Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
'new_interfaces' should be freed to avoid memory leak.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a conflict with these files:
drivers/usb/early/ehci-dbgp.c
drivers/usb/host/ehci-ls1x.c
drivers/usb/host/ohci-xls.c
drivers/usb/musb/ux500.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old parameter "port" is useless for phy notify, as one usb
phy is only for one usb port. New parameter "speed" stands for
the device's speed which is on the port, this "speed" parameter
is needed at some platforms which will do some phy operations
according to device's speed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Mike Thompson <mpthompson@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At commit 925aa46ba9, Richard Zhao
<richard.zhao@freescale.com> adds the phy notification callback
when port change occurs. In fact, this phy notification should
be added according to below rules:
1. Only set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during high speed host mode.
2. Do not set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during the reset and speed negotiation period.
3. Do not set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during host suspend/resume sequence.
Please refer: i.mx23RM(page: 413) for below rules.
http://www.freescale.com/files/dsp/doc/ref_manual/IMX23RM.pdf
Freescale i.MX SoC, i.mx23, i.mx28 and i.mx6(i.mx6SL does not
need to follow the 3rd rule) need to follow above rules.
Current code set connect notification (HW_USBPHY_CTRL.ENHOSTDISCONDETECT)
at hub_port_connect_change, it conflicts with above the 2th rule.
The correct notification setting method should be:
1. Set connect notify after the second bus reset.
2. Set disconnect notify after disconnection.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Mike Thompson <mpthompson@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like I've run into some inconsistency in the USB stack behavior.
The USB stack maintains, among others, two states for the attach
USB device: authorized and owned. Authorization state is accessible to
the user space code through correspondent sysfs files, the ownership
can be set by claiming the hub's port with ioctl call. Both state may
be set before the device is attached, by access the hub settings. When
the new device is attached, both authorization and ownership prevent
the kernel USB stack from setting the newly attached device
configuration, but when the device is authorized, the ownership state
is ignored. It looks like ignoring the ownership state on
authorization make the stack behavior inconsistent; it also prevents
the user space code from completely overriding configuration
selection, important for implementing workarounds for bugs in the
device configuration selection.
The following patch makes the stack behavior more consistent, by
moving ownership test into usb_choose_configuration - the later
function is used both by generic_probe and usb_authorize_device
Signed-off-by: Joseph Hindin <hindin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 73d4066055.
Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled. Thomas pointed out that this patch
is incorrect, and can cause problems. So revert it to get the
previously working functionality back.
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1633) changes slightly the way usbcore handled
submissions of URBs that are already active. It will now return
-EBUSY rather than -EINVAL, and it will call WARN_ONCE to draw
people's attention to the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1631) fixes a bug that shows up when a config change
fails for a device under an xHCI controller. The controller needs to
be told to disable the endpoints that have been enabled for the new
config. The existing code does this, but before storing the
information about which endpoints were enabled! As a result, any
second attempt to install the new config is doomed to fail because
xhci-hcd will refuse to enable an endpoint that is already enabled.
The patch optimistically initializes the new endpoints' device
structures before asking the device to switch to the new config. If
the request fails then the endpoint information is already stored, so
we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no
trouble. The rest of the error path is slightly more complex now; we
have to disable the new interfaces and call put_device() rather than
simply deallocating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Matthias Schniedermeyer <ms@citd.de>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1621) removes the limit on the number of loops allowed
in hub_tt_work(). The value is arbitrary, and it's silly to have a
limit in the first place -- anything beyond the limit would not get
handled.
Besides, it's most unlikely that we'll ever need to clear more than a
couple of TT buffers at any time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in all of the USB changes in 3.7-rc3 into usb-next and
resolves the merge issue with:
drivers/usb/misc/ezusb.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets hub device's default autosuspend delay as 0 to
speedup bus suspend, see comments in code for details.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub status endpoint has a long 'bInterval', which is 255ms
for FS/LS device and 256ms for HS device according to USB 2.0 spec,
so the device connection change may be reported later more than 255ms
via status pipe.
The connection change in hub may have been happened already on the
downstream ports, but no status URB completes when it is killed
in hub_suspend(auto), so the connection change may be missed by some
buggy hub devices, which won't generate remote wakeup signal after
their remote wakeup is enabled and they are put into suspend state.
The problem can be observed at least on the below Genesys Logic, Inc.
hub devices:
0x05e3,0x0606
0x05e3,0x0608
In theory, there is no way to fix the problem completely, but we
can make it less likely to occur by this patch.
This patch introduces one quirk of HUB_QUIRK_CHECK_PORTS_AUTOSUSPEND
to check ports' change during hub_suspend(auto) for the buggy
devices. If ports' change is found, terminate the auto suspend and
return to working state.
So for the buggy hubs, if the connection change happend before
the ports' check, it can be handled correctly. If it happens between
the ports' check and enabling remote wakeup/entering suspend, it
will be missed. Considered the interval is quite short, it is very
less likely to happen during the window.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1620) speeds up USB root-hub resumes in the common case
where every enabled port has its suspend feature set (which currently
will be true for every runtime resume of the root hub). If all the
enabled ports are suspended then resuming the root hub won't resume
any of the downstream devices. In this case there's no need for a
Resume Recovery delay, because that delay is meant to give devices a
chance to get ready for active use.
To keep track of the port suspend features, the patch adds a
"port_is_suspended" flag to struct usb_device. This has to be tracked
separately from the device's state; it's entirely possible for a USB-2
device to be suspended while the suspend feature on its parent port is
clear. The reason is that devices will go into suspend whenever their
parent hub does.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1619) improves the interface to the "hub_for_each_child"
macro. The name clearly suggests that the macro iterates over child
devices; it does not suggest that the loop will also iterate over
unnconnected ports.
The patch changes the macro so that it will skip over unconnected
ports and iterate only the actual child devices. The two existing
call sites are updated to avoid testing for a NULL child pointer,
which is now unnecessary.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We defined bus_to_hdc for that, use it.
Signed-off-by: Yuanhan Liu <yliu.null@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flush_work_sync and flush_work are now the same and flush_work_sync
has been deprecated. This fixes the following warning:
drivers/usb/core/hub.c: In function hub_quiesce:
drivers/usb/core/hub.c:1216:3: warning: flush_work_sync is deprecated (declared at include/linux/workqueue.h:448) [-Wdeprecated-declarations]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1611) updates the USB documentation and kerneldoc to
give a more precise meaning for the URB_ISO_ASAP flag and to explain
more of the details of scheduling for isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handling of large output bulk transfers is broken; the same user
page is read over and over again. Fixed with this patch.
Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's four fixes for the USB 3.0 Link Power Management code. They
work around some USB 3.0 devices that don't support LPM, like the
Western Digital My Passport hard drive. They also fix an LPM disable
ref count bug that would cause LPM to remain disabled for a device
after a failed probe.
Please queue for 3.7 after the merge window closes. Several patches are
marked for stable.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=n/bA
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
USB 3.0 Link PM fixes.
Hi Greg,
Here's four fixes for the USB 3.0 Link Power Management code. They
work around some USB 3.0 devices that don't support LPM, like the
Western Digital My Passport hard drive. They also fix an LPM disable
ref count bug that would cause LPM to remain disabled for a device
after a failed probe.
Please queue for 3.7 after the merge window closes. Several patches are
marked for stable.
Sarah Sharp
SEL and PEL are in microseconds, not milliseconds. Also, fix a split
string that will trigger checkpatch warnings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The Set SEL control transfer tells a device the exit latencies
associated with a device-initated U1 or U2 exit. Since a parent hub may
initiate a transition to U1 soon after a downstream port's U1 timeout is
set, we need to make sure the device receives the Set SEL transfer
before the parent hub timeout is set.
This patch should be backported to kernels as old as 3.5, that contain
the commit 1ea7e0e8e3 "USB: Add support to
enable/disable USB3 link states."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Some USB 3.0 devices signal that they don't implement Link PM by having
all zeroes in the U1/U2 exit latencies in their SuperSpeed BOS
descriptor. Don found that a Western Digital device he has experiences
transfer errors when LPM is enabled. The lsusb shows the U1/U2 exit
latencies are set to zero:
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 0 micro seconds
bU2DevExitLat 0 micro seconds
The fix is to not enable LPM for a particular link state if we find its
corresponding exit latency is zero.
This patch should be backported to kernels as old as 3.5, that contain
the commit 1ea7e0e8e3 "USB: Add support to
enable/disable USB3 link states."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Don Zickus <dzickus@redhat.com>
Cc: stable@vger.kernel.org
Before a driver is probed, we want to disable USB 3.0 Link Power
Management (LPM), in case the driver needs hub-initiated LPM disabled.
After the probe finishes, we want to attempt to re-enable LPM, order to
balance the LPM ref count.
When a probe fails (such as when libusual doesn't want to bind to a USB
3.0 mass storage device), make sure to balance the LPM ref counts by
re-enabling LPM.
This patch should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Pul ACPI & Power Management updates from Len Brown:
- acpidump utility added
- intel_idle driver now supports IVB Xeon
- turbostat utility can now count SMIs
- ACPI can now bind to USB3 hubs
- misc fixes
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (49 commits)
ACPI: Add new sysfs interface to export device description
ACPI: Harden acpi_table_parse_entries() against BIOS bug
tools/power/turbostat: add option to count SMIs, re-name some options
tools/power turbostat: add [-d MSR#][-D MSR#] options to print counter deltas
intel_idle: enable IVB Xeon support
tools/power turbostat: add [-m MSR#] option
tools/power turbostat: make -M output pretty
tools/power turbostat: print more turbo-limit information
tools/power turbostat: delete unused line
tools/power turbostat: run on IVB Xeon
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
ACPI: run _OSC after ACPI_FULL_INITIALIZATION
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
tools/power/acpi/acpidump: version 20071116
tools/power/acpi/acpidump: version 20070714
tools/power/acpi/acpidump: version 20060606
tools/power/acpi/acpidump: version 20051111
xo15-ebook: convert to module_acpi_driver()
...
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ca9c9d0c92.
Rafael wants more time to work on the user api to handle port power
issues, so let's just revert the sysfs changes for now.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_get_physical_device_location()'s 2nd argument has been changed
in ACPI implementaion, so need a follow-on change in
usb_acpi_check_pld().
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Neil Zhang <zhangwm@marvell.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
retval is 0, and carefully assigned - and tested as non zero.
This is not useful. While we are at it remove some other bogus initialisation
in the function
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not needed, and commented out, so just remove it.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ff823c79a5 ("usb: move children
to struct usb_port") forgot to consider the hub_disconnect sequence,
which releases ports before quiescing the hub, which will lead to a
use-after-free, since hub_quiesce() will try to disconnect ports'
children, which are already deallocated. Simple modprobe dummy_hcd &&
rmmod dummy_hcd will illustrate the problem.
This patch moves deallocation of hub's ports after hub_quiesce() call
in hub_disconnect().
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the IRQF_DISABLED as the flag is now a NOOP and has been
deprecated and in hardirq context the interrupt is disabled.
so in usb/host code:
Removing the usage of flag IRQF_DISABLED;
Removing the calling local_irq save/restore actions in irq
handler usb_hcd_irq();
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds two sysfs files for each usb hub port to allow userspace
to control the port power policy.
For an upcoming Intel xHCI roothub, this will translate into ACPI calls
to completely power off or power on the port. As a reminder, when these
ports are completely powered off, the USB host and device will see a
physical disconnect. All future USB device connections will be lost,
and the device will not be able to signal a remote wakeup.
The control sysfs file can be written to with two options:
"on" - port power must be on.
"off" - port must be off.
The state sysfs file reports usb port's power state:
"on" - powered on
"off" - powered off
"error" - can't get power state
For now, let userspace dictate the port power off policy. Future
patches may add an in-kernel policy.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern pointed out that a USB port could potentially get powered off
when the attached USB device is in the middle of enumerating, due to
race conditions:
http://marc.info/?l=linux-usb&m=134130616707548&w=2
If that happens, we need to ensure the enumeration fails. If a call to
usb_get_descriptor() fails for a reason other than a Stall, return an
error. That should handle the case where the port is powered off.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upcoming Intel systems will have an ACPI method to control whether a USB
port can be completely powered off. The implication of powering off a
USB port is that the device and host sees a physical disconnect, and
subsequent port connections and remote wakeups will be lost.
Add a new function, usb_acpi_power_manageable(), that can be used to
find whether the usb port has ACPI power resources that can be used to
power on and off the port on these machines. Also add a new function
called usb_acpi_set_power_state() that controls the port power via these
ACPI methods.
When the USB core calls into the xHCI hub driver to power off a port,
check whether the port can be completely powered off via this new ACPI
mechanism. If so, call into these new ACPI methods. Also use the ACPI
methods when the USB core asks to power on a port.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the upcoming USB port power off patches, we need to know whether a
USB port can ever see a disconnect event. Often USB ports are internal
to a system, and users can't disconnect USB devices from that port.
Sometimes those ports will remain empty, because the OEM chose not to
connect an internal USB device to that port.
According to ACPI Spec 9.13, PLD indicates whether USB port is
user visible and _UPC indicates whether a USB device can be connected to
the USB port (we'll call this "connectible"). Here's a matrix of the
possible combinations:
Visible Connectible
Name Example
-------------------------------------------------------------------------
Yes No Unknown (Invalid state.)
Yes Yes Hot-plug USB ports on the outside of a laptop.
A user could freely connect and disconnect
USB devices.
No Yes Hard-wired A USB modem hard-wired to a port on the
inside of a laptop.
No No Not used The port is internal to the system and
will remain empty.
Represent each of these four states with an enum usb_port_connect_type.
The four states are USB_PORT_CONNECT_TYPE_UNKNOWN,
USB_PORT_CONNECT_TYPE_HOT_PLUG, USB_PORT_CONNECT_TYPE_HARD_WIRED, and
USB_PORT_NOT_USED. When we get the USB port's acpi_handle, store the
state in connect_type in struct usb_port.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ACPI DSDT table, only usb root hub and usb ports are ACPI device
nodes. Originally, we bound the usb port's ACPI node to the usb device
attached to the port. However, we want to access those ACPI port
methods when the port is empty, and there's no usb_device associated
with that port.
Now that the usb port is a real device, we can bind the port's ACPI node
to struct usb_port instead.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_device structure contains an array of usb_device "children".
This array is only valid if the usb_device is a hub, so it makes no
sense to store it there. Instead, store the usb_device child
in its parent usb_port structure.
Since usb_port is an internal USB core structure, add a new function to
get the USB device child, usb_hub_find_child(). Add a new macro,
usb_hub_get_each_child(), to iterate over all the children attached to a
particular USB hub.
Remove the printing the USB children array pointer from the usb-ip
driver, since it's really not necessary.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch turns each USB port on a hub into a new struct device. This
new device has the USB hub interface device as its parent. The port
devices are stored in a new structure (usb_port), and an array of
usb_ports are dynamically allocated once we know how many ports the USB
hub has.
Move the port_owner variable out of usb_hub and into this new structure.
A new file will be created in the hub interface sysfs directory, so
add documentation.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel's version number is used as decimal in the bcdDevice field of
the RH descriptor. For kernel version v3.12 we would see 3.0c in lsusb.
I am not sure how important it is to stick with bcd values since this is
this way since we started git history and nobody complained (however back
then we reported only 2.6).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apps which deal with devices which also have a kernel driver, need to do
the following:
1) Check which driver is attached, so as to not detach the wrong driver
(ie detaching usbfs while another instance of the app is using the device)
2) Detach the kernel driver
3) Claim the interface
Where moving from one step to the next for both 1-2 and 2-3 consists of
a (small) race window. So currently such apps are racy and people just live
with it.
This patch adds a new ioctl which makes it possible for apps to do this
in a race free manner. For flexibility apps can choose to:
1) Specify the driver to disconnect
2) Specify to disconnect any driver except for the one named by the app
3) Disconnect any driver
Note that if there is no driver attached, the ioctl will just act like the
regular claim-interface ioctl, this is by design, as returning an error for
this condition would open a new bag of race-conditions.
Changes in v2:
-Fix indentation of if blocks where the condition spans multiple lines
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds