The ss pin of spi0 is the same as sck pin. According to the
visionfive 2 documentation, it should be pin 49 instead of 48.
Fixes: 74fb20c8f0 ("riscv: dts: starfive: Add spi node and pins configuration")
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Node uart0_pins should be sorted alphabetically.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
usb0 was disabled by mistake when merging, so enable it.
Fixes: e7c304c034 ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The Starfive VisionFive 2 has a 16MiB NOR flash, while the reserved-data
partition is declared starting at address 0x600000 with a size of
0x1000000. This causes the kernel to output the following warning:
[ 22.156589] mtd: partition "reserved-data" extends beyond the end of device "13010000.spi.0" -- size truncated to 0xa00000
It seems to be a confusion between the size of the partition and the end
address. Fix that by specifying the right size.
Fixes: 8384087a42 ("riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC")
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
T-Head:
Add a second minimal devicetree for the second board using the th1520
SoC, the BeagleV Ahead. As with the Lichee Pi 4a, this is sufficient
only for booting to a console, with work on the mmc, clocks and ethernet
sides of things under way. A relicense to a dual licence for the
existing devicetree files is also done, for good measure.
RISC-V Devicetrees for v6.6-pt2
StarFive:
Fix the sort order of some nodes that I resolved incorrectly during a
merge conflict.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZOCDsgAKCRB4tDGHoIJi
0mEDAQDc1z032ZsKJSE/WBV0R8hw47RZoP22xHCP3d38vDfP3wEAsF6Kc0U+t8TQ
6CNGHUNpEkVJIdj/wOL8Zk0gV/GdLAA=
=F146
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=3ypd
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.6-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.6 Part 2
T-Head:
Add a second minimal devicetree for the second board using the th1520
SoC, the BeagleV Ahead. As with the Lichee Pi 4a, this is sufficient
only for booting to a console, with work on the mmc, clocks and ethernet
sides of things under way. A relicense to a dual licence for the
existing devicetree files is also done, for good measure.
RISC-V Devicetrees for v6.6-pt2
StarFive:
Fix the sort order of some nodes that I resolved incorrectly during a
merge conflict.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.6-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
riscv: dts: starfive: fix jh7110 qspi sort order
Link: https://lore.kernel.org/r/20230819-unwieldy-railing-9bba2b176aa7@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The BeagleV Ahead single board computer uses the T-Head TH1520 SoC.
Add a minimal device tree to support basic uart/gpio/dmac drivers so
that a user can boot to a basic shell.
Link: https://beagleboard.org/beaglev-ahead
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Emil pointed out that "13010000 sorts after 12070000". Reshuffle the
entries to be in-order.
Reported-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZNiusAAKCRB4tDGHoIJi
0u5JAP90hKhmPTWqxdRpnFrWi83k9RX4J6k5LHrqyt3e0sZ0HAD+JNiv4i4j8fDv
fm7usmraq8B2zLaV/AFmj9kiqdx0JgU=
=AH1c
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=+tgF
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.6
StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: (26 commits)
riscv: dts: starfive: jh7110: Fix GMAC configuration
riscv: dts: starfive - Add hwrng node for JH7110 SoC
riscv: dts: starfive - Add crypto and DMA node for JH7110
riscv: dts: starfive: Add mmc nodes on VisionFive 2 board
riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060
riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC
riscv: dts: starfive: jh7110: add the node and pins configuration for tdm
riscv: dts: starfive: jh7110: add dma controller node
riscv: dts: starfive: Add spi node and pins configuration
riscv: dts: starfive: Add USB dts node for JH7110
riscv: dts: starfive: Add USB and PCIe PHY nodes for JH7110
riscv: dts: starfive: jh7110: Add temperature sensor node and thermal-zones
riscv: dts: starfive: jh7100: Add temperature sensor node and thermal-zones
riscv: dts: starfive: visionfive 2: Add configuration of gmac and phy
riscv: dts: starfive: jh7110: Add ethernet device nodes
riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node
riscv: dts: starfive: jh7110: Add syscon nodes
riscv: dts: starfive: jh7110: Add STGCRG/ISPCRG/VOUTCRG nodes
riscv: dts: starfive: jh7110: Add DVP and HDMI TX pixel external clocks
dt-bindings: clock: Add StarFive JH7110 Video-Output clock and reset generator
...
Link: https://lore.kernel.org/r/20230813-naturist-fragment-ac7d10c453ba@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Allwinner D1, T113 provide two CAN controllers that are variants
of the R40 controller.
I have tested support for these controllers on two boards:
- A Lichee Panel RV 86 Panel running a D1 chip
- A Mango Pi MQ Dual running a T113-s3 chip
Both of these fully support both CAN controllers.
Signed-off-by: John Watts <contact@jookia.org>
Link: https://lore.kernel.org/r/20230807191952.2019208-1-contact@jookia.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the mmc nodes for the StarFive JH7110 SoC.
Set mmc0 node to emmc and set mmc1 node to sd.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Enable DCDC1 node for vmmc-supply and enable ALDO4 node for
vqmmc-supply.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
This patch adds declaration of the general purpose ADC for D1
and T113s SoCs.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-5-bigunclemax@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add the tdm controller node and pins configuration of tdm for the
StarFive JH7110 SoC.
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Walker Chen <walker.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add USB and PCIe PHY dts nodes for the StarFive JH7110 SoC.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
dtbs_check w/ W=1 complains:
Warning (unit_address_vs_reg): /soc/ethernet@11c20000/ethernet-phy@7: node has a unit name, but no reg or ranges property
Warning (avoid_unnecessary_addr_size): /soc/ethernet@11c20000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
The ethernet@11c20000 node is guarded by an `#if (!SW_ET0_EN_N)` in
rzg2ul-smarc-som.dtsi, where the phy child node is added. In
rzfive-smarc-som.dtsi, the ethernet node is marked disabled & the
interrupt properties are deleted from the phy child node. As a result,
the produced dts looks like:
ethernet@11c20000 {
compatible = "renesas,r9a07g043-gbeth",
"renesas,rzg2l-gbeth";
/* snip */
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
ethernet-phy@7 {
};
};
Adding a corresponding `#if (!SW_ET0_EN_N)` around the node in
rzfive-smarc-som.dtsi avoids the complaint, as the empty child node is
not added:
ethernet@11c20000 {
compatible = "renesas,r9a07g043-gbeth",
"renesas,rzg2l-gbeth";
/* snip */
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230712-squealer-walmart-9587342ddec1@wendy
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add temperature sensor and thermal-zones support for
the StarFive JH7110 SoC. CPUFreq cooling is supported
in thermal-zones.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add temperature sensor and thermal-zones support for
the StarFive JH7100 SoC.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
v1.3B:
v1.3B uses motorcomm YT8531(rgmii-id phy) x2, need delay and
inverse configurations.
The tx_clk of v1.3B uses an external clock and needs to be
switched to an external clock source.
v1.2A:
v1.2A gmac0 uses motorcomm YT8531(rgmii-id) PHY, and needs delay
configurations.
v1.2A gmac1 uses motorcomm YT8512(rmii) PHY, and needs to
switch rx and rx to external clock sources.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
[conor: squashed a fix from Samin to use the actual properties]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add the '-@' DTC option for the starfive devices. This option
populates the '__symbols__' node that contains all the necessary symbols
for supporting device-tree overlays (for instance from the firmware or
the bootloader) on these devices.
The starfive devices allow various modules to be connected and this
enables users to create out-of-tree device-tree overlays for these modules.
Please note that this change does increase the size of the resulting DTB
by ~20%. For example, with v6.4 increase in size is as follows:
jh7100-beaglev-starlight.dtb 6192 -> 7339
jh7100-starfive-visionfive-v1.dtb 6281 -> 7428
jh7110-starfive-visionfive-2-v1.2a.dtb 11101 -> 13447
jh7110-starfive-visionfive-2-v1.3b.dtb 11101 -> 13447
Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
T-Head:
Add a basic dtsi, Kconfig bits & trivial binding additions for the T-Head
1520 SoC (codename "light"). This SoC can be found on the Lichee Pi 4a,
for which a minimal dts is added.
Misc:
Re-sort the dts Makefile to be in alphanumerical order by directory.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZJDOAwAKCRB4tDGHoIJi
0gAoAQCqGDPqdw5MdT/+tTJqkAIVFo3KyxSrMHvv3TE36Xp1HgEAxJQ+NoZ30nhx
pbaJaRcZDw7PKOVmMJ92R564EMdjngA=
=hJMo
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=U5qO
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.5-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.5 Part 2
T-Head:
Add a basic dtsi, Kconfig bits & trivial binding additions for the T-Head
1520 SoC (codename "light"). This SoC can be found on the Lichee Pi 4a,
for which a minimal dts is added.
Misc:
Re-sort the dts Makefile to be in alphanumerical order by directory.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
dt-bindings: riscv: Add T-HEAD TH1520 board compatibles
dt-bindings: timer: Add T-HEAD TH1520 clint
dt-bindings: interrupt-controller: Add T-HEAD's TH1520 PLIC
Link: https://lore.kernel.org/r/20230620-fidelity-variety-60b47c889e31@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZIdfVAAKCRB4tDGHoIJi
0mspAP4m1zrOWojsDmwpodCajBTW6PEtMAztxRUj/qeA4IEsYgEA+NI1DhrUkwZ6
K1vw1VzP56auVkdS3X7ZBhEpjfnkCg4=
=JA/v
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=NR4f
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.5
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: Add cpu scaling for JH7110 SoC
riscv: dts: starfive: Enable axp15060 pmic for cpufreq
dt-bindings: interrupt-controller: sifive,plic: Sort compatible values
dt-bindings: timer: sifive,clint: Clean up compatible value section
riscv: dts: starfive: jh7110: Add watchdog node
riscv: dts: starfive: jh7100: Add watchdog node
riscv: dts: starfive: Add PMU controller node
MAINTAINERS: exclude maintained subdirs in RISC-V misc DT entry
Link: https://lore.kernel.org/r/20230612-fasting-floss-0bc05a08bc7a@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New additions to the list have tried to respect alphanumeric ordering,
but the thing was out of order to start with. Sort it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Jisheng Zhang <jszhang@kernel.org> says:
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
This also pulls in -rc2, because of some maintainers re-jigging that
went on in the interim in commit 80e62bc848 ("MAINTAINERS: re-sort
all entries and fields").
Link: https://lore.kernel.org/r/20230617161529.2092-1-jszhang@kernel.org
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add initial device tree for the TH1520 RISC-V SoC by T-HEAD.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add the operating-points-v2 to support cpu scaling on StarFive JH7110 SoC.
It supports up to 4 cpu frequency loads.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The VisionFive 2 board has an embedded pmic axp15060,
which supports the cpu DVFS through the dcdc2 regulator.
This patch enables axp15060 pmic and configs the dcdc2.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Some boards form the MangoPi family (MQ\MQ-Dual\MQ-R) may have
an optional SPI flash that connects to the SPI0 controller.
This controller is the same for R329/D1/R528/T113s SoCs and
should be supported by the sun50i-r329-spi driver.
So let's add its DT nodes.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230510081121.3463710-6-bigunclemax@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add the pmu controller node for the StarFive JH7110 SoC. The PMU needs
to be used by other modules, e.g. VPU,ISP,etc.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Walker Chen <walker.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* Support for runtime detection of the Svnapot extension.
* Support for Zicboz when clearing pages.
* We've moved to GENERIC_ENTRY.
* Support for !MMU on rv32 systems.
* The linear region is now mapped via huge pages.
* Support for building relocatable kernels.
* Support for the hwprobe interface.
* Various fixes and cleanups throughout the tree.
-----BEGIN PGP SIGNATURE-----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=oxQd
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.4-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for runtime detection of the Svnapot extension
- Support for Zicboz when clearing pages
- We've moved to GENERIC_ENTRY
- Support for !MMU on rv32 systems
- The linear region is now mapped via huge pages
- Support for building relocatable kernels
- Support for the hwprobe interface
- Various fixes and cleanups throughout the tree
* tag 'riscv-for-linus-6.4-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (57 commits)
RISC-V: hwprobe: Explicity check for -1 in vdso init
RISC-V: hwprobe: There can only be one first
riscv: Allow to downgrade paging mode from the command line
dt-bindings: riscv: add sv57 mmu-type
RISC-V: hwprobe: Remove __init on probe_vendor_features()
riscv: Use --emit-relocs in order to move .rela.dyn in init
riscv: Check relocations at compile time
powerpc: Move script to check relocations at compile time in scripts/
riscv: Introduce CONFIG_RELOCATABLE
riscv: Move .rela.dyn outside of init to avoid empty relocations
riscv: Prepare EFI header for relocatable kernels
riscv: Unconditionnally select KASAN_VMALLOC if KASAN
riscv: Fix ptdump when KASAN is enabled
riscv: Fix EFI stub usage of KASAN instrumented strcmp function
riscv: Move DTB_EARLY_BASE_VA to the kernel address space
riscv: Rework kasan population functions
riscv: Split early and final KASAN population functions
riscv: Use PUD/P4D/PGD pages for the linear mapping
riscv: Move the linear mapping creation in its own function
riscv: Get rid of riscv_pfn_base variable
...
The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek, NXP,
Rockchips, Renesas, TI, Samsung and ST Microelectronics. These all
add new features for existing machines, as well as new machines and
SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V
based D1 chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core
like its JH7100 predecessor, but with additional CPU cores
and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini
gets added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs,
based on the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the
Snapdragon family.
Including the initial board support for the added SoC platforms,
there are 52 new machines. The largest group are 19 boards
industrial embedded boards based on the NXP i.MX6 (32-bit)
and i.MX8 (64-bit) families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three "Banana Pi" variants based on the Amlogic g12b
(A311D, S922X) SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs,
including the rk3588s-khadas-edge2 and a few NanoPi
models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete "oxnas"
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the Qualcomm
Sc7180 "trogdor" design that were never part of products.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmRGp0gACgkQYKtH/8kJ
UicqgQ//cOC0FIvvzNztCrMDDXcDtltGJl28iyR9Ld8PIQL2/xv58yJ5GqQmF38b
ZJSiRZL2TZ8nFG4/H19qirTkoAo3ryc1rcZM+hfxYsF8ikMh7hieUVgI5yo/+OaF
Mf/qlu+Usx4Gvr6Kv8fQN9UhJQFBQm2MYumlMvZDC9l7Q1HAgJfq6Hsx1dNZJ05Y
RwFk2bgeXze7o5gPwMPKzf88T+dfFBV7uNmPbFd8hAf//ZoMPlrvHt6kmmsVeoOk
JsLC5jllh/TbC4GjnYi3f9ipJwsFbp+r5y69IWNsOXBn28cDPJd8pUQtvoFa7fQ4
a3AgzXQM0Ns0cWwGqzHqm/rRX7Wr+Y57BqXUqP2JNCMGYdNO63i5KOE4gp/vbgxn
0WJGC/4oaPyeSqY90LoMTNpvMpNOBjIZCyzyljsrwHuLA3bl7jZWP63Bxc65VhYR
XQ6fKzW+Irz49gsyo6fiRhtZYgL+v310u9gigV7ahFrET6vu3K0QDdzbxWcF9cYi
BD6OqmlTVbrBSVnKtk1TfSI2IRC8zq+SH7zBN+97OuRnUFe94og83JdsQQI9bl/o
x2W/vedxcYaZrj5/1/mCjKskchJg3tvWExLs/0ZKCbol8lZ7RioSqg4EvLkkxF+0
2gXJ7pzfmjqxcoPd90jj8dpbb5SvStz1AErSgkoVehKeOErWGTw=
=j12m
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek,
NXP, Rockchips, Renesas, TI, Samsung and ST Microelectronics. These
all add new features for existing machines, as well as new machines
and SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V based D1
chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core like its
JH7100 predecessor, but with additional CPU cores and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini gets
added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs, based on
the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the Snapdragon
family.
Including the initial board support for the added SoC platforms, there
are 52 new machines. The largest group are 19 boards industrial
embedded boards based on the NXP i.MX6 (32-bit) and i.MX8 (64-bit)
families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three 'Banana Pi' variants based on the Amlogic g12b (A311D, S922X)
SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs, including
the rk3588s-khadas-edge2 and a few NanoPi models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete 'oxnas'
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the
Qualcomm Sc7180 'trogdor' design that were never part of products"
* tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (836 commits)
arm64: dts: rockchip: Add support for volume keys to rk3399-pinephone-pro
arm64: dts: rockchip: Add vdd_cpu_big regulators to rk3588-rock-5b
arm64: dts: rockchip: Use generic name for es8316 on Pinebook Pro and Rock 5B
arm64: dts: rockchip: Drop RTC clock-frequency on rk3588-rock-5b
arm64: dts: apple: t8112: Add PWM controller
arm64: dts: apple: t600x: Add PWM controller
arm64: dts: apple: t8103: Add PWM controller
arm64: dts: rockchip: Add pinctrl gpio-ranges for rk356x
ARM: dts: nomadik: Replace deprecated spi-gpio properties
ARM: dts: aspeed-g6: Add UDMA node
ARM: dts: aspeed: greatlakes: add mctp device
ARM: dts: aspeed: greatlakes: Add gpio names
ARM: dts: aspeed: p10bmc: Change power supply info
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMM050 Magnetometer
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMA255 Accelerometer
arm64: dts: mediatek: mt6795: Add tertiary PWM node
arm64: dts: rockchip: add panel to Anbernic RG353 series
dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC
dt-bindings: arm: fsl: Add chargebyte Tarragon
dt-bindings: vendor-prefixes: add chargebyte
...
To circumvent an issue where placing the relocations inside the init
sections produces empty relocations, use --emit-relocs. But to avoid
carrying those relocations in vmlinux, use an intermediate
vmlinux.relocs file which is a copy of vmlinux *before* stripping its
relocations.
Suggested-by: Björn Töpel <bjorn@kernel.org>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230329045329.64565-7-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Jisheng Zhang