No core changes this time.
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins
with another CPU using a hardware spinlock.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcKN2qAAoJEEEQszewGV1zK5wP/2QbrvH8eW+mF9YD+1fr11Sp
oCe52C7n1YMKt5R6vSFyLtqPYDehCP9gTS0Zlbz4HKyTe2E9OIuigrmg+1uQwxWp
GSvxmMx9QFlNqUcWOvc90DYDfOh5ZPVIsP16k3DIlodVsQlSu4O4KF0pJseRyuSh
PVn/MjPrGtyTB2TJzO/Oj3sadHhVRzTb6Zlk7uk5hak6ys5AYHetBHhuxAcicFv4
OGwEOvaV5DiTO5wbbyNSmkF5NI+ApV2o4DRRNTXC+mJJSPCpQxFskLTmHu9wYKmE
/p6Gp9dtxSS3QLA4NXsY+IrFJsU1q261gEvIsFa2upW5j7T8bLzRAzoFG+/dil6t
k5GDnx8t7qSPXLme8/nJlX40O2CJs4sXKwCQY4vjsySW31ryqBMm4JNSQKTxe9Ma
1RrZ7UR+P6IwupUsEYZkcneuu+oGMNYpbDG48R2utgECY4KN17wUjjZHkYHZNiDi
Yk/CMkOXXuZnAZGfmaj8R9yjkjFZMZAqOYDJcruMzLFjAkw6fCmFipZLoSIN4+sJ
u4RERrbsF+e5PY4BOfxYw5NIzTl60AQquttj//RJyLQDsQ/HMU9jaovW6E3JQytO
NgU9RtEwrtK50ef5OYS4EtTlNi2B3arU83noI/oX3R52SoAIdMTHtVMgyECm3dMg
XeLn9x2Ffy7a4PRruLoy
=cm6m
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"We have no core changes but lots of incremental development in drivers
all over the place: Renesas, NXP, Mediatek and Actions Semiconductor
keep churning out new SoCs.
I have some subtree maintainers for Renesas and Intel helping out to
keep down the load, it's been working smoothly (Samsung also have a
subtree but it was not used this cycle.)
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins with
another CPU using a hardware spinlock"
* tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits)
dt-bindings: arm: fsl-scu: add imx8qm pinctrl support
pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ
pinctrl: imx-scu: Depend on IMX_SCU
pinctrl: ocelot: Add dependency on HAS_IOMEM
pinctrl: ocelot: add MSCC Jaguar2 support
pinctrl: bcm: ns: support updated DT binding as syscon subnode
dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon
MAINTAINERS: merge at91 pinctrl entries
pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP
pinctrl: uniphier: constify uniphier_pinctrl_socdata
pinctrl: mediatek: improve Kconfig dependencies
pinctrl: msm: mark PM functions as __maybe_unused
dt-bindings: pinctrl: sunxi: Add supply properties
pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins
pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins
pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
...
Without CONFIG_PM_SLEEP, we get annoying warnings about unused functions:
drivers/pinctrl/qcom/pinctrl-msm.c:1082:12: error: 'msm_pinctrl_resume' defined but not used [-Werror=unused-function]
static int msm_pinctrl_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
drivers/pinctrl/qcom/pinctrl-msm.c:1075:12: error: 'msm_pinctrl_suspend' defined but not used [-Werror=unused-function]
static int msm_pinctrl_suspend(struct device *dev)
Mark them as __maybe_unused to shut up the warning and silently drop
the functions without having to add ugly #ifdefs.
Fixes: 977d057ad3 ("pinctrl: msm: Add sleep pinctrl state transitions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This was missed when tiles support was added in a revison and
causes the driver to fail to load.
Fixes: 9cf0c526bc ("pinctrl: qcom: Add sdm660 pinctrl driver")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PM suspend callbacks to the msm core driver that select the
sleep and default pinctrl states. Then wire those callbacks up
in the sdm845 driver, for those boards that may have GPIO hogs
that need to change state during suspend.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When attempting to setup up a gpio hog, device probing will repeatedly
fail with -EPROBE_DEFERED errors. It is caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.
See Christian Lamparter's commit a86caa9ba5 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.
I did not test this change against any hardware supported by this
particular driver, however I was able to validate this same fix works
for pinctrl-spmi-gpio.c using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When attempting to setup up a gpio hog, device probing would repeatedly
fail with -EPROBE_DEFERED errors. It was caused by a circular dependency
between the gpio and pinctrl frameworks. If the gpio-ranges property is
present in device tree, then the gpio framework will handle the gpio pin
registration and eliminate the circular dependency.
See Christian Lamparter's commit a86caa9ba5 ("pinctrl: msm: fix
gpio-hog related boot issues") for a detailed commit message that
explains the issue in much more detail. The code comment in this commit
came from Christian's commit.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbzdyOAAoJEEEQszewGV1zfYcP/0HBEAOPhHD/i5OQxfKs1msh
mFT/t/IbTmRpCgbEv4CDx4Kc/InE0sUnQr1TL/1WvU6uObM6Ncxq5Z90MvyrgzYu
BqQHq2k2tORvkVSNRxcfD/BAAoo1EerXts1kDhutvdKfepfS6DxpENwzvsFgkVlq
2jj1cdZztjv8A+9cspHDpQP+jDvl1VSc10nR5fRu1TttSpUwzRJaB30NBNXJmMJc
5KUr67lEbsQRPsBvFErU11bydPqhfT+pXmODcfIwS0EtATQ8WC5mkSb/Ooei0fvT
oZ7uR3Os8tMf7isOKssEyFabKwhnfOEt6TBt9em0TfUtInOo0Dc7r8TfBcn57fyZ
xg2R9DQEVRfac8bjhF/BI5KHuN9IMGDDvj6XApumQVliZbISRjMnh3jte6RpcV0A
Ejqz8FeDY13qvEdOnW1EPpwmXdDVWiEAq0ebGLStKNls+/4gB2HmyxGUOzJf+og5
hujsxcJzGQqjCe0moeY/1d7vsy0ZjbHoS+p5fy79U212y2O7onEzFU92AX89bxKC
rx2eCNmiZxCUy1nqu8edO62VnH6QdnqG3o+a4DJfCSHPvFM/E/NX9zHemZubQQ4I
rYXNy4bL4tEG9cqWMfBxWrpiDZw7H6l8kXwdZG8IMyRU9BcKu96amgZ+jBXwzoaB
JZelAAUWB9APghJYFr7o
=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
The current code produces XPU violation if get_direction is called just
after the initialization.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'tiles' array is initialized to a constant pointers to constant
strings, but the declaration is only half as constant:
drivers/pinctrl/qcom/pinctrl-qcs404.c:1660:11: error: initialization discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
drivers/pinctrl/qcom/pinctrl-sdm660.c:1417:11: error: initialization discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
Let's make it more constant.
Fixes: 22eb8301db ("pinctrl: qcom: Add qcs404 pinctrl driver")
Fixes: a46d5e9819 ("pinctrl: qcom: Support dispersed tiles")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This code needs to select function #0, which is the first int in the
array of functions, not the number 0 which may or may not be the
function for "GPIO mode" per the enum mapping. We were getting lucky on
SDM845, where this was tested, because the function 0 matched the enum
value for "GPIO mode". On other platforms, e.g. MSM8996, the gpio enum
value is the last one in the list so this code doesn't work and we see a
warning at boot. Fix it by grabbing the first element out of the array
of functions.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Fixes: 1de7ddb3a1 ("pinctrl: msm: Mux out gpio function with gpio_request()")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into devel
This is the 4.19-rc6 release
I needed to merge this in because of extensive conflicts in
the MSM and Intel pin control drivers. I know how to resolve
them, so let's do it like this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration with
pinctrl framework for qcs404.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Chintan Pandya <cpandya@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
[bjorn: Reworked tile handling and did some minor rework]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some new platforms the tiles have been placed too far apart to be
covered in a single ioremap. Turn "regs" into an array of base addresses
and make the pingroup carry the information about which tile the pin
resides in.
For existing platforms we map the first entry regs and the existing
pingroups will all use tile 0, meaning that there's no functional
change.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation for the support for dispersed tiles move all readl and
writel calls to helper functions. This will allow us to isolate the
added complexity of another indirection.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'ret' should be returned while pmic_mpp_write_mode_ctl fails.
Fixes: 0e948042c4 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It looks like we parse the drive strength setting here, but never
actually write it into the hardware to update it. Parse the setting and
then write it at the end of the pinconf setting function so that it
actually sticks in the hardware.
Fixes: 0e948042c4 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If you look at "pinconf-groups" in debugfs for ssbi-mpp you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc212 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c82895 ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-mpp has the same
problem. Let's fix it there too.
NOTE: in case it's helpful to someone reading this, the way to tell
whether to do the -EINVAL or not is to look at the PCONFDUMP for a
given attribute. If the last element (has_arg) is false then you need
to do the -EINVAL trick.
ALSO NOTE: it seems unlikely that the values returned when we try to
get PIN_CONFIG_BIAS_PULL_UP will actually be printed since "has_arg"
is false for that one, but I guess it's still fine to return different
values so I kept doing that. It seems like another driver (ssbi-gpio)
uses a custom attribute (PM8XXX_QCOM_PULL_UP_STRENGTH) for something
similar so maybe a future change should do that here too.
Fixes: cfb24f6ebd ("pinctrl: Qualcomm SPMI PMIC MPP pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If you look at "pinconf-groups" in debugfs for ssbi-gpio you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc212 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c82895 ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-gpio has the same
problem. Let's fix it there too.
Fixes: b4c45fe974 ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When requesting a gpio as an interrupt, we should make sure to mux the
pin as the GPIO function and configure it to be an input so that various
functions or output signals don't affect the interrupt state of the pin.
So far, we've relied on pinmux configurations in DT to handle this, but
let's explicitly configure this in the code so that DT implementers
don't have to get this part right.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We rely on devices to use pinmuxing configurations in DT to select the
GPIO function (function 0) if they're going to use the gpio in GPIO
mode. Let's simplify things for driver authors by implementing
gpio_request_enable() for this pinctrl driver to mux out the GPIO
function when the gpio is use from gpiolib.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt controller hardware in this pin controller has two status
enable bits. The first "normal" status enable bit enables or disables
the summary interrupt line being raised when a gpio interrupt triggers
and the "raw" status enable bit allows or prevents the hardware from
latching an interrupt into the status register for a gpio interrupt.
Currently we just toggle the "normal" status enable bit in the mask and
unmask ops so that the summary irq interrupt going to the CPU's
interrupt controller doesn't trigger for the masked gpio interrupt.
For a level triggered interrupt, the flow would be as follows: the pin
controller sees the interrupt, latches the status into the status
register, raises the summary irq to the CPU, summary irq handler runs
and calls handle_level_irq(), handle_level_irq() masks and acks the gpio
interrupt, the interrupt handler runs, and finally unmask the interrupt.
When the interrupt handler completes, we expect that the interrupt line
level will go back to the deasserted state so the genirq code can unmask
the interrupt without it triggering again.
If we only mask the interrupt by clearing the "normal" status enable bit
then we'll ack the interrupt but it will continue to show up as pending
in the status register because the raw status bit is enabled, the
hardware hasn't deasserted the line, and thus the asserted state latches
into the status register again. When the hardware deasserts the
interrupt the pin controller still thinks there is a pending unserviced
level interrupt because it latched it earlier. This behavior causes
software to see an extra interrupt for level type interrupts each time
the interrupt is handled.
Let's fix this by clearing the raw status enable bit for level type
interrupts so that the hardware stops latching the status of the
interrupt after we ack it. We don't do this for edge type interrupts
because it seems that toggling the raw status enable bit for edge type
interrupts causes spurious edge interrupts.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If you do this on an sdm845 board:
grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups
...it looks like nonsense. For every pin you see listed:
input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...
That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects. Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.
Let's fix this.
From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist. I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases. While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.
NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE. Oops.
Fixes: eadff30244 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If you do this on an sdm845 board:
cat /sys/kernel/debug/pinctrl/3400000.pinctrl/pinconf-groups
...it looks like nonsense. For every pin you see listed:
input bias bus hold, input bias disabled, input bias pull down, input bias pull up
That's because msm_config_group_get() isn't complying with the rules
that pinconf_generic_dump_one() expects. Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.
Let's fix this.
From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist. I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases. While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sven Eckelmann reported an issue with the current IPQ4019 pinctrl.
Setting up any gpio-hog in the device-tree for his device would
"kill the bootup completely":
| [ 0.477838] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 0.499828] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferring probe
| [ 1.298883] requesting hog GPIO enable USB2 power (chip 1000000.pinctrl, offset 58) failed, -517
| [ 1.299609] gpiochip_add_data: GPIOs 0..99 (1000000.pinctrl) failed to register
| [ 1.308589] ipq4019-pinctrl 1000000.pinctrl: Failed register gpiochip
| [ 1.316586] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 1.322415] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferri
This was also verified on a RT-AC58U (IPQ4018) which would
no longer boot, if a gpio-hog was specified. (Tried forcing
the USB LED PIN (GPIO0) to high.).
The problem is that Pinctrl+GPIO registration is currently
peformed in the following order in pinctrl-msm.c:
1. pinctrl_register()
2. gpiochip_add()
3. gpiochip_add_pin_range()
The actual error code -517 == -EPROBE_DEFER is coming from
pinctrl_get_device_gpio_range(), which is called through:
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_gpios
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
gpiochip_generic_request
pinctrl_gpio_request
pinctrl_get_device_gpio_range
pinctrl_get_device_gpio_range() is unable to find any valid
pin ranges, since nothing has been added to the pinctrldev_list yet.
so the range can't be found, and the operation fails with -EPROBE_DEFER.
This patch fixes the issue by adding the "gpio-ranges" property to
the pinctrl device node of all upstream Qcom SoC. The pin ranges are
then added by the gpio core.
In order to remain compatible with older, existing DTs (and ACPI)
a check for the "gpio-ranges" property has been added to
msm_gpio_init(). This prevents the driver of adding the same entry
to the pinctrldev_list twice.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I was debugging some gpio issues and I thought that the output of gpio
debugfs was telling me the high or low level of the gpios with a '1' or
a '0'. We saw a line like this though:
gpio93 : in 4 2mA pull down
and I started to think that there may be a gas leak in the building
because '4' doesn't mean high or low, and other pins said '0' or '1'. It
turns out, '4' is the function selection for the pinmux of the gpio and
not the value on the pin. Reading code helps decipher what debugfs is
actually saying.
Add support to read the input or output pin depending on how the pin is
configured so we can easily see the high or low value of the pin in
debugfs. Now the output looks like
gpio93 : in low func4 2mA pull down
which clearly shows that the pin is an input, low, with function 4 and a
2mA drive strength plus a pull down.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DebugFS strings about pin pull status for no_keeper SoC are wrong
Fix this by adding a different string array for no_keeper SoC
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Newer versions of the firmware for the Qualcomm Datacenter Technologies
QDF2400 restricts access to a subset of the GPIOs on the TLMM. To
prevent older kernels from accidentally accessing the restricted GPIOs,
we change the ACPI HID for the TLMM block from QCOM8001 to QCOM8002,
and introduce a new property "gpios". This property is an array of
specific GPIOs that are accessible. When an older kernel boots on
newer (restricted) firmware, it will fail to probe.
To implement the sparse GPIO map, we register all of the GPIOs, but
fill in the data only for available GPIOs. This ensures that the driver
cannot accidentally access an unavailable GPIO.
The pinctrl-msm driver also scans the "gpios" property to determine
which pins are available, and ensure that only those can be registered.
Support for QCOM8001 is removed as there is no longer any firmware that
implements it.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Two data structures are declared as static globals but are intended to
be per-TLMM. Move them into the msm_pinctrl structure and initialize
them at runtime.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of
depending on it. This is merged with the same pattern
for all the ISA drivers and some other Kconfig cleanups
related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of
this SoC from the ARM tree.
- Move the documentation over to driver-api to conform with
the rest of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h>
that we want to get rid of.
- Managed to remove VLA allocation from two drivers pending
more fixes in this area for the next merge window.
- Misc janitorial fixes.
-----BEGIN PGP SIGNATURE-----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=C5t5
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
Some qcom platforms make some GPIOs or pins unavailable for use
by non-secure operating systems, and thus reading or writing the
registers for those pins will cause access control issues and
reset the device. With a DT/ACPI property to describe the set of
pins that are available for use, parse the available pins and set
the irq valid bits for gpiolib to know what to consider 'valid'.
This should avoid any issues with gpiolib. Furthermore, implement
the pinmux_ops::request function so that pinmux can also make
sure to not use pins that are unavailable.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The base of the TLMM gpiochip should not be statically defined as 0, fix
this to not artificially restrict the existence of multiple pinctrl-msm
devices.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the pinctrl definitions for the TLMM of SDM845.
Signed-off-by: Kyle Yan <kyan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
CORE:
- Fix the semantics of raw GPIO to actually be raw. No
inversion semantics as before, but also no open draining,
and allow the raw operations to affect lines used for
interrupts as the caller supposedly knows what they are
doing if they are getting the big hammer.
- Rewrote the __inner_function() notation calls to names that
make more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all
IRQs are mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This
allows us to read several GPIO lines with a single
register read. This has high value for some usecases: it
can be used to create oscilloscopes and signal analyzers
and other things that rely on reading several lines at
exactly the same instant. Also a generally nice
optimization. This uses the new assign_bit() macro from
the bitops lib that was ACKed by Andrew Morton and
is implemented for two drivers, one of them being the
generic MMIO driver so everyone using that will be able
to benefit from this.
- Do not allow requests of Open Drain and Open Source
setting of a GPIO line simultaneously. If the hardware
actually supports enabling both at the same time the
electrical result would be disastrous.
- A new interrupt chip core helper. This will be helpful
to deal with "banked" GPIOs, which means GPIO controllers
with several logical blocks of GPIO inside them. This
is several gpiochips per device in the device model, in
contrast to the case when there is a 1-to-1 relationship
between a device and a gpiochip.
NEW DRIVERS:
- Maxim MAX3191x industrial serializer, a very interesting
piece of professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the
recent Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
OTHER IMPROVEMENTS:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the
Broadcom BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal
of dead code etc.
- Explicit comments on fall-through switch() statements.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaCvGiAAoJEEEQszewGV1z+oAQAJUpdPH/msdgHDuXSuBcbuFq
NObQdkRiz1hez4vJOT+kbgES6ay57MArnbmM/xRdy+37lKrmkP+yfZe4UUruQhhW
f2GVlwBbUp9tIzNliS8IYWO0tj+BTYyg1MQx0C0nE1zMZqVZk44EDa9SO6esRaFJ
SLc2BpO3oJCQRaObe0+KTHIJV0dK3vQh4QXSzL+cM5u7P67Jq+wv4xdLVVScwbJB
4jgwVER3Ah0E1jHclIG2PxI1rbYKwlOBumafOTUlq5fmfC3tULVPJEm9FXcdaBLJ
KAmtxX4yi+SgUccYFsmK+fNNLVQiAjmkhJCl6kxVOrxYqamrG100YST4Iew3sakM
/iQ3lpup5L6eJ/dndfgE207OqRFhvAzNRxORv1p/wJIRLmV1/QehCX8GYOcDumXY
MySRcEeUeZPfBHcnjIDRP6y/XOg8zBKso7GL+feRgLZUJZlNQZqokdC95TY9S5nm
QLK+sU367o41tomyv5TP3y1DDsym6+ZdpuOUh73znxuz2x/x+FfTfwM2J0r8Ussm
GQTfAojeBI9aSOZ2mvgRI1XxSprXqO3FFFWBwrQ6RS9rBceLF1o2ySKC2gI0FG5d
6GBkARcN5RyyNtYkH923pyrqz/FZJc6ZkrsUTGmERM5HGuWwczcditqwYRhbHwl8
pIlmX4y0AYh6FFVoIcQE
=8Mon
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the binding and driver for pmi8994-gpios
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GPIO is expected to be disabled iff PIN_CONFIG_BIAS_HIGH_IMPEDANCE is
configured. Update is_enabled flag in config_set() so that it can
reflect GPIO status correctly. Also modify EN_CTL register based on
is_enabled flag in config_set() to configure the GPIO properly.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Power source selection in DIG_VIN_CTL is indexed from 0, in the range
check it shouldn't be equal to the total number of power sources.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add property "qcom,dtest-buffer" to specify which dtest rail to feed
when the pin is configured as a digital input.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
15136 5112 0 20248 4f18 drivers/pinctrl/qcom/pinctrl-ssbi-mpp.o
after:
bss dec hex filename
14849 5024 0 19873 4da1 drivers/pinctrl/qcom/pinctrl-ssbi-mpp.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds