This patch adds support for the 88x2110 PHY, which is similar to the
already supported 88x3310 PHY without the SFP interface.
It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET,
with the same interface modes that are used by the 3310.
This PHY don't have the same issue as the 88x3310 regarding 2.5/5G
abilities, and correctly follows the 802.3bz standard to list the
supported abilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY ID corresponding to the 88X3310 is also used for other PHYs in
the same family, such as the 88E2010. Use a #define for the PHY id, that
ignores the last nibble.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way to define __ETHTOOL_LINK_MODE_MASK_NBITS seems to be overly
complicated, go with a standard approach instead.
Whilst we're at it, move the comment to the right place.
v2:
- rebased
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce dev_change_proto_down_generic, a generic ndo_change_proto_down
implementation, which sets the netdev carrier state according to proto_down.
This adds the ability to set protodown on vxlan and macvlan devices in a
generic way for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A detail for mac_config() had been missed in the documentation for the
method - it is expected that the method will update the MAC to the
settings, rather than completely reprogram the MAC on each call.
Update the documentation for this method for this detail.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_read_status() for Clause 22 add a generic read_status
function for Clause 45.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds some misc updates to mlx5 driver,
1) Eli Britstein, Introduces tunnel entropy control from PCMR register
and fixes GRE key by controlling port tunnel entropy calculation.
2) Eran Ben Elisha, provides some mlx5 fixes to the latest tx devlink health
reporting mechanism.
3) Huy Nguyen, Added the support for ndo bridge_setlink to allow
VEPA/VEB E-Switch legacy mode configurations.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccGvRAAoJEEg/ir3gV/o+6kIH/1Y23h0OZrKkkfELujtzoOjx
64BIRhW8Tr+WOXZNKlSvdRkPj0g1yG3B0NO7wChXZDl8dgqBp/Jx5Wxcvb5DKkz/
wK07oKB6KqgcMILzUe5G4iOHw/atMldzSA6sNPh8SDKVKKkXjMKz8ocQZZQRsAaX
1im2D77pX8zE/OhG86Fn23Fed1G6Lg++faPC8GEOxv9LkwaAARa5NfJ6g7AnXOGg
ijmM4R2Hhu0V0YaKXS2qJFb6HQaNO9JKYR1C7wF7z9yqnsn14cdxrAWkE4eA2JnP
zKnDt+ThAKAoX9mn5QHzD8uye56Jeksvo8br4dCH4iDZZSSZT+lo456Dfe+tXpc=
=ef79
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-02-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-02-21
This series adds some misc updates to mlx5 driver,
1) Eli Britstein, Introduces tunnel entropy control from PCMR register
and fixes GRE key by controlling port tunnel entropy calculation.
2) Eran Ben Elisha, provides some mlx5 fixes to the latest tx devlink health
reporting mechanism.
3) Huy Nguyen, Added the support for ndo bridge_setlink to allow
VEPA/VEB E-Switch legacy mode configurations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow entropy is calculated on the inner packet headers and used for
flow distribution in processing, routing etc. For GRE-type
encapsulations the entropy value is placed in the eight LSB of the key
field in the GRE header as defined in NVGRE RFC 7637. For UDP based
encapsulations the entropy value is placed in the source port of the
UDP header.
The hardware may support entropy calculation specifically for GRE and
for all tunneling protocols. With commit df2ef3bff1 ("net/mlx5e: Add
GRE protocol offloading") GRE is offloaded, but the hardware is
configured by default to calculate flow entropy so packets transmitted
on the wire have a wrong key. To support UDP based tunnels (i.e VXLAN),
GRE (i.e. no flow entropy) and NVGRE (i.e. with flow entropy) the
hardware behaviour must be controlled by the driver.
Ensure port entropy calculation is enabled for offloaded VXLAN tunnels
and disable port entropy calculation in the presence of offloaded GRE
tunnels by monitoring the presence of entropy enabling tunnels (i.e
VXLAN) and entropy disabing tunnels (i.e GRE).
Fixes: df2ef3bff1 ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When using the device packet encapsulation offload, the device
calculates an entropy value, representing the inner packet headers. The
entropy field is placed inside the outer packet headers. For UDP-type
encapsulations, the entropy is placed in the source port field of the
UDP header. For GRE-type encapsulations, the entropy is placed in the 8
LSB of the key field in the GRE header. If the device does not recognize
the encapsulation type, the entropy is not placed in the packet.
Entropy setting can be controlled using PCMR register. if encapsulation
offload is not used force_entropy_cap should be set to 0x0. Entropy
setting is enabled/disabled using entropy_calc, and could be
additionally enabled/disabled for GRE encapsulation by entropy_gre_calc.
As a pre-step to automatically control the tunnel entropy, introduce
the entropy fields in the PCMR register with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJccAnlAAoJEG4XJFUm622bxxMH/2cz2GEuDQXOwfYLnCUwFES8
vqTdMWnlfqGQvsTyvtSp91KqsL3hE2FB1Cu3n6/vzND3C7afT0V2/QlU7Pmgr8sR
1gnJnu0NJT5SZfzcTsqwt8rFw9lQZ3HcvEcfNo6T5KUyyY7FGCNGR5H27nvoKOP3
ea1h7U80loPV40sGTI8jj963wa9LNHUrjHTK4wY+KMWECgZuD/fHeE9YPB9MTdff
lJ5bWCoQmuJddvTtC+X0tOAsCkxgdbbw6ieKqzep8H4gtUjerZD+V8uUdbtpr7IL
sWPoaqrrADMv9cZtDVj+pEtNIJ3mpfuHYFKSON9jy/uxygeFTfVzLu43RFreDp8=
=D15/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit introduced parse_protocol callback which should
extract the protocol number from the L2 header. Make all Ethernet
devices support it.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new optional header_ops callback called parse_protocol and a
wrapper function dev_parse_header_protocol, similar to dev_parse_header.
The new callback's purpose is to extract the protocol number from the L2
header, the format of which is known to the driver, but not to the upper
layers of the stack.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the socket was created with socket(AF_PACKET, SOCK_RAW, 0),
skb->protocol will be unset, __skb_flow_dissect() will fail, and
skb_probe_transport_header() will fall back to the offset_hint, making
the resulting skb_transport_offset incorrect.
If, however, there is no transport header in the packet,
transport_header shouldn't be set to an arbitrary value.
Fix it by leaving the transport offset unset if it couldn't be found, to
be explicit rather than to fill it with some wrong value. It changes the
behavior, but if some code relied on the old behavior, it would be
broken anyway, as the old one is incorrect.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rhashtable_walk_init function has been obsolete for more than
two years. This patch finally converts its last users over to
rhashtable_walk_enter and removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update element names and new fields according to D3.3 of
the HE spec.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018 REVmd of the spec introduces the max channel switch time
element which is optionally included in beacons/probes when there
is a channel switch / extended channel switch element.
The value represents the maximum delay between the time the AP
transmitted the last beacon in current channel and the expected
time of the first beacon in the new channel, in TU.
Parse the value and pass it to the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
GSO packets with vnet_hdr must conform to a small set of gso_types.
The below commit uses flow dissection to drop packets that do not.
But it has false positives when the skb is not fully initialized.
Dissection needs skb->protocol and skb->network_header.
Infer skb->protocol from gso_type as the two must agree.
SKB_GSO_UDP can use both ipv4 and ipv6, so try both.
Exclude callers for which network header offset is not known.
Fixes: d5be7f632b ("net: validate untrusted gso packets without csum offload")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull keys fixes from James Morris:
- Handle quotas better, allowing full quota to be reached.
- Fix the creation of shortcuts in the assoc_array internal
representation when the index key needs to be an exact multiple of
the machine word size.
- Fix a dependency loop between the request_key contruction record and
the request_key authentication key. The construction record isn't
really necessary and can be dispensed with.
- Set the timestamp on a new key rather than leaving it as 0. This
would ordinarily be fine - provided the system clock is never set to
a time before 1970
* 'fixes-v5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
keys: Timestamp new keys
keys: Fix dependency loop between construction record and auth key
assoc_array: Fix shortcut creation
KEYS: allow reaching the keys quotas exactly
Pull networking fixes from David Miller:
1) Fix suspend and resume in mt76x0u USB driver, from Stanislaw
Gruszka.
2) Missing memory barriers in xsk, from Magnus Karlsson.
3) rhashtable fixes in mac80211 from Herbert Xu.
4) 32-bit MIPS eBPF JIT fixes from Paul Burton.
5) Fix for_each_netdev_feature() on big endian, from Hauke Mehrtens.
6) GSO validation fixes from Willem de Bruijn.
7) Endianness fix for dwmac4 timestamp handling, from Alexandre Torgue.
8) More strict checks in tcp_v4_err(), from Eric Dumazet.
9) af_alg_release should NULL out the sk after the sock_put(), from Mao
Wenan.
10) Missing unlock in mac80211 mesh error path, from Wei Yongjun.
11) Missing device put in hns driver, from Salil Mehta.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
sky2: Increase D3 delay again
vhost: correctly check the return value of translate_desc() in log_used()
net: netcp: Fix ethss driver probe issue
net: hns: Fixes the missing put_device in positive leg for roce reset
net: stmmac: Fix a race in EEE enable callback
qed: Fix iWARP syn packet mac address validation.
qed: Fix iWARP buffer size provided for syn packet processing.
r8152: Add support for MAC address pass through on RTL8153-BD
mac80211: mesh: fix missing unlock on error in table_path_del()
net/mlx4_en: fix spelling mistake: "quiting" -> "quitting"
net: crypto set sk to NULL when af_alg_release.
net: Do not allocate page fragments that are not skb aligned
mm: Use fixed constant in page_frag_alloc instead of size + 1
tcp: tcp_v4_err() should be more careful
tcp: clear icsk_backoff in tcp_write_queue_purge()
net: mv643xx_eth: disable clk on error path in mv643xx_eth_shared_probe()
qmi_wwan: apply SET_DTR quirk to Sierra WP7607
net: stmmac: handle endianness in dwmac4_get_timestamp
doc: Mention MSG_ZEROCOPY implementation for UDP
mlxsw: __mlxsw_sp_port_headroom_set(): Fix a use of local variable
...
Passing the struct ptp_clock_info caps by parameter is passing over 130 bytes
of data by value on the stack. Optimize this by passing it by reference instead.
Also shinks the object code size:
Before:
text data bss dec hex filename
12596 2160 64 14820 39e4 drivers/ptp/ptp_qoriq.o
After:
text data bss dec hex filename
12567 2160 64 14791 39c7 drivers/ptp/ptp_qoriq.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the existing helpers for the Clause 22 registers add helper
mii_10gbt_stat_mod_linkmode_lpa_t.
Note that this helper is defined in linux/mdio.h, not like the
Clause 22 helpers in linux/mii.h. Reason is that the Clause 45 register
constants are defined in uapi/linux/mdio.h. And uapi/linux/mdio.h
includes linux/mii.h before defining the C45 register constants.
v2:
- remove helpers that don't have users in this series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for you net-next
tree:
1) Missing NFTA_RULE_POSITION_ID netlink attribute validation,
from Phil Sutter.
2) Restrict matching on tunnel metadata to rx/tx path, from wenxu.
3) Avoid indirect calls for IPV6=y, from Florian Westphal.
4) Add two indirections to prepare merger of IPV4 and IPV6 nat
modules, from Florian Westphal.
5) Broken indentation in ctnetlink, from Colin Ian King.
6) Patches to use struct_size() from netfilter and IPVS,
from Gustavo A. R. Silva.
7) Display kernel splat only once in case of racing to confirm
conntrack from bridge plus nfqueue setups, from Chieh-Min Wang.
8) Skip checksum validation for layer 4 protocols that don't need it,
patch from Alin Nastac.
9) Sparse warning due to symbol that should be static in CLUSTERIP,
from Wei Yongjun.
10) Add new toggle to disable SDP payload translation when media
endpoint is reachable though the same interface as the signalling
peer, from Alin Nastac.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
C45 configuration of 10/100 and multi-giga bit auto negotiation
advertisement is standardized. Configuration of 1000Base-T however
appears to be vendor specific. Move the generic code out of the
Marvell driver into the common phy-c45.c file.
v2:
- change function name to genphy_c45_an_config_aneg
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: use new helper linkmode_adv_to_mii_10gbt_adv_t and split patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper linkmode_adv_to_mii_10gbt_adv_t(), similar to
linkmode_adv_to_mii_adv_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull EFI fixes from Ingo Molnar:
"This tree reverts a GICv3 commit (which was broken) and fixes it in
another way, by adding a memblock build-time entries quirk for ARM64"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm: Revert "Defer persistent reservations until after paging_init()"
arm64, mm, efi: Account for GICv3 LPI tables in static memblock reserve table
Pull perf fixes from Ingo Molnar:
"Two fixes on the kernel side: fix an over-eager condition that failed
larger perf ring-buffer sizes, plus fix crashes in the Intel BTS code
for a corner case, found by fuzzing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix impossible ring-buffer sizes warning
perf/x86: Add check_period PMU callback
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-02-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) numerous libbpf API improvements, from Andrii, Andrey, Yonghong.
2) test all bpf progs in alu32 mode, from Jiong.
3) skb->sk access and bpf_sk_fullsock(), bpf_tcp_sock() helpers, from Martin.
4) support for IP encap in lwt bpf progs, from Peter.
5) remove XDP_QUERY_XSK_UMEM dead code, from Jan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-02-16
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix lockdep false positive in bpf_get_stackid(), from Alexei.
2) several AF_XDP fixes, from Bjorn, Magnus, Davidlohr.
3) fix narrow load from struct bpf_sock, from Martin.
4) mips JIT fixes, from Paul.
5) gso handling fix in bpf helpers, from Willem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 3b89ea9c59 ("net: Fix for_each_netdev_feature on Big endian")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bodong Wang says,
BlueField device is a multi-core ARM processor in a highly integrated
system on chip coupled with the ConnectX interconnect controller.
BlueField device can be presented in one out of two modes:
- SEPARATED_HOST: ARM processors as a separated and orthogonal host
like any other external host in the multi-host virtualization model.
- EMBEDDED_CPU: ARM processors as Embedded CPU (EC) and part of the
external hosts virtualization model.
While existing driver already supports the device on separated_host
mode, this patch series focus on the functionalities of embedded_cpu
mode.
On embedded_cpu mode, BlueField device exposes regular network
controller PCI function in the BlueField host(e.g, x86). However, a
separate PCI function called Embedded CPU Physical Function(ECPF) is
also added to the ARM host side, where standard Linux distributions is
able to run on the ARM cores. Depends on the NV configuration from
firmware, ECPF can be the e-switch manager and firmware pages supplier.
If ECPF is configured as e-switch manager and page supplier, it will
take over the responsibilities from the PF on BlueField host includes:
- Owns, controls and manages all e-switch parts, and takes e-switch
traffic by default. It also should perform ENABLE_HCA for the host
PF just like a PF does for its VFs.
- Provides and manages the ICM host memory required for the HCA to
store various contexts for itself, the PF and VFs belong the
e-switch it manages.
The PF on BlueField host side is still responsible for:
- Control its own permanent MAC.
- PCI and SRIOV configurations and perform ENABLE_HCA for its VFs.
The ECPF can also retrieve information about the external host it
controls, like host identifier, PCI BDF and number of virtual functions.
As these parameters may be changed dynamically, an event will be triggered
to the driver on ECPF side.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcZ2amAAoJEEg/ir3gV/o+lzMIALvLNUoD6pXi41MWsOwvmAHg
07mzg1N80Z66MCcFau40I8T3h9NLiRMzNtFrBNtxx+ruwKFUpAjJHjaU0sms0yQH
WVjr35vk4XsZyDPSCJ4g/hCQVlgCT/1tIUvPO0YM9hjhDuVa9mT4wEpucQRDu8bO
KfeXNXLDFnlWxjokhpSVj369ozh+LTv4Kzy0MBBbji97bG6MktGAT8uCimUy7wG0
7dlYimnZ1+iUD1/DZQadiLCUHUu/rTcnvF2+DcdG/nbSU8ydVLgj6vgtIfCYt4e5
kcQO5hmatnl0iJUA8GNpdHQwGjYytKneoGmIfbMAK4KjvFNF+3/8N4Bytoa5kzk=
=DgTl
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-02-15' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Support Mellanox BlueField SmartNIC (mlx5-updates-2019-02-15)
Bodong Wang says,
BlueField device is a multi-core ARM processor in a highly integrated
system on chip coupled with the ConnectX interconnect controller.
BlueField device can be presented in one out of two modes:
- SEPARATED_HOST: ARM processors as a separated and orthogonal host
like any other external host in the multi-host virtualization model.
- EMBEDDED_CPU: ARM processors as Embedded CPU (EC) and part of the
external hosts virtualization model.
While existing driver already supports the device on separated_host
mode, this patch series focus on the functionalities of embedded_cpu
mode.
On embedded_cpu mode, BlueField device exposes regular network
controller PCI function in the BlueField host(e.g, x86). However, a
separate PCI function called Embedded CPU Physical Function(ECPF) is
also added to the ARM host side, where standard Linux distributions is
able to run on the ARM cores. Depends on the NV configuration from
firmware, ECPF can be the e-switch manager and firmware pages supplier.
If ECPF is configured as e-switch manager and page supplier, it will
take over the responsibilities from the PF on BlueField host includes:
- Owns, controls and manages all e-switch parts, and takes e-switch
traffic by default. It also should perform ENABLE_HCA for the host
PF just like a PF does for its VFs.
- Provides and manages the ICM host memory required for the HCA to
store various contexts for itself, the PF and VFs belong the
e-switch it manages.
The PF on BlueField host side is still responsible for:
- Control its own permanent MAC.
- PCI and SRIOV configurations and perform ENABLE_HCA for its VFs.
The ECPF can also retrieve information about the external host it
controls, like host identifier, PCI BDF and number of virtual functions.
As these parameters may be changed dynamically, an event will be triggered
to the driver on ECPF side.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target, e.g.:
void __cold f(void) {}
void __alias("f") g(void);
diagnoses:
warning: 'g' specifies less restrictive attribute than
its target 'f': 'cold' [-Wmissing-attributes]
These patch series clean these new warnings. Most of them are caused
by the module_init/exit macros.
Link: https://lore.kernel.org/lkml/20190125104353.2791-1-labbott@redhat.com/
-----BEGIN PGP SIGNATURE-----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=FCFQ
-----END PGP SIGNATURE-----
Merge tag 'compiler-attributes-for-linus-v5.0-rc7' of git://github.com/ojeda/linux
Pull compiler attributes fixes from Miguel Ojeda:
"Clean the new GCC 9 -Wmissing-attributes warnings
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target, e.g.:
void __cold f(void) {}
void __alias("f") g(void);
diagnoses:
warning: 'g' specifies less restrictive attribute than
its target 'f': 'cold' [-Wmissing-attributes]
These patch series clean these new warnings. Most of them are caused
by the module_init/exit macros"
Link: https://lore.kernel.org/lkml/20190125104353.2791-1-labbott@redhat.com/
* tag 'compiler-attributes-for-linus-v5.0-rc7' of git://github.com/ojeda/linux:
include/linux/module.h: copy __init/__exit attrs to init/cleanup_module
Compiler Attributes: add support for __copy (gcc >= 9)
lib/crc32.c: mark crc32_le_base/__crc32c_le_base aliases as __pure
This reverts commit eff8962888, which
deferred the processing of persistent memory reservations to a point
where the memory may have already been allocated and overwritten,
defeating the purpose.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20190215123333.21209-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the irqchip and EFI code, we have what basically amounts to a quirk
to work around a peculiarity in the GICv3 architecture, which permits
the system memory address of LPI tables to be programmable only once
after a CPU reset. This means kexec kernels must use the same memory
as the first kernel, and thus ensure that this memory has not been
given out for other purposes by the time the ITS init code runs, which
is not very early for secondary CPUs.
On systems with many CPUs, these reservations could overflow the
memblock reservation table, and this was addressed in commit:
eff8962888 ("efi/arm: Defer persistent reservations until after paging_init()")
However, this turns out to have made things worse, since the allocation
of page tables and heap space for the resized memblock reservation table
itself may overwrite the regions we are attempting to reserve, which may
cause all kinds of corruption, also considering that the ITS will still
be poking bits into that memory in response to incoming MSIs.
So instead, let's grow the static memblock reservation table on such
systems so it can accommodate these reservations at an earlier time.
This will permit us to revert the above commit in a subsequent patch.
[ mingo: Minor cleanups. ]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20190215123333.21209-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Syzkaller again found a path to a kernel crash through bad gso input.
By building an excessively large packet to cause an skb field to wrap.
If VIRTIO_NET_HDR_F_NEEDS_CSUM was set this would have been dropped in
skb_partial_csum_set.
GSO packets that do not set checksum offload are suspicious and rare.
Most callers of virtio_net_hdr_to_skb already pass them to
skb_probe_transport_header.
Move that test forward, change it to detect parse failure and drop
packets on failure as those cleary are not one of the legitimate
VIRTIO_NET_HDR_GSO types.
Fixes: bfd5f4a3d6 ("packet: Add GSO/csum offload support.")
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).
This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ECPF connects to the eswitch through vport 0xfffe. ECPF may or may
not be the eswitch manager depending on firmware configuration.
1. If ECPF is eswitch manager: ECPF will take over the eswitch manager
responsibility. A rep of the host PF shall be created at the ECPF
side for the eswitch manager to control.
2. If ECPF is not eswitch manager: host PF will be the eswitch manager,
ECPF acts similar as a VF to the host PF. Host PF will be aware
of the ECPF vport presence and control it's rep.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In offloads mode, the current implementation puts the uplink
representor at index zero of the vport reps array. It is not "natural"
to place it at index 0 since we want to put the representor for vport
0 at index 0 with the introduction of SmartNIC. A separate patch will
handle the case whether a rep is needed for vport 0 (PF vport).
So, we want to have a different placeholder for uplink vport and
representor. It was placed at the end of vport and rep array. Since
vport number can no longer act as an index into the vport or
representors arrays, use functions to map vport numbers to indices
when accessing the vports or representors arrays, and vice versa.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eswitch has two users: IB and ETH. They both register repersentors
when mlx5 interface is added, and unregister the repersentors when
mlx5 interface is removed. Ideally, each driver should only deal with
the entities which are unique to itself. However, current IB and ETH
drivers have to perform the following eswitch operations:
1. When registering, specify how many vports to register. This number
is the same for both drivers which is the total available vport
numbers.
2. When unregistering, specify the number of registered vports to do
unregister. Also, unload the repersentors which are already loaded.
It's unnecessary for eswitch driver to hands out the control of above
operations to individual driver users, as they're not unique to each
driver. Instead, such operations should be centralized to eswitch
driver. This consolidates eswitch control flow, and simplified IB and
ETH driver.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the eswitch vport reps have a valid indicator, which is
set on register and unset on unregister. However, a rep can be loaded
or not loaded when doing unregister, current driver checks if the
vport of that rep is enabled as a flag to imply the rep is loaded.
However, for ECPF, this is not valid as the host PF will enable the
vports for its VFs instead.
Add three states: {unregistered, registered, loaded}, with the
following state changes across different operations:
create: (none) -> unregistered
reg: unregistered -> registered
load: registered -> loaded
unload: loaded -> registered
unreg: registered -> unregistered
Note that the state shall only be updated inside eswitch driver rather
than individual drivers such as ETH or IB.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When driver is entering offloads mode, there are two major tasks to
do: initialize flow steering and create representors. Flow steering
should make sure enough flow table/group spaces are reserved for all
reps. Representors will be created in a group, all or none.
With the introduction of ECPF, flow steering should still reserve the
same spaces. But, the representors are not always loaded/unloaded in a
single piece. Once ECPF is in offloads mode, it will get the number
of VF changing event from host PF. In such scenario, only the VF reps
should be loaded/unloaded, not the reps for special vports (such as
the uplink vport).
Thus, when entering offloads mode, driver should specify the total
number of reps, and the number of VF reps separately. When leaving
offloads mode, the cleanup should use the information self-contained
in eswitch such as number of VFs.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Commands referring to vports use the following scheme:
1. When referring to my own vport, put 0 in vport and 0 in other_vport.
2. When referring to another vport, put the vport number of the
referred vport and put 1 in other_vport. It was assumed that driver
is accessing other vport when vport number is greater than 0.
With the above scheme, the case that ECPF eswitch manager is trying
to access host PF vport will fall over with scheme 1 as the vport
number is 0. This is apparently wrong as driver is trying to refer
other vport.
As such usage can only happen in the eswitch context, change relevant
functions to provide other vport input properly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In SmartNIC mode, the eswitch manager is not necessarily the PF
(vport 0). Use a helper function to get the correct eswitch manager
vport number and cache on the eswitch instance for fast reference.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxime Chevallier