When retransmitting due to T3 timeout, retransmit all the
in-flight chunks for the corresponding transport/path, including
chunks sent less then 1 rto ago.
This is the correct behaviour according to rfc4960 section 6.3.3
E3 and
"Note: Any DATA chunks that were sent to the address for which the
T3-rtx timer expired but did not fit in one MTU (rule E3 above)
should be marked for retransmission and sent as soon as cwnd
allows (normally, when a SACK arrives). ".
This fixes problems when more then one path is present and the T3
retransmission of the first chunk that timeouts stops the T3 timer
for the initial active path, leaving all the other in-flight
chunks waiting forever or until a new chunk is transmitted on the
same path and timeouts (and this will happen only if the cwnd
allows sending new chunks, but since cwnd was dropped to MTU by
the timeout => it will wait until the first heartbeat).
Example: 10 packets in flight, sent at 0.1 s intervals on the
primary path. The primary path is down and the first packet
timeouts. The first packet is retransmitted on another path, the
T3 timer for the primary path is stopped and cwnd is set to MTU.
All the other 9 in-flight packets will not be retransmitted
(unless more new packets are sent on the primary path which depend
on cwnd allowing it, and even in this case the 9 packets will be
retransmitted only after a new packet timeouts which even in the
best case would be more then RTO).
This commit reverts d0ce92910b and
also removes the now unused transport->last_rto, introduced in
b6157d8e03.
p.s The problem is not only when multiple paths are there. It
can happen in a single homed environment. If the application
stops sending data, it possible to have a hung association.
Signed-off-by: Andrei Pelinescu-Onciul <andrei@iptel.org>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently send window update SACKs every time we free up 1 PMTU
worth of data. That a lot more SACKs then necessary. Instead, we'll
now send back the actuall window every time we send a sack, and do
window-update SACKs when a fraction of the receive buffer has been
opened. The fraction is controlled with a sysctl.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When sctp_connectx() is used, we pick the first address as
primary, even though it may not have worked. This results
in excessive retransmits and poor performance. We should
select the address that the association was established with.
Reported-by: Thomas Dreibholz <dreibh@iem.uni-due.de>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
We currently set a_rwnd to 0 when faking a SACK from SHUTDOWN.
This results in an hung association if the remote only uses
SHUTDOWNs (which it's allowed to do) to acknowlege DATA when
closing. The reason for that is that we simply honor the a_rwnd
from the sack, but since we faked it to be 0, we enter 0-window
probing. The fix is to use the peers old rwnd and add our flight
size to it.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
SCTP RFC 4960 states that unacknowledged HEARTBEATS count as
errors agains a given transport or endpoint. As such, we
should increment the error counts for only for unacknowledged
HB, otherwise we detect failure too soon. This goes for both
the overall error count and the path error count.
Now, there is a difference in how the detection is done
between the two. The path error detection is done after
the increment, so to detect it properly, we actually need
to exceed the path threshold. The overall error detection
is done _BEFORE_ the increment. Thus to detect the failure,
it's enough for the error count to match the threshold.
This is why all the state functions use '>=' to detect failure,
while path detection uses '>'.
Thanks goes to Chunbo Luo <chunbo.luo@windriver.com> who first
proposed patches to fix this issue and made me re-read the spec
and the code to figure out how this cruft really works.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Currenlty, sctp breaks up user messages into fragments and
sends each fragment to the lower layer by itself. This means
that for each fragment we go all the way down the stack
and back up. This also discourages bundling of multiple
fragments when they can fit into a sigle packet (ex: due
to user setting a low fragmentation threashold).
We introduce a new command SCTP_CMD_SND_MSG and hand the
whole message down state machine. The state machine and
the side-effect parser will cork the queue, add all chunks
from the message to the queue, and then un-cork the queue
thus causing the chunks to get transmitted.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
RFC 5061 Section 5.1 ASCONF Chunk Procedures said:
B4) Re-transmit the ASCONF Chunk last sent and if possible choose an
alternate destination address (please refer to [RFC4960],
Section 6.4.1). An endpoint MUST NOT add new parameters to this
chunk; it MUST be the same (including its Sequence Number) as
the last ASCONF sent. An endpoint MAY, however, bundle an
additional ASCONF with new ASCONF parameters with the next
Sequence Number. For details, see Section 5.5.
This patch fix to choose an alternate destination address when
re-transmit the ASCONF chunk, with some dup codes cleanup.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Commit faee47cdbf
(sctp: Fix the RTO-doubling on idle-link heartbeats)
broke the RTO doubling for data retransmits. If the
heartbeat was sent before the data T3-rtx time, the
the RTO will not double upon the T3-rtx expiration.
Distingish between the operations by passing an argument
to the function.
Additionally, Wei Youngjun pointed out that our treatment
of requested HEARTBEATS and timer HEARTBEATS is the same
wrt resetting congestion window. That needs to be separated,
since user requested HEARTBEATS should not treat the link
as idle.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ERROR chunk is received with too many error causes in ESTABLISHED
state, the kernel get panic.
This is because sctp limit the max length of cmds to 14, but while
ERROR chunk is received, one error cause will add around 2 cmds by
sctp_add_cmd_sf(). So many error causes will fill the limit of cmds
and panic.
This patch fixed the problem.
This bug can be test by SCTP Conformance Test Suite
<http://networktest.sourceforge.net/>.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP incorrectly doubles rto ever time a Hearbeat chunk
is generated. However RFC 4960 states:
On an idle destination address that is allowed to heartbeat, it is
recommended that a HEARTBEAT chunk is sent once per RTO of that
destination address plus the protocol parameter 'HB.interval', with
jittering of +/- 50% of the RTO value, and exponential backoff of the
RTO if the previous HEARTBEAT is unanswered.
Essentially, of if the heartbean is unacknowledged, do we double the RTO.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tsn map currently use is 4K large and is stuck inside
the sctp_association structure making memory references REALLY
expensive. What we really need is at most 4K worth of bits
so the biggest map we would have is 512 bytes. Also, the
map is only really usefull when we have gaps to store and
report. As such, starting with minimal map of say 32 TSNs (bits)
should be enough for normal low-loss operations. We can grow
the map by some multiple of 32 along with some extra room any
time we receive the TSN which would put us outside of the map
boundry. As we close gaps, we can shift the map to rebase
it on the latest TSN we've seen. This saves 4088 bytes per
association just in the map alone along savings from the now
unnecessary structure members.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables cookie-echo retransmission transport switch
feature. If COOKIE-ECHO retransmission happens, it will be sent
to the address other than the one last sent to.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
RFC 4960, Section 11.4. Protection of Non-SCTP-Capable Hosts
When an SCTP stack receives a packet containing multiple control or
DATA chunks and the processing of the packet requires the sending of
multiple chunks in response, the sender of the response chunk(s) MUST
NOT send more than one packet. If bundling is supported, multiple
response chunks that fit into a single packet MAY be bundled together
into one single response packet. If bundling is not supported, then
the sender MUST NOT send more than one response chunk and MUST
discard all other responses. Note that this rule does NOT apply to a
SACK chunk, since a SACK chunk is, in itself, a response to DATA and
a SACK does not require a response of more DATA.
We implement this by not servicing our outqueue until we reach the end
of the packet. This enables maximum bundling. We also identify
'response' chunks and make sure that we only send 1 packet when sending
such chunks.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brings delayed_ack socket option set/get into line with the latest ietf
socket extensions API draft, while maintaining backwards compatibility.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'asoc' parameter to sctp_cmd_hb_timer_update() is unused, and
we can remove it.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing (almost) all invocations of list_for_each() with
list_for_each_entry() tightens up the code and allows for the deletion
of numerous list iterator variables that are no longer necessary.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an error length INIT-ACK during COOKIE-WAIT,
a 0-vtag ABORT will be responsed. This action violates the
protocol apparently. This patch achieves the following things.
1 If the INIT-ACK contains all the fixed parameters, use init-tag
recorded from INIT-ACK as vtag.
2 If the INIT-ACK doesn't contain all the fixed parameters,
just reflect its vtag.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was notified by Randy Stewart that lksctp claims to be
"the reference implementation". First of all, "the
refrence implementation" was the original implementation
of SCTP in usersapce written ty Randy and a few others.
Second, after looking at the definiton of 'reference implementation',
we don't really meet the requirements.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Commit d0ce92910b broke several retransmit
cases including fast retransmit. The reason is that we should
only delay by rto while doing retranmists as a result of a timeout.
Retransmit as a result of path mtu discover, fast retransmit, or
other evernts that should trigger immidiate retransmissions got broken.
Also, since rto is doubled prior to marking of packets elegable for
retransmission, we never marked correct chunks anyway.
The fix is provide a reason for a given retransmission so that we
can mark chunks appropriately and to save the old rto value to do
comparisons against.
All regressions tests passed with this code.
Spotted by Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Implement processing for the CHUNKS, RANDOM, and HMAC parameters and
deal with how this parameters are effected by association restarts.
In particular, during unexpeted INIT processing, we need to reply with
parameters from the original INIT chunk. Also, after restart, we need
to update the old association with new peer parameters and change the
association shared keys.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multi bundling SHUTDOWN-ACK message is received in ESTAB state,
this will cause "sctp protocol violation state" message print many times.
If SHUTDOWN-ACK is bundled 300 times in one packet, message will be
print 300 times. The same problem also exists when received unexpected
HEARTBEAT-ACK message which is bundled message times.
This patch used net_ratelimit() to suppress error messages print too fast.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When we recieve a FWD-TSN (meaning the peer has abandoned the data),
we need to clean up any partially received messages that may be
hanging out on the re-assembly or re-ordering queues. This is
a MUST requirement that was not properly done before.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com.>
During the INIT/COOKIE-ACK collision cases, it's possible to get
into a situation where the association id is not yet set at the time
of the user event generation. As a result, user events have an
association id set to 0 which will confuse applications.
This happens if we hit case B of duplicate cookie processing.
In the particular example found and provided by Oscar Isaula
<Oscar.Isaula@motorola.com>, flow looks like this:
A B
---- INIT-------> (lost)
<---------INIT------
---- INIT-ACK--->
<------ Cookie ECHO
When the Cookie Echo is received, we end up trying to update the
association that was created on A as a result of the (lost) INIT,
but that association doesn't have the ID set yet.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spring cleaning time...
There seems to be a lot of places in the network code that have
extra bogus semicolons after conditionals. Most commonly is a
bogus semicolon after: switch() { }
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As stated in the sctp socket api draft:
sac_info: variable
If the sac_state is SCTP_COMM_LOST and an ABORT chunk was received
for this association, sac_info[] contains the complete ABORT chunk as
defined in the SCTP specification RFC2960 [RFC2960] section 3.3.7.
We now save received ABORT chunks into the sac_info field and pass that
to the user.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a HEARTBEAT-ACK it's possible that the transport rto
timers will not be updated because a prior T3-RTX processing would
have cleared the rto_pending flag on the transport. However, if
we received a valid HEARTBEAT-ACK, we want to force update the
rto variables, so re-set the rto_pending flag before calling
sctp_transport_update_rto().
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when association enters SHUTDOWN state,the
implementation will SACK any DATA first and then transmit
the SHUTDOWN chunk. This is against the order required by
2960bis spec. SHUTDOWN must always be first, followed by
SACK. This change forces this order and also enables bundling.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instances of ->cmp_addr() are fine with switching both arguments
to net-endian; callers other than in sctp_cmp_addr_exact() (both
as ->cmp_addr(...) and direct calls of instances) adjusted;
sctp_cmp_addr_exact() switched to net-endian itself and adjustment
is done in its callers
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part 1: rename sctp_chunk->source, sctp_sockaddr_entry->a,
sctp_transport->ipaddr and sctp_transport->saddr (to ..._h)
The next patch will reintroduce these fields and keep them as
net-endian mirrors of the original (renamed) ones. Split in
two patches to make sure that we hadn't forgotten any instanes.
Later in the series we'll eliminate uses of host-endian variants
(basically switching users to net-endian counterparts as we
progress through that mess). Then host-endian ones will die.
Other embedded host-endian sctp_addr will be easier to switch
directly, so we leave them alone for now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
also always get __be16 protocol error; switch to SCTP_PERR()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
argument stored for SCTP_CMD_INIT_FAILED is always __be16
(protocol error). Introduced new field and accessor for
it (SCTP_PERR()); switched to their use (from SCTP_U32() and
.u32)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements Path Initialization procedure as described in
Sec 2.36 of RFC4460.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all the structure members that hold jiffies to be of type
unsigned long. This also corrects bad sysctl formating on 64 bit
architectures.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
This changes some simple "if (x) BUG();" statements to "BUG_ON(x);"
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to set/get heartbeat interval, maximum number of
retransmissions, pathmtu, sackdelay time for a particular transport/
association/socket as per the latest SCTP sockets api draft11.
Signed-off-by: Frank Filz <ffilz@us.ibm.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket level timeout values are maintained in sctp_sock and
association level timeouts are in sctp_association. So there is
no need for ep->timeouts.
Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds