also removed some annoying end-of-line whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
due to a masking bug in hid-core.c:extract(). This patch fixes it
up by forcing the mask to be 64 bits wide.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Windows does. This should make life easier for devices that were
tested with Windows only.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The neutering of the pwc driver was incomplete. It still references
some now-dead files..
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In netdev-2.6 we need to update zd1201.c since we don't have
driver/net/wireless/ieee802_11.h anymore.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
The original pwc author raised some questions about the reverse
engineering of the decompressor algorithms used in the pwc driver.
Having done some detailed investigation it appears those concerns that
clean room policy was not followed are reasonable. I've also had a
friendly discussion with Philips to ask their view on this.
This removes the problem items of code which reduces the pwc
functionality in the kernel a little but leaves all the framework for
setup that will be needed for decompressors in user space (where they
eventually belong). This change set is designed to be the minimal risk
change set given that 2.6.12 is hopefully close to hand, with a view to
merging the much updated pwc code in 2.6.13 series kernels.
Someone else can then redo the decompressors properly (clean room) in
user space.
Note that while its easy to say that it should have been caught earlier,
but the violation was really only obvious to someone who had access to
both the proprietary source and the 'GPL' source.
There's a bigger Speedtouch update coming your way after 2.6.12 but in
the meantime, let's at least make it automatically resync if the DSL
signal is lost.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the DeLorme Earthmate lt-20 to the
cypress_m8 driver. The device was tested and found to be compatible
with the cypress_m8 driver. This is a resend with the complete patch
which properly compiles.
Adds support for the DeLorme Earthmate lt-20 to the cypress_m8 driver.
Signed-off-by: Lonnie Mendez <lmendez19@austin.rr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Force the EHCI watchdog timer off during suspend, in case for some
reason it was still running after the root hub suspended.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updates to the usbnet driver:
- Remove a warning when built with Zaurus support but not CDC Ethernet;
just moves an #ifdef to cover more code
- Two tweaks to the pseudo-MDLM support:
* correctly handle _either_ of the two GUIDs
* ignore a padding bit that doesn't seem necessary
- Remove ID for one Motorola phone that uses the MDLM stuff.
It also updates the Kconfig helptext to make it clearer that the "Zaurus"
configuration option supports an increasing (sigh) family of nonstandard
peripheral protocols.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed problem where setting or retreiving the serial config would fail
with EPIPE. Removed CRTS toggling so the driver behaves more like other
usbserial adapters. Issued new interval of 1ms instead of the default
bInterval. As a result, transfer speed has been substantially
increased. From avg. 850bps to avg. 3300bps. Also added new module
parameter 'interval' to tweak the interval in case this change causes
problems for someone. Cleaned up code and formatting issues so source
is more readable. Replaced the C++ style comments. Various other code
cleanups.
Signed-off-by: Lonnie Mendez <lmendez19@austin.rr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for the Minolta Dimage Z10.
Originally reported by Vilisas <vilisas@xxx.lt>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ftdi_sio] Replaced redundant INTERFACE_A and INTERFACE_B macros with
the equivalent PIT_SIOA and PIT_SIOB macros.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some VID/PID updates for the ftdi_sio driver:
* The "Gude Analog- und Digitalsysteme GmbH" entries were missing from
the "combined" table.
* Replaced FTDI_8U232AM_ALT_ALT_PID with 3 PIDs for devices from
4n-galaxy.de.
* Removed redundant FTDI_RM_VID and renamed FTDI_RMCANVIEW_PID to
FTDI_RM_CANVIEW_PID.
* Added VID/PID for serial converter in Mobility Electronics EasiDock
USB 200 (mentioned by Gregory Schmitt).
* Added PID for Active Robots USB comms board (mentioned by John Koch).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -ur a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
On Thu, Apr 14, 2005 at 11:06:21PM +0400, Sergey Vlasov wrote:
> http://thread.gmane.org/gmane.linux.usb.devel/32977
>
> (see "[PATCH] N/3 cdc acm errors").
>
> You also need this driver core fix:
>
> http://thread.gmane.org/gmane.linux.usb.devel/33132
I reproduced the same oops while trying to execute at+mode=99, it would
be nice to get these fix merged since I believe it's still needed to
connect the laptop over gprs (something I didn't test yet).
This further patch will allow you to connect via usbnet, Greg could you
apply? Thanks!
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Miscellaneous updates for EHCI.
- Mostly updates the power switching on EHCI controllers. One routine
centralizes the "power on/off all ports" logic, and the capability to
do that is reported more correctly.
- Courtesy Colin Leroy, a patch to always power up ports after resumes
which didn't keep a USB device suspended. The reset-everything logic
powers down those ports (on some hardware) so something needs to turn
them back on.
- Minor tweaks/bugfixes for the debug port support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a compiler error caused by a missing prototype. It should
apply directly to Greg KH's usb-2.6.git tree.
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when stealing code from ati_remote for a GPL-driver of my usbradio (because of
its neat usb int transfers) I found out, that the inbuf is freed twice.
I don't have the ati-remote, so I don't know it is a problem at all, but it
looks strange to me anyway. Also I don't know if it has been fixed already in
newer kernel versions.
From: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a somewhat more comprehensive fix for the problem of devices
like the newer Zaurii ... or in this case some Motorola cell phones.
To recap, the problem's root cause is that these devices aren't using
standard USB class specifications for their network links, and so far
we've had to add lots of device-specific driver entries. The vendor
fix abuses the CDC MDLM descriptors (they _could_ have conformed to
the spec, but didn't) and defines a "Belcarra firmware" pseudo-class.
This patch recognizes that pseudo-class by the GUIDs in those descriptors,
and handles the devices that just use the Zaurus framing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the ASIX USB Ethernet code to make use of the new status
infrastructure in usbnet.
Additionally, add a link_reset() handler to the struct usbnet
structure to provide a generic means for a driver to perform link
reset tasks such as a determining link speed and setting
device flags accordingly.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below adjusts the MODALIAS generated by the usb hotplug
function to match the proposed change to scripts/mod/file2alias.c.
Signed-off-by: Roman Kagan <rkagan@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Dibowitz wrote:
> 1. You're adding product IDs 1202, 1203, 1204, and 1205. 1203 was
> already there, but you remove it, OK, but 1205 is already there, so
> you'll need to fix that.
I was not removing 1203, it's just the extension of the bcd range. You are
right about 1205, as I wrote, it was a patch against 2.6.11.7. Attached is
a patch against 2.6.12-rc2.
> 2. I'm OK with the full bcd range if Apple is changing it on firmware
> revs... fine, but it's bcd, not hex... 0x9999 =)
I just copied from other entries. There're a lot 0xffffs in unusual_dev.h,
so I assumed it is correct. I changed it to 0x9999.
> 3. It's rather obnoxious to take the original submitter's credit away.
I didn't remove it, I changed it to "based on...". Because I changed
something (the range) in his entry, I thought it is the best to take the
responsibility but keep the origin. Anyway, in the new patch I did it in a
different way.
> 4. Your /proc/bus/usb/devices shows 1204, but I see no evidence 1202 is
> really an iPod.
I don't have an old iPod mini, but you find a lot of evidence here:
http://www.google.com/search?q=0x1202+ipod
Especially this one:
http://www.qbik.ch/usb/devices/showdescr.php?id=2737
> It also looks like 1205's entry is getting mangled, but I haven't
> attempted to apply the patch, so I'm not sure.
No, the patch was ok, but I agree it looks strange. It's not very
readable, because I cannot tell diff to work blockwise instead of
linewise. Because of the similarity of the entries, diff splits and merges
them. Anyway, the new patch "looks" better. ;-)
Signed-off-by: Sven Anderson <sven-linux@anderson.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore.
We need to do it ourselves now.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updates to the Ethernet/RNDIS gadget driver (mostly for RNDIS):
- Fix brown-paper bag goof with RNDIS packet TX ... the wrong length
field got set, so Windows would ignore data packets it received.
- More consistent handling of CDC output filters (but not yet hooking
things up so RNDIS uses the mechanism).
- Zerocopy RX for RNDIS packets too (saving CPU cycles).
- Use the pre-allocated interrupt/status request and buffer, rather
than allocating and freeing one of each every few seconds (which
could fail).
- Some more "sparse" tweaks, making both dual-speed and single-speed
configurations happier.
- RNDIS speeds are reported in units of 100bps, not bps.
Plus two minor cleanups (whitespace, messaging).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of a bunch of redundant NULL pointer checks in drivers/usb/*,
there's no need to check a pointer for NULL before calling kfree() on it.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/class/audio.c
===================================================================
Checking for NULL before calling kfree() is redundant. This patch removes
these redundant checks and also makes a few tiny whitespace changes.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please accept the attached patch which adds the vendorid 0x0745 and
modelid 0x0001 (ID 0745:0001) "Syntech Information Co., Ltd."
The device is an USB IR cradle for a barcode scanner (CPT-8001C) from
Cipherlab.
From: Peter Favrholdt <pfavr@mip.sdu.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -u kernel-source-2.6.11/drivers/usb/serial/pl2303.c ../kernel-source-2.6.11/drivers/usb/serial/pl2303.c
I'm attaching a patch to fix status when using Siemens X65
mobile. This mobile use first byte instead of normal UART_STATE
byte.
From: Flavio Leitner <fbl@conectiva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/serial/pl2303.c
===================================================================
It's possible to unplug usb device and do tiocmset() and tiocmget() without
valid interface in pl2303 module.
The patch below check this and return -ENODEV if interface was removed.
From: Flavio Leitner <fbl@conectiva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -purN linux-05-04-11/drivers/usb/serial/pl2303.c linux-05-04-11.usb/drivers/usb/serial/pl2303.c
In response to complaints about excessive latency in the uhci-hcd driver
I'm planning to convert it to a top-half/bottom-half design. It turns out
that to do this, the USB API has to be modified slightly since the driver
will not be able to meet one of the guarantees in the current API. This
patch changes some kerneldoc, specifying the weaker guarantee.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a quirk to the OHCI driver that lets it work with an old
Compaq implementation. It also removes some needless strings from
the non-debug version of the driver.
Signed-off-by: Chris Clayton <chris_clayton@f1internet.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hmm, another case of a Zaurus ROM not telling the expected conformance lie;
this patch handles the lies told by the SL5600.
From: bender647@gmail.com
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the attached patch adds another USB device ID to the list. Seems the
device is known under multiple IDs.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the delay for the US_FL_GO_SLOW patch from 110us to 125.
Some delays need this extra delay includign Jan De Luyck's drive which spawned
the original increase from 110 to 110us. 125 is a microframe, so this delay
seems to make sense more than just be a random delay (thanks to David Brownell
for pointing that out after my original patch).
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/storage/transport.c
===================================================================
On ppc64:
drivers/usb/net/usbnet.c: In function `skb_return':
drivers/usb/net/usbnet.c:429: warning: int format, different type arg (arg 3)
drivers/usb/net/usbnet.c:429: warning: int format, different type arg (arg 3)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -puN drivers/usb/net/usbnet.c~usbnet-printk-warning-fix drivers/usb/net/usbnet.c
I am sorry that the last patch about 32 bit compat ioctl on
64 bit kernel actually breaks the usbdevfs. That is on the current
BK tree. I am retarded.
Here is the patch to fix it. Tested with USB hard disk and webcam
in both 32bit compatible mode and native 64bit mode.
Again, sorry about that.
From: Christopher Li <chrisl@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts a recent change to usb_set_interface(). The change worked
around a quirk in certain devices, but doing this in usbcore creates
needless regressions for other devices. More appropriate fixes won't
put such handling in usbcore.
Basically it's tricky to do a full software reset of USB device state, since
the devices don't all act the same. This adds a note to the kerneldoc for
the usb_reset_configuration() call to highlight the quirk this was working
around: endpoint data toggles not being reset.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
First patch incorrectly changed state of the wait-queue usage to
TASK_UNINTERRUPTIBLE. Reverted to TASK_INTERRUPTIBLE.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch includes minor "sparse -Wbitwise" updates for the PCI based
HCDs. Almost all of them involve just changing the second parameter of the
suspend() method to a pm_message_t ... the others relate to how the EHCI
code walks in-memory data structures. (There's a minor bug fixed there too
... affecting the big-endian sysfs async schedule dump.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/hcd.h
===================================================================
This is the first of a few installments of PM API updates to match the
recent switch to "pm_message_t". This installment primarily affects
USB device drivers (for USB interfaces), and it changes the handful of
drivers which currently implement suspend methods:
- <linux/usb.h> and usbcore, signature change
- Some drivers only changed the signature, net effect this just
shuts up "sparse -Wbitwise":
* hid-core
* stir4200
- Two network drivers did that, and also grew slightly more
featureful suspend code ... they now properly shut down
their activities. (As should stir4200...)
* pegasus
* usbnet
Note that the Wake-On-Lan (WOL) support in pegasus doesn't yet work; looks
to me like it's missing a request to turn it on, vs just configuring it.
The ASIX code in usbnet also has WOL hooks that are ready to use; untested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/net/irda/stir4200.c
===================================================================
This has a variety of updates to the shared suspend/resume code for
PCI based USB host controllers.
- Cope with pm_message_t replacing the target system state.
This is actually a loss of functionality; PCI D1 and D2
states will no longer be used, and it's no longer knowable
that D3cold is on the way so power will be lost.
- Most importantly, some of the resume paths are reworked and
cleaned up. They're now an exact mirror of suspend paths,
and more care is taken to ensure the hardware is reactivated
before the hardware re-enables interrupts.
Plus comment and diagnostic cleanups; there are some nasty cases here
especially combined with swsusp, now they're somewhat commented.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -puN drivers/usb/core/hcd-pci.c~usb-resume-fixes drivers/usb/core/hcd-pci.c
Here's a tiny patch to add support for the Tapwave Zodiac (for
2.6.11.6). I've been meaning to send it in for a while but kept
upgrading my kernel and losing the changes :-) I own the device and it
works fine with the latest pilot-link beta.
From: Larry Battraw <lbattraw@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Jamieson Becker <jamie@jamiebecker.com> for the info
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -Naur -X dontdiff-osdl tmp/linux-2.6.12-rc2/drivers/usb/serial/visor.h linux-2.6/drivers/usb/serial/visor.h
Fix up two drivers that incorrectly were using the old return values for
their new-style EH methods and kill off scsi_obsolete.h that defined the
constants. The initio driver has all these constansts defined locally
and uses them internally, I'll fix that up some time later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix up two drivers that incorrectly were using the old return values for
their new-style EH methods and kill off scsi_obsolete.h that defined the
constants. The initio driver has all these constansts defined locally
and uses them internally, I'll fix that up some time later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Alan Stern