Introduce mutual exclusion between the qla2xxx_remove_one PCI driver
callback and qla2x00_disable_board_on_pci_error, which is scheduled as
board_disable work by qla2x00_check_reg{32,16}_for_disconnect:
* Leave the driver-specific data attached to the underlying PCI device
intact in qla2x00_disable_board_on_pci_error, so that qla2x00_remove_one
has enough breadcrumbs to determine that any board_disable work has been
completed.
* In qla2xxx_remove_one, set a bit to prevent any subsequent
board_disable work from scheduling, then cancel and wait until pending
work has completed.
* Reuse the PCI device enable count check in qla2x00_remove_one to
determine if board_disable has occured. The original purpose of this
check was unnecessary since the driver remove function wasn't called
when the probe fails.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are various callers of qla2x00_check_reg{32,16}_for_disconnect
that may schedule board removal on PCI-disconnect. Test-and-set a
dedicated flag before scheduling board_disable so it is invoked only
once.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for T10-Dif for Target Mode to qla driver.
The driver will look for firmware attribute that support
this feature. When the feature is present, the capabilities
will be report to TCM layer.
Add CTIO CRC2 iocb to build T10-Dif commands.
Add support routines to process good & error cases.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For ISP27xx use the request/response queue index shadow registers
to avoid directly access them on the PCI bus.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the firmware cannot find the command specified then return SUCCESS to the
error handler so as not to needlessly escalate. Also cleanup the resources for
the command since we cannot expect the original command to returned in
interrupt context.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Allow for the capture of a firmware dump but have a sysfs node
(allow_cna_fw_dump) to allow the feature to be enabled/disabled dynamically.
The default is off.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
If we become disconnected from the PCI bus/PCIe fabric, there can be long delays
in register reads which can cause erroneous decisions to be made and cause a
soft lockup if a lock is held too long. As a preventative measure, check for a
disconnection (register reads that return -1) and then disable the board if we
find ourselves in this condition. For now, check in our interrupt handlers and
the per adapter one second timer.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver.
We now have to handle the aen so that other protocol drivers can use time
extension during some loopback operations.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla2x00_loopback_test() was hard setting the loopback iteration
count to 1 rather than obtaining it from the bsg request.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The original patch was not covering all the adapters and firmwares.
This commit reverts 3a11711ad0.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wait for the IDC complete AEN before returning the loopback operation back to
the application to make sure the port is put back into normal operations.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Give priority to I2C thermal.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Compiling qla_gs.o (part of the qla2xxx module) triggers two GCC
warnings:
drivers/scsi/qla2xxx/qla_gs.c: In function ‘qla2x00_fdmi_rhba’:
drivers/scsi/qla2xxx/qla_gs.c:1339:7: warning: array subscript is above array bounds [-Warray-bounds]
drivers/scsi/qla2xxx/qla_gs.c: In function ‘qla2x00_fdmi_register’:
drivers/scsi/qla2xxx/qla_gs.c:1663:15: warning: array subscript is above array bounds [-Warray-bounds]
It seems that the sequence of a strcpy followed by a strlen confuses GCC
when it is keeping track of array bounds here. (It is not clear to me
which array triggers this warning and by how much GCC thinks the
subscript is above its bounds. Neither is it clear to me why comparable
code in these two functions doesn't trigger this warning.)
An easy way to silence these warnings is to use preprocessor macros and
strncpy, as that apparently gives GCC enough information to keep track
of array bounds.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update the driver copyright from 2003-2011 to 2003-2012.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minor changes to support loopback functionality with ISP83xx CNAs.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Store used fcport loop_id's in a bitmap so that as opposed to looping through
all fcports to find the next free loop_id, new loop_id lookup can be just be
done via bitops.
[jejb: plus fix for incorrect LOOPID_MAP_SIZE from Andrew Vasquez]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add LLD target mode for >= 24xx series HW. This code was originally based on
external qla2x00t module based on 8.02.01-k4, and has been refactored to
push the bulk of code into mainline qla2xxx.ko LLD -> qla_target.c.
The implementation uses internal workqueues for I/O context submission
into tcm_qla2xxx code, and includes the struct qla_tgt_func_tmpl API for
external interaction to allow qla2xxx LDD to function without direct
target-core dependencies:
It also enables qla_target.c usage within existing qla2xxx LLD code.
This includes:
*) Addition of target mode specific members to existing data
structures in qla_def.h and struct qla_hw_data->tgt_ops using
qla_target.h:struct qla_tgt_func_tmpl
*) Addition of struct qla_tgt_func_tmpl and direct calls into
qla_target.c logic w/ qlt_* prefixed functions.
*) Addition of qla_iocb.c:qla2x00_req_pkt() for ring processing, and
qla2x00_issue_marker() for handling request/response queue processing
for target mode operation
*) Addition of various qla_tgt_mode_enabled() logic checks in
qla24xx_nvram_config(), qla2x00_initialize_adapter(), qla2x00_rff_id(),
qla2x00_abort_isp(), qla24xx_modify_vp_config(), and
qla2x00_vp_abort_isp().
By default the new qlini_mode module parameter is setting initiator-mode
to 'enabled' in order for 'modprobe qla2xxx' to continue to function as
expected in initiator only mode. Enabling target-mode operation will
currently require a:
modprobe qla2xxx qlini_mode="disabled"
in order to explictly disabled initiator mode and allow target-mode
to be enabled via tcm_qla2xxx configfs fabric callers.
(nab: Convert to qlini_mode='enabled' by default in qla_target.c)
(joern: Remove loop_id from qla_tgt_make_local_sess() arguments +
Remove unused s_id + fix s_id endianness bug +
simplify qla_tgt_abort_work)
(gerard: fix section __exit mismatch in qla_tgt_exit)
(arun: Capture ATIO queue during firmware dump + Send SCR in target mode +
Target mode review comments)
(roland: Don't create duplicate target sessions to address tearing down
ACLs with IO in flight + Add missing call to qlt_fc_port_deleted
call during qla2x00_schedule_rport_del timeout)
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The field vp_idx in struct fc_port is a redundant/mirror copy of
the same field in struct scsi_qla_host;
struct fc_port has a pointer vha to scsi_qla_host which allows
the original copy of vp_idx to be readily accessed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently stats is part of ha data structure, common for physical and virtual
ports. Moved the stats to vha, each port will have its own stat.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add a field to the qla_hw_data struct to allow us to set the maximum number of
fabric devices on a per adapter basis based on ISP type.
[jejb: fix up missing rval = QLA_SUCCESS to prevent uninit var warning]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rather than continuously allocating and freeing swl within the discovery
process, simply pre-allocate it the first time that it's needed, cache it
through the rest of the lifecycle of the driver and free it at module unload.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During rport tear-down, make sure we do an implicit LOGO of the fcport in our
firmware to try to clear any residual commands associated with that fcport.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of processing each RSCN individually, use only the name server results
from the switch to tell the existance of a given fcport.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rework the structures related to SRB processing to minimize the memory
allocations per I/O and manage resources associated with and completions
from common routines.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ISP2200 adapters only have 24 mailbox registers so read only that many.
Reported-by: Olatunji Ruwase <oor@cs.cmu.edu>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver should ensure there's a sufficient number of IOCBs
to satisfy the number of scatter-gather entries specified in the
command. Add a 'count' to the control structure, srb_ctx, to use
in qla2x00_alloc_iocbs().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add a new function to ISP specific pointers structure to take care of ISP
specific PCI IO space configuration.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch contains minor fixes to our new logging infrastructure:
- Remove extranous messages.
- Re-add 'nexus' and 'hdl' information.
- Adjusted the message ids to fill up the holes.
- Display FCP_CMND priority on update.
- Log only mail box error conditions.
- Do not print "Firmware ready **** FAILED ****" if cable is unplugged.
- Drop noisy 'fw_state...curr time...' message.
- Correct nexus display during abort.
- Add a special case error-logging set to '1'.
- Catagorize I/O exception display handling.
- Correct the bsg msg code printing.
- Dont use dynamic logging after host is removed.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minidump allows us to catpure a snapshot of the firmware/hardware states at the
time of failure for further analysis.
[jejb: added missing #include <linux/vmalloc.h>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fix:
- Disables app tag peeking; correct tag check will be added when the
SCSI API is available.
- Always derive ref_tag from scsi_get_lba()
- Removes incorrect swap of FCP_LUN in FCP_CMND
- Moves app-tag error check before ref-tag check. The reason being,
currently there is no interface in SCSI to retrieve the app-tag
for protection I/Os, so driver puts zero for app-tag in the
firmware interface, but requests not to validate it, but when a
ref-tag error is detected by firmware, it would put
expected/actual tags for all the protection tags (guard/app/ref).
As driver checks for app tag error first, a ref-tag error is
incorrectly flagged as app-tag error.
- Convert HBA specific checks to capability based.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the inline function qla2x00_set_port_state() so that when a fcport state
transition happens we can log the state transition if debug messages are
enabled.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Support is added for quiescence mode. This feature is for P3P
adapters. Any of the functions can put the firmware into quiescence
state. All the others have to ack that request. During quiescence mode
current commands are processed and all the new incoming I/Os are
blocked. Loop resync is performed after firmware comes out of
quiescence state.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_SHARED flag should not be set when calling request_irq for MSI
since this interrupt mechanism cannot be shared like standard INTx.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes the use of the port down retry counter as a mechanism to
update a fcport state. The internal driver counter is a residual carry-over
from pre-FC-transport aware driver inteaction. The ql2xport_down_retry module
parameter and NVRAM set ha->port_down_retry_count remain in order to seed the
fc-host's default dev-loss-tmo.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The sg table size is increased from 128 to 1024 to support multiple sg lists
and number of sg elements per scsi command.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In case the MPI times out, the FW issues an async event AE8002
to indicate this to every FCoE function. The FC/FCoE driver is
required to handle this, by doing a soft reset and issuing a
Write MPI register mailbox command to reset the MPI.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The default method that qla2xxx uses is the GID_PT nameserver command to
get a list of Nx_Ports. This patch adds a GFF_ID call for each port
returned by GID_PT to get the FC4 type. If the FC4 type is not FCP SCSI
then the qla2xxx driver will not record that port in it's port database.
For switches that do not support the GFF_ID command, the behavior will be
for qla2xxx to store that port anyways.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Outstanding mailbox commands, have no way to recover on f/w hung, and we
timeout on waiting for mbx response. This in turn affects the recovery process
as follows:
- We might already be in dpc while waiting for mbx to complete, so recovery for
that pci function will never get invoked. Reset Timeout (10 sec) is far less
than mbx timeout (30 sec).
- Other mbx cmds will get stuck due to serial mbx access.
Solution is to identify fw-hung scenario and handle outstanding mbx commands to
have an early-exit instead of waiting for response.
Other mbx commands waiting for access will also do an early-exit if fw-hung is
still applicable.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Used bootloder address from FLT while loading FW from flash as well.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hold a reference to the srb (sp) while aborting an I/O -- as the
I/O can/will complete from within the interrupt-context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1) Allow transition to NEED RESET state only from READY state for ISP82xx.
2) Avoid infinite ISP aborts when chip reset fails.
3) Code cleanup to remove some of the unused debug code.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently we can only issue the task management (TM)
commands via the mailbox mechanism. This is a limitation,
since only one mailbox command can be issued at a time.
The purpose of this effort is to provide support for
issuing and processing the respose to TM and Marker
IOCBs asynchronously. Towards achieving this, the
consolidated srb architecture that is currently used for
BSG and IOCB/Logio commands has been enhanced and used.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, BSG and IOCB/Logio commands have a different
framework (srb structs). The purpose of this effort is to
consolidate them into a generalized framework for these
as well as other asynchronous operations in the future.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver should not be unloaded if any application is using it.
To disallow driver unload, driver use count must be incremented.
Application uses this char device as handle and increases driver
use count to avoid possible driver unload.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enhanced the driver to support new FCoE host bus adapter.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. Segregate BSG interface specific code to new files.
2. Handle multiple vendor specific commands indepedently.
3. Reorganised support for reset, management and update FCoE firmware commands.
4. Fixed memory leak issue in Loopback.
5. Added new vendor command to support iiDMA using BSG interface.
6. Proper cleanup of dma mapped and dma allocated buffers for BSG request.
[jejb: fix up conflict and merge in Jiri Slaby lock imbalance patch]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver did not account for non-tape devices needing to employ
proper FCP2 recovery. Driver now checks the FCP2-capable flag
only, rather than using a midlayer-determined flag (TYPE_TAPE).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix to accommodate a hardware bug in multiqueue mode that does not
work properly when acknowledgement of MSIX Interrupts is disabled.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed the module parameters ql2xqfulltracking and ql2xqfullrampup
since the queue depth ramp up/down functionality is moved to scsi-ml.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In fabric-login based on iop BIT_8 firmware notifies presence of
a FCP2 device and not necessarily a TAPE device. So instead of
setting FCF_TAPE_PRESENT flag there we set it using
scsi_device->type after mid-layer scan recognises "type" of the
device.
It also adds a new flag FCF_FCP2_DEVICE for any future use.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ISPs which support this feature include 23xx and above.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Lay groundwork for adding alternative asynchronous operations by
generalize and extending the SRB structure. This allows for
follow-on patches to add support for:
- Asynchronous logins.
- ELS/CT passthru requests.
- Loopback requests.
- Non-blocking mailbox commands (ABTS, Task Management, etc).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the multiqueue mode fails to work, the driver falls back on single
queue mode. This ensures that the firmware is reinitialized with single
queue options and all the resources are readjusted accordingly.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On ppc64, gcc 4.4 spews lots of..
drivers/scsi/qla2xxx/qla_def.h:1485:7: warning: "__LITTLE_ENDIAN" is not defined
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Queued work processing will now be serialized with its own
lower-priority spinlock. This also simplifies the work-queue
interface for future work-queue consumers.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In case the onboard firmware is unable to be read or loaded for
operation, attempt to fallback to a limited-operational firmware
image stored in a different flash region. This will allow a user
to reflash and correct a board with proper operational firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware currently provides PB and PGF TLVs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cull and export VN_Port MAC address and VLAN_ID information on
supported FCoE ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As updates will occur using low-level option-rom manipulation
routines.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware semantics changed for 24xx and above ISPs in their
handling of the specified execution-throttle passed during
firmware initialization. The original codes use of a theoretical
maximum (0xffff, as carried over from earlier ISPs) could in fact
act as a throttle in some circumstances. Now set the value based
of the firmware's own 'resource' (exchange IOCBs) capabilities.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The original code to 'resize request-queues' based on iocb-counts
and employed during early ISP23xx testing was too
overly-pessimistic with regards to latencies in the firmware
pulling requests. Recent ISPs can easily keep up processing a
stream of commands from an abbreviated (effectively, half the
original size) queue.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rather than assuming a particular layout of the data. Applies to
recent ISPs only.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Interface allows for the update of onboard EDC firmware
present on mezzanine ISP25xx type cards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
General cleanup of extraneous/legacy crud.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ensure that an ISP-abort has completed before performing any
update. After the update do not wait for an ISP-abort completion,
instead just wait until the ISP is reset. This avoids long
delays due to waiting for loop ready in qla2x00_abort_isp().
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Given the low-level interface varies from one flash-part
manufacturer to the next, the Flash-Access-Control (FAC) mailbox
command makes the specific flash type transparent to the driver
by encapsulating a basic set of accessor and update routines.
Use these new routines where applicable by querying FAC opcode
get-sector-size at init-time.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reflects layout and format of latest specification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recent ISPs use this data to configure FCF information.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code used an overabundance of indirect pointers to
function helpers. Instead, the driver can exploit the immutable
properties of a queue's ISP-association and ID, which are both
known at queue initialization-time.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To ensure smooth operations amongst the FCoE and NIC side
components of the ISP81xx chip, the FCoE driver (qla2xxx) must
ensure the 10gb NIC driver (qlge) does not timeout waiting for
IDC (Inter-Driver Communication) acknowledgments. The
acknowledgment requirements are trivial -- a simple mirroring of
incoming mailbox registers during the AEN to a process-context
capable mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Codes to support new FCoE boards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would inadvertanly place I/Os on the default
request-queue. Also, correctly pass in the proper MSI-X vector
during response-queue initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In preparation for new ISP types with varying dump procedures.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ROMs in recent ISPs have MSI-X support, so it's no longer
necessary for the driver to fallback to interrupt polling during
ISP re-initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Software should not touch this region of flash, as the firmware
will be the only writer and consumer of the region.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Scan outstanding commands only in the queue where it is submitted
2. Update queue registers directly in the fast path
3. Queue specific BAR is remapped only for multiq capable adapters
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.
[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made to the qla2xxx FC driver in
preparation for the multi- queue and future SR IOV hardware.
1. scsi_qla_host structure has been changed to contain scsi host
specific data only.
2. A new structure, qla_hw_data is created to contain HBA specific
hardware data.
3. Request and response IO specific data strucures are created.
4. The global list of fcports for the hba is not maintained anymore,
instead a fcport list is construted on per scsi_qla_host.
Signed-of-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Joe Lawrence