Keep the panel_list ordered according to aliases. The DRM connectors will
be created following the panel_list. By keeping the list ordered the DRM
connectors will be created in the same order regardless of the driver
probe order.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of 'guessing' based on aliases of the status of the DSS drivers,
use the new interface to check that all needed drivers are loaded.
In this way we can be sure that all needed drivers are loaded so it is
safe to continue the probing of omapdrm.
This method will allow the omapdrm to be probed 'headless', without
outputs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapdss is loaded (all core components are in place) create a list of
devices used in the display graph. This list later can be used by omapdrm
via the omapdss_stack_is_ready() function to check that these components
are loaded. Based on this information, omapdrm can defer probe in case when
the omapdss stack is not ready yet.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions can be used to check a component (by it's of_node) if it is
part of the omapdss display or output list. If the component is found, it
means that the driver is loaded.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS uses "replication logic" to convert color components from smaller
bit widths to bigger bit widths. Without replication logic, the color
component would be shifted and the least significant bits would be left
at 0, whereas with replication logic, the least significat bits will be
filled with the most significant bit.
For some reason omapdrm leaves replication logic always to off, which,
in the most common case, means that showing 16-bit RGB colors on 24-bit
display gives a bit darker colors than expected.
The reset value of the replication logic bit is enabled, and it should
always be set, as there's no practical reason to disable it. This patch
removes the option to disable it from omapdrm, and always sets it to
enabled in dispc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdrm now uses dispc_ops instead of direct function calls so we can
remove all EXPORT_SYMBOLs from dispc. Most of the functions can also be
made static, but a few are used outside dispc.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change omapdrm to get dispc_ops and use that to call the dispc functions
instead or direct function calls.
The change is very straightforward.
The only problem was in omap_crtc_init() which calls pipe2vbl(crtc), and
at that point of time the crtc->dev link, which is used to get the
dispc_ops, has not been set up yet. This patch makes omap_crtc_init()
skip the call to pipe2vbl() and instead calls
dispc_ops->mgr_get_vsync_irq() directly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch changes the current omapdss driver to fill a dispc_ops struct
and set it to omapdss-base.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We want to change the dispc API from plain functions to a struct with
functions pointers, so that omapdrm can call either omapdss or omapdss6
depending on the platform.
This patch adds 'struct dispc_ops' and adds functions to omapdss-base
to set and get the ops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm still uses a few non-dispc functions: dss_feat_get_num_mgrs(),
dss_feat_get_num_ovls() and dss_feat_get_supported_color_modes(). We
want to provide omapdrm a single dispc_ops function pointer struct so
that omapdrm will use either the current omapdss or the new omapdss6
driver depending on the platform.
Those three functions are really dispc functions, but are located in the
dss_features.c for legacy reasons.
This patch adds similar functionss to the dispc, and changes omapdrm to
use those new functions. Underneath the functions still call the
functions from dss_feature.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch moves the common parts of omapdss to omapdss-base so that
both the current omapdss driver and the new omapdss6 driver can use
them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
display.c uses dsi_get_pixel_size() which is implemented in the DSI
driver, and we won't have that in the omapdss-base module, to which we
want to move display.c
This patch changes display.c not to use dsi_get_pixel_size(). The call
can be replaced with a simple check for OMAP_DSS_DSI_FMT_RGB565.
We can also make dsi_get_pixel_size() static as it's no longer used
outside dsi.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We don't have omapdss's custom error printing functions in the common
omapdss-base module, to which we want to move output.c.
This patch changes output.c to use dev_err instead of DSSERR so that it
doesn't depend on DSSERR.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdss_is_initialized() is used to find out if omapdss has been probed
successfully. This patch moves the related code to the common
omapdss-base module, so that the same support will be there for both
omapdss and omapdss6.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are working towards enabling omapdss6, which will consists of a new
dss, dispc and dpi drivers. omapdss6 will be a new module. The panel,
encoder and omapdrm will need to use either the current omapdss driver
or the new omapdss6 driver, depending on the platform.
This will be implemented with a common base module and function
pointers.
This patch adds a skeleton omapdss-base.ko module, to which we'll be
moving common dss functionality like registration of the panels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While implementing writeback support, odd behavior of WBDELAYCOUNT was
observed with the combination of WB capture and HDMI. The result of the
debugging was that the HDMI sync polarities are not set correctly.
The current code sets the sync polarities going from HDMI WP to DISPC
according to the video mode used, which seems to work normally fine, but
causes problems with WB as WB expects the syncs to be active-high.
This patch changes the HDMI sync polarities so that the DISPC always
gets active-high syncs from HDMI WP, and the HDMI core gets sync
polarities according to the used video mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Add support for render nodes in omap driver and allow required
ioctls to be accessible via render nodes.
This enables unprivileged clients to allocate resources like GEM buffers
for rendering their content into. Mode setting (KMS ioctls) is not
allowed using render nodes. These buffers are then shared with
a previleged process (e.g compositor) that has mode setting access.
An example of this use case is Android where the hardware composer is
the only master and has mode setting access. Every other client then
uses render node(e.g /dev/dri/renderD128 to allocate and use its buffers.
Signed-off-by: Hemant Hariyani <hemanthariyani@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock source selection for the LCD outputs is too hardcoded at the
moment. For example, LCD3 is set to use PLL2_1, and PLL2 doesn't exist
on DRA72x SoCs.
There are quite many ways to configure the clocks, even using HDMI PLL
for LCD outputs, but enabling full configuration of the clocks is rather
tricky.
This patch improves the situation a bit by checking if the PLL about to
be used exists, and if not, tries another one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
mode_config's min_width and min_height are both set to 32, which is
overly restrictive.
The real limits depend on whether we're configuring a crtc or a plane,
but a limit of 8x2 is safe for both cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The driver only uses even dividers for hsdiv when pclk >= 100MHz, as odd
dividers can create uneven duty cycle. However, while this holds true
for some dividers like DISPC's LCK and PCK dividers, it is not actually
true for hsdiv.
hsdiv always produces even duty cycle, so the constraint can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The current driver doesn't expose any of the CRTC HW properties like
background color or transparency key, and sets them at CRTC enable time.
Refactor this into a separate function and call that function from
omap_crtc_atomic_flush(). This is the behavior we want when the
properties can be configured, so this patch makes it easier to add
patches later which implement those properties.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRA7 errata i886 (FPDLink PLL Unlocks With Certain SoC PLL M/N Values)
says that FPDLink is sensitive to jitter on the vout clock, and that low
PLL M and N values result in more jitter than high M and N values.
This patch implements a workaround for the problem by changing the PLL
setup to search for clocks starting from high M and N values, instead of
low values. This should not cause any functional change, and only
reduces the jitter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYzznuAAoJEHm+PkMAQRiGAzMIAJDBo5otTMMLhg8eKj8Cnab4
2NyaoWDN6mtU427rzEKEfZlTtp3gIBVdFex5x442weIdw6BgRQW0dvF/uwEn08yI
9Wx7VJmIUyH9M8VmhDtkUTFrhwUGr29qb3JhENMd7tv/CiJaehGRHCT3xqo5BDdu
xiyPcwSkwP/NH24TS91G87gV6r0I0oKLSAxu+KifEFESrb8gaZaduslzpEj3m/Ds
o9EPpfzaiGAdW5EdNfPtviYbBk7ZOXwtxdMV+zlvsLcaqtYnFEsJZd2WyZL0zGML
VXBVxaYtlyTeA7Mt8YYUL+rDHELSOtCeN5zLfxUvYt+Yc0Y6LFBLDOE5h8b3eCw=
=uKUo
-----END PGP SIGNATURE-----
BackMerge tag 'v4.11-rc3' into drm-next
Linux 4.11-rc3 as requested by Daniel
omap_gem_dmabuf_mmap() returns an error (with a WARN) when called for a
buffer which is allocated with dma_alloc_*(). This prevents dmabuf mmap
from working on SoCs without DMM, e.g. AM4 and OMAP3.
I could not find any reason for omap_gem_dmabuf_mmap() rejecting such
buffers, and just removing the if() fixes the limitation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
First slice of drm-misc-next for 4.12:
Core/subsystem-wide:
- link status core patch from Manasi, for signalling link train fail
to userspace. I also had the i915 patch in here, but that had a
small buglet in our CI, so reverted.
- more debugfs_remove removal from Noralf, almost there now (Noralf
said he'll try to follow up with the stragglers).
- drm todo moved into kerneldoc, for better visibility (see
Documentation/gpu/todo.rst), lots of starter tasks in there.
- devm_ of helpers + use it in sti (from Ben Gaignard, acked by Rob
Herring)
- extended framebuffer fbdev support (for fbdev flipping), and vblank
wait ioctl fbdev support (Maxime Ripard)
- misc small things all over, as usual
- add vblank callbacks to drm_crtc_funcs, plus make lots of good use
of this to simplify drivers (Shawn Guo)
- new atomic iterator macros to unconfuse old vs. new state
Small drivers:
- vc4 improvements from Eric
- vc4 kerneldocs (Eric)!
- tons of improvements for dw-mipi-dsi in rockchip from John Keeping
and Chris Zhong.
- MAINTAINERS entries for drivers managed in drm-misc. It's not yet
official, still an experiment, but definitely not complete fail and
better to avoid confusion. We kinda screwed that up with drm-misc a
bit when we started committers last year.
- qxl atomic conversion (Gabriel Krisman)
- bunch of virtual driver polish (qxl, virgl, ...)
- misc tiny patches all over
This is the first time we've done the same merge-window blackout for
drm-misc as we've done for drm-intel for ages, hence why we have a
_lot_ of stuff queued already. But it's still only half of drm-intel
(room to grow!), and the drivers in drm-misc experiment seems to work
at least insofar as that you also get lots of driver updates here
alredy.
* tag 'drm-misc-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-misc: (141 commits)
drm/vc4: Fix OOPSes from trying to cache a partially constructed BO.
drm/vc4: Fulfill user BO creation requests from the kernel BO cache.
Revert "drm/i915: Implement Link Rate fallback on Link training failure"
drm/fb-helper: implement ioctl FBIO_WAITFORVSYNC
drm: Update drm_fbdev_cma_init documentation
drm/rockchip/dsi: add dw-mipi power domain support
drm/rockchip/dsi: fix insufficient bandwidth of some panel
dt-bindings: add power domain node for dw-mipi-rockchip
drm/rockchip/dsi: remove mode_valid function
drm/rockchip/dsi: dw-mipi: correct the coding style
drm/rockchip/dsi: dw-mipi: support RK3399 mipi dsi
dt-bindings: add rk3399 support for dw-mipi-rockchip
drm/rockchip: dw-mipi-dsi: add reset control
drm/rockchip: dw-mipi-dsi: support non-burst modes
drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
drm/rockchip: vop: test for P{H,V}SYNC
drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC
drm/rockchip: dw-mipi-dsi: use specific poll helper
drm/rockchip: dw-mipi-dsi: improve PLL configuration
drm/rockchip: dw-mipi-dsi: properly configure PHY timing
...
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use a more common logging style.
Miscellanea:
o Coalesce formats and realign arguments
o Neaten a few macros now using pr_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/76355db47b31668bb64d996865ceee53bd66b11f.1488285953.git.joe@perches.com
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYr5aeAAoJEAx081l5xIa+ZK4P/RD3XUsduYqziVFCRQ2n0X8r
+D92F4peTnSeSq7ZcZvprv+fezUGAHbfsWFs8feYCI5quUO6pEQSPwN+wyGazUi0
4hUVB/K9Iq7U/Bj7Z/SmsU3NuWJnkNqbmvSFvUdqYK9D/kl+Tnllzap2N4cTzjwu
GZOObz4n85cx94NqC3qw+7/ptL1X2MhXa+z0MzbkKyas84Bko1LwCSHRHsDKUnJc
IcSpOcYZ6pSRMIsKH4Kd79Go4vWm7djXT9XL3PwDk2NcXXUOuR+cfdHqYchYaM/O
iD2hvaSywBcflxSAml5x6vlXraoRd91ZZulgOObXtFfnUXdZB81TVq4uv6LU4Bx3
jLFixUZuk/TJT+W/8N10l7M6yMIFaTpNoNMc5n4IF5RNNyWba4BKnrI+f+lQiOpY
mmjIaidb0t5BICnJzCD264RhCEXmP0HaDV+iQQV6y6jJRXfd1bgnOXLKP73JekzB
TsbDshCoE7UO0dJ7n0LFpXSTQDTYzlazoEp14f2kFBxir5/l7r67nUlnDTvUQfuN
tSRvpN/s0wqvH3o7zhmpHxyJ/ZasPMQjNCFAuUEbx8L5SKXsua0FubIzN4aVpilb
XvfdFRWM/lkOT/q+8cGI/TcE3YTqEmALmGxdV/akbdNCiCg6aClyCLRE/DZhgmSQ
UMFjr9wlHl5Qo/OqLKj0
=Yjfg
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
Let's disable all scaling that requires horizontal decimation with
higher factor than 4, until we have better estimates of what we can
and can not do. However, NV12 color format appears to work Ok with
all decimation factors.
When decimating horizontally by more that 4 the dss is not able to
fetch the data in burst mode. When this happens it is hard to tell if
there enough bandwidth. Despite what theory says this appears to be
true also for 16-bit color formats.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move drm_atomic_helper_commit_modeset_enables() call to before
drm_atomic_helper_commit_planes() call and have a
omap_atomic_wait_for_completion() call after both.
With the current dss dispc implementation we have to enable the new
modeset before we can commit planes. The dispc ovl configuration
relies on the video mode configuration been written into the HW when
the ovl configuration is calculated.
This approach is not ideal because after a mode change the plane
update is executed only after the first vblank interrupt. The dispc
implementation should be fixed so that it is able use uncommitted drm
state information. information.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit dadf4659d0.
If planes are not disabled when the they are not on any crtc anymore
they will remain active and may show as "ghosts" when the crtc they
were last on is active again.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook. So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-3-git-send-email-shawnguo@kernel.org
Noticed that everyone duplicates the same logic here and we could safe
a few lines per driver. Yay for lots of drivers to make such tiny
refactors worth-while!
v2: Forgot to git add everything :(
v3: Actually remove release_fbi (Sean, Emil, Chris) ...
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207161603.17611-1-daniel.vetter@ffwll.ch
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
- cleanups&fixes for dw-hdmi bride driver (Laurent)
- updates for adv bridge driver (John Stultz) for nexus
- drm_crtc_from_index helper rollout (Shawn Guo)
- removing drm_framebuffer_unregister_private from drivers&core
- target_vblank (Andrey Grodzovsky)
- misc tiny stuff
* tag 'drm-misc-next-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc: (49 commits)
drm: qxl: Open code teardown function for qxl
drm: qxl: Open code probing sequence for qxl
drm/bridge: adv7511: Re-write the i2c address before EDID probing
drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally
drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection
drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context
drm: vc4: use crtc helper drm_crtc_from_index()
drm: tegra: use crtc helper drm_crtc_from_index()
drm: nouveau: use crtc helper drm_crtc_from_index()
drm: mediatek: use crtc helper drm_crtc_from_index()
drm: kirin: use crtc helper drm_crtc_from_index()
drm: exynos: use crtc helper drm_crtc_from_index()
dt-bindings: display: dw-hdmi: Clean up DT bindings documentation
drm: bridge: dw-hdmi: Assert SVSRET before resetting the PHY
drm: bridge: dw-hdmi: Fix the name of the PHY reset macros
drm: bridge: dw-hdmi: Define and use macros for PHY register addresses
drm: bridge: dw-hdmi: Detect PHY type at runtime
drm: bridge: dw-hdmi: Handle overflow workaround based on device version
...
The main change here is the IRQ code cleanup, which gives us properly working
vblank counts and timestamps. We also get much less calls to runtime PM gets &
puts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYc1sMAAoJEPo9qoy8lh71mecP/A5LUkARdvodJ5XWaez2asjn
MiaZ8s7hS1n6ieVPdrL916Nq5IQTwOTDX/cxFgnWEKIr/WU/le4ytX0mQBDcMqcY
SWFVRSBD0p0iA3UmCyN03G49IhAhUGIJ/E/wYr+o/XmJ4Qdr1LY1p+Qxf3o6vSbK
WfC3EESk5r9OIOYhBG8+uJuZ0Jxq+XuSCnZfX6tENDVEtjvsuJPjsN5spjlXDnww
mj+Z6Xr7Myag+tsmazEyItRQhHFXE4wlkhSJv57Dj5P2zyRvXmjyeOQhpoKKuWJZ
yO+t52HXs1qUHpG8hFG3ykka1hhyGMII7me+qeFIVLoiHpJrOyyeyvzQA9sCv3C7
qrPICT/hbrg8bFKhSeo9iZCO55VVDfnjh4vCpIvaekwKQLnDwyTnGRahvVCUVe9u
mNKAWhmBMJlYkpJT/cSmLbS/IinuRjYdc/Eq2ov9KbLMPOoN3KdJ+6+acY59gc+y
R1LLAfQIb/eZY1oGYXyszMqioBVETigdqePHAlmzajfcm9355E9o6ruQUh0fIbC8
MXBl4MpgwsbTp7IpZw1SweKPqRMuKE0Todp2Bjekmsca/HYNzV+7L4m5MnfSeLjI
SdYuEorJTolzXaJ03SmX5BGsHQdMWjyActz7U1i7zQTSFW8Kg/6jaO392J6lowZ7
LaHPpwvEysv2U/IsuZ8Y
=8XSw
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm changes for 4.11
The main change here is the IRQ code cleanup, which gives us properly working
vblank counts and timestamps. We also get much less calls to runtime PM gets &
puts.
* tag 'omapdrm-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (26 commits)
drm/omap: panel-sony-acx565akm.c: Add MODULE_ALIAS
drm/omap: dsi: fix compile errors when enabling debug prints
drm: omapdrm: Perform initialization/cleanup at probe/remove time
drm: Move vblank cleanup from unregister to release
drm: omapdrm: Use sizeof(*var) instead of sizeof(type) for structures
drm: omapdrm: Remove global variables
drm: omapdrm: Simplify IRQ wait implementation
drm: omapdrm: Inline the pipe2vbl function
drm: omapdrm: Don't call DISPC power handling in IRQ wait functions
drm: omapdrm: Remove unused parameter from omap_drm_irq handler
drm: omapdrm: Don't expose the omap_irq_(un)register() functions
drm: omapdrm: Keep vblank interrupt enabled while CRTC is active
drm: omapdrm: Use a spinlock to protect the CRTC pending flag
drm: omapdrm: Prevent processing the same event multiple times
drm: omapdrm: Check the CRTC software state at enable/disable time
drm: omapdrm: Let the DRM core skip plane commit on inactive CRTCs
drm: omapdrm: Replace DSS manager state check with omapdrm CRTC state
drm: omapdrm: Handle OCP error IRQ directly
drm: omapdrm: Handle CRTC error IRQs directly
drm: omapdrm: Handle FIFO underflow IRQs internally
...
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But omapdrm is using
drm_framebuffer_remove and a free-standing fb, so this is rendundant.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-4-git-send-email-daniel.vetter@ffwll.ch
Back to regular -misc pulls with reasonable sizes:
- dma_fence error clarification (Chris)
- drm_crtc_from_index helper (Shawn), pile more patches on the m-l to roll
this out to drivers
- mmu-less support for fbdev helpers from Benjamin
- piles of kerneldoc work
- some polish for crc support from Tomeu and Benjamin
- odd misc stuff all over
* tag 'drm-misc-next-2017-01-09' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
dma-fence: Introduce drm_fence_set_error() helper
dma-fence: Wrap querying the fence->status
dma-fence: Clear fence->status during dma_fence_init()
drm: fix compilations issues introduced by "drm: allow to use mmuless SoC"
drm: Change the return type of the unload hook to void
drm: add more document for drm_crtc_from_index()
drm: remove useless parameters from drm_pick_cmdline_mode function
drm: crc: Call wake_up_interruptible() each time there is a new CRC entry
drm: allow to use mmuless SoC
drm: compile drm_vm.c only when needed
fbmem: add a default get_fb_unmapped_area function
drm: crc: Wait for a frame before returning from open()
drm: Move locking into drm_debugfs_crtc_crc_add
drm/imx: imx-tve: Remove unused variable
Revert "drm: nouveau: fix build when LEDS_CLASS=m"
drm: Add kernel-doc for drm_crtc_commit_get/put
drm/atomic: Fix outdated comment.
drm: reference count event->completion
gpu: drm: mgag200: mgag200_main:- Handle error from pci_iomap
drm: Document deprecated load/unload hook
...
The integer returned by the unload hook is ignored by the drm core, so
let's make it void.
This patch was created using the following Coccinelle semantic script
(except for the declaration and comment in drm_drv.h):
Compile-tested only.
// <smpl>
@ get_name @
struct drm_driver drv;
identifier fn;
@@
drv.unload = fn;
@ replace_type @
identifier get_name.fn;
@@
- int
+ void
fn (...)
{
...
}
@ remove_return_param @
identifier get_name.fn;
@@
void fn (...)
{
<...
if (...)
return
- ...
;
...>
}
@ drop_final_return @
identifier get_name.fn;
@@
void fn (...)
{
...
- return 0;
}
// </smpl>
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Christian König <christian.koenig@amd.com>.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170106175731.29196-1-krisman@collabora.co.uk
First -misc pull for 4.11:
- drm_mm rework + lots of selftests (Chris Wilson)
- new connector_list locking+iterators
- plenty of kerneldoc updates
- format handling rework from Ville
- atomic helper changes from Maarten for better plane corner-case handling
in drivers, plus the i915 legacy cursor patch that needs this
- bridge cleanup from Laurent
- plus plenty of small stuff all over
- also contains a merge of the 4.10 docs tree so that we could apply the
dma-buf kerneldoc patches
It's a lot more than usual, but due to the merge window blackout it also
covers about 4 weeks, so all in line again on a per-week basis. The more
annoying part with no pull request for 4 weeks is managing cross-tree
work. The -intel pull request I'll follow up with does conflict quite a
bit with -misc here. Longer-term (if drm-misc keeps growing) a
drm-next-queued to accept pull request for the next merge window during
this time might be useful.
I'd also like to backmerge -rc2+this into drm-intel next week, we have
quite a pile of patches waiting for the stuff in here.
* tag 'drm-misc-next-2016-12-30' of git://anongit.freedesktop.org/git/drm-misc: (126 commits)
drm: Add kerneldoc markup for new @scan parameters in drm_mm
drm/mm: Document locking rules
drm: Use drm_mm_insert_node_in_range_generic() for everyone
drm: Apply range restriction after color adjustment when allocation
drm: Wrap drm_mm_node.hole_follows
drm: Apply tight eviction scanning to color_adjust
drm: Simplify drm_mm scan-list manipulation
drm: Optimise power-of-two alignments in drm_mm_scan_add_block()
drm: Compute tight evictions for drm_mm_scan
drm: Fix application of color vs range restriction when scanning drm_mm
drm: Unconditionally do the range check in drm_mm_scan_add_block()
drm: Rename prev_node to hole in drm_mm_scan_add_block()
drm: Fix O= out-of-tree builds for selftests
drm: Extract struct drm_mm_scan from struct drm_mm
drm: Add asserts to catch overflow in drm_mm_init() and drm_mm_init_scan()
drm: Simplify drm_mm_clean()
drm: Detect overflow in drm_mm_reserve_node()
drm: Fix kerneldoc for drm_mm_scan_remove_block()
drm: Promote drm_mm alignment to u64
drm: kselftest for drm_mm and restricted color eviction
...
Add module alias for Sony ACX565AKM LCD panel. This makes it probe on Nokia
N900 when panel driver is built as a module.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi.c compile fails if PRINT_VERBOSE_VM_TIMINGS is enabled, as the
video timings were not converted in the code behind that ifdef. Note
that PRINT_VERBOSE_VM_TIMINGS has to be enabled by hand, there's no
config option for it.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tomi.valkeinen@ti.com: fixed the patch description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Including all drivers. I thought about keeping small compat functions
to avoid having to change all drivers. But I really like the
drm_printer idea, so figured spreading it more widely is a good thing.
v2: Review from Chris:
- Natural argument order and better name for drm_mm_print.
- show_mm() macro in the selftest.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483009764-8281-1-git-send-email-daniel.vetter@ffwll.ch
The drm driver .load() operation is prone to race conditions as it
initializes the driver after registering the device nodes. Its usage is
deprecated, inline it in the probe function and call drm_dev_alloc() and
drm_dev_register() explicitly.
For consistency inline the .unload() handler in the remove function as
well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
By linking the sizeof to a variable type the code will be less prone to
bugs due to future type changes of variables.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move the list of pending IRQ wait instances to the omap_drm_private
structure and the wait queue head to the IRQ wait structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the IRQ list is used for IRQ wait only we can merge
omap_drm_irq and omap_irq_wait and simplify the implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function is only used in omap_irq.c and is just a wrapper around
dispc_mgr_get_vsync_irq(). Remove it and call the dispc function
directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The IRQ wait functions are called from the DSS enable and disable
operations only, where the DISPC is guaranteed to be enabled. There's no
need for manual DISPC power management there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The only omap_drm_irq handler doesn't use the irqstatus parameter passed
to the function. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The IRQ registration functions are not used outside of their compilation
unit, make them static. As the __omap_irq_(un)register() functions are
only called by their omap_irq_(un)register() counterparts, merge them
together.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of going through a complicated private IRQ registration
mechanism, handle the vblank interrupt activation with the standard
drm_crtc_vblank_get() and drm_crtc_vblank_put() mechanism. This will let
the DRM core keep the vblank interrupt enabled as long as needed to
update the frame counter.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The CRTC pending flag will need to be accessed atomically in the vblank
interrupt handler, memory barriers won't be enough to protect it. Use a
spinlock instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vblank interrupt is disabled after one occurrence, preventing the
atomic update event from being processed twice. However, this also
prevents the software frame counter from being updated correctly that
would require vblank interrupts to be kept enabled while the CRTC is
active.
In preparation for vblank interrupt fixes, make sure that the atomic
update event will be processed once only when the vblank interrupt will
be kept enabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm DSS manager enable/disable operations check the DSS manager
state to avoid double enabling/disabling. Check the CRTC software state
instead to decrease the dependency of the DRM layer to the DSS layer.
The dispc_mgr_is_enabled() function then be turned into a static
function, but needs to be moved up in its compilation unit to avoid a
forward declaration.
Add a WARN_ON to catch double enable or disable that should be prevented
by the DRM core and would be a clear sign of a bug. The warning should
eventually be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM core supports skipping plane update for inactive CRTCs for
hardware that don't need it or can't cope with it. That's our case, and
the driver already skips flushing planes on inactice CRTCs.
We can't remove the check from the driver, as active CRTCs are disabled
at the hardware level when an atomic flush is performed if a mode set is
pending. There's however no need to forward the plane commit calls to
the driver, so use the DRM core infrastructure to skip them with a
detailed comment to explain why the check must still be kept in the
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of conditioning planes update based on the DSS manager hardware
state, use the enabled field newly added to the omap_crtc structure.
This reduces the dependency from the DRM layer to the DSS layer.
The enabled field is a transitory measure, the implementation should use
the CRTC atomic state instead. However, given that CRTCs are currently
not enabled/disabled through their .enable() and .disable() operations
but through a convoluted code paths starting at the associated encoder
operations, there is not clear guarantee that the atomic state always
matches the hardware state. This will be refactored later, at which
point the enabled field will be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of going through a complicated registration mechanism, just
call the OCP error IRQ handler directly from the main IRQ handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of going through a complicated registration mechanism, just
expose the CRTC error IRQ function and call it directly from the main
IRQ handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the FIFO underflow IRQ handler just prints an error message to the
kernel log, simplify the code by not registering one IRQ handler per
plane but print the messages directly from the main IRQ handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Don't print userspace parameters validation failures as error messages
to avoid giving userspace the ability to flood the kernel log.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hardware requires all planes to have an identical pitch in number of
pixels. Given that all supported formats use the same number of bytes
per pixel in all planes, framebuffer creation checks can be simplified.
The implementations assumes that no format use more than two planes
which is true with the existing hardware.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merge the single-user objects_lookup inline function into its caller,
allowing reuse of the error code path.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver stores in a custom structure named format several pieces of
information about the format that are available in the DRM core. Remove
them and get the information from the DRM core instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The only multi-planar format supported by the driver is NV12, there will
thus never be more than two planes per framebuffer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Every single user of vmf->virtual_address typed that entry to unsigned
long before doing anything with it so the type of virtual_address does
not really provide us any additional safety. Just use masked
vmf->address which already has the appropriate type.
Link: http://lkml.kernel.org/r/1479460644-25076-3-git-send-email-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tpd12s015 driver is missing error value handling for gpio
initialization, causing 0 to be returned as an error if gpiod_get_*
fails. This may cause deferred probing to fail.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We set the possible_crtc for all planes to "(1 << priv->num_crtcs) - 1",
which is fine as the HW planes can be used fro all crtcs. However, when
we're doing that, we are still incrementing 'num_crtcs', and we'll end
up with bad possible_crtcs, preventing the use of the primary planes.
This patch passes a possible_crtcs mask to plane init function so that
we get correct possible_crtc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to the datasheet of the panel, both data, DEN and sync signals
are expected to be driven on the falling edge of the DOTCLK.
The DE is active low according to the documentation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to the datasheet of the panel, both data, DEN and sync signals
are expected to be driven on the falling edge of the DOTCLK.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to the datasheet of the panel, both data, DEN and sync signals
are expected to be driven on the falling edge of the DOTCLK.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to the datasheet of the panel, both data, DEN and sync signals
are expected to be driven on the falling edge of the DOTCLK.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use 'vm' to refer to a struct videomode instead of 'p', 't', 'timings' or
something else.
The code will be easier to follow if we use consistent names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_video_timings can be replaced with the generic videomode in omapdrm
and the omap_video_timings can be removed.
This patch will replace the omap_video_timings with videomode.
With the change we no longer need the functions to convert to/from
videomode and drm_display_mode to omap_video_timings, these can be removed
as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_video_timings struct have the same members as struct videomode, but
their types are different. As first step change the types of the
omap_video_timings struct members to match their counterpart in
struct videomode to catch any type cast related issues.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for sync edge.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for pixel data edge.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for double_pixel mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for DE level.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for h/vsync level.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of passing the omap_video_timings structure's members individually,
use the pointer to the struct.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove the interlace member and add display_flags to omap_video_timings to
configure the interlace mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
By using a pointer to the omap_mode_timings struct we can unwrap lines to
make the code easier to follow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the vbp member to vback_porch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the vfp member to vfront_porch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the vsw member to vsync_len.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the hbp member to hback_porch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the hfp member to hfront_porch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the hsw member to hsync_len.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the y_res member to vactive.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the x_res member to hactive.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix the retrn value check which testing the wrong variable
in dsi_bind().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It might be possible that the page has been unmapped already in
omap_gem_cpu_sync() so check before calling dma_unmap_page().
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_plane_atomic_update() does WARN_ON() if dispc rejects the given
plane config. Change that to dev_err() to lessen the possible spam.
To fix this correctly, the plane setup needs much more work by creating
a check function for dispc setup, so that we could reliably check the
config in atomic_check, instead of only noticing the problem when
programming dispc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up omap_plane_atomic_check() with:
- Check state->fb first. If no fb, return 0.
- use drm_atomic_get_existing_crtc_state() instead of
drm_atomic_get_crtc_state()
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
I sometimes see:
[drm:drm_framebuffer_remove [drm]] *ERROR* failed to reset crtc ed2a6c00
when fb was deleted: -22
which comes from drm_framebuffer_remove() when it's disabling the crtc
with zeroed drm_mode_set.
The problem in omap_plane_atomic_check() is that it will use those
zeroed fields to verify if the setup is correct.
This patch makes omap_plane_atomic_check() return 0 if the crtc is
disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The global mode_config.rotation_property is going away, switch over to
per-plane rotation_property.
Not sure I got the annoying crtc rotation_property handling right.
Might work, or migth not.
v2: Drop the BIT()
Don't create rotation property twice for each primary plane
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[danvet: Add comment per discussion between Tomi&Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1474907460-10717-8-git-send-email-ville.syrjala@linux.intel.com
0 isn't a valid rotation property value, so let's set the initial value
of the property to BIT(DRM_ROTATE_0) instead.
v2: Drop the BIT()
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1474907460-10717-7-git-send-email-ville.syrjala@linux.intel.com
We have intel_rotation_90_or_270() in i915 to check if the rotation is
90 or 270 degrees. Similar checks are elsewhere in drm, so let's move
the helper into a central place and use it everwhere.
v2: Drop the BIT()
Convert all new intel_rotation_90_or_270() calls
Deal with superfluous code shuffling
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1474907460-10717-2-git-send-email-ville.syrjala@linux.intel.com
drm_atomic_state has a complicated single owner model that tracks the
single reference from allocation through to destruction on another
thread - or perhaps on a local error path. We can simplify this tracking
by using reference counting (at a cost of a few more atomics). This is
even more beneficial when the lifetime of the state becomes more
convoluted than being passed to a single worker thread for the commit.
v2: Double check !intel atomic_commit functions for missing gets
v3: Update kerneldocs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161014121833.439-27-chris@chris-wilson.co.uk
Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
The drivers have to modify the atomic plane state during the prepare_fb
callback so they track allocations, reservations and dependencies for
this atomic operation involving this fb. In particular, how else do we
set the plane->fence from the framebuffer!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160818180017.20508-1-chris@chris-wilson.co.uk
This reverts
commit 2ab9f58791
Author: Peter Chen <peter.chen@nxp.com>
Date: Fri Jul 15 11:17:03 2016 +0800
gpu: drm: omapdrm: dss-of: add missing of_node_put after calling of_parse_phandle
The of_get_next_parent will drop refcount on the passed node, so the reverted
patch is wrong, thanks for Tomi Valkeinen points it.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1470908694-16362-1-git-send-email-peter.chen@nxp.com
Merge drm updates from Dave Airlie:
"This is the main drm pull request for 4.8.
I'm down with a cold at the moment so hopefully this isn't in too bad
a state, I finished pulling stuff last week mostly (nouveau fixes just
went in today), so only this message should be influenced by illness.
Apologies to anyone who's major feature I missed :-)
Core:
Lockless GEM BO freeing
Non-blocking atomic work
Documentation changes (rst/sphinx)
Prep for new fencing changes
Simple display helpers
Master/auth changes
Register/unregister rework
Loads of trivial patches/fixes.
New stuff:
ARM Mali display driver (not the 3D chip)
sii902x RGB->HDMI bridge
Panel:
Support for new panels
Improved backlight support
Bridge:
Convert ADV7511 to bridge driver
ADV7533 support
TC358767 (DSI/DPI to eDP) encoder chip support
i915:
BXT support enabled by default
GVT-g infrastructure
GuC command submission and fixes
BXT workarounds
SKL/BKL workarounds
Demidlayering device registration
Thundering herd fixes
Missing pci ids
Atomic updates
amdgpu/radeon:
ATPX improvements for better dGPU power control on PX systems
New power features for CZ/BR/ST
Pipelined BO moves and evictions in TTM
GPU scheduler improvements
GPU reset improvements
Overclocking on dGPUs with amdgpu
Polaris powermanagement enabled
nouveau:
GK20A/GM20B volt and clock improvements.
Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
exynos:
Exynos5433 SoC with IOMMU support.
vc4:
Shader validation for branching
imx-drm:
Atomic mode setting conversion
Reworked DMFC FIFO allocation
External bridge support
analogix-dp:
RK3399 eDP support
Lots of fixes.
rockchip:
Lots of small fixes.
msm:
DT bindings cleanups
Shrinker and madvise support
ASoC HDMI codec support
tegra:
Host1x driver cleanups
SOR reworking for DP support
Runtime PM support
omapdrm:
PLL enhancements
Header refactoring
Gamma table support
arcgpu:
Simulator support
virtio-gpu:
Atomic modesetting fixes.
rcar-du:
Misc fixes.
mediatek:
MT8173 HDMI support
sti:
ASOC HDMI codec support
Minor fixes
fsl-dcu:
Suspend/resume support
Bridge support
amdkfd:
Minor fixes.
etnaviv:
Enable GPU clock gating
hisilicon:
Vblank and other fixes"
* tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux: (1575 commits)
drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
drm/nouveau/acpi: fix lockup with PCIe runtime PM
drm/nouveau/acpi: check for function 0x1B before using it
drm/nouveau/acpi: return supported DSM functions
drm/nouveau/acpi: ensure matching ACPI handle and supported functions
drm/nouveau/fbcon: fix font width not divisible by 8
drm/amd/powerplay: remove enable_clock_power_gatings_tasks from initialize and resume events
drm/amd/powerplay: move clockgating to after ungating power in pp for uvd/vce
drm/amdgpu: add query device id and revision id into system info entry at CGS
drm/amdgpu: add new definition in bif header
drm/amd/powerplay: rename smum header guards
drm/amdgpu: enable UVD context buffer for older HW
drm/amdgpu: fix default UVD context size
drm/amdgpu: fix incorrect type of info_id
drm/amdgpu: make amdgpu_cgs_call_acpi_method as static
drm/amdgpu: comment out unused defaults_staturn_pro static const structure to fix the build
drm/amdgpu: enable UVD VM only on polaris
drm/amdgpu: increase timeout of IB test
drm/amdgpu: add destroy session when generate VCE destroy msg.
drm/amd: fix deadlock of job_list_lock V2
...
The following functions test whether their argument is NULL and then
return immediately.
* backlight_device_unregister
* drm_gem_object_unreference_unlocked
Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/72ff4670-4f3d-c7ed-4f37-e49f2bbc7aba@users.sourceforge.net
Backmerge drm-next to be able to apply Chris' connector_unregister_all
cleanup (need latest i915 and sun4i state for that).
Also there's a trivial conflict in ttm_bo.c that git rerere fails to
remember.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcHi9AAoJEHm+PkMAQRiGSJ0H/2o4t9VWYmhyPC1sdIHoCExJ
P4tBrcZYBmKcsOmIfnJDa5g/+IdhouEUM0v0fHPogS2UUWT9eRuJWYD3sY+HpEQ+
heKTli8X73gsFB25odeIbIt0jAoSiiMYWDrWqLNsuUV1tjEYVA8rH0SM94FiOC/5
7WVWXLTuH+Rm7JHP18BnKxmMMbzrTFmwisLMqFKyfZRRSlS+/ix7iLUNO9AFa39B
YHxNPihLrZ0oONyCOAQoHTIXXrw0cQbxV2utg3vnMcCZdme2xOn+iXMntTSKfZ39
iC9/T0vsO3R6OrRo2aDZAnCPUAniXnMEIhrKG37WMyXpj6cucZ/2QiNXcXviGV4=
=iLte
-----END PGP SIGNATURE-----
Back-merge tag 'v4.7-rc5' into drm-next
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
We already have a fallback in place to fill out the unique from
dev->unique, which is set to something reasonable in drm_dev_alloc.
Which means we only need to have a special set_busid for pci devices,
to be able to care the backwards compat code for drm 1.1 around, which
libdrm still needs.
While developing and testing this patch things blew up in really
interesting ways, and the code is rather confusing in naming things
between the kernel code, ioctl #defines and libdrm. For the next brave
dragon slayer, document all this madness properly in the userspace
interface section of gpu.tmpl.
v2: Make drm_dev_set_unique static and update kerneldoc.
v3: Entire rewrite, plus document what's going on for posterity in the
gpu docbook uapi section.
v4: Drop accidental amdgpu hunk (Emil).
v5: Drop accidental omapdrm vblank counter change (Emil).
v6: Rebase on top of the sphinx conversion.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (virt_gpu)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It's a legacy helper function which won't do good with atomic helpers.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465510479-21180-1-git-send-email-daniel.vetter@ffwll.ch
We have a 1:1 relationship between connectors and encoders and the
driver is relying on the atomic helpers: we can drop the custom
->best_encoder() implementation and let the core call
drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-17-git-send-email-boris.brezillon@free-electrons.com
* Update MAINTAINERS file for omapdrm and tilcdc
* PLL refactoring to allow versatile use of the PLL clocks
* Public omapdss header refactoring to separate omapfb and omapdrm
* Gamma table support
* Support reset GPIO and vcc regulator in omapdrm's panel-dpi
* Minor cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dSIF
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm changes for 4.8
* Update MAINTAINERS file for omapdrm and tilcdc
* PLL refactoring to allow versatile use of the PLL clocks
* Public omapdss header refactoring to separate omapfb and omapdrm
* Gamma table support
* Support reset GPIO and vcc regulator in omapdrm's panel-dpi
* Minor cleanups
* tag 'omapdrm-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (69 commits)
drm/omapdrm: Implement gamma_lut atomic crtc properties
drm/omapdrm: Workaround for errata i734 (LCD1 Gamma) in DSS dispc
drm/omapdrm: Add gamma table support to DSS dispc
drm: drm_helper_crtc_enable_color_mgmt() => drm_crtc_enable_color_mgmt()
drm/omap: rename panel/encoder Kconfig names
drm: omapdrm: add DSI mapping
drm: omapdrm: Remove unused omap_framebuffer_bo function
drm: omapdrm: Remove unused omap_gem_tiled_size function
drm: omapdrm: panel-lgphilips-lb035q02: Remove unused backlight GPIO
drm/omap: panel-dpi: implement support for a vcc regulator
drm/omap: panel-dpi: make (limited) use of a reset gpio
devicetree/bindings: add reset-gpios and vcc-supply for panel-dpi
MAINTAINERS: Add maintainer for TI LCDC DRM driver
MAINTAINERS: Add maintainer for OMAP DRM driver
drm/omap: fix pitch round-up
drm/omap: remove align_pitch()
drm/omap: remove unnecessary pitch round-up
drm/omap: remove unneeded gpio includes
drm/omap: Remove the video/omapdss.h and move it's content to local header file
[media] omap_vout: Switch to use the video/omapfb_dss.h header file
...
As promised, piles of prep work all around:
- drm_atomic_state rework, prep for nonblocking commit helpers
- fence patches from Gustavo and Christian to prep for atomic fences and
some cool work in ttm/amdgpu from Christian
- drm event prep for both nonblocking commit and atomic fences
- Gustavo seems on a crusade against the non-kms-native version of the
vblank functions.
- prep work from Boris to nuke all the silly ->best_encoder
implementations we have (we really only need that for truly dynamic
cases like dvi-i vs dvi-d or dp mst selecting the right transcoder on
intel)
- prep work from Laurent to rework the format handling functions
- and few small things all over
* tag 'topic/drm-misc-2016-06-07' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm/dsi: Implement set tear scanline
drm/fb_cma_helper: Implement fb_mmap callback
drm/qxl: Remove useless drm_fb_get_bpp_depth() call
drm/ast: Remove useless drm_fb_get_bpp_depth() call
drm/atomic: Fix remaining places where !funcs->best_encoder is valid
drm/core: Change declaration for gamma_set.
Documentation: add fence-array to kernel DocBook
drm/shmobile: use drm_crtc_vblank_{get,put}()
drm/radeon: use drm_crtc_vblank_{get,put}()
drm/qxl: use drm_crtc_vblank_{get,put}()
drm/atmel: use drm_crtc_vblank_{get,put}()
drm/armada: use drm_crtc_vblank_{get,put}()
drm/amdgpu: use drm_crtc_vblank_{get,put}()
drm/virtio: use drm_crtc_send_vblank_event()
drm/udl: use drm_crtc_send_vblank_event()
drm/qxl: use drm_crtc_send_vblank_event()
drm/atmel: use drm_crtc_send_vblank_event()
drm/armada: use drm_crtc_send_vblank_event()
drm/doc: Switch to sphinx/rst fixed-width quoting
drm/doc: Drop kerneldoc for static functions in drm_irq.c
...
lockless gem bo freeing patches (and the oddball related patch) for all
the drivers who's maintainers are asleep at the helm - includes you ;-)
I based this on top of drm-fixes to include Chris' fix for the cma issue.
* tag 'topic/lockless-gem-bo-freeing-2016-06-01' of git://anongit.freedesktop.org/drm-intel: (21 commits)
drm/arcpgu: Use lockless gem BO free callback
drm/sun4i: Use lockless gem BO free callback
drm/omapdrm: Nuke dummy fb->dirty callback
drm/msm: Nuke dummy fb->dirty callback
drm/rockchip: Use cma gem vm ops
drm/sti: Use lockless gem BO free callback
drm: sti: remove useless call to dev->struct_mutex
drm/virtio: Use lockless gem BO free callback
drm/tilcdc: Use lockless gem BO free callback
drm/shmob: Use lockless gem BO free callback
drm/rockchip: Use lockless gem BO free callback
drm/rcar-du: Use lockless gem BO free callback
drm/qxl: Use lockless gem BO free callback
drm/nouveau: Use lockless gem BO free callback
drm/mga200g: Use lockless gem BO free callback
drm/fls-dcu: Use lockless gem BO free callback
drm/cirrus: Use lockless gem BO free callback
drm/bochs: Use lockless gem BO free callback
drm/atmel: Use lockless gem BO free callback
drm/ast: Use lockless gem BO free callback
...
Implement gamma_lut atomic crtc properties, set crtc gamma size to 256
for all crtcs and use drm_atomic_helper_legacy_gamma_set() as
gamma_set func. The tv-out crtc has 1024 element gamma table (with
10bit precision) in HW, but current Xorg server does not accept
anything else but 256 elements so that is used for all CRTCs. The dss
dispc API converts table of any length for HW and uses linear
interpolation in the process. The default gamma table is restored
if gamma_lut property is deleted.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Workaround for errata i734 in DSS dispc
- LCD1 Gamma Correction Is Not Working When GFX Pipe Is Disabled
For gamma tables to work on LCD1 the GFX plane has to be used at least
once after DSS HW has come out of reset. The workaround sets up a
minimal LCD setup with GFX plane and waits for one vertical sync irq
before disabling the setup and continuing with the context
restore. The physical outputs are gated during the operation.
For details see:
OMAP543x Multimedia Device Silicon Revision 2.0 Silicon Errata
Literature Number: SWPZ037E
Or some other relevant errata document for the DSS IP version.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add gamma table support to DSS dispc.
DSS driver initializes the default gamma table at component bind time
and holds a copy of all gamma tables in its internal data structure.
Each call to dispc_mgr_set_gamma() updates the internal table and
triggers write to the HW, if it is enabled. The tables are restored to
HW in PM resume callback. The drivers internal data structure match
the HW tables in size and in number of significant bits per color
component. The dispc_mgr_set_gamma() converts the size of any given
table for the internal data structure using linear interpolation.
Default gamma table is restored if NULL is given in place of gamma
lut.
dispc_mgr_gamma_size() gives HW gamma table size for the channel and
returns 0 if gamma table is not supported by the HW or the DSS driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm is using much too generic Kconfig names for its panels and
encoders. Rename them to have "DRM_OMAP" in the name.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This sets proper connector type for DSI connected panels.
Signed-off-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function is never used, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function is never used, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The backlight GPIO was supported with platform data only. Now that the
driver only supports DT, the backlight GPIO is never initialized. Remove
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To allow supporting displays that need some logic to enable power to the
display try to get a vcc-supply property from the device tree and drive
the resulting regulator accordingly.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Some displays have a reset input. To assert that the display is
functional the reset gpio must be deasserted.
Teach the driver to get and drive such a gpio accordingly.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment we calculate the buffer's pitch with:
pitch = width * DIV_ROUND_UP(bpp, 8)
For CLUT modes with bpp of 1/2/4/8 this gives wrong result, and the
correct pitch is:
pitch = DIV_ROUND_UP(width * bpp, 8)
In practice this doesn't change anything, as we don't support CLUT
modes, but it's better to have the pitch calculation correct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The previous commit removed aligning the pitch to SGX's pitch
requirement from align_pitch(). What's left is effectively a function
that returns width * bytespp.
To clean up the driver, we can remove the function and have the
calculation inline in the two places which call align_pitch().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdrm checks if the pixel stride is divisible by 8. This is meant to
ensure that the byte stride is 32, which is required by SGX.
The check is not correct, as it checks for pixels, not bytes, and thus
needlessly increases the stride for, e.g., NV12.
Also, SGX driver is not supported in the mainline, and the TI's SGX
driver nowadays does the memory allocation itself and doesn't rely on
omapdrm to figure out the correct pitch.
So we can just remove the whole roundup.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
encoder-opa362.c and panel-sharp-ls037v7dw01.c do not use the legacy
GPIO API, so we can remove the including of gpio.h and of_gpio.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Move the contents of the video/omapdss.h header file to omapdrm/dss local
header file and remove the original global header. The omapfb stach is
using video/omapfb_dss.h so this change will complete the separation of the
two driver implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
All drivers to include the omapdrm/dss/omapdss.h header file. This header
includes the <video/omapdss.h>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Clean up the header files regarding to hdmi audio so the omap-hdmi-audio.h
file will only need to include the platform_data/omapdss.h file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Mark Brown <broonie@kernel.org>
CC: Jyri Sarha <jsarha@ti.com>
CC: Liam Girdwood <liam.r.girdwood@linux.intel.com>
The default_device is no longer used, it is a leftower from legacy. The
else if (pdata->default_device) is always going to be false.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
In legacy mode (non DT mode) support only composite connector type. The
only user for this is rx51, using composite type.
Dropping the connector_type selection via pdata will allow cleanups in
omapdss (drm vs fbdev).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Some panel/encoder/connector driver includes omap-panel-data.h but they
do not need it. Remove the inclusion of video/omap-panel-data.h from these
drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
We want to hide drm_atomic_stat internals a bit better.
v2: Use drm_crtc_mask (Maarten).
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464818821-5736-7-git-send-email-daniel.vetter@ffwll.ch
A lot of the display drivers for OMAP use the gpio descriptor functions
that are only available in linux/gpio.h if GPIOLIB is enabled and
otherwise produce a build error:
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c: In function 'opa362_enable':
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c:101:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-dpi.c: In function 'panel_dpi_probe_pdata':
drivers/gpu/drm/omapdrm/displays/panel-dpi.c:189:23: error: implicit declaration of function 'gpio_to_desc' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c: In function 'sharp_ls_enable':
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c:120:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
This replaces the existing linux/gpio.h with linux/gpio/consumer.h
where needed. In case of panel-lgphilips-lb035q02.c however, we
also have to include linux/gpio.h to get the definition of gpio_is_valid
and gpio_set_value_cansleep that are used for the non-DT case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[tomi.valkeinen@ti.com: resolved conflicts]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver relies on this header to be included
implicitly, but this does not always work, and I get
this error in randconfig builds:
gpu/drm/omapdrm/dss/hdmi_phy.c: In function 'hdmi_phy_dump':
gpu/drm/omapdrm/dss/hdmi_phy.c:34:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_wp.c: In function 'hdmi_wp_dump':
gpu/drm/omapdrm/dss/hdmi_wp.c:26:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_pll.c: In function 'hdmi_pll_dump':
gpu/drm/omapdrm/dss/hdmi_pll.c:30:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
This adds the #include statements in all files that have
a seq_printf statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit 1c278e5e37.
If DRM_OMAP does not select OMAP2_DSS it is possible to build a kernel with
DRM_OMAP only and not selecting OMAP2_DSS. Since omapdrm depends on
OMAP2_DSS this will result on broken kernel build.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regulator_can_change_voltage() is deprecated and it's use is not necessary
as commit:
6a0028b3dd regulator: Deprecate regulator_can_change_voltage()
describers it clearly.
Also, regulator_set_voltage() is misused in the driver, as it is
supposed to be used only in cases where the regulator voltage needs to
be changed dynamically at runtime. In DSS's case, we always want a fixed
voltage, set in the .dts files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DDC scl high and low times were set to the minimum values
from the i2c specification, but the i2c specification takes into
account the rise time and fall time to calculate the frequency.
To pass HDMI certification DDC can not exceed 100kHz therefore in
a system where the rise times and fall times are negligible the high
and low times for scl need to be 10us.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The AVI infoframe R0-R3 in the 2nd data byte represents the
Active Format Aspect Ratio. It is four bits long not two bits.
This fixes that mask used to extract the bits before writing the
bits to the hardware registers.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_core_powerdown_disable() is supposed to disable HDMI core's
power-down mode. However, the function sets the power-down bit to 0,
which means "enable power-down".
This hasn't caused any issues as the PD seems to affect only interrupts
from HDMI core, and none of those interrupts are used at the moment. CEC
functionality requires core interrupts, and the PD mode needs to be
fixed.
This patch fixes hdmi_core_powerdown_disable() to actually disable the
PD mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
With certain kernel config options many omapdrm files fail to compile
due to missing include of linux/gpio/consumer.h and linux/of.h.
This patch adds those includes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
In some configurations, we can build the OMAP dss driver without
implictly including the pinctrl consumer definitions, causing
a build error:
gpu/drm/omapdrm/dss/dss.c: In function 'dss_runtime_suspend':
gpu/drm/omapdrm/dss/dss.c:1268:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
This adds an explicit #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Originally DSS only had DSI PLLs, and thus the DPI driver has functions
and variables that refer to DSI or DSI PLL. Now we support DSI, VIDEO
and HDMI PLLs, so it's time to remove the DSI references from the code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Type A and B PLLs require a bit different calculations for the clock
rates. DPI driver supports only type A PLLs.
This patch adds support for the type B PLL.
Type B PLLs are simpler than type A, as type B can produce a good clock
for almost any rate. Thus we can just ask it to produce the pixel clock
and use one as LCK and PCK dividers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_pll_calc_b() takes HDMI TMDS clock rate as a parameter. To make
dss_pll_calc_b() usable for non-HDMI users, change the function to take
clkout rate as parameter, and also change the current users of
dss_pll_calc_b() to accommodate that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move hdmi_pll_compute(), used to calculate the config for HDMI PLL, from
hdmi_pll.c to pll.c, with the name of dss_pll_calc_b(), to make it
available to non-HDMI users.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a "_a" postfix to the type A PLL calc functions, to differentiate
them from the type B PLL calculations which we will add shortly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To make it possible to use HDMI PLL for other video outputs than HDMI,
the HDMI PLL code needs to do runtime_get/put for the HDMI IP, so that
the IP (include the PLL) is enabled.
To do that we also need to store the HDMI pdev in the hdmi_pll_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI driver uses a fixed clkout index, 0. This has worked fine as the
first clkout is usually used.
To generalize the code and to support additional clock sources, change
the code to use dss_pll_get_clkout_idx_for_src() to get the clkout
index.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can clean up the DPI driver's clock source handling by using the
dss_clk_source instead of only a dss_pll pointer.
This will also make it possible to use additional clock sources, like
PLL1_3 or HDMI_PLL, which the code did not support earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the new PLL helpers, we can clean up the dispc_fclk_rate(). This
will also make dispc_fclk_rate() support clock sources it didn't support
earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the new PLL helpers, we can clean up the dispc_mgr_lclk_rate().
This will also make dispc_mgr_lclk_rate() support clock sources it
didn't support earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add two PLL helper functions:
dss_pll_find_by_src() which returns the dss_pll for the given
dss_clk_source.
dss_pll_get_clkout_idx_for_src() which returns the clkout index for the
given dss_clk_source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The code to set the clock muxes for DISPC's LCD clock inputs is very
confusing. Especially on DRA7, there's an additional clock muxing that
needs to be done, which at the moment is done in dpi.c using
dss_ctrl_pll_set_control_mux().
Clean this all up by:
- Using dss_clk_source instead of dss_pll_id, as dss_pll_id doesn't
specify the clock source quite correctly.
- Splitting the dss_select_lcd_clk_source() up into DSS version specific
helper functions.
- Using dss_ctrl_pll_set_control_mux() from the helper functions, so
that dpi.c doesn't have to call it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS uses two types of PLLs, type A (DSI & Video) and type B (HDMI). The
two types behave slightly differently, but we don't have the type of the
PLL available anywhere for the driver.
This patch adds an enum for the PLL type and a field in the PLL's HW
data to store it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
enum dss_clk_source does not have values for all clock sources available
on OMAP4+ DSS versions. Add the missing clock sources.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The names of the enum dss_clk_source's values are legacy names, only
correct for OMAP3 DSS. Rename the names to more generic ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that there is no "non-generic" version of the function to get the
clock source name, lets rename dss_get_generic_clk_source_name() to
dss_get_clk_source_name().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have two functions to return a name for clock sources for debugging
purposes: dss_feat_get_clk_source_name() and
dss_get_generic_clk_source_name().
The former is supposed to return a DSS IP version specific name for the
clock source, and the latter is supposed to return a more generic name.
All this seems a bit pointless, so let's remove the former one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
'enum omap_dss_clk_source' is internal to dss. Let's rename it to
'dss_clk_source' match our naming convention.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment 'enum omap_dss_clk_source' is in omapdss.h, shared by
omapdrm and omapfb. We're about to improve the omapdrm clock code, so we
need to make a separate copy of the enum for each driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Video pll hw data is missing bitfield definitions for clkout2 and
clkout3. We don't use those clkouts at the moment, so this has not
caused any issues.
Add the bitfields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
drm_gem_object_lookup() has never required the drm_device for its file
local translation of the user handle to the GEM object. Let's remove the
unused parameter and save some space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fixup kerneldoc too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For drm_gem_object_unreference callers are required to hold
dev->struct_mutex, which these paths don't. Enforcing this requirement
has become a bit more strict with
commit ef4c6270bf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 15 09:36:25 2015 +0200
drm/gem: Check locking in drm_gem_object_unreference
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459330852-27668-3-git-send-email-daniel.vetter@ffwll.ch
Pull drm fixes from Dave Airlie:
"Just a couple of dma-buf related fixes and some amdgpu fixes, along
with a regression fix for radeon off but default feature, but makes my
30" monitor happy again"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/mst: cleanup code indentation
drm/radeon/mst: fix regression in lane/link handling.
drm/amdgpu: add invalidate_page callback for userptrs
drm/amdgpu: Revert "remove the userptr rmn->lock"
drm/amdgpu: clean up path handling for powerplay
drm/amd/powerplay: fix memory leak of tdp_table
dma-buf/fence: fix fence_is_later v2
dma-buf: Update docs for SYNC ioctl
drm: remove excess description
dma-buf, drm, ion: Propagate error code from dma_buf_start_cpu_access()
drm/atmel-hlcdc: use helper to get crtc state
drm/atomic: use helper to get crtc state
Bunch of small fixupes all over. Plus a dma-buf patch that Sumit asked me
to cherry-pick since that's the only one he had in his tree.
There's a sparse issue outstanding in the color mgr stuff, but Lionel is
still working on something that actually appeases sparse.
* tag 'topic/drm-misc-2016-03-22' of git://anongit.freedesktop.org/drm-intel:
dma-buf/fence: fix fence_is_later v2
dma-buf: Update docs for SYNC ioctl
drm: remove excess description
dma-buf, drm, ion: Propagate error code from dma_buf_start_cpu_access()
drm/atmel-hlcdc: use helper to get crtc state
drm/atomic: use helper to get crtc state
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.6 kernel.
Overall the coolest thing here for me is the nouveau maxwell signed
firmware support from NVidia, it's taken a long while to extract this
from them.
I also wish the ARM vendors just designed one set of display IP, ARM
display block proliferation is definitely increasing.
Core:
- drm_event cleanups
- Internal API cleanup making mode_fixup optional.
- Apple GMUX vga switcheroo support.
- DP AUX testing interface
Panel:
- Refactoring of DSI core for use over more transports.
New driver:
- ARM hdlcd driver
i915:
- FBC/PSR (framebuffer compression, panel self refresh) enabled by default.
- Ongoing atomic display support work
- Ongoing runtime PM work
- Pixel clock limit checks
- VBT DSI description support
- GEM fixes
- GuC firmware scheduler enhancements
amdkfd:
- Deferred probing fixes to avoid make file or link ordering.
amdgpu/radeon:
- ACP support for i2s audio support.
- Command Submission/GPU scheduler/GPUVM optimisations
- Initial GPU reset support for amdgpu
vmwgfx:
- Support for DX10 gen mipmaps
- Pageflipping and other fixes.
exynos:
- Exynos5420 SoC support for FIMD
- Exynos5422 SoC support for MIPI-DSI
nouveau:
- GM20x secure boot support - adds acceleration for Maxwell GPUs.
- GM200 support
- GM20B clock driver support
- Power sensors work
etnaviv:
- Correctness fixes for GPU cache flushing
- Better support for i.MX6 systems.
imx-drm:
- VBlank IRQ support
- Fence support
- OF endpoint support
msm:
- HDMI support for 8996 (snapdragon 820)
- Adreno 430 support
- Timestamp queries support
virtio-gpu:
- Fixes for Android support.
rockchip:
- Add support for Innosilicion HDMI
rcar-du:
- Support for 4 crtcs
- R8A7795 support
- RCar Gen 3 support
omapdrm:
- HDMI interlace output support
- dma-buf import support
- Refactoring to remove a lot of legacy code.
tilcdc:
- Rewrite of pageflipping code
- dma-buf support
- pinctrl support
vc4:
- HDMI modesetting bug fixes
- Significant 3D performance improvement.
fsl-dcu (FreeScale):
- Lots of fixes
tegra:
- Two small fixes
sti:
- Atomic support for planes
- Improved HDMI support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1063 commits)
drm/amdgpu: release_pages requires linux/pagemap.h
drm/sti: restore mode_fixup callback
drm/amdgpu/gfx7: add MTYPE definition
drm/amdgpu: removing BO_VAs shouldn't be interruptible
drm/amd/powerplay: show uvd/vce power gate enablement for tonga.
drm/amd/powerplay: show uvd/vce power gate info for fiji
drm/amdgpu: use sched fence if possible
drm/amdgpu: move ib.fence to job.fence
drm/amdgpu: give a fence param to ib_free
drm/amdgpu: include the right version of gmc header files for iceland
drm/radeon: fix indentation.
drm/amd/powerplay: add uvd/vce dpm enabling flag to fix the performance issue for CZ
drm/amdgpu: switch back to 32bit hw fences v2
drm/amdgpu: remove amdgpu_fence_is_signaled
drm/amdgpu: drop the extra fence range check v2
drm/amdgpu: signal fences directly in amdgpu_fence_process
drm/amdgpu: cleanup amdgpu_fence_wait_empty v2
drm/amdgpu: keep all fences in an RCU protected array v2
drm/amdgpu: add number of hardware submissions to amdgpu_fence_driver_init_ring
drm/amdgpu: RCU protected amd_sched_fence_release
...
Drivers, especially i915.ko, can fail during the initial migration of a
dma-buf for CPU access. However, the error code from the driver was not
being propagated back to ioctl and so userspace was blissfully ignorant
of the failure. Rendering corruption ensues.
Whilst fixing the ioctl to return the error code from
dma_buf_start_cpu_access(), also do the same for
dma_buf_end_cpu_access(). For most drivers, dma_buf_end_cpu_access()
cannot fail. i915.ko however, as most drivers would, wants to avoid being
uninterruptible (as would be required to guarrantee no failure when
flushing the buffer to the device). As userspace already has to handle
errors from the SYNC_IOCTL, take advantage of this to be able to restart
the syscall across signals.
This fixes a coherency issue for i915.ko as well as reducing the
uninterruptible hold upon its BKL, the struct_mutex.
Fixes commit c11e391da2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Feb 11 20:04:51 2016 -0200
dma-buf: Add ioctls to allow userspace to flush
Testcase: igt/gem_concurrent_blit/*dmabuf*interruptible
Testcase: igt/prime_mmap_coherency/ioctl-errors
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tiago Vignatti <tiago.vignatti@intel.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: intel-gfx@lists.freedesktop.org
Cc: devel@driverdev.osuosl.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458331359-2634-1-git-send-email-chris@chris-wilson.co.uk
The recent changes which removed platform data support from panels &
encoders had a few mistakes, causing probes of DVI connector and DSI
command mode panels to fail every time due to missing '!'. Fix the
if()s.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* HDMI interlace output support
* DMAbuf import support
* Big refactoring leading to removal of legacy code
* Various non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+fwk
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm changes for v4.6
* HDMI interlace output support
* DMAbuf import support
* Big refactoring leading to removal of legacy code
* Various non-critical fixes
* tag 'omapdrm-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (76 commits)
drm/omap: no need to select OMAP2_DSS
drm/omap: gem: Fix omap_gem_new() error path
drm/omap: remove -Werror from Makefile
drm/omap: remove dispc_ovl_check()
drm/omap: remove dss compat code
drm/omap: remove last uses of omap_overlay_manager
drm/omap: DSI: remove uses of omap_overlay_manager
drm/omap: VENC: remove uses of omap_overlay_manager
drm/omap: SDI: remove uses of omap_overlay_manager
drm/omap: HDMI4: remove uses of omap_overlay_manager
drm/omap: HDMI5: remove uses of omap_overlay_manager
drm/omap: DPI: remove uses of omap_overlay_manager
drm/omap: remove extra manager checks on disconnect
drm/omap: remove extra check in dpi and sdi
drm/omap: convert dss_mgr_unregister_framedone_handler to accept omap_channel
drm/omap: convert dss_mgr_register_framedone_handler to accept omap_channel
drm/omap: convert dss_mgr_start_update to accept omap_channel
drm/omap: convert dss_mgr_disable to accept omap_channel
drm/omap: convert dss_mgr_enable to accept omap_channel
drm/omap: convert dss_mgr_set_lcd_config to accept omap_channel
...
omapdss driver now depends on omapdrm, so we no longer should select
OMAP2_DSS from omapdrm's Kconfig.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When an error occurs in omap_gem_new() the function calls
omap_gem_free_object() to clean up. However, that function expects to be
called on a fully initialized GEM object and thus crashes.
Replace it by manual cleanup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have removed all the uses of compat code from omapdrm and the
non-compat parts of omapdss, so now we can remove all the compat code
itself.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have now removed all uses of 'struct omap_overlay_manager', so we can
now remove the last places where it is set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes DSI driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes VENC driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes SDI driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes HDMI4 driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes HDMI5 driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes DPI driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSS output drivers check 'dssdev->manager' in disconnect()
functions. This check is not needed as the manager must always be set if
the output device was connected. Remove the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Both dpi and sdi check for 'mgr != NULL' in check_timings. This check is
not necessary, as mgr must always be set before check_timings. Remove
the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_unregister_framedone_handler() to accept 'enum
omap_channel' instead of 'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_register_framedone_handler() to accept 'enum
omap_channel' instead of 'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_start_update() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_enable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_lcd_config() to accept 'enum omap_channel' instead
of 'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_timings() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disconnect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_connect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use 'out->dispc_channel_connected' to check if the device is connected
to an overlay manager or not, instead of using 'out->manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We want to remove the 'struct omap_overlay_manager' from
omap_dss_device. At the moment that field is used, among some other
uses, to see if the omap_dss_device is connected to an overlay manager.
To make it possible to remove the 'struct omap_overlay_manager' field,
this patch adds 'bool dispc_channel_connected' field to track the
connected-or-not status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the use of 'struct omap_overlay_manager' from omapdrm.
This patch changes the function pointers in 'dss_mgr_ops' to get 'enum
omap_channel' parameter instead of 'struct omap_overlay_manager'.
The change is very straightforward, as we still use 'struct
omap_overlay_manager' inside the function implementations where needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to remove uses of 'struct omap_overlay_manager' we need to get
rid of using omapdss_find_mgr_from_display() when initializing omapdrm.
Instead of using omapdss_find_mgr_from_display() and mgr->id to find the
dispc channel used for the given display, we can instead use
omapdss_find_output_from_display(), and get the output->dispc_channel
from there.
We can also remove omapdss_find_mgr_from_display() as it's no longer
used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to remove uses of 'struct omap_overlay_manager' from omapdrm,
this patch removes the crtc->mgr field.
To accomplish that, a new static array is added along the current
'omap_crtcs' static array, which is used to store the output device
connected to a crtc.
Optimally we'd use the struct omap_crtc to store this information, but
at the time when omap_crtc_dss_connect() is called, we don't yet have
the omap_crtc instances. This might possibly be fixed later, but for now
the static array does the job.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the use of the 'struct omap_overlay_manager' from
omapdrm, and one part of that is removing the use of
mgr->supported_outputs field.
This patch adds dispc_mgr_get_supported_outputs() function which can be
used instead of mgr->supported_outputs. omap_crtc.c is changed to use
the new function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch continues the work to create private versions of the
omapdss.h header for omapdrm and omapfb. This one moves the dss_mgr_*
function declarations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch continues the work to create private versions of the
omapdss.h header for omapdrm and omapfb. This one moves 'struct dss_mgr_ops'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm and omapfb still share the same include/video/omapdss.h. We need
to change that so that we can proceed with omapdrm work.
However, it's not trivial to make separate omapfb and omapdrm versions
of omapdss.h, as that file is also included in other places like arch
code, audio code and omap_vout code. So we'll do it piece by piece.
This patch makes private versions of all the dispc function declarations
that are in omapdss.h. For omapdrm we create a new file,
drivers/gpu/drm/omapdrm/dss/omapdss.h, which will contain headers meant
to be visible outside omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the connector, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the connector, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the encoder, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer have any boards that require the platform data support from
the panel, so we can remove the related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
core.c is the only caller of dss_disable_all_devices(). We can thus move
the function from display.c to core.c and make it static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For legacy reasons omapdss handles system suspend/resume via PM notifier
callback, where the driver disables/resumes all the outputs.
This doesn't work well with omapdrm. What happens on suspend is that the
omapdss disables the displays while omapdrm is still happily continuing
its work, possibly waiting for an vsync irq, which will never come if
the display output is disabled, leading to timeouts and errors sent to
userspace.
This patch moves the suspend/resume handling to omapdrm, and the
suspend/resume is now done safely inside modeset lock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm is missing a check on the validity of the rotation property.
This leads to omapdrm possibly trying to use rotation on non-rotateable
framebuffer, which causes the overlay setup to fail.
This patch adds the necessary check to omap_plane_atomic_check().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Before universal planes we had to have plane specific properties for the
crtc too, as on the hardware level a crtc uses a plane. In other words,
e.g. 'zorder' property was added to both planes and crtcs, and
omap_crtc.c would delegate the property set/get to the primary plane.
However, the delegation was a bit too generic, delegating all property
set/get calls to planes. Thus it's possible to set, say, FB_ID, on a
crtc, which gets redirected to the primary plane.
This is not standard, and shouldn't be allowed. To keep backward
compatibility, we still need to redirect the properties we supported
earlier for crtcs, namely 'zorder' and 'rotation'.
This patch redirects only the allowed properties from crtcs to planes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Subsequent threads returning EBUSY from vm_insert_pfn() was not
handled correctly. As a result concurrent access from new threads
to mmapped data caused SIGBUS.
See e79e0fe380 ("drm/i915: EBUSY status
handling added to i915_gem_fault()").
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The DSS hardware uses the same ROW_INC value for both Y and UV planes
for NV12 format. This means that the pitches of the Y and UV planes have
to match. omapdrm doesn't check this at the moment, and this can lead
into a broken NV12 fb on the screen.
This patch adds the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
DISPC requires the x resolution to be divisible by 8 when stall mode is
not used.
Add a check to the DPI driver to verify this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Now that interlace support has been added, we can remove the check that
prevents interlace.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Add the missing bits for interlace:
* Set VBLANK_OSC if the videomode's vblank is fractional
* Halve the vertical timings for interlace
* Double the horizontal timings for double-pixel mode
* Set FC_PRCONF properly for double-pixel mode
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The HDMI driver copies the timing values one by one. Instead we can just
copy the whole struct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
For some reason the HDMI FC's HSW value is programmed to hsw-1. There's
no indication in the documentation that this would be correct, and no
other blanking value needs -1 either.
So remove the -1.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Interlace field order is different between VENC and HDMI. The driver
currently sets the field order for VENC.
This patch adds the code to set the field order for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The HDMI WP timings are not programmed correctly for interlace.
We need to halve the vertical timings when interlace is used, and double
the horizontal timings when pixel doubling is used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On OMAP4 and OMAP5 ES1.0 the HDMI_WP_VIDEO_TIMING_H:HSW field is
set directly to the HSW value. On later SoCs the field needs to be
programmed with the value of HSW-1.
Currently the driver always programs the field with the HSW value. Most
videomodes seem to work fine with that, but at least low resolution
interlaced modes don't work at all.
This patch fixes the HSW for OMAP5 ES2.0+ SoCs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to HDMI to double the pixel clock when
double-pixel mode is used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to omapdrm to output double-pixel mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to DISPC to output double-pixel mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_crtc_wait_pending() waits until the config changes have been taken
into use, usually at next vblank. The wait-timeout used is 50ms, which
usually is enough, but in some rare cases not.
As time wait-timeout is just a safety measure for cases where something
is broken, we can just as well increase the timeout considerably.
This patch makes the timeout 250ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We no longer have the omapdrm plugin system for SGX, and we can thus
remove the support for external memory and sync objects from omap_gem.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
OMAP GEM objects backed by dma_buf reuse the current OMAP GEM object
support as much as possible. If the imported buffer is physically
contiguous its physical address will be used directly, reusing the
OMAP_BO_MEM_DMA_API code paths. Otherwise it will be mapped through the
TILER using a pages list created from the scatterlist instead of the
shmem backing storage.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the individual steps of GEM object allocation and initialization
clearly. This improves readability and prepares for dma_buf import
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver assumes that only objects backed by shmem need to be mapped
through DMM. While this is true with the current code, the assumption
won't hold with dma_buf import support.
Condition the mapping based on whether the buffer has been allocated
using the DMA mapping API instead and clean up the flags to avoid having
to check both flags and GEM object filp field to decide how to process
buffers. Flags are not the authoritative source of information regarding
where the buffer memory comes from, and are renamed to make that
clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the panel's enable fails, omap_encoder silently ignores the failure.
omapdrm should really handle the failure, but unfortunately the whole
encoder enable codepath is expected to always succeed.
So for now, catch the enable failure and print an error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_gem_dma_sync() calls dma_map_page() but does not check the possible
error with dma_mapping_error(). If DMA-API debugging is enabled, the
debug layer will give a warning if dma_mapping_error() has not been
used.
This patch adds proper error handling to omap_gem_dma_sync().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_gem_attach_pages() calls dma_map_page() but does not check the
possible error with dma_mapping_error(). If DMA-API debugging is
enabled, the debug layer will give a warning if dma_mapping_error() has
not been used.
This patch adds proper error handling to omap_gem_attach_pages().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
tpd12s015 HW has LS_OE, CT_CP_HPD and HPD gpios. Out of these gpios,
driver only handled LS_OE as optional. The CT_CP_HPD gpio should also
be treated as optional gpio as it is just a power saving feature. Some
boards hardwire this gpio to be always enable. In this patch, all access
to CT_CP_HPD gpio is made optional.
Signed-off-by: Manisha Agrawal <manisha.agrawal@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
All devices using tpd12s015 driver are doing DT boot. No need of further
supporting the platform data. This patch removes support for platform
data.
Signed-off-by: Manisha Agrawal <manisha.agrawal@ti.com>
[tomi.valkeinen@ti.com: minor adjustments]
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This patch adds wrapper functions for readl() and writel(), dmm_read()
and dmm_write(), so that we can implement workaround for DRA7 errata
i878.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The current driver uses non-blocking DMM fill when releasing memory.
This gives us a small performance increase as we don't have to wait for
the fill operation to finish.
However, the driver does not have any error handling for non-blocking
fill. In case of an error, the fill operation may silently fail, leading
to leaking DMM engines, which may eventually lead to deadlock if we run
out of DMM engines.
This patch makes the DMM driver always use blocking fills, so that we
can catch the errors. A more complex option would be to allow
non-blocking fills, and implement proper error handling, but that is
left for the future.
This patch is a HACK, as the proper fix is to either decide to always
use sync fills and remove all the async related code, or fix the async
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We occasionally see DISPC sync-lost errors when enabling and disabling
HDMI. Sometimes we get only a few, which get handled (ignored) by the
driver, but sometimes there's a flood of the errors which doesn't seem
to stop.
The HW team has root caused this to the order in which HDMI and DISPC
are enabled/disabled. Currently we enable HDMI first, and then DISPC,
and vice versa when disabling. HW team's suggestion is to do it the
other way around.
This patch changes the order, but this has two side effects as the pixel
clock is produced by HDMI, and the clock is not running when we
enable/disable DISPC:
* When enabling DISPC first, we don't get vertical sync events
* When disabling DISPC last, we don't get FRAMEDONE event
At the moment we use both of those to verify that DISPC has been
enabled/disabled properly. Thus this patch also needs to change the
omapdrm and omapdss which handle the DISPC side.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This patch removes range-based information used for optimizations in
begin_cpu_access and end_cpu_access.
We don't have any user nor implementation using range-based flush. It seems a
consensus that if we ever want something like that again (or even more robust
using 2D, 3D sub-range regions) we can use the upcoming dma-buf sync ioctl for
such.
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Tiago Vignatti <tiago.vignatti@intel.com>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1450820214-12509-3-git-send-email-tiago.vignatti@intel.com
First drm-misc pull req for 4.6. Big one is the drm_event cleanup, which
is also prep work for adding android fence support to kms (Gustavo is
planning to do that). Otherwise random small bits all over.
* tag 'topic/drm-misc-2016-02-08' of git://anongit.freedesktop.org/drm-intel: (33 commits)
gma500: clean up an excessive and confusing helper
drm/gma500: remove helper function
drm/vmwgfx: Nuke preclose hook
drm/vc4: Nuke preclose hook
drm/tilcdc: Nuke preclose hook
drm/tegra: Stop cancelling page flip events
drm/shmob: Nuke preclose hook
drm/rcar: Nuke preclose hook
drm/omap: Nuke close hooks
drm/msm: Nuke preclose hooks
drm/imx: Unconfuse preclose logic
drm/exynos: Remove event cancelling from postclose
drm/atmel: Nuke preclose
drm/i915: Nuke intel_modeset_preclose
drm: Nuke vblank event file cleanup code
drm: Clean up pending events in the core
drm/vblank: Use drm_event_reserve_init
drm/vmwgfx: fix a NULL dereference
drm/crtc-helper: Add caveat to disable_unused_functions doc
drm/gma500: Remove empty preclose hook
...
Again since the core takes care of this we can remove them. While at
it also remove the postclose hook, it's empty.
v2: Laurent pointed me at even more code to delete.
v3: Remove unused flags (Tomi).
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-9-git-send-email-daniel.vetter@ffwll.ch
* pxafb: device-tree support
* An unsafe kernel parameter 'lockless_register_fb' for debugging problems
happening while inside the console lock
* Small miscellaneous fixes & cleanups
* omapdss: add writeback support functions
* Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151 for longer story.
The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel drivers),
making further development of omapdrm difficult. After these patches omapfb and
omapdrm have their own versions of the drivers, which are more or less
direct copies for now but will diverge soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/) is
now in maintenance mode, and all new development will be done for omapdrm
(drivers/gpu/drm/omapdrm/).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nrji
-----END PGP SIGNATURE-----
Merge tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
"Summary:
- pxafb: device-tree support
- An unsafe kernel parameter 'lockless_register_fb' for debugging
problems happening while inside the console lock
- Small miscellaneous fixes & cleanups
- omapdss: add writeback support functions
- Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151
for longer story. The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel
drivers), making further development of omapdrm difficult. After
these patches omapfb and omapdrm have their own versions of the
drivers, which are more or less direct copies for now but will diverge
soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/)
is now in maintenance mode, and all new development will be done for
omapdrm (drivers/gpu/drm/omapdrm/)"
* tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (49 commits)
video: fbdev: pxafb: fix out of memory error path
drm/omap: make omapdrm select OMAP2_DSS
drm/omap: move omapdss & displays under omapdrm
omapfb: move vrfb into omapfb
omapfb: take omapfb's private omapdss into use
omapfb/displays: change CONFIG_DISPLAY_* to CONFIG_FB_OMAP2_*
omapfb/dss: change CONFIG_OMAP* to CONFIG_FB_OMAP*
omapdss: remove CONFIG_OMAP2_DSS_VENC from omapdss.h
omapfb: copy omapdss & displays for omapfb
omapfb: allow compilation only if DRM_OMAP is disabled
fbdev: omap2: panel-dpi: simplify gpio setting
fbdev: omap2: panel-dpi: in .disable first disable backlight then display
OMAPDSS: DSS: fix a warning message
video: omapdss: delete unneeded of_node_put
OMAPDSS: DISPC: Remove boolean comparisons
OMAPDSS: DSI: cleanup DSI_IRQ_ERROR_MASK define
OMAPDSS: remove extra out == NULL checks
OMAPDSS: change internal dispc functions to static
OMAPDSS: make a two dss feat funcs internal to omapdss
OMAPDSS: remove extra EXPORT_SYMBOLs
...
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.5. I don't think I've missed
anything too major, I'm mostly back at work now but I'll probably get
some sleep in 5 years time.
Summary:
New drivers:
- etnaviv:
GPU driver for the 3D core on the Vivante core used in numerous
ARM boards.
Highlights:
Core:
- Atomic suspend/resume helpers
- Move the headers to using userspace friendlier types.
- Documentation updates
- Lots of struct_mutex removal.
- Bunch of DP MST fixes from AMD.
Panel:
- More DSI helpers
- Support for some new basic panels
i915:
- Basic Kabylake support
- DP link training and detect code refactoring
- fbc/psr fixes
- FIFO underrun fixes
- SDE interrupt handling fixes
- dma-buf/fence support in pageflip path.
- GPU side for MST audio support
radeon/amdgpu:
- Drop UMS support
- GPUVM/Scheduler optimisations
- Initial Powerplay support for Tonga/Fiji/CZ/ST
- ACP audio prerequisites
nouveau:
- GK20a instmem improvements
- PCIE link speed change support
msm:
- DSI support for msm8960/apq8064
tegra:
- Host1X support for Tegra210 SoC
vc4:
- 3D acceleration support
armada:
- Get rid of struct mutex
tda998x:
- Atomic modesetting support
- TMDS clock limitations
omapdrm:
- Atomic modesetting support
- improved TILER performance
rockchip:
- RK3036 VOP support
- Atomic modesetting support
- Synopsys DW MIPI DSI support
exynos:
- Runtime PM support
- of_graph binding for DP panels
- Cleanup of IPP code
- Configurable plane support
- Kernel panic fixes at release time"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (711 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/amdgpu: add missing irq.h include
drm/vmwgfx: Fix a width / pitch mismatch on framebuffer updates
drm/vmwgfx: Fix an incorrect lock check
drm: nouveau: fix nouveau_debugfs_init prototype
drm/nouveau/pci: fix check in nvkm_pcie_set_link
drm/amdgpu: validate duplicates first
drm/amdgpu: move VM page tables to the LRU end on CS v2
drm/ttm: add ttm_bo_move_to_lru_tail function v2
drm/ttm: fix adding foreign BOs to the swap LRU
drm/ttm: fix adding foreign BOs to the LRU during init v2
drm/radeon: use kobj_to_dev()
drm/amdgpu: use kobj_to_dev()
drm/amdgpu/cz: force vce clocks when sclks are forced
drm/amdgpu/cz: force uvd clocks when sclks are forced
drm/amdgpu/cz: add code to enable forcing VCE clocks
drm/amdgpu/cz: add code to enable forcing UVD clocks
drm/amdgpu: fix lost sync_to if scheduler is enabled.
drm/amd/powerplay: fix static checker warning for return meaningless value.
drm/sysfs: use kobj_to_dev()
...
Merge second patch-bomb from Andrew Morton:
- more MM stuff:
- Kirill's page-flags rework
- Kirill's now-allegedly-fixed THP rework
- MADV_FREE implementation
- DAX feature work (msync/fsync). This isn't quite complete but DAX
is new and it's good enough and the guys have a handle on what
needs to be done - I expect this to be wrapped in the next week or
two.
- some vsprintf maintenance work
- various other misc bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (145 commits)
printk: change recursion_bug type to bool
lib/vsprintf: factor out %pN[F] handler as netdev_bits()
lib/vsprintf: refactor duplicate code to special_hex_number()
printk-formats.txt: remove unimplemented %pT
printk: help pr_debug and pr_devel to optimize out arguments
lib/test_printf.c: test dentry printing
lib/test_printf.c: add test for large bitmaps
lib/test_printf.c: account for kvasprintf tests
lib/test_printf.c: add a few number() tests
lib/test_printf.c: test precision quirks
lib/test_printf.c: check for out-of-bound writes
lib/test_printf.c: don't BUG
lib/kasprintf.c: add sanity check to kvasprintf
lib/vsprintf.c: warn about too large precisions and field widths
lib/vsprintf.c: help gcc make number() smaller
lib/vsprintf.c: expand field_width to 24 bits
lib/vsprintf.c: eliminate potential race in string()
lib/vsprintf.c: move string() below widen_string()
lib/vsprintf.c: pull out padding code from dentry_name()
printk: do cond_resched() between lines while outputting to consoles
...
Convert the raw unsigned long 'pfn' argument to pfn_t for the purpose of
evaluating the PFN_MAP and PFN_DEV flags. When both are set it triggers
_PAGE_DEVMAP to be set in the resulting pte.
There are no functional changes to the gpu drivers as a result of this
conversion.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
omap_encoder_update() assigns an overlay manager to
dssdev->src->manager. This assignment is not needed, as the connections
in the display chain have already been made at connect step.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm supports atomic modesetting, and it seems to work ok. So let's
set the flag to enable the atomic modesetting API support.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Remove unused defines related to SGX plugin which are not used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Modified Tiler placement to utilize bitmaps for bookkeeping and
all placement algorithms. This resulted in a substantial savings
in time for all Tiler reservation and free operations. Typical
savings are in the range of 28% decrease in time taken with larger
buffers showing a 80%+ decrease.
Signed-off-by: Andy Gross <andy.gross@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The GEM object can't be tiled without a usergart as that condition is
checked and considered as an error when creating the GEM object.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The goto error statement end up just returning NULL without performing
any cleanup, replace it with a direct return.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The drm_gem_free_mmap_offset() call in omap_gem_free_object() is
redundant as the same function is called from drm_gem_object_release().
Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the omap_gem_free_object() function to destroy the GEM object in the
omap_gem_new_handle() error path instead of doing it manually (and
incorrectly).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The GEM object free handler frees memory allocated by the driver using
the pointer to the drm_gem_object instead of the pointer to the
omap_gem_object that embeds it. This doesn't cause any issue in practice
as the drm_gem_object is the first field of omap_gem_object, but would
cause memory corruption if the structure layout changes. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The 8 high order bits of the buffer flags are reserved for internal use.
Mask them out from the flags passed by userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The structure contains data related to a device instance, it shouldn't
be a global variable.
While at it rename the usergart structures with an omap_drm_ prefix.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Divide the GEM implementation in groups of functions to improve
readability.
No code change is performed by this commit.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reorder functions to get rid of forward declarations
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Several DRM core function prototypes refer to functions that don't exist
anymore and are thus obviously never called. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Don't compile the fbdev emulation code when fbdev emulation support is
disabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The plane reset handler frees the plane state and allocates a new
default state, but when doing so attempt to free the plane state using
the base plane state pointer instead of casting it to the
driver-specific state object that has been allocated. Fix it by using
the omap_plane_atomic_destroy_state() function to destroy the plane
state instead of duplicating the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tomi.valkeinen@ti.com: move of the func into separate patch]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dmm_tiler.c can't be compiled as a module and it is built
unconditionally as part of omapdrm. Since it can't be used as a module,
there is no need for it to have an unused MODULE_ALIAS().
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that omapdss is only for omapdrm, we can change omapdrm to select
OMAP2_DSS to enable omapdss if omapdrm is enabled, instead of omapdrm
depending on omapdss.
We can also change omapdss and the display drivers to depend on
DRM_OMAP, so that they are only visible under omapdrm in menuconfig.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Now that omapfb has its own copy of omapdss and display drivers, we can
move omapdss and display drivers which omapdrm uses to omapdrm's
directory.
We also need to change the main drm Makefile so that omapdrm directory
is always entered, because omapdss has a file that can't be built as a
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
This merges '5b726e06d6e8309e5c9ef4109a32caf27c71dfc8' into drm-next
Just to resolve some merges to make Daniel's life easier.
Signed-off-by: DAve Airlie <airlied@redhat.com>
omap_fbdev always creates a framebuffer with ARGB8888 pixel format. On
OMAP3 we have VIDEO1 overlay that does not support ARGB8888, and on
OMAP2 none of the overlays support ARGB888.
This patch changes the omap_fbdev's fb to XRGB8888, which is supported
by all platforms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. It choked on
msm/mdp/mdp5/mdp5_plane.c like so:
"BAD:!!!!! enum drm_plane_type type;"
No idea how to deal with that, so I just fixed that up
by hand.
Also it thinks '...' is part of the semantic patch, so I put an
'int DOTDOTDOT' placeholder in its place and got rid of it with
sed afterwards.
I didn't convert drm_plane_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
typedef uint32_t;
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5, E6, E7;
@@
drm_universal_plane_init(E1, E2, E3, E4, E5, E6, E7
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NUL for no-name instead of ""
Leave drm_plane_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670795-2853-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
I didn't convert drm_crtc_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5;
@@
drm_crtc_init_with_planes(E1, E2, E3, E4, E5
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NULL for no-name instead of ""
Leave drm_crtc_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670771-2751-1-git-send-email-ville.syrjala@linux.intel.com
Drivers shouldn't clobber the passed in addfb ioctl parameters.
i915 was doing just that. To prevent it from happening again,
pass the struct around as const, starting all the way from
internal_framebuffer_create().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On atomic drivers we can dig out the primary plane rotation from the
plane state instead of looking at the legacy crtc->invert_dimensions
flag. The flag is not set by anyone except omapdrm, and it would be
racy to set it the same way in the atomic helpers.
v2: Kill crtc->invert_dimensions totally since omap is state based
already and no one else ever used it (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445009919-22746-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit 131e663bd6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 9 23:32:33 2015 +0200
drm/gem: rip out drm vma accounting for gem mmaps
there is no need for this any more.
v2: Fixup compile noise spotted by 0-day build.
Link: http://mid.gmane.org/1444894601-5200-9-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Just one special case (since i915 lost its ums code, yay):
- radeon: Has slots for the old ums ioctls which don't have
DRM_UNLOCKED, but all filled with drm_invalid_op. So ok to drop it
everywhere.
Every other kms driver just has DRM_UNLOCKED for all their ioctls, as
they should.
v2: admgpu happened, include that one too. And i915 lost its UMS
support which means we can change all the i915 ioctls too.
v3: Rebased on top of new vmwgfx DX interface extensions.
v4: Rebase on top of render-node support in exynos.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_count() returns the software counter. We should not pretend
it's the hw counter since we use the hw counter to figuere out what the
software counter value should be. So instead provide a new function
drm_vblank_no_hw_counter() for drivers that don't have a real hw
counter. The new function simply returns 0, which is about the only
thing it can do.
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
[danvet: s/int pipe/unsigned int pipe/ to follow Thierry's interface
change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid magic numbers and use the introduced defines.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With drivers supporting runtime pm it's generally not a good idea to
touch the hardware when it's off. Add an option to the commit_planes
helper to support this case.
Note that the helpers already add all planes on a crtc when a modeset
happens, hence plane updates will not be lost if drivers set this to
true.
v2: Check for NULL state->crtc before chasing the pointer. Also check
both old and new crtc if there's a switch. Finally just outright
disallow switching crtcs for a plane if the plane is in active use, on
most hardware that doesn't make sense.
v3: Since commit_planes(active_only = true) is for enabling things
only after all the crtc are on we should only look at the new crtc to
decide whether to call the plane hooks - if the current CRTC isn't on
then skip. If the old crtc (when moving a plane) went down then the
plane should have been disabled as part of the pipe shutdown work
already. For which there's currently no helper really unfortunately.
Also move the check for wether a plane gets a new CRTC assigned while
still in active use out of this patch.
v4: Rebase over exynos changes.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This removes the need to separately track fb changes i915.
That will be done as a separate commit, however.
Changes since v1:
- Add dri-devel to cc.
- Fix a check in intel's prepare and cleanup fb to take rotation
into account.
Changes since v2:
- Split out i915 changes to a separate commit.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
[danvet: Squash in msm fixup from Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Update error handling for new drm_fb_helper funcs. Check using IS_ERR()
instead of checking for NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
v2:
- No changes
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten didn't fully test his patches on all drm drivers and
apparently missed a few places when grepping.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
use mm.h definition
Cc: David Airlie <airlied@linux.ie>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
align_pitch() uses ALIGN() to ensure the pitch is aligned to SGX's
requirement of 8 pixels. However, ALIGN() expects the alignment value to
be a power of two, which is not the case for 24 bits per pixels.
Use roundup() instead, which works for all alignments.
This fixes the error seen with 24 bits per pixel modes:
"buffer pitch (2176 bytes) is not a multiple of pixel size (3 bytes)"
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If tiler_unpin() call in omap_gem_put_paddr() fails,
omap_gem_put_paddr() will immediately stop processing and return an
error.
This patch remoes that error checking, and also removes
omap_gem_put_paddr()'s return value, because:
* The caller of omap_gem_put_paddr() can do nothing if an error
happens, so it's pointless to return an error value
* If tiler_unpin() fails, the GEM object will possibly be left in an
undefined state, where the DMM mapping may have been removed, but the
GEM object still thinks everything is as it should be, leading to
crashes later.
* There's no point in returning an error from a "free" call, as the
caller can do nothing about it. So it's better to clean up as much as
possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_framebuffer_unpin() check the return value of omap_gem_put_paddr()
and return immediately if omap_gem_put_paddr() fails.
This patch removes the check for the return value, and also removes the
return value of omap_framebuffer_unpin(), because:
* Nothing checks the return value of omap_framebuffer_unpin(), and even
something did check it, there's nothing the caller can do to handle
the error.
* If a omap_gem_put_paddr() fails, the framebuffer's other planes will
be left unreleased. So it's better to call omap_gem_put_paddr() for
all the planes, even if one would fail.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The DMM driver uses a timeout of 1 ms to wait for DMM transaction to
finish. While DMM should always finish the operation within that time,
the timeout is rather strict. Small misbehavior of the system (e.g. an
irq taking too long) could trigger the timeout.
As the DMM is a critical piece of code for display memory management,
let's increase the timeout to 100 ms so that we are less likely to fail
a memory allocation in case of system misbehaviors. 100 ms is just a
guess of a reasonably large timeout. The HW should accomplish the task
in less than 1 ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRM allows planes to be partially off-screen, but DSS hardware does not.
This patch adds the necessary check to reject plane configs if the plane
is not fully inside the crtc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On a platform with no TILER (e.g. omap3, am43xx), when the user wants to
allocate buffer with flag OMAP_BO_SCANOUT, the buffer needs to be
allocated with dma_alloc_writecombine. For some reason the driver does
not return an error if that alloc fails, instead it continues without
backing memory. This leads to errors later when the user tries to use
the buffer.
This patch makes the driver return an error if dma_alloc_writecombine
fails.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Rework the crtc event/flip_wait system as follows:
- If we enable a crtc (full modeset), we set omap_crtc->pending and
register vblank irq.
- If we need to set GO bit (page flip), we do the same but also set the
GO bit.
- On vblank we unregister the irq, clear the 'pending' flag, send vblank
event to userspace if crtc->state->event != NULL, and wake up
'pending_wait' wq.
- In omap_atomic_complete() we wait for the 'pending' flag to get reset
for all enabled crtcs using 'pending_wait' wq.
The above ensures that we send the events to userspace in vblank, and
that after the wait in omap_atomic_complete() everything for the
affected crtcs has been completed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_crtc_atomic_flush() is the only user of omap_crtc_flush(), so just
move the code from omap_crtc_flush() to omap_crtc_atomic_flush().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Before atomic modesetting omap_framebuffer_pin() and
omap_framebuffer_unpin() were always called with modesetting locks
taken. With atomic modesetting support this is no longer the case, and
we need locking to protect the pin_count and the paddr, as multiple
threads may pin the same fb concurrently.
This patch adds a mutex to struct omap_framebuffer, and uses it in
omap_framebuffer_pin() and omap_framebuffer_unpin().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_plane_atomic_update() calls dispc_ovl_setup(), which can fail (but
shouldn't). To make the code a bit more robust, make sure the plane gets
disabled if dispc_ovl_setup() fails, as otherwise we might get illegal
HW configuration leading to error interrupts.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
At the moment we have omap_plane_setup() function which handles both
enabling (and configuring) and disabling the plane. With atomic
modesetting we have separate hooks for plane enable/config and disable.
This patch moves the code from omap_plane_setup() to
omap_plane_atomic_update() and omap_plane_atomic_disable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
With atomic modesetting, omap_plane_setup()'s return value is ignored as
the functions using it cannot fail. dispc_ovl_setup(), called by
omap_plane_setup(), can fail (but shouldn't).
Instead of returning an error from omap_plane_setup() which gets
ignored, return void and use WARN if dispc_ovl_setup() fails.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Planes setup is handled by the DRM core through the atomic helpers,
there's no need to duplicate the code in the CRTC .enable() and
.disable() operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_flush() call in omap_crtc_enable() and omap_crtc_disable()
is a no-op, as the display manager is always disabled at this point. Just
remove the function call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the driver is fully converted to atomic operations, and that
the atomic helpers call the operations in the right order, we can move
encoder setup to where it belongs, in the encoder operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of sprinkling dispc_runtime_get() and dispc_runtime_put() calls
in various CRTC operations, move all power management code to the atomic
commit function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_encoder_setup() function is always called with the DSS
enabled. Remove the dispc_runtime_get() and dispc_runtime_put() calls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRM page flip vblank events requested by page flips or atomic commits
are created by the DRM core and then passed to driver through CRTC
states (for atomic commit) or directly to the page flip handler (for
legacy page flips). The events are then kept aside until the page flip
completes, at which point drivers queue them for delivery with a call to
drm_send_vblank_event().
When a DRM file handle is closed events pending for delivery are cleaned
up automatically by the DRM core. Events that have been passed to the
driver but haven't completed yet, however, are not handled by the DRM
core. Drivers are responsible for destroying them and must not attempt
to queue them for delivery. This is usually handled by drivers'
preclose() handlers that cancel and destroy page flip events that
reference the file handle being closed.
With asynchronous atomic updates the story becomes more complex. Several
asynchronous atomic updates can be pending, each of them carrying
per-CRTC events. As the atomic_commit() operation doesn't receive a file
handle context, drivers can't know which file handle a pending update
refers to, making it difficult to cancel or wait for completion of
updates related to the file handle being closed.
It should be noted that cancelling page flips or waiting for atomic
updates completion isn't required by the DRM core when closing a file
handle. The only requirement is that no event gets queued for delivery
after the preclose() operation returns. This can easily be achieved by
storing events for atomic commits in a list, unlinking events from the
file handle being closed by setting the file_priv field to NULL, and
skipping delivery of unlinked events.
This logic replaces the page flip cancellation completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When performing asynchronous atomic updates the modeset lock isn't taken
around the callers of omap_crtc_flush(). This isn't an issue though, as
access to the CRTC is properly serialized. Just drop the warning.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_flush() function is always called with a reference to the
dispc held. Remove unnecessary calls to dispc_runtime_get() and
dispc_runtime_put().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function isn't used outside of its compilation unit, make it static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The field tracks the plane state to avoid double-enable or -disable.
This isn't required anymore, as
- the DRM atomic core guarantees that the plane atomic_update and
atomic_disable functions will never be called on an enabled/disabled
plane
- the CRTC enable/disable operations that enable/disable the plane are
already guarded against double enable/disable
We can thus remove the enabled field completely. The
omap_plane_set_enable() function then becomes a wrapper around
omap_plane_setup() which can be called directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The field tracks the CRTC state to avoid double-enable or -disable. As
the DRM atomic core guarantees that the CRTC enable and disable
functions won't be called on an already enabled or disabled CRTC, such
tracking isn't needed. Remove the enabled field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The crtc info structure is only used to setup the crtc through the DSS
API. Move it from the crtc structure to local variables in
omap_crtc_dss_enable().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Peter Ujfalusi