Commit Graph

308 Commits

Author SHA1 Message Date
Yevgeny Petrilin 04714a16db mlx4_en: updated driver version
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 15:00:42 -07:00
Yevgeny Petrilin fa37a9586f mlx4_en: Moving to work with GRO
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 15:00:42 -07:00
Yevgeny Petrilin 0533943c5c mlx4_en: UDP RSS support
Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:57:09 -07:00
Yevgeny Petrilin d7e1a487d3 mlx4_en: reconfiguring mac address.
When Mac address is removed from one port of the CX2 device, the other device
should reconfigure its Mac.
This fixes an issue with failover, when both ports have the same Mac address,
and one of the ports, is closed, the second one stops receiving traffic.
(bugzilla #1965 at bugs.openfabrics.org)

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:53 -07:00
Yevgeny Petrilin bc081cecf3 mlx4_en: get/set ringsize uses actual ring size
In case that the rings were not fully filled, the report in Ethtool
should be according to the actual size that was filled.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:52 -07:00
Yevgeny Petrilin 7699517db4 mlx4_en: Fixing report in Ethtool get_settings
The report now based on query from FW, giving the correct tranciever type
and link speed.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:51 -07:00
Yevgeny Petrilin e7c1c2c462 mlx4_en: Added self diagnostics test implementation
The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
   on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:51 -07:00
Yevgeny Petrilin 3005ad40b9 mlx4_en: Validate port up prior to transmitting
We might try to use resources which were not activated.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:50 -07:00
Yevgeny Petrilin e5cc44b2eb mlx4_en: Reporting link state with KERN_INFO
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:49 -07:00
Yevgeny Petrilin a0b4e6e09c mlx4_en: Fixed MAX_TX_RINGS definition
Defined as sum of default number of TX rings and number of
rings used for priority flow control mode.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:49 -07:00
Yevgeny Petrilin 7c2873809d mlx4_en: performing CLOSE_PORT at the end of tear-down process
All port's resources should be closed before we give the
CLOSE_PORT command to the firmware.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:48 -07:00
Yevgeny Petrilin 8bf2e58f8b mlx4_en: Setting dev->perm_addr field
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:48 -07:00
Yevgeny Petrilin 00d7d7bc6e mlx4_en: Setting actual RX ring size
When configuring HW resources, the RX ring size that is passed should be the actual
size that depends on number of buffers that we succeeded to allocate.
The mask for ring size should also be configured accordingly

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:47 -07:00
Yevgeny Petrilin 69351a2933 mlx4_en: Fixed incorrect unmapping on RX flow.
When allocating new fragments to replace the ones that would be passed to the stack,
The fragments that should be replaced, are the ones that were already used.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24 14:54:47 -07:00
Amerigo Wang f3c58aceaa mlx4: remove num_lro parameter
As suggested by David, this parameter can die, we can use ethtool
to turn LRO on/off. Compile tests only.

Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-22 21:43:58 -07:00
Joe Perches baeb2ffab4 drivers/net: Convert unbounded kzalloc calls to kcalloc
These changes may be slightly safer in some instances.

There are other kzalloc calls with a multiply, but those
calls are typically "small fixed #" * sizeof(some pointer)"
and those are not converted.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-17 17:45:14 -07:00
Joe Perches 0a645e8097 drivers/net/mlx4: Use %pV, pr_<level>, printk_once
Remove near duplication of format string constants by using the newly
introduced vsprintf extention %pV to reduce text by 20k or so.

$ size drivers/net/mlx4/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 161367	   1866	  48784	 212017	  33c31	drivers/net/mlx4/built-in.o
 142621	   1866	  46248	 190735	  2e90f	drivers/net/mlx4/built-in.o.new

Use printk_once as appropriate.
Convert printks to pr_<level>, some bare printks now use pr_cont.
Remove now unused #define PFX.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-15 19:05:17 -07:00
Amerigo Wang d2ef859034 mlx4: add dynamic LRO disable support
This patch adds dynamic LRO diable support for mlx4 net driver.
It also fixes a bug of mlx4, which checks NETIF_F_LRO flag in rx
path without rtnl lock.

(I don't have mlx4 card, so only did compiling test. Anyone who wants
to test this is more than welcome.)

This is based on Neil's initial work too, and heavily modified based
on Stanislaw's suggestions.

Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Neil Horman <nhorman@redhat.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-28 23:04:10 -07:00
Eric Dumazet ba2d358791 drivers/net: use __packed annotation
cleanup patch.

Use new __packed annotation in drivers/net/

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03 03:18:23 -07:00
Eli Cohen 741a00be1f mlx4_en: use net_device dev_id to indicate port number
Today, there are no means to know which port of a hardware device a netdev
interface uses. struct net_device conatins a field, dev_id, that can be used
for that. Use this field to save the port number in ConnectX that is being used
by the net device; port numbers are zero based.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-31 00:27:45 -07:00
Linus Torvalds 8e9815a0f8 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/nes: Fix incorrect unlock in nes_process_mac_intr()
  RDMA/nes: Async event for closed QP causes crash
  RDMA/nes: Have ethtool read hardware registers for rx/tx stats
  RDMA/cxgb4: Only insert sq qid in lookup table
  RDMA/cxgb4: Support IB_WR_READ_WITH_INV opcode
  RDMA/cxgb4: Set fence flag for inv-local-stag work requests
  RDMA/cxgb4: Update some HW limits
  RDMA/cxgb4: Don't limit fastreg page list depth
  RDMA/cxgb4: Return proper errors in fastreg mr/pbl allocation
  RDMA/cxgb4: Fix overflow bug in CQ arm
  RDMA/cxgb4: Optimize CQ overflow detection
  RDMA/cxgb4: CQ size must be IQ size - 2
  RDMA/cxgb4: Register RDMA provider based on LLD state_change events
  RDMA/cxgb4: Detach from the LLD after unregistering RDMA device
  IB/ipath: Remove support for QLogic PCIe QLE devices
  IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters
  IB/mad: Make needlessly global mad_sendq_size/mad_recvq_size static
  IB/core: Allow device-specific per-port sysfs files
  mlx4_core: Clean up mlx4_alloc_icm() a bit
  mlx4_core: Fix possible chunk sg list overflow in mlx4_alloc_icm()
2010-05-25 12:05:17 -07:00
Thomas Gleixner 3142788b79 drivers/base: Convert dev->sem to mutex
The semaphore is semantically a mutex. Convert it to a real mutex and
fix up a few places where code was relying on semaphore.h to be included
by device.h, as well as the users of the trylock function, as that value
is now reversed.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:37:30 -07:00
Roland Dreier c050def076 mlx4_core: Clean up mlx4_alloc_icm() a bit
Handle the allocation error case first, so that we don't have further
nested if for handling the common case of success.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-05-20 15:58:22 -07:00
Sebastien Dugue c0dc72bad9 mlx4_core: Fix possible chunk sg list overflow in mlx4_alloc_icm()
If the number of sg entries in the ICM chunk reaches MLX4_ICM_CHUNK_LEN,
we must set chunk to NULL even for coherent mappings so that the next
time through the loop will allocate another chunk.  Otherwise we'll
overflow the sg list the next time through the loop.  This will lead to
memory corruption if this case is hit.

mthca does not have this bug.

Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-05-20 15:58:22 -07:00
Joe Perches ee289b6440 drivers/net: remove useless semicolons
switch and while statements don't need semicolons at end of statement

[ Fixup minor conflicts with recent wimax merge... -DaveM ]

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17 22:47:34 -07:00
Joe Perches a4b770972b drivers/net: Remove unnecessary returns from void function()s
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

It also does not remove null void functions with return.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

with some cleanups by hand.

Compile tested x86 allmodconfig only.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14 00:19:28 -07:00
David S. Miller 871039f02f Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/stmmac/stmmac_main.c
	drivers/net/wireless/wl12xx/wl1271_cmd.c
	drivers/net/wireless/wl12xx/wl1271_main.c
	drivers/net/wireless/wl12xx/wl1271_spi.c
	net/core/ethtool.c
	net/mac80211/scan.c
2010-04-11 14:53:53 -07:00
David S. Miller 4a35ecf8bf Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bonding/bond_main.c
	drivers/net/via-velocity.c
	drivers/net/wireless/iwlwifi/iwl-agn.c
2010-04-06 23:53:30 -07:00
Jiri Pirko 22bedad3ce net: convert multicast list to list_head
Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:15 -07:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Frans Pop 2381a55c88 net/various: remove trailing space in messages
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-24 14:10:38 -07:00
Greg Kroah-Hartman 3691c964fa sysfs: fix sysfs lockdep warning in mlx4 code
This fixes a sysfs lockdep warning in the mlx4 code.

Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19 07:12:15 -07:00
Jiri Pirko ff6e2163f2 net: convert multiple drivers to use netdev_for_each_mc_addr, part7
In mlx4, using char * to store mc address in private structure instead.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-16 21:23:25 -07:00
FUJITA Tomonori e4fc85600b mlx4: replace the dma_sync_single_range_for_cpu/device API
There are only two users of the dma_sync_single_range_for_cpu/device
API in mainline (mlx4 and ssb). The
dma_sync_single_range_for_cpu/device API has never been documented and
the dma_sync_single_for_cpu/device API also support a partial sync.

This converts mlx4 to use the dma_sync_single_for_cpu/device API
(preparations for the removal of the dma_sync_single_range_for_cpu/device API).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-19 13:19:51 -08:00
David S. Miller 51c24aaaca Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-01-23 00:31:06 -08:00
Alexey Dobriyan a3aa18842a drivers/net/: use DEFINE_PCI_DEVICE_TABLE()
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07 23:54:26 -08:00
Eli Cohen b4f77264cd mlx4_core: Fix cleanup in __mlx4_init_one() error path
If mlx4_init_port_info() fails, cleanup the initialized ports only.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-01-06 12:54:39 -08:00
Linus Torvalds 59be2e04e5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
  net: sh_eth alignment fix for sh7724 using NET_IP_ALIGN V2
  ixgbe: allow tx of pre-formatted vlan tagged packets
  ixgbe: Fix 82598 premature copper PHY link indicatation
  ixgbe: Fix tx_restart_queue/non_eop_desc statistics counters
  bcm63xx_enet: fix compilation failure after get_stats_count removal
  packet: dont call sleeping functions while holding rcu_read_lock()
  tcp: Revert per-route SACK/DSACK/TIMESTAMP changes.
  ipvs: zero usvc and udest
  netfilter: fix crashes in bridge netfilter caused by fragment jumps
  ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery
  sky2: leave PCI config space writeable
  sky2: print Optima chip name
  x25: Update maintainer.
  ipvs: fix synchronization on connection close
  netfilter: xtables: document minimal required version
  drivers/net/bonding/: : use pr_fmt
  can: CAN_MCP251X should depend on HAS_DMA
  drivers/net/usb: Correct code taking the size of a pointer
  drivers/net/cpmac.c: Correct code taking the size of a pointer
  drivers/net/sfc: Correct code taking the size of a pointer
  ...
2009-12-16 10:33:18 -08:00
Linus Torvalds e69381b417 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (45 commits)
  RDMA/cxgb3: Fix error paths in post_send and post_recv
  RDMA/nes: Fix stale ARP issue
  RDMA/nes: FIN during MPA startup causes timeout
  RDMA/nes: Free kmap() resources
  RDMA/nes: Check for zero STag
  RDMA/nes: Fix Xansation test crash on cm_node ref_count
  RDMA/nes: Abnormal listener exit causes loopback node crash
  RDMA/nes: Fix crash in nes_accept()
  RDMA/nes: Resource not freed for REJECTed connections
  RDMA/nes: MPA request/response error checking
  RDMA/nes: Fix query of ORD values
  RDMA/nes: Fix MAX_CM_BUFFER define
  RDMA/nes: Pass correct size to ioremap_nocache()
  RDMA/nes: Update copyright and branding string
  RDMA/nes: Add max_cqe check to nes_create_cq()
  RDMA/nes: Clean up struct nes_qp
  RDMA/nes: Implement IB_SIGNAL_ALL_WR as an iWARP extension
  RDMA/nes: Add additional SFP+ PHY uC status check and PHY reset
  RDMA/nes: Correct fast memory registration implementation
  IB/ehca: Fix error paths in post_send and post_recv
  ...
2009-12-16 10:32:31 -08:00
Akinobu Mita 43ff8b6085 mlx4: use bitmap_find_next_zero_area
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Roland Dreier <rolandd@cisco.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-16 07:20:19 -08:00
roel kluin e0802793f6 mlx4_core: return a negative error value
The return value should be negative.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-13 19:47:42 -08:00
André Goddard Rosa af901ca181 tree-wide: fix assorted typos all over the place
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:55 +01:00
Yevgeny Petrilin be504b0b9f mlx4_core: Fix parsing of reserved EQ cap
Value returned by firmware is the actual value, not a log.

Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-11-12 15:51:16 -08:00
Eli Cohen 417608c20a IB/mlx4: Remove limitation on LSO header size
Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary.  This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size.  The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length.  Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-11-12 11:19:44 -08:00
Eli Cohen 06c3aa5ef1 mlx4_core: Add a new supported 40 GigE device ID
Add MT26438 (ConnectX EN 40GigE PCIe 2.0 5GT/s) to the list of supported
devices.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-10-14 10:52:40 -07:00
Yevgeny Petrilin e76d0b67d0 mlx4_core: Add 40GigE device ID
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-10-07 15:46:49 -07:00
Linus Torvalds d7757be133 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Don't turn on carrier for a non-active port
  IB/mthca: Fix access to freed memory in catastrophic event handling
  mlx4_core: Pass cache line size to device FW
  RDMA/nes: Remove duplicate .ndo_set_mac_address field initialization
  IB/mad: Fix lock-lock-timer deadlock in RMPP code
2009-09-24 17:06:01 -07:00
Eli Cohen c57e20dcff mlx4_core: Pass cache line size to device FW
ConnectX can work more efficiently if the CPU cache line size is passed
to it with the INIT_HCA firmware command.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-24 11:03:03 -07:00
Vitaliy Gusev 634354d753 mlx4: Fix access to freed memory
catas_reset() uses pointer to mlx4_priv, but mlx4_priv is not valid
after call mlx4_restart_one().

Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-16 00:00:21 -07:00
Linus Torvalds d7e9660ad9 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
  netxen: update copyright
  netxen: fix tx timeout recovery
  netxen: fix file firmware leak
  netxen: improve pci memory access
  netxen: change firmware write size
  tg3: Fix return ring size breakage
  netxen: build fix for INET=n
  cdc-phonet: autoconfigure Phonet address
  Phonet: back-end for autoconfigured addresses
  Phonet: fix netlink address dump error handling
  ipv6: Add IFA_F_DADFAILED flag
  net: Add DEVTYPE support for Ethernet based devices
  mv643xx_eth.c: remove unused txq_set_wrr()
  ucc_geth: Fix hangs after switching from full to half duplex
  ucc_geth: Rearrange some code to avoid forward declarations
  phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
  drivers/net/phy: introduce missing kfree
  drivers/net/wan: introduce missing kfree
  net: force bridge module(s) to be GPL
  Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
  ...

Fixed up trivial conflicts:

 - arch/x86/include/asm/socket.h

   converted to <asm-generic/socket.h> in the x86 tree.  The generic
   header has the same new #define's, so that works out fine.

 - drivers/net/tun.c

   fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
   switched over to using 'tun->socket.sk' instead of the redundantly
   available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
   to the TUN driver") which added a new 'tun->sk' use.

   Noted in 'next' by Stephen Rothwell.
2009-09-14 10:37:28 -07:00
Arputham Benjamin f5f5951c74 mlx4_core: Distinguish multiple devices in /proc/interrupts
When the mlx4 driver uses the same name for interrupts for every
device in the system.  This can make it very confusing trying to work
out exactly which device MSI-X interrupts are for.  Change the driver
to add the PCI name of the device to the interrupt name.

Signed-off-by: Arputham Benjamin <abenjamin@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-05 20:24:50 -07:00
Yevgeny Petrilin 1af92e2a21 mlx4_core: Avoid double free_icms
On the error path of mlx4_init_hca(), mlx4_close_hca() is called,
followed by mlx4_free_icms() and mlx4_UNMAP_FA().  But both those
functions are also called from mlx4_close_hca(), which leads to a
double free.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-05 20:24:49 -07:00
Roland Dreier fa0681d212 mlx4_core: Allocate and map sufficient ICM memory for EQ context
The current implementation allocates a single host page for EQ context
memory, which was OK when we only allocated a few EQs.  However, since
we now allocate an EQ for each CPU core, this patch removes the
hard-coded limit (which we exceed with 4 KB pages and 128 byte EQ
context entries with 32 CPUs) and uses the same ICM table code as all
other context tables, which ends up simplifying the code quite a bit
while fixing the problem.

This problem was actually hit in practice on a dual-socket Nehalem box
with 16 real hardware threads and sufficiently odd ACPI tables that it
shows on boot

    SMP: Allowing 32 CPUs, 16 hotplug CPUs

so num_possible_cpus() ends up 32, and mlx4 ends up creating 33 MSI-X
interrupts and 33 EQs.  This mlx4 bug means that mlx4 can't even
initialize at all on this quite mainstream system.

Cc: <stable@kernel.org>
Reported-by: Eli Cohen <eli@mellanox.co.il>
Tested-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-05 20:24:49 -07:00
Roland Dreier ff149b2a16 mlx4_core: Remove unnecessary includes of <linux/init.h>
Lots of mlx4 files with no function annotations included <linux/init.h>
for no reason.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-05 20:24:49 -07:00
Roland Dreier a01df0fe5e mlx4_core: Use pci_request_regions()
The old code used two calls to pci_request_region() to get the two BARs
for the mlx4 device, for no particularly good reason.  Clean up the code
a little by converting this to a single call to pci_request_regions().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-05 20:24:48 -07:00
David S. Miller 6cdee2f96a Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/yellowfin.c
2009-09-02 00:32:56 -07:00
Stephen Hemminger 61357325f3 netdev: convert bulk of drivers to netdev_tx_t
In a couple of cases collapse some extra code like:
   int retval = NETDEV_TX_OK;
   ...
   return retval;
into
   return NETDEV_TX_OK;

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:14:07 -07:00
Dongdong Deng 4871953c0e drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of "A functions set" in the NETPOLL API
callbacks causes the interrupts to get enabled and can lead to kernel
instability.

The solution is to use "B functions set" to prevent the irqs from
getting enabled while in netpoll_send_skb().

A functions set:
local_irq_disable()/local_irq_enable()
spin_lock_irq()/spin_unlock_irq()
spin_trylock_irq()/spin_unlock_irq()

B functions set:
local_irq_save()/local_irq_restore()
spin_lock_irqsave()/spin_unlock_irqrestore()
spin_trylock_irqsave()/spin_unlock_irqrestore()

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23 19:51:03 -07:00
David S. Miller aa11d958d1 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	arch/microblaze/include/asm/socket.h
2009-08-12 17:44:53 -07:00
roel kluin 973507cb86 mlx4_en: Fix read buffer overflow in mlx4_en_complete_rx_desc()
If the length is less or equal to frag_prefix_size in the first iteration
we write skb_frags_rx[-1] and read from priv->frag_info[-1]

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-09 21:47:01 -07:00
Yevgeny Petrilin 9f519f68cf mlx4_en: Not using Shared Receive Queues
We use 1:1 mapping between QPs and SRQs on receive side,
so additional indirection level not required. Allocated the receive
buffers for the RSS QPs.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-06 19:28:18 -07:00
Yevgeny Petrilin b6b912e080 mlx4_en: Using real number of rings as RSS map size
There is no point in using more QPs then actual number of receive rings.
If the RSS function for two streams gives the same result modulo number
of rings, they will arrive to the same RX ring anyway.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-06 19:27:51 -07:00
Yevgeny Petrilin a35ee541a6 mlx4_en: Adaptive moderation policy change
If the net device is identified as "sender" (number of sent packets
is higher then the number of received packets and the incoming packets are
small), set the moderation time to its low limit.
We do it because the incoming packets are acks, and we don't want to delay them

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-06 19:27:28 -07:00
Linus Torvalds ae83060026 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
  ehea: Fix napi list corruption on ifconfig down
  igbvf: Allow VF driver to correctly recognize failure to set mac
  3c59x: Fix build failure with gcc 3.2
  sky2: Avoid transmits during sky2_down()
  iwlagn: do not send key clear commands when rfkill enabled
  libertas: Read buffer overflow
  drivers/net/wireless: introduce missing kfree
  drivers/net/wireless/iwlwifi: introduce missing kfree
  zd1211rw: fix unaligned access in zd_mac_rx
  cfg80211: fix regression on beacon world roaming feature
  cfg80211: add two missing NULL pointer checks
  ixgbe: Patch to modify 82598 PCIe completion timeout values
  bluetooth: rfcomm_init bug fix
  mlx4_en: Fix double pci unmapping.
  mISDN: Fix handling of receive buffer size in L1oIP
  pcnet32: VLB support fixes
  pcnet32: remove superfluous NULL pointer check in pcnet32_probe1()
  net: restore the original spinlock to protect unicast list
  netxen: fix coherent dma mask setting
  mISDN: Read buffer overflow
  ...
2009-08-04 15:38:34 -07:00
Yevgeny Petrilin eb4ad82641 mlx4_en: Fix double pci unmapping.
In cases of fragmented skb, with the data pointers being wrapped around
the TX buffer, the completion handling code would not forward the data
pointer and the firs fragment was unmapped several times, while others
were not unmapped at all.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-02 20:22:18 -07:00
David S. Miller 74d154189d Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/iwmc3200wifi/netdev.c
	net/wireless/scan.c
2009-07-23 19:03:51 -07:00
Linus Torvalds 402168cee1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
  sky2: Avoid races in sky2_down
  drivers/net/mlx4: Adjust constant
  drivers/net: Move a dereference below a NULL test
  drivers/net: Move a dereference below a NULL test
  connector: maintainer/mail update.
  USB host CDC Phonet network interface driver
  macsonic, jazzsonic: fix oops on module unload
  macsonic: move probe function to .devinit.text
  can: switch carrier on if device was stopped while in bus-off state
  can: restart device even if dev_alloc_skb() fails
  can: sja1000: remove duplicated includes
  New device ID for sc92031 [1088:2031]
  3c589_cs: re-initialize the multicast in the tc589_reset
  Fix error return for setsockopt(SO_TIMESTAMPING)
  netxen: fix thermal check and shutdown
  netxen: fix deadlock on dev close
  netxen: fix context deletion sequence
  net: Micrel KS8851 SPI network driver
  tcp: Use correct peer adr when copying MD5 keys
  tcp: Fix MD5 signature checking on IPv4 mapped sockets
  ...
2009-07-22 09:49:58 -07:00
Julia Lawall 86669530d9 drivers/net/mlx4: Adjust constant
The values in the advertising field are typically ADVERTISED_xxx, not
SUPPORTED_xxx.  Both SUPPORTED_10000baseT_Full and
ADVERTISED_1000baseT_Full have the same value.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct ethtool_cmd E;
@@
*E.advertising = SUPPORTED_10000baseT_Full
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21 13:00:46 -07:00
Yevgeny Petrilin 92bd3bbfbe mlx4_core: Add new ConnectX EN PCI ID 0x6764
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-07-06 16:10:40 -07:00
Yevgeny Petrilin cc4ac2e7fb mlx4_core: Handle multi-physical function devices
MT26468 (PCI ID 0x6764) devices can expose multiple physical
functions.  The current driver only handles the primary physical
function.  For other functions, the QUERY_FW firmware command will
fail with the CMD_STAT_MULTI_FUNC_REQ error code.  Don't try to drive
such devices, but print a message saying the driver is skipping those
devices rather than just "QUERY_FW command failed."

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>

[ Rather than keeping unsupported devices bound to the driver, simply
  print a more informative error message and exit - Roland ]

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-07-06 16:10:03 -07:00
Patrick McHardy ec634fe328 net: convert remaining non-symbolic return values in ndo_start_xmit() functions
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.

Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05 19:23:38 -07:00
Linus Torvalds 32708e8e95 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA: Add __init/__exit macros to addr.c and cma.c
  IB/ehca: Bump version number
  mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls
  IB/mthca: Replace dma_sync_single() use with proper functions
  RDMA/nes: Fix FIN state handling under error conditions
  RDMA/nes: Fix max_qp_init_rd_atom returned from query device
  IB/ehca: Ensure that guid_entry index is not negative
  IB/ehca: Tolerate dynamic memory operations before driver load
2009-06-23 11:36:01 -07:00
Roland Dreier e727f5cde9 mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls
Commit 5d23a1d2 ("net: replace dma_sync_single with
dma_sync_single_for_cpu") replaced uses of the deprectated function
dma_sync_single() with calls to dma_sync_single_for_cpu().  However,
to be correct, the code should do a sync for_cpu() before touching the
memory and for_device() after it's done.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-06-22 23:07:56 -07:00
Yevgeny Petrilin 0314db69d7 mlx4_en: Remove redundant refill code on RX
Our RX rings are always full, there is no need to check whether
we need to fill them or not. If we fail to allocate a new socket
buffer, the incoming packet is dropped an the ring remains full.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:07 -07:00
Yevgeny Petrilin 7237b40055 mlx4_en: Removed redundant check on lso header size
This check that verifies that the LSO header along with control
segment and first data segment do not cross 128 bytes is no longer
required.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:06 -07:00
Yevgeny Petrilin 3c05f5ef7c mlx4_en: Cancel port_up check in transmit function
When closing the port, we stop all transmit queues under the transmit
lock. It ensures that we will not attempt to transmit new packets after
the physical port was closed.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:05 -07:00
Yevgeny Petrilin a11faac79f mlx4_en: using stop/start_all_queues
After we moved to be a multi queue device, need to stop/start
all of our transmit queues.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:04 -07:00
Yevgeny Petrilin d4ddbaa6a9 mlx4_en: Removed redundant skb->len check
We don't need this check in the transmit function

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:03 -07:00
Yevgeny Petrilin 7e23091347 mlx4_en: Counting all the dropped packets on the TX side
Reporting the counter's value through 'ethtool -S'

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:02 -07:00
David S. Miller 9cbc1cb8cd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/scsi/fcoe/fcoe.c
	net/core/drop_monitor.c
	net/core/net-traces.c
2009-06-15 03:02:23 -07:00
Linus Torvalds cf5046323e Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
  IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
  IB/mlx4: Add strong ordering to local inval and fast reg work requests
  IB/ehca: Remove superfluous bitmasks from QP control block
  RDMA/cxgb3: Limit fast register size based on T3 limitations
  RDMA/cxgb3: Report correct port state and MTU
  mlx4_core: Add module parameter for number of MTTs per segment
  IB/mthca: Add module parameter for number of MTTs per segment
  RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
  infiniband: Remove void casts
  IB/ehca: Increment version number
  IB/ehca: Remove unnecessary memory operations for userspace queue pairs
  IB/ehca: Fall back to vmalloc() for big allocations
  IB/ehca: Replace vmalloc() with kmalloc() for queue allocation
2009-06-14 13:53:22 -07:00
Roland Dreier 8d34ff3401 Merge branches 'cxgb3', 'ehca', 'misc', 'mlx4', 'mthca' and 'nes' into for-linus 2009-06-14 13:31:19 -07:00
Roland Dreier d1fdf24b40 mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice.  Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.  This is the same bug that was reported in ib_mthca by Yinghai
Lu <yhlu.kernel@gmail.com>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-06-14 13:30:45 -07:00
Martin Olsson 98a1708de1 trivial: fix typos s/paramter/parameter/ and s/excute/execute/ in documentation and source comments.
Signed-off-by: Martin Olsson <martin@minimum.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-06-12 18:01:46 +02:00
Yevgeny Petrilin a5b19b635c mlx4: FIX error flow when initializing EQ table
If mlx4_create_eq() would fail for one of EQ's assigned for
completion handling, the code would try to free the same EQ
we failed to create.
The crash was found by Christoph Lameter

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08 00:39:58 -07:00
David S. Miller b2f8f7525c Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/forcedeth.c
2009-06-03 02:43:41 -07:00
Yevgeny Petrilin d455e5b165 mlx4_en: Updated driver version
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-02 02:36:32 -07:00
Yevgeny Petrilin e486973e9c mlx4_en: Added vlan_features support
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-02 02:29:08 -07:00
Yevgeny Petrilin f813cad836 mlx4_en: multiqueue support
By default the driver opens 8 TX queues (defined by MLX4_EN_NUM_TX_RINGS).
If the driver is configured to support Per Priority Flow Control, we open
8 additional TX rings.
dev->real_num_tx_queues is always set to be MLX4_EN_NUM_TX_RINGS.
The mlx4_en_select_queue() function uses standard hashing (skb_tx_hash)
in case that PPFC is not supported or the skb contain a vlan tag,
otherwise the queue is selected according to vlan priority.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-02 02:29:06 -07:00
Yevgeny Petrilin 3db36fb2c8 mlx4_en: Coalescing target is equal for all mtu's
The interrupt moderation should not depend on number of incoming
bytes, but on number of incoming packets.
The previous scheme caused very high interrupts rate for small
messages when big MTU was configured.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-02 02:29:06 -07:00
Yevgeny Petrilin 3c2fa83f9c mlx4_en: Work with part of the ports.
If the initialization of one of the ports failed,
there is no need to fail the other one as well.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-02 02:29:05 -07:00
Yevgeny Petrilin 9e47edaa1a mlx4_en renamed en_params.c to en_ethtool.c
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-02 02:29:04 -07:00
Yevgeny Petrilin a2b28737a2 mlx4_en: Moved all module parameters handling to en_main.c
en_params.c file now only handles Ethtool functionality

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-02 02:29:03 -07:00
Yevgeny Petrilin 453a608277 mlx4_en: Giving interface name in debug messages
For each debug message, the message will show interface name in case
that the net device was registered, and PCI bus ID with port number
if we were not registered yet. Messages that are not port/netdev specific
stayed in the old format

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-02 02:29:03 -07:00
Yevgeny Petrilin 465440d272 mlx4_en: Fix a kernel panic when waking tx queue
When the transmit queue gets full we enable interrupts for TX completions
There was a race that we handled the TX queue both from the interrupt context
and from the transmit function. Using "spin_trylock_irq()" ensures this
doesn't happen.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29 22:04:42 -07:00
FUJITA Tomonori 5d23a1d2a3 net: replace dma_sync_single with dma_sync_single_for_cpu
This replaces dma_sync_single() with dma_sync_single_for_cpu() because
dma_sync_single() is an obsolete API; include/linux/dma-mapping.h says:

/* Backwards compat, remove in 2.7.x */
#define dma_sync_single		dma_sync_single_for_cpu
#define dma_sync_sg		dma_sync_sg_for_cpu

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29 01:51:22 -07:00
Eric Dumazet 28679751a9 net: dont update dev->trans_start in 10GB drivers
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.

Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29 01:46:26 -07:00
Eli Cohen ab6bf42e23 mlx4_core: Add module parameter for number of MTTs per segment
The current MTT allocator uses kmalloc() to allocate a buffer for its
buddy allocator, and thus is limited in the amount of MTT segments
that it can control.  As a result, the size of memory that can be
registered is limited too.  This patch uses a module parameter to
control the number of MTT entries that each segment represents,
allowing more memory to be registered with the same number of
segments.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-05-27 14:38:34 -07:00
Yevgeny Petrilin 38aab07c14 mlx4_en: Fix partial rings feature
In case of allocation failure, the actual ring size is rounded down to
nearest power of 2. The remaining descriptors are freed.
The CQ and SRQ are allocated with the actual size and the mask is updated.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-25 00:35:53 -07:00
Yevgeny Petrilin 8e29291650 mlx4_en: Removed redundant stride variable
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-25 00:35:52 -07:00