Considering shutdown of the card, the responsibility to initate this
sequence shall be driven from the mmc_bus.
This patch enables the mmc_bus to handle this sequence properly. A new
.shutdown callback is added in the mmc_driver struct which is used to
shutdown the blk device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The host should be responsible to suspend|resume the host and not the
card. This patch changes this behaviour, by moving the responsiblity
to the mmc bus instead which already holds the card device.
The exported functions mmc_suspend|resume_host are now to be considered
as depcrecated. Once all host drivers moves away from using them, we
can remove them. As of now, a successful error code is always returned.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
By moving code from the mmc_suspend|resume_host down into each
.suspend|resume bus_ops callback, we get a more flexible solution.
Some nice side effects are that we get a better understanding of each
bus_ops suspend|resume sequence and the common code don't have to take
care of specific corner cases, especially for the SDIO case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch moves the validation for all the suspend prerequisites to be
done at SUSPEND_PREPARE notification. Previously in the SDIO case parts
of the validation was done from mmc_suspend_host.
This patch invents a new pre_suspend bus_ops callback and implements it
for SDIO. Returning an error code from it, will mean at SUSPEND_PREPARE
notification, the card will be removed before proceeding with the
suspend sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For every bus_ops type the .remove callback always exist, thus there
are no need to check the existence of it, before we decide to call it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the new eMMC5.1 spec, there is a new EXT_CSD register with
the revision number(EXT_CSD_REV) 7. This patch updates the check
for ext-csd.rev number as 7.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In addition to just logging errors encountered during DT parsing or
allocating GPIO slots for CD/WP, mmc_of_parse() now returns with an error.
In particular, this is needed if the GPIO allocation may return
EPROBE_DEFER.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the saved values in card->ext_csd when selecting power class.
By doing this the power class will be selected even if mmc_init_card
is called with oldcard != NULL, which is the case after a suspend/resume.
Today ext_csd is NULL if mmc_init_card is called with oldcard != NULL
and power class will not be selected.
According to the eMMC specification the POWER_CLASS value is reset after
power failure, H/W reset assertion and any CMD0 reset.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Reviewed-by: Johan Rudholm <jrudholm@gmail.com>
Acked By: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mmc_card_sleep|awake APIs are not being used since the support is
already properly encapsulated within the suspend sequence. Sleep|awake
command is also specific for eMMC.
We remove the sleep|awake bus_ops, the mmc_card_sleep|awake APIs and
move the code into the mmc specific core instead. This also includes
the mmc ops function, mmc_sleepawake. All releated functions have then
become static and we have got far less code to maintain.
Additionally this patch also simplifies the code from mmc_sleepawake,
since it is only used to put the card to sleep and not awake.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Aggressive power management is suitable when saving power is
essential. At request inactivity timeout, aka pm runtime
autosuspend timeout, the card will be suspended.
Once a new request arrives, the card will be re-initalized and
thus the first request will suffer from a latency. This latency
is card-specific, experiments has shown in general that SD-cards
has quite poor initialization time, around 300ms-1100ms. eMMC is
not surprisingly far better but still a couple of hundreds of ms
has been observed.
Except for the request latency, it is important to know that
suspending the card will also prevent the card from executing
internal house-keeping operations in idle mode. This could mean
degradation in performance.
To use this feature make sure the request inactivity timeout is
chosen carefully. This has not been done as a part of this patch.
Enable this feature by using host cap MMC_CAP_AGGRESSIVE_PM and
by setting CONFIG_MMC_UNSAFE_RESUME.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Once the mmc blkdevice is being probed, runtime pm will be enabled.
By using runtime autosuspend, the power save operations can be done
when request inactivity occurs for a certain time. Right now the
selected timeout value is set to 3 s. Obviously this value will likely
need to be configurable somehow since it needs to be trimmed depending
on the power save algorithm.
For SD-combo cards, we are still leaving the enablement of runtime PM
to the SDIO init sequence since it depends on the capabilities of the
SDIO func driver.
Moreover, when the blk device is being suspended, we make sure the device
will be runtime resumed. The reason for doing this is that we want the
host suspend sequence to be unaware of any runtime power save operations
done for the card in this phase. Thus it can just handle the suspend as
the card is fully powered from a runtime perspective.
Finally, this patch prepares to make it possible to move BKOPS handling
into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be
accomplished.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO is the only protocol that uses runtime pm for the card device
right now. To provide the option for sd and mmc to use runtime pm as
well the bus_ops callback are extended with two new functions. One for
runtime_suspend and one for runtime_resume.
This patch will also implement the callbacks for SDIO to make sure
existing functionality is maintained. It also prepares to move
away from using the mmc_power_restore_host API, since it is not
needed when using runtime PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move mmc suspend specific operations to be executed from the .suspend
callback in the mmc bus_ops. This simplifies the mmc_suspend_host
function which is supposed to handle nothing but common suspend tasks.
Since eMMC can be considered non-removable there are no need to check
for ongoing bkops at PM_SUSPEND_PREPARE notification so remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sanitize support is added as a user-app ioctl call, and
was removed from the block-device request, since its purpose is
to be invoked not via File-System but by a user.
This feature deletes the unmap memory region of the eMMC card,
by writing to a specific register in the EXT_CSD.
unmap region is the memory region that was previously deleted
(by erase, trim or discard operation).
In order to avoid timeout when sanitizing large-scale cards,
the timeout for sanitize operation is 240 seconds.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously the MMC_CAP2_DETECT_ON_ERR was invented for detecting
slow card removal. In was never a realy good solution and a proper
fix has been merged using gpio debouncing instead. We remove this
cap in this patch.
Although when using polling card detect mode, the code invented for
MMC_CAP2_DETECT_ON_ERR is re-used to complete card removal in an
earlier phase. There are no need waiting for the polling timeout to
elapse in this case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only execute tuning for sd and sdio devices that are using
SDR50 or SDR104.
Make sure clock is hold during tuning for sdio devices.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Acked-by: Johan Rudholm <jrudholm@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping mmc_power_up()
at boot/initialization time if it's already happened, for performance
(faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being put
into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed slowly;
we were missing card removal events if the card retained contact with
the slot pads for long enough to reply to a CMD13 while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use mmc_of_parse().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Pr7P
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.10:
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping
mmc_power_up() at boot/initialization time if it's already
happened, for performance (faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being
put into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed
slowly; we were missing card removal events if the card retained
contact with the slot pads for long enough to reply to a CMD13
while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property
support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use
mmc_of_parse()"
* tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: sdhci-tegra: fix MODULE_DEVICE_TABLE
mmc: core: fix init controller performance regression, updated patch
mmc: mxcmmc: enable DMA support on mpc512x
mmc: mxcmmc: constify mxcmci_devtype
mmc: mxcmmc: use slot-gpio API for write-protect detection
mmc: mxcmmc: add mpc512x SDHC support
mmc: mxcmmc: fix race conditions for host->req and host->data access
mmc: mxcmmc: DT support
mmc: dw_mmc: let device core setup the default pin configuration
mmc: mxs-mmc: add broken-cd property
mmc: mxs-mmc: add non-removable property
mmc: mxs-mmc: add cd-inverted property
mmc: core: call pm_runtime_put_noidle in pm_runtime_get_sync failed case
mmc: mxcmmc: Fix bug when card is present during boot
mmc: core: fix performance regression initializing MMC host controllers
Revert "mmc: core: wait while adding MMC host to ensure root mounts successfully"
mmc: atmel-mci: pio hang on block errors
mmc: core: Fix bit width test failing on old eMMC cards
mmc: dw_mmc: Use pr_info instead of printk
mmc: dw_mmc: Check return value of regulator_enable
...
Use preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add MMC_CAP2_NO_PRESCAN_POWERUP to sdhci-pci.c also, use mmc_power_off()
for MMC_CAP2_NO_PRESCAN_POWERUP.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[cjb: previously applied v1 of this patch instead of v4]
Signed-off-by: Chris Ball <cjb@laptop.org>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put_noidle in such case.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit fa5501890d introduced a performance
regression by adding mmc_power_up() to mmc_start_host(). mmc_power_up()
is not necessary to host controller initialization, it is part of card
initialization and is performed anyway asynchronously.
This patch allows a driver to leave the power up in asynchronous code
(as it was before).
On my current target platform this reduces driver initialization from:
[ 1.313220] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 102008 usecs
to this:
[ 1.217209] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 8331 usecs
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 3500ed90b2.
The reverted patch caused a significant performance regression when
booting with the root file system on eMMC.
Before the patch:
[ 1.625623] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
After the patch:
[ 1.935851] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
That was an addition of 310 ms which is a 19% performance degradation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
PARTITION_SUPPORT needs to be set before doing the compare on version
number so the bit width test does not get invalid data. Before this
patch, a Sandisk iNAND eMMC card would detect 1-bit width although
the hardware supports 4-bit.
Only affects old emmc devices - pre 4.4 devices.
Reported-by: Elad Yi <elad.yi@gmail.com>
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC hosts are added asynchronously. We need to wait until detect returns to
avoid failed root filesystem mounts.
VFS: Cannot open root device "mmcblk0p1" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
mmc0: host does not support reading read-only switch. assuming write-enable.
1f00 256 mtdblock0 (driver?)
1f01 256 mtdblock1 (driver?)
1f02 2560 mtdblock2 mmc0: new SDHC card at address b368
(driver?)
1f03 29696 mtdblock3 (driver?)
1f04 16384 mtdblock4 mmcblk0: mmc0:b368 USD 3.72 GiB
(driver?)
mmcblk0: p1
b300 3910656 mmcblk0 driver: mmcblk
b301 3906560 mmcblk0p1 00000000-01
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ACPI spec 5 defined the _ADR encoding for sdio bus as:
High word - slot number (0 based)
Low word - function number
This patch adds support for binding sdio function device with acpi node,
and if successful, involve acpi into its power management.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Function _mmc_detect_card_removed will be called to know whether
the card is still present when host->bus_ops->detect is called.
In current code, the return value of this function generally only
depend on the result of sending cmd13 to card, which may not safe
for card with detection support like slot gpio detection.
Because the communication status between host and card may out of
sync with the detect status if remove the card slowly or hands shake
during the process. The direct reason is the async between card
detect switch and card/slot pad contaction in hardware, which is
defined by spec.
The spec define card insert/remove sequence as below (both standard size
SD card and MicroSD card have the same sequence):
"Part 1 Standard Size SD Card Mechanical Addendum Ver4.00 Final,
Appendix C: Card Detection Switch" (Take normally open type as example)
a)SD card insertion sequence:
The card detection switch should be turned on after all SD card
contact pads are connected to the host connector contact pads.
b)SD removal sequence:
The card detection switch should be turned off when the SD card
is just going to be removed and before any SD card contact pad is
disconnected from the host connector contact pad.
Below is the sequence when this issue occur (Take slot gpio detection
as example and remove the card slowly during the process):
1. gpio level changed and card detect interrupt triggered.
2. mmc_rescan was launched.
3. the card pads were still contacted with the slot pads because of slow
removal. So _mmc_detect_card_removed and mmc_rescan think card was
still present (cmd13 succeed).
4. card pads were discontacted from the card slot pads.
So the card was actually removed finally but the card removal event
has been missed by system.
The interval length between step 1 and step 4 depends on the
card removal speed. If it's longer than the detect work schedule
delay which is 200ms, this issue will likely happen.
This patch add the card detect status check in function
_mmc_detect_card_removed if cmd13 check succeed and host->ops->get_cd
provided. If get_cd detect no card present then schedule another detect
work 200ms later.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The JEDEC MMC v4 spec defines a new PRV value in place of the original
fwrev and hwrev specified in v1. We can expose this in the kernel to enable
user space to more easily determine the product revision of a given MMC.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJRKmwHAAoJEHNBYZ7TNxYMNBYP/2FZRY33nrnJ0yKeMpyfdH+C
LN+33imQudA2t86FlbAOocvcpM12oTPy+DkIbFchWhN1O4lzrqMos8/527QUm9qL
cyCnZXrbst/Ttrs3UIbfkKNhA1m4Wau/taNPJ0fWqdmZU4424O774xSOyyB8m9x/
DKuPIs6B9AfVAlS+OM8ZtviIvsJRgC6amZ0mNQZIKGHPm7vCTg6n35tP1ux7ZvJQ
4dMlgqRalV+xN9gNBnCVLOc2eSwEyxIJA2m13LTHGf72pkNvSdYrID87qTJbvXOl
Ed7PHuU3+M5bHw7ErCkbi8rmwuSuc8omNt9WK+syGLx4g7v7GceIYHNQudatdN7O
gYUWnufT6Om6y+6h9QJ5td4ZZ7i6MhfC1Ps8hJCUjiVn+cLKlEPj0KmLAhZm+6cu
wuBdCujeAFu7Z5VcaO2TBLHXXsgggnWbpoq7v6fucCNIleBe598Nu2YJAdbMc+W4
8mONN4ANslTw7CAMrL3C99Ab1WVLZenX38schgDisTkGnI8dr/JCD4OpqAnPSKql
qD5KCKRb8O4BMZpQxiFwyTzqYpmNM9RkaIykLxY5y26lgwFI+At9wh1HnhFC4Hl/
ReJ5Cnm8sH19Vgz+5zpZzzS5/aCssObdfFImIfw1wWzwk9A8EHSjAZsVUkzXiVd4
yRwz6eeO3gBMZ+v2humV
=dYdW
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
Many MMC capability flags are platform-dependent and are traditionally set
in platform data. With DT often each such capability requires a special
binding. Add bindings for MMC_CAP_SD_HIGHSPEED, MMC_CAP_MMC_HIGHSPEED,
MMC_CAP_POWER_OFF_CARD and MMC_CAP_SDIO_IRQ capabilities. Also add code to
DT parser to look up "keep-power-in-suspend" and "enable-sdio-wakeup"
bindings and set MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ respectively,
if found.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch supports packed write command of eMMC4.5 devices. Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally. As a result, packed command help
write throughput be improved. The following tables show the results
of packed write.
Type A:
test none | packed
iozone 25.8 | 31
tiotest 27.6 | 31.2
lmdd 31.2 | 35.4
Type B:
test none | packed
iozone 44.1 | 51.1
tiotest 47.9 | 52.5
lmdd 51.6 | 59.2
Type C:
test none | packed
iozone 19.5 | 32
tiotest 19.9 | 34.5
lmdd 22.8 | 40.7
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds packed command feature of eMMC4.5. The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_regulator_set_ocr() depends on the ability of regulator to change the
voltage value. When regulator cannot change its voltage output, some code
is skipped to avoid reporting false errors on some boards, which use MMC
hosts with fixed regulators (e.g. Samsung Goni and UniversalC210 boards).
This patch replaces a hacky workaround based on regulator_count_voltages()
value with the correct call to recently introduced
regulator_can_change_voltage() function in regulators core.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is derived from:
"mmc: fix async request mechanism for sequential read scenarios".
According as async transfer, a request is handled with twice mmc_start_req.
When the card is removed, the request is actually not issued in the first
mmc_start_req [__mmc_start_data_req]. And then mmc_wait_for_data_req_done
will come in the next mmc_start_req. But there is no event for completions.
wake_up_interruptible is needed in __mmc_start_data_req for the case of
removed card.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.
Below are the enhancements introduced by this patch:
1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one. The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.
2. In current code, preset value is disabled at the beginning of
mmc_attach_sd. It's too late since low freq (400khz) should be set in
mmc_power_up. So move preset value disable to sdhci_set_ios which will
be called during power up.
3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.
4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.
This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
clock should be gated for 5 ms during the step. After enabling the
clock, the host should wait for at least 1 ms before checking for
failure. Failure by the card to switch is indicated by dat[0:3] being
pulled low. The host should check for this condition and power-cycle
the card if failure is indicated.
Add a retry mechanism for the SDIO case.
If the voltage switch fails repeatedly, give up and continue the
initialization using the original voltage.
This patch places a couple of requirements on the host driver:
1) mmc_set_ios with ios.clock = 0 must gate the clock
2) mmc_power_off must actually cut the power to the card
3) The card_busy host_ops member must be implemented
if these requirements are not fulfilled, the 1.8V signal voltage switch
will still be attempted but may not be successful.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.
Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add mmc_power_cycle which can be used to power cycle for instance
SD-cards.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
SET_BLOCK_COUNT CMD23 is needed for all access to RPMB partition. If
block count is not set by CMD23, all subsequent read/write commands fail
as per eMMC specification. So, If the host does not support CMD23, do not
expose RPMB partition.
Accessing RPMB partition can cause hang / huge delay for hosts which do
not support CMD23.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-and-Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cache control is an eMMC feature and in therefore should be
part of MMC's bus resume operations, performed in mmc_suspend,
rather than in the generic mmc_suspend_host().
Signed-off-by: Maya Erez <merez@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When current request is running on the bus and if next request fetched
by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the
current request completes. This means that if new request comes in while
the mmcqd thread is blocked, this new request can not be prepared in
parallel to current ongoing request. This may result in delaying the new
request execution and increase it's latency.
This change allows to wake up the MMC thread on new request arrival.
Now once the MMC thread is woken up, a new request can be fetched and
prepared in parallel to the current running request which means this new
request can be started immediately after the current running request
completes.
With this change read throughput is improved by 16%.
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use devm_* managed functions, so that slot-gpio users do not have to
call mmc_gpio_free_ro/cd to free up resources requested in
mmc_gpio_request_ro/cd.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When SDIO3.0 card is detected, incorrect bus speed mode
is printed as part of card detection print in kernel logs.
This change fixes it so that user won't be confused by
looking at incorrect card detection message in logs.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Jackey Shen <Jackey.Shen@amd.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to UHS-I initialization sequence for SDIO 3.0 cards,
the host must set bit[24] (S18R) of OCR register during OCR
handshake to know whether the SDIO card is capable of doing
1.8V I/O.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If SDIO keep power flag (MMC_PM_KEEP_POWER) is not set, card would
be reinitialized during resume but as we are not resetting
(CMD52 reset) the SDIO card during this reinitialization, card may
fail to respond back to subsequent commands (CMD5 etc...).
This change resets the card before the reinitialization of card
during resume.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Chris Ball <cjb@laptop.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Chris Ball <cjb@laptop.org>
The slot-gpio API provides a generic card-detection handler. To support a
wider range of hosts it has to call the host's card-event callback, if
implemented. Also increase the debounce interval to 200ms to match the
SDHCI driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ulf Hansson