As soon as the netdev is registers, the kernel can start using the
interface. If the driver connects the MAC to the PHY after the netdev
is registered, there is a race condition where the interface can be
opened without having the PHY connected.
Change the order to close this race condition.
Fixes: 92571a1aae ("lan78xx: Connect phy early")
Reported-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial state information must not be embedded into another
data structure, as this interferes with cache handling for DMA
on architectures without cache coherence..
That would result in data corruption on some architectures
Allocating it separately.
v2: fix syntax error
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure res does not contain random value if the call to
sr_read_cmd fails for some reason.
Reported-by: syzbot+f1842130bbcfb335bac1@syzkaller.appspotmail.com
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 may fail to establish network connection after resume from system
suspend.
If the USB port connects to r8152 lost its power during system suspend,
the MAC address was written before is lost. The reason is that The MAC
address doesn't get written again in its reset_resume callback.
So let's set MAC address again in reset_resume callback. Also remove
unnecessary lock as no other locking attempt will happen during
reset_resume.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL-pointer dereference on tty open due to a failure to handle a
missing interrupt-in endpoint when probing modem ports:
BUG: kernel NULL pointer dereference, address: 0000000000000006
...
RIP: 0010:tiocmget_submit_urb+0x1c/0xe0 [hso]
...
Call Trace:
hso_start_serial_device+0xdc/0x140 [hso]
hso_serial_open+0x118/0x1b0 [hso]
tty_open+0xf1/0x490
Fixes: 542f548236 ("tty: Modem functions for the HSO driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the drivers more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of these endpoints are used for memory allocations
and as divisors in many usbnet minidrivers. Avoiding zero is therefore
critical.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the driver more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of the out pipe is used as divisor. So this change
fixes a divide-by-zero bug.
Reported-by: syzbot+ce366e2b8296e25d84f5@syzkaller.appspotmail.com
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
After a reset packet sizes and device mtu can change and need
to be reevaluated to calculate queue sizes.
Malicious devices can set this to zero and we divide by it.
Introduce sanity checking.
Reported-and-tested-by: syzbot+6102c120be558c885f04@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Mediatek based smartphone owner reports problems with USB
tethering in Linux. The verbose USB listing shows a rndis_host
interface pair (e0/01/03 + 10/00/00), but the driver fails to
bind with
[ 355.960428] usb 1-4: bad CDC descriptors
The problem is a failsafe test intended to filter out ACM serial
functions using the same 02/02/ff class/subclass/protocol as RNDIS.
The serial functions are recognized by their non-zero bmCapabilities.
No RNDIS function with non-zero bmCapabilities were known at the time
this failsafe was added. But it turns out that some Wireless class
RNDIS functions are using the bmCapabilities field. These functions
are uniquely identified as RNDIS by their class/subclass/protocol, so
the failing test can safely be disabled. The same applies to the two
types of Misc class RNDIS functions.
Applying the failsafe to Communication class functions only retains
the original functionality, and fixes the problem for the Mediatek based
smartphone.
Tow examples of CDC functional descriptors with non-zero bmCapabilities
from Wireless class RNDIS functions are:
0e8d:000a Mediatek Crosscall Spider X5 3G Phone
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x0f
connection notifications
sends break
line coding and serial state
get/set/clear comm features
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
and
19d2:1023 ZTE K4201-z
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC Union:
bMasterInterface 0
bSlaveInterface 1
The Mediatek example is believed to apply to most smartphones with
Mediatek firmware. The ZTE example is most likely also part of a larger
family of devices/firmwares.
Suggested-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UPS feature only works for runtime suspend, so UPS flags only
need to be set before enabling runtime suspend. Therefore, I create
a struct to record relative information, and use it before runtime
suspend.
All chips could record such information, even though not all of
them support the feature of UPS. Then, some functions could be
combined.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, for AUTONEG_DISABLE, we only need to modify MII_BMCR.
Second, add advertising parameter for rtl8152_set_speed(). Add
RTL_ADVERTISED_xxx for advertising parameter of rtl8152_set_speed().
Then, the advertising settings from ethtool could be saved.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary use of netif_napi_del. This also avoids to call
napi_disable() after netif_napi_del().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0ee1f47349.
The commit 0ee1f47349 ("r8152: napi hangup fix after
disconnect") adds a check about RTL8152_UNPLUG to determine
if calling napi_disable() is invalid in rtl8152_close(),
when rtl8152_disconnect() is called. This avoids to use
napi_disable() after calling netif_napi_del().
Howver, commit ffa9fec30c ("r8152: set RTL8152_UNPLUG
only for real disconnection") causes that RTL8152_UNPLUG
is not always set when calling rtl8152_disconnect().
Therefore, I have to revert commit 0ee1f47349 ("r8152:
napi hangup fix after disconnect"), first. And submit
another patch to fix it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_registers() blindly copies the memory written to by the
usb_control_msg() call even if the underlying urb failed.
This could lead to junk register values being read by the driver, since
some indirect callers of get_registers() ignore the return values. One
example is:
ocp_read_dword() ignores the return value of generic_ocp_read(), which
calls get_registers().
So, emulate PCI "Master Abort" behavior by setting the buffer to all
0xFFs when usb_control_msg() fails.
This patch is copied from the r8152 driver (v2.12.0) published by
Realtek (www.realtek.com).
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function "rtl_eee_enable" for setting EEE. Besides, I
move r8153_eee_en() and r8153b_eee_en(). And, I remove r8152b_enable_eee(),
r8153_set_eee(), and r8153b_set_eee().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saving the settings of EEE to avoid they become the default settings
after reset_resume().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the tx bottom function from NAPI to a new tasklet. Then, for
multi-cores, the bottom functions of tx and rx may be run at same
time with different cores. This is used to improve performance.
On x86, Tx/Rx 943/943 Mbits/sec -> 945/944.
For arm platform, Tx/Rx: 917/917 Mbits/sec -> 933/933.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix accessing skb after napi_gro_receive which is caused by
commit 47922fcde5 ("r8152: support skb_add_rx_frag").
Fixes: 47922fcde5 ("r8152: support skb_add_rx_frag")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kalmia_init_and_get_ethernet_addr(), 'usb_buf' is allocated through
kmalloc(). In the following execution, if the 'status' returned by
kalmia_send_init_packet() is not 0, 'usb_buf' is not deallocated, leading
to memory leaks. To fix this issue, add the 'out' label to free 'usb_buf'.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cx82310_bind(), 'dev->partial_data' is allocated through kmalloc().
Then, the execution waits for the firmware to become ready. If the firmware
is not ready in time, the execution is terminated. However, the allocated
'dev->partial_data' is not deallocated on this path, leading to a memory
leak bug. To fix this issue, free 'dev->partial_data' before returning the
error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In lan78xx_probe(), a new urb is allocated through usb_alloc_urb() and
saved to 'dev->urb_intr'. However, in the following execution, if an error
occurs, 'dev->urb_intr' is not deallocated, leading to memory leaks. To fix
this issue, invoke usb_free_urb() to free the allocated urb before
returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the rx_copybreak and rx_pending could be modified by
ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use skb_add_rx_frag() to reduce the memory copy for rx data.
Use a new list of rx_used to store the rx buffer which couldn't be
reused yet.
Besides, the total number of rx buffer may be increased or decreased
dynamically. And it is limited by RTL8152_MAX_RX_AGG.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Replace kmalloc_node() with alloc_pages() for rx buffer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The original method uses an array to store the rx information. The
new one uses a list to link each rx structure. Then, it is possible
to increase/decrease the number of rx structure dynamically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The different chips may accept different rx buffer sizes. The RTL8152
supports 16K bytes, and RTL8153 support 32K bytes.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
It is likely that PAL_BDC_CR should be PLA_BDC_CR.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_registers() may fail with -ENOMEM and in this
case we can read a garbage from the status variable tmp.
Reported-by: syzbot+3499a83b2d062ae409d4@syzkaller.appspotmail.com
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BroadMobi BM818 M.2 card uses the QMI protocol
Signed-off-by: Bob Ham <bob.ham@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the combo uses of cpu_to_le32s and memcpy.
Use put_unaligned_le32 instead.
This simplifies the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the combo use of memcpy and le32_to_cpus.
Use get_unaligned_le32 instead.
This simplifies the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the combo use of memcpy and le32_to_cpus.
Use get_unaligned_le32 instead.
This simplifies the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the combo use of memcpy and lexx_to_cpus.
Use get_unaligned_lexx instead.
This simplifies the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the flag of RTL8152_UNPLUG if and only if the device is unplugged.
Some error codes sometimes don't mean the real disconnection of usb device.
For those situations, set the flag of RTL8152_UNPLUG causes the driver skips
some flows of disabling the device, and it let the device stay at incorrect
state.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8153b_rx_agg_chg_indicate() needs to be called after enabling TX/RX and
before calling rxdy_gated_en(tp, false). Otherwise, the change of the
settings of RX aggregation wouldn't work.
Besides, adjust rtl8152_set_coalesce() for the same reason. If
rx_coalesce_usecs is changed, restart TX/RX to let the setting work.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Rename r8153b_queue_wake() to r8153_queue_wake().
2. Correct the setting. The enable bit should be 0xd38c bit 0. Besides,
the 0xd38a bit 0 and 0xd398 bit 8 have to be cleared for both enabled
and disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syzbot reported
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x67/0x231 mm/kasan/report.c:188
__kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
kasan_report+0xe/0x20 mm/kasan/common.c:614
qmi_wwan_probe+0x342/0x360 drivers/net/usb/qmi_wwan.c:1417
usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
Caused by too many confusing indirections and casts.
id->driver_info is a pointer stored in a long. We want the
pointer here, not the address of it.
Thanks-to: Hillf Danton <hdanton@sina.com>
Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Fixes: e4bf63482c ("qmi_wwan: Add quirk for Quectel dynamic config")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Andrew Lunn