Commit:
129766708 ("x86/efi: Only map RAM into EFI page tables if in mixed-mode")
stopped creating 1:1 mappings for all RAM, when running in native 64-bit mode.
It turns out though that there are 64-bit EFI implementations in the wild
(this particular problem has been reported on a Lenovo Yoga 710-11IKB),
which still make use of the first physical page for their own private use,
even though they explicitly mark it EFI_CONVENTIONAL_MEMORY in the memory
map.
In case there is no mapping for this particular frame in the EFI pagetables,
as soon as firmware tries to make use of it, a triple fault occurs and the
system reboots (in case of the Yoga 710-11IKB this is very early during bootup).
Fix that by always mapping the first page of physical memory into the EFI
pagetables. We're free to hand this page to the BIOS, as trim_bios_range()
will reserve the first page and isolate it away from memory allocators anyway.
Note that just reverting 129766708 alone is not enough on v4.9-rc1+ to fix the
regression on affected hardware, as this commit:
ab72a27da ("x86/efi: Consolidate region mapping logic")
later made the first physical frame not to be mapped anyway.
Reported-by: Hanka Pavlikova <hanka@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vojtech Pavlik <vojtech@ucw.cz>
Cc: Waiman Long <waiman.long@hpe.com>
Cc: linux-efi@vger.kernel.org
Cc: stable@kernel.org # v4.8+
Fixes: 129766708 ("x86/efi: Only map RAM into EFI page tables if in mixed-mode")
Link: http://lkml.kernel.org/r/20170127222552.22336-1-matt@codeblueprint.co.uk
[ Tidied up the changelog and the comment. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- unwinder fixes
- AMD CPU topology enumeration fixes
- microcode loader fixes
- x86 embedded platform fixes
- fix for a bootup crash that may trigger when clearcpuid= is used
with invalid values"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mpx: Use compatible types in comparison to fix sparse error
x86/tsc: Add the Intel Denverton Processor to native_calibrate_tsc()
x86/entry: Fix the end of the stack for newly forked tasks
x86/unwind: Include __schedule() in stack traces
x86/unwind: Disable KASAN checks for non-current tasks
x86/unwind: Silence warnings for non-current tasks
x86/microcode/intel: Use correct buffer size for saving microcode data
x86/microcode/intel: Fix allocation size of struct ucode_patch
x86/microcode/intel: Add a helper which gives the microcode revision
x86/microcode: Use native CPUID to tickle out microcode revision
x86/CPU: Add native CPUID variants returning a single datum
x86/boot: Add missing declaration of string functions
x86/CPU/AMD: Fix Bulldozer topology
x86/platform/intel-mid: Rename 'spidev' to 'mrfld_spidev'
x86/cpu: Fix typo in the comment for Anniedale
x86/cpu: Fix bootup crashes by sanitizing the argument of the 'clearcpuid=' command-line option
Some machines, such as the Lenovo ThinkPad W541 with firmware GNET80WW
(2.28), include memory map entries with phys_addr=0x0 and num_pages=0.
These machines fail to boot after the following commit,
commit 8e80632fb2 ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
Fix this by removing such bogus entries from the memory map.
Furthermore, currently the log output for this case (with efi=debug)
looks like:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[0x0000000000000000-0xffffffffffffffff] (0MB)
This is clearly wrong, and also not as informative as it could be. This
patch changes it so that if we find obviously invalid memory map
entries, we print an error and skip those entries. It also detects the
display of the address range calculation overflow, so the new output is:
[ 0.000000] efi: [Firmware Bug]: Invalid EFI memory map entries:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[0x0000000000000000-0x0000000000000000] (invalid)
It also detects memory map sizes that would overflow the physical
address, for example phys_addr=0xfffffffffffff000 and
num_pages=0x0200000000000001, and prints:
[ 0.000000] efi: [Firmware Bug]: Invalid EFI memory map entries:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[phys_addr=0xfffffffffffff000-0x20ffffffffffffffff] (invalid)
It then removes these entries from the memory map.
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[ardb: refactor for clarity with no functional changes, avoid PAGE_SHIFT]
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
[Matt: Include bugzilla info in commit log]
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=191121
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With the following commit:
4bc9f92e64 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
... efi_bgrt_init() calls into the memblock allocator through
efi_mem_reserve() => efi_arch_mem_reserve() *after* mm_init() has been called.
Indeed, KASAN reports a bad read access later on in efi_free_boot_services():
BUG: KASAN: use-after-free in efi_free_boot_services+0xae/0x24c
at addr ffff88022de12740
Read of size 4 by task swapper/0/0
page:ffffea0008b78480 count:0 mapcount:-127
mapping: (null) index:0x1 flags: 0x5fff8000000000()
[...]
Call Trace:
dump_stack+0x68/0x9f
kasan_report_error+0x4c8/0x500
kasan_report+0x58/0x60
__asan_load4+0x61/0x80
efi_free_boot_services+0xae/0x24c
start_kernel+0x527/0x562
x86_64_start_reservations+0x24/0x26
x86_64_start_kernel+0x157/0x17a
start_cpu+0x5/0x14
The instruction at the given address is the first read from the memmap's
memory, i.e. the read of md->type in efi_free_boot_services().
Note that the writes earlier in efi_arch_mem_reserve() don't splat because
they're done through early_memremap()ed addresses.
So, after memblock is gone, allocations should be done through the "normal"
page allocator. Introduce a helper, efi_memmap_alloc() for this. Use
it from efi_arch_mem_reserve(), efi_free_boot_services() and, for the sake
of consistency, from efi_fake_memmap() as well.
Note that for the latter, the memmap allocations cease to be page aligned.
This isn't needed though.
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.9
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 4bc9f92e64 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
Link: http://lkml.kernel.org/r/20170105125130.2815-1-nicstange@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current implementation supports only Intel Merrifield platforms. Don't mess
with the rest of the Intel MID family by not registering device with wrong
properties.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170102092450.87229-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
__printf() attributes help detecting issues in printf() format strings at
compile time.
Even though imr_selftest.c is only compiled with
CONFIG_DEBUG_IMR_SELFTEST=y, GCC complains about a missing format
attribute when compiling allmodconfig with -Wmissing-format-attribute.
Silence this warning by adding the attribute.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161219132144.4108-1-nicolas.iooss_linux@m4x.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Intel Mid goes in and creates a I2C device for the
MPU3050 if the input driver for MPU-3050 is activated.
As of commit:
3904b28efb ("iio: gyro: Add driver for the MPU-3050 gyroscope")
.. there is a proper and fully featured IIO driver for this
device, so deprecate the use of the incomplete input driver
by augmenting the device population code to react to the
presence of the IIO driver's Kconfig symbol instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1481722794-4348-1-git-send-email-linus.walleij@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move and add registration for the mlx-platform driver. Introduce button and lid
drivers for the surface3 (different from the surface3-pro). Add BXT PMIC TMU
support. Add Y700 to existing ideapad-laptop quirk.
ideapad-laptop:
- Add Y700 15-ACZ to no_hw_rfkill DMI list
surface3_button:
- Introduce button support for the Surface 3
surface3-wmi:
- Add custom surface3 platform device for controlling LID
- Balance locking on error path
mlx-platform:
- Add mlxcpld-hotplug driver registration
- Fix semicolon.cocci warnings
- Move module from arch/x86
platform/x86:
- Add Whiskey Cove PMIC TMU support
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYVxXxAAoJEKbMaAwKp364mDAIAL750zoO/liY1qfFGktkY2zS
xknJqh4UeIVW6iN9hEq7jQD3jkFl7hNuXgFyogLZgJQge8gfufsOD7ljkhp2wVF2
3Ir437f4GdcUeuhO6PwuPZnn++Y6oH2rLZc1d+5anZRikW470tnXitrXs5hsqG57
74KiSFa+v+Uj1kqU4Gjt0QDSfmQc185Wn5xieHPpZrcjDaut+N4t06+MDMcH7fjk
6nJ+tvo/dreZojA+AklljaNB2BioIGbEOGamnxOJ9Rjs0jV2d0A1c/6XBHDe+Xtu
SkWqvjdrLOSxAjErBpB97VYnYihjCDXfl+DIABOdumGO6hJz01DvbZ+VVLwGM0E=
=YH31
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.10-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull more x86 platform driver updates from Darren Hart:
"Move and add registration for the mlx-platform driver. Introduce
button and lid drivers for the surface3 (different from the
surface3-pro). Add BXT PMIC TMU support. Add Y700 to existing
ideapad-laptop quirk.
Summary:
ideapad-laptop:
- Add Y700 15-ACZ to no_hw_rfkill DMI list
surface3_button:
- Introduce button support for the Surface 3
surface3-wmi:
- Add custom surface3 platform device for controlling LID
- Balance locking on error path
mlx-platform:
- Add mlxcpld-hotplug driver registration
- Fix semicolon.cocci warnings
- Move module from arch/x86
platform/x86:
- Add Whiskey Cove PMIC TMU support"
* tag 'platform-drivers-x86-v4.10-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: surface3-wmi: Balance locking on error path
platform/x86: Add Whiskey Cove PMIC TMU support
platform/x86: ideapad-laptop: Add Y700 15-ACZ to no_hw_rfkill DMI list
platform/x86: Introduce button support for the Surface 3
platform/x86: Add custom surface3 platform device for controlling LID
platform/x86: mlx-platform: Add mlxcpld-hotplug driver registration
platform/x86: mlx-platform: Fix semicolon.cocci warnings
platform/x86: mlx-platform: Move module from arch/x86
Pull timer updates from Thomas Gleixner:
"This is the last functional update from the tip tree for 4.10. It got
delayed due to a newly reported and anlyzed variant of BIOS bug and
the resulting wreckage:
- Seperation of TSC being marked realiable and the fact that the
platform provides the TSC frequency via CPUID/MSRs and making use
for it for GOLDMONT.
- TSC adjust MSR validation and sanitizing:
The TSC adjust MSR contains the offset to the hardware counter. The
sum of the adjust MSR and the counter is the TSC value which is
read via RDTSC.
On at least two machines from different vendors the BIOS sets the
TSC adjust MSR to negative values. This happens on cold and warm
boot. While on cold boot the offset is a few milliseconds, on warm
boot it basically compensates the power on time of the system. The
BIOSes are not even using the adjust MSR to set all CPUs in the
package to the same offset. The offsets are different which renders
the TSC unusable,
What's worse is that the TSC deadline timer has a HW feature^Wbug.
It malfunctions when the TSC adjust value is negative or greater
equal 0x80000000 resulting in silent boot failures, hard lockups or
non firing timers. This looks like some hardware internal 32/64bit
issue with a sign extension problem. Intel has been silent so far
on the issue.
The update contains sanity checks and keeps the adjust register
within working limits and in sync on the package.
As it looks like this disease is spreading via BIOS crapware, we
need to address this urgently as the boot failures are hard to
debug for users"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Limit the adjust value further
x86/tsc: Annotate printouts as firmware bug
x86/tsc: Force TSC_ADJUST register to value >= zero
x86/tsc: Validate TSC_ADJUST after resume
x86/tsc: Validate cpumask pointer before accessing it
x86/tsc: Fix broken CONFIG_X86_TSC=n build
x86/tsc: Try to adjust TSC if sync test fails
x86/tsc: Prepare warp test for TSC adjustment
x86/tsc: Move sync cleanup to a safe place
x86/tsc: Sync test only for the first cpu in a package
x86/tsc: Verify TSC_ADJUST from idle
x86/tsc: Store and check TSC ADJUST MSR
x86/tsc: Detect random warps
x86/tsc: Use X86_FEATURE_TSC_ADJUST in detect_art()
x86/tsc: Finalize the split of the TSC_RELIABLE flag
x86/tsc: Set TSC_KNOWN_FREQ and TSC_RELIABLE flags on Intel Atom SoCs
x86/tsc: Mark Intel ATOM_GOLDMONT TSC reliable
x86/tsc: Mark TSC frequency determined by CPUID as known
x86/tsc: Add X86_FEATURE_TSC_KNOWN_FREQ flag
Since mlx-platform is not an architectural driver, it is moved out
of arch/x86/platform to drivers/platform/x86.
Relevant Makefile and Kconfig are updated.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Here's the tty/serial patchset for 4.10-rc1.
It's been a quiet kernel cycle for this subsystem, just a small number
of changes. A few new serial drivers, and some cleanups to the old
vgacon logic, and other minor serial driver changes as well.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAwDQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylcngCgko5+aPLnHENLNIaHhHlfdMbhy+EAn2H8wkzY
bEf+BG4CJDb6nZWERcUQ
=STpQ
-----END PGP SIGNATURE-----
Merge tag 'tty-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the tty/serial patchset for 4.10-rc1.
It's been a quiet kernel cycle for this subsystem, just a small number
of changes. A few new serial drivers, and some cleanups to the old
vgacon logic, and other minor serial driver changes as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (54 commits)
serial: 8250_mid fix calltrace when hotplug 8250 serial controller
console: Move userspace I/O out of console_lock to fix lockdep warning
tty: nozomi: avoid sprintf buffer overflow
serial: 8250_pci: Detach low-level driver during PCI error recovery
serial: core: don't check port twice in a row
mxs-auart: count FIFO overrun errors
serial: 8250_dw: Add support for IrDA SIR mode
serial: 8250: Expose set_ldisc function
serial: 8250: Add IrDA to UART capabilities
serial: 8250_dma: power off device after TX is done
serial: 8250_port: export serial8250_rpm_{get|put}_tx()
serial: sunsu: Free memory when probe fails
serial: sunhv: Free memory when remove() is called
vt: fix Scroll Lock LED trigger name
tty: typo in comments in drivers/tty/vt/keyboard.c
tty: amba-pl011: Add earlycon support for SBSA UART
tty: nozomi: use permission-specific DEVICE_ATTR variants
tty: serial: Make the STM32 serial port depend on it's arch
serial: ifx6x60: Free memory when probe fails
serial: ioc4_serial: Free memory when kzalloc fails during probe
...
Pull x86 platform updates from Ingo Molnar:
"Two changes:
- implement various VMWare guest OS improvements/fixes (Alexey
Makhalov)
- unexport a spurious export from the intel-mid platform driver
(Lukas Wunner)"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vmware: Add paravirt sched clock
x86/vmware: Add basic paravirt ops support
x86/vmware: Use tsc_khz value for calibrate_cpu()
x86/platform/intel-mid: Unexport intel_mid_pci_set_power_state()
x86/vmware: Read tsc_khz only once at boot time
Pull x86 idle updates from Ingo Molnar:
"There were two bigger changes in this development cycle:
- remove idle notifiers:
32 files changed, 74 insertions(+), 803 deletions(-)
These notifiers were of questionable value and the main usecase,
the i7300 driver, was essentially unmaintained and can be removed,
plus modern power management concepts don't need the callback - so
use this golden opportunity and get rid of this opaque and fragile
callback from a latency sensitive code path.
(Len Brown, Thomas Gleixner)
- improve the AMD Erratum 400 workaround that used high overhead MSR
polling in the idle loop (Borisla Petkov, Thomas Gleixner)"
* 'x86-idle-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove empty idle.h header
x86/amd: Simplify AMD E400 aware idle routine
x86/amd: Check for the C1E bug post ACPI subsystem init
x86/bugs: Separate AMD E400 erratum and C1E bug
x86/cpufeature: Provide helper to set bugs bits
x86/idle: Remove enter_idle(), exit_idle()
x86: Remove x86_test_and_clear_bit_percpu()
x86/idle: Remove is_idle flag
x86/idle: Remove idle_notifier
i7300_idle: Remove this driver
Pull x86 asm updates from Ingo Molnar:
"The main changes in this development cycle were:
- a large number of call stack dumping/printing improvements: higher
robustness, better cross-context dumping, improved output, etc.
(Josh Poimboeuf)
- vDSO getcpu() performance improvement for future Intel CPUs with
the RDPID instruction (Andy Lutomirski)
- add two new Intel AVX512 features and the CPUID support
infrastructure for it: AVX512IFMA and AVX512VBMI. (Gayatri Kammela,
He Chen)
- more copy-user unification (Borislav Petkov)
- entry code assembly macro simplifications (Alexander Kuleshov)
- vDSO C/R support improvements (Dmitry Safonov)
- misc fixes and cleanups (Borislav Petkov, Paul Bolle)"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
scripts/decode_stacktrace.sh: Fix address line detection on x86
x86/boot/64: Use defines for page size
x86/dumpstack: Make stack name tags more comprehensible
selftests/x86: Add test_vdso to test getcpu()
x86/vdso: Use RDPID in preference to LSL when available
x86/dumpstack: Handle NULL stack pointer in show_trace_log_lvl()
x86/cpufeatures: Enable new AVX512 cpu features
x86/cpuid: Provide get_scattered_cpuid_leaf()
x86/cpuid: Cleanup cpuid_regs definitions
x86/copy_user: Unify the code by removing the 64-bit asm _copy_*_user() variants
x86/unwind: Ensure stack grows down
x86/vdso: Set vDSO pointer only after success
x86/prctl/uapi: Remove #ifdef for CHECKPOINT_RESTORE
x86/unwind: Detect bad stack return address
x86/dumpstack: Warn on stack recursion
x86/unwind: Warn on bad frame pointer
x86/decoder: Use stderr if insn sanity test fails
x86/decoder: Use stdout if insn decoder test is successful
mm/page_alloc: Remove kernel address exposure in free_reserved_area()
x86/dumpstack: Remove raw stack dump
...
One include less is always a good thing(tm). Good riddance.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-6-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix:
arch/x86/platform/olpc/olpc-xo15-sci.c:199:12: warning: ‘xo15_sci_resume’
defined but not used [-Wunused-function]
static int xo15_sci_resume(struct device *dev)
^
which I see in randconfig builds here.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161126142706.13602-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rename the watchdog platform library file to explicitly show that is used only
on Intel Merrifield platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161118172723.179761-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Watchdog device in Intel Tangier relies on SCU to be present. It uses the SCU
IPC channel to send commands and receive responses. If watchdog driver is
initialized quite before SCU and a command has been sent the result is always
an error like the following:
intel_mid_wdt: Error stopping watchdog: 0xffffffed
Register watchdog device whne SCU is ready to avoid described issue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161118165224.175514-1-andriy.shevchenko@linux.intel.com
[ Small cleanups. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
TSC on Intel Atom SoCs capable of determining TSC frequency by MSR is
reliable and the frequency is known (provided by HW).
On these platforms PIT/HPET is generally not available so calibration won't
work at all and there is no other clocksource to act as a watchdog for the
TSC, so we have no other choice than to trust it.
Set both X86_FEATURE_TSC_KNOWN_FREQ and X86_FEATURE_TSC_RELIABLE flags to
make sure the calibration is skipped and no watchdog is required.
Signed-off-by: Bin Gao <bin.gao@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1479241644-234277-5-git-send-email-bin.gao@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add an IrDA UART capability flag and change the type of
uart_8250_port.capabilities to be u32 rather than unsigned short to
accommodate the additional flag.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- fix an Intel/MID boot crash/hang bug
- fix a cache topology mis-parsing bug on certain AMD CPUs
- fix a virtualization firmware bug by adding a check+quirk
workaround on the kernel side"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Deal with broken firmware (VMWare/XEN)
x86/cpu/AMD: Fix cpu_llc_id for AMD Fam17h systems
x86/platform/intel-mid: Retrofit pci_platform_pm_ops ->get_state hook
Booting an EFI mixed mode kernel has been crashing since commit:
e37e43a497 ("x86/mm/64: Enable vmapped stacks (CONFIG_HAVE_ARCH_VMAP_STACK=y)")
The user-visible effect in my test setup was the kernel being unable
to find the root file system ramdisk. This was likely caused by silent
memory or page table corruption.
Enabling CONFIG_DEBUG_VIRTUAL=y immediately flagged the thunking code as
abusing virt_to_phys() because it was passing addresses that were not
part of the kernel direct mapping.
Use the slow version instead, which correctly handles all memory
regions by performing a page table walk.
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112210424.5157-3-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix this when building on 32-bit:
arch/x86/platform/efi/efi.c: In function ‘__efi_enter_virtual_mode’:
arch/x86/platform/efi/efi.c:911:5: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(efi_memory_desc_t *)pa);
^
arch/x86/platform/efi/efi.c:918:5: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(efi_memory_desc_t *)pa);
^
The @pa local variable is declared as phys_addr_t and that is a u64 when
CONFIG_PHYS_ADDR_T_64BIT=y. (The last is enabled on 32-bit on a PAE
build.)
However, its value comes from __pa() which is basically doing pointer
arithmetic and checking, and returns unsigned long as it is the native
pointer width.
So let's use an unsigned long too. It should be fine to do so because
the later users cast it to a pointer too.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112210424.5157-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit cc7cc02bad ("PCI: Query platform firmware for device power
state") augmented struct pci_platform_pm_ops with a ->get_state hook and
implemented it for acpi_pci_platform_pm, the only pci_platform_pm_ops
existing till v4.7.
However v4.8 introduced another pci_platform_pm_ops for Intel Mobile
Internet Devices with commit 5823d0893e ("x86/platform/intel-mid: Add
Power Management Unit driver"). It is missing the ->get_state hook,
which is fatal since pci_set_platform_pm() enforces its presence. Andy
Shevchenko reports that without the present commit, such a device
"crashes without even a character printed out on serial console and
reboots (since watchdog)".
Retrofit mid_pci_platform_pm with the missing callback to fix the
breakage.
Acked-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: cc7cc02bad ("PCI: Query platform firmware for device power state")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/7c1567d4c49303a4aada94ba16275cbf56b8976b.1477221514.git.lukas@wunner.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Printing kernel text addresses in stack dumps is of questionable value,
especially now that address randomization is becoming common.
It can be a security issue because it leaks kernel addresses. It also
affects the usefulness of the stack dump. Linus says:
"I actually spend time cleaning up commit messages in logs, because
useless data that isn't actually information (random hex numbers) is
actively detrimental.
It makes commit logs less legible.
It also makes it harder to parse dumps.
It's not useful. That makes it actively bad.
I probably look at more oops reports than most people. I have not
found the hex numbers useful for the last five years, because they are
just randomized crap.
The stack content thing just makes code scroll off the screen etc, for
example."
The only real downside to removing these addresses is that they can be
used to disambiguate duplicate symbol names. However such cases are
rare, and the context of the stack dump should be enough to be able to
figure it out.
There's now a 'faddr2line' script which can be used to convert a
function address to a file name and line:
$ ./scripts/faddr2line ~/k/vmlinux write_sysrq_trigger+0x51/0x60
write_sysrq_trigger+0x51/0x60:
write_sysrq_trigger at drivers/tty/sysrq.c:1098
Or gdb can be used:
$ echo "list *write_sysrq_trigger+0x51" |gdb ~/k/vmlinux |grep "is in"
(gdb) 0xffffffff815b5d83 is in driver_probe_device (/home/jpoimboe/git/linux/drivers/base/dd.c:378).
(But note that when there are duplicate symbol names, gdb will only show
the first symbol it finds. faddr2line is recommended over gdb because
it handles duplicates and it also does function size checking.)
Here's an example of what a stack dump looks like after this change:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: sysrq_handle_crash+0x45/0x80
PGD 36bfa067 [ 29.650644] PUD 7aca3067
Oops: 0002 [#1] PREEMPT SMP
Modules linked in: ...
CPU: 1 PID: 786 Comm: bash Tainted: G E 4.9.0-rc1+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.1-1.fc24 04/01/2014
task: ffff880078582a40 task.stack: ffffc90000ba8000
RIP: 0010:sysrq_handle_crash+0x45/0x80
RSP: 0018:ffffc90000babdc8 EFLAGS: 00010296
RAX: ffff880078582a40 RBX: 0000000000000063 RCX: 0000000000000001
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000292
RBP: ffffc90000babdc8 R08: 0000000b31866061 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000007 R14: ffffffff81ee8680 R15: 0000000000000000
FS: 00007ffb43869700(0000) GS:ffff88007d400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000007a3e9000 CR4: 00000000001406e0
Stack:
ffffc90000babe00 ffffffff81572d08 ffffffff81572bd5 0000000000000002
0000000000000000 ffff880079606600 00007ffb4386e000 ffffc90000babe20
ffffffff81573201 ffff880036a3fd00 fffffffffffffffb ffffc90000babe40
Call Trace:
__handle_sysrq+0x138/0x220
? __handle_sysrq+0x5/0x220
write_sysrq_trigger+0x51/0x60
proc_reg_write+0x42/0x70
__vfs_write+0x37/0x140
? preempt_count_sub+0xa1/0x100
? __sb_start_write+0xf5/0x210
? vfs_write+0x183/0x1a0
vfs_write+0xb8/0x1a0
SyS_write+0x58/0xc0
entry_SYSCALL_64_fastpath+0x1f/0xc2
RIP: 0033:0x7ffb42f55940
RSP: 002b:00007ffd33bb6b18 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000046 RCX: 00007ffb42f55940
RDX: 0000000000000002 RSI: 00007ffb4386e000 RDI: 0000000000000001
RBP: 0000000000000011 R08: 00007ffb4321ea40 R09: 00007ffb43869700
R10: 00007ffb43869700 R11: 0000000000000246 R12: 0000000000778a10
R13: 00007ffd33bb5c00 R14: 0000000000000007 R15: 0000000000000010
Code: 34 e8 d0 34 bc ff 48 c7 c2 3b 2b 57 81 be 01 00 00 00 48 c7 c7 e0 dd e5 81 e8 a8 55 ba ff c7 05 0e 3f de 00 01 00 00 00 0f ae f8 <c6> 04 25 00 00 00 00 01 5d c3 e8 4c 49 bc ff 84 c0 75 c3 48 c7
RIP: sysrq_handle_crash+0x45/0x80 RSP: ffffc90000babdc8
CR2: 0000000000000000
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/69329cb29b8f324bb5fcea14d61d224807fb6488.1477405374.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some time ago, we brought our UV BIOS callback code up to speed with the
new EFI memory mapping scheme, in commit:
d1be84a232 ("x86/uv: Update uv_bios_call() to use efi_call_virt_pointer()")
By leveraging some changes that I made to a few of the EFI runtime
callback mechanisms, in commit:
80e7559607 ("efi: Convert efi_call_virt() to efi_call_virt_pointer()")
This got everything running smoothly on UV, with the new EFI mapping
code. However, this left one, small loose end, in that EFI_OLD_MEMMAP
(a.k.a. efi=old_map) will no longer work on UV, on kernels that include
the aforementioned changes.
At the time this was not a major issue (in fact, it still really isn't),
but there's no reason that EFI_OLD_MEMMAP *shouldn't* work on our
systems. This commit adds a check into uv_bios_call(), to see if we have
the EFI_OLD_MEMMAP bit set in efi.flags. If it is set, we fall back to
using our old callback method, which uses efi_call() directly on the __va()
of our function pointer.
Signed-off-by: Alex Thorlton <athorlton@sgi.com>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: <stable@vger.kernel.org> # v4.7 and later
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <rja@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1476928131-170101-1-git-send-email-athorlton@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 platform changes from Ingo Molnar:
"The main changes in this cycle were:
- SGI UV updates (Andrew Banman)
- Intel MID updates (Andy Shevchenko)
- Initial Mellanox systems platform (Vadim Pasternak)"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/mellanox: Fix return value check in mlxplat_init()
x86/platform/mellanox: Introduce support for Mellanox systems platform
x86/platform/uv/BAU: Add UV4-specific functions
x86/platform/uv/BAU: Fix payload queue setup on UV4 hardware
x86/platform/uv/BAU: Disable software timeout on UV4 hardware
x86/platform/uv/BAU: Populate ->uvhub_version with UV4 version information
x86/platform/uv/BAU: Use generic function pointers
x86/platform/uv/BAU: Add generic function pointers
x86/platform/uv/BAU: Convert uv_physnodeaddr() use to uv_gpa_to_offset()
x86/platform/uv/BAU: Clean up pq_init()
x86/platform/uv/BAU: Clean up and update printks
x86/platform/uv/BAU: Clean up vertical alignment
x86/platform/intel-mid: Keep SRAM powered on at boot
x86/platform/intel-mid: Add Intel Penwell to ID table
x86/cpu: Rename Merrifield2 to Moorefield
x86/platform/intel-mid: Implement power off sequence
x86/platform/intel-mid: Enable SD card detection on Merrifield
x86/platform/intel-mid: Enable WiFi on Intel Edison
x86/platform/intel-mid: Run PWRMU command immediately
Pull x86 cleanups from Ingo Molnar:
"Header file and a wrapper functions cleanup"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Migrate exception table users off module.h and onto extable.h
x86: Clean up various simple wrapper functions
Pull x86 boot updates from Ingo Molnar:
"The changes in this cycle were:
- Save e820 table RAM footprint on larger kernel configurations.
(Denys Vlasenko)
- pmem related fixes (Dan Williams)
- theoretical e820 boundary condition fix (Wei Yang)"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix kdump, cleanup aborted E820_PRAM max_pfn manipulation
x86/e820: Use much less memory for e820/e820_saved, save up to 120k
x86/e820: Prepare e280 code for switch to dynamic storage
x86/e820: Mark some static functions __init
x86/e820: Fix very large 'size' handling boundary condition
In case of error, the function platform_device_register_simple()
returns ERR_PTR() and never returns NULL. The NULL test in the
return value check must therefor be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add the UV4-specific function definitions and define an operations struct
to implement them in the BAU driver.
Many BAU MMRs, although functionally the same, have new addresses on UV4
due to hardware changes. Each MMR requires new read/write functions, but
their implementation in the driver does not change. Thus, it is enough to
enumerate them in the operations struct for the changes to take effect.
Signed-off-by: Andrew Banman <abanman@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <travis@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: akpm@linux-foundation.org
Cc: rja@sgi.com
Link: http://lkml.kernel.org/r/1474474161-265604-11-git-send-email-abanman@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The BAU on UV4 does not need to maintain the payload queue tail pointer. Do
not initialize the tail pointer MMR on UV4.
Note that write_payload_tail is not an abstracted BAU function since it is
an operation specific to pre-UV4 versions. Then we must switch on the UV
version to control its usage, for which we use uvhub_version rather than
is_uv*_hub because it is quicker/more concise.
Signed-off-by: Andrew Banman <abanman@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <travis@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: akpm@linux-foundation.org
Cc: rja@sgi.com
Link: http://lkml.kernel.org/r/1474474161-265604-10-git-send-email-abanman@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Software timeouts are not currently supported on BAU for UV4. Instead, the
BAU will rely on hardware-level fairness protocols to determine broadcast
timeouts.
Do not call enable_timeouts or calculate_destination_timeout on UV4. These
functions write to pre-UV4 MMRs so they generate error messages on UV4.
Signed-off-by: Andrew Banman <abanman@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <travis@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: akpm@linux-foundation.org
Cc: rja@sgi.com
Link: http://lkml.kernel.org/r/1474474161-265604-9-git-send-email-abanman@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Convert the use of UV version-specific functions to their abstracted
counterparts.
Signed-off-by: Andrew Banman <abanman@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <travis@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: akpm@linux-foundation.org
Cc: rja@sgi.com
Link: http://lkml.kernel.org/r/1474474161-265604-7-git-send-email-abanman@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Many BAU functions have different implementations depending on the UV
version. Rather than switching on the uvhub_version throughout the driver,
we can define a set of operations for each version. This is especially
beneficial for UV4, which will require many new MMR read/write functions.
Currently, the set of abstracted functions are the same for UV1, UV2, and
UV3. The functions were chosen because each one will have a different
implementation for UV4. Other functions will be added as needed to handle
new implementations or to cleanup the existing differences between UV1,
UV2, and UV3, i.e. read_status and wait_completion.
Signed-off-by: Andrew Banman <abanman@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <travis@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: akpm@linux-foundation.org
Cc: rja@sgi.com
Link: http://lkml.kernel.org/r/1474474161-265604-6-git-send-email-abanman@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The BAU driver should use the functions provided by uv_hub.h rather than
its own implementations. uv_physnodeaddr converts vaddrs to paddrs for
BAU MMR fields, but this is done better by uv_gpa_to_offset.
Signed-off-by: Andrew Banman <abanman@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <travis@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: akpm@linux-foundation.org
Cc: rja@sgi.com
Link: http://lkml.kernel.org/r/1474474161-265604-5-git-send-email-abanman@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The payload queue first MMR requires the physical memory address and hub
GNODE of where the payload queue resides in memory, but the associated
variables are named as if the PNODE were used. Rename gnode-related
variables and clarify the definitions of the payload queue head, last, and
tail pointers.
Signed-off-by: Andrew Banman <abanman@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <travis@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: akpm@linux-foundation.org
Cc: rja@sgi.com
Link: http://lkml.kernel.org/r/1474474161-265604-4-git-send-email-abanman@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch turns e820 and e820_saved into pointers to e820 tables,
of the same size as before.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20160917213927.1787-2-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
new EFI memory map reservation code didn't align reservations to
EFI_PAGE_SIZE boundaries causing bogus regions to be inserted into
the global EFI memory map - Matt Fleming
-----BEGIN PGP SIGNATURE-----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=S9gJ
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into efi/core
Pull EFI fix from Matt Fleming:
* Fix a boot crash reported by Mike Galbraith and Mike Krinkin. The
new EFI memory map reservation code didn't align reservations to
EFI_PAGE_SIZE boundaries causing bogus regions to be inserted into
the global EFI memory map (Matt Fleming)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mike Galbraith reported that his machine started rebooting during boot
after,
commit 8e80632fb2 ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
The ESRT table on his machine is 56 bytes and at no point in the
efi_arch_mem_reserve() call path is that size rounded up to
EFI_PAGE_SIZE, nor is the start address on an EFI_PAGE_SIZE boundary.
Since the EFI memory map only deals with whole pages, inserting an EFI
memory region with 56 bytes results in a new entry covering zero
pages, and completely screws up the calculations for the old regions
that were trimmed.
Round all sizes upwards, and start addresses downwards, to the nearest
EFI_PAGE_SIZE boundary.
Additionally, efi_memmap_insert() expects the mem::range::end value to
be one less than the end address for the region.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Tested-by: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Waiman reported that booting with CONFIG_EFI_MIXED enabled on his
multi-terabyte HP machine results in boot crashes, because the EFI
region mapping functions loop forever while trying to map those
regions describing RAM.
While this patch doesn't fix the underlying hang, there's really no
reason to map EFI_CONVENTIONAL_MEMORY regions into the EFI page tables
when mixed-mode is not in use at runtime.
Reported-by: Waiman Long <waiman.long@hpe.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
CC: Theodore Ts'o <tytso@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Scott J Norton <scott.norton@hpe.com>
Cc: Douglas Hatch <doug.hatch@hpe.com>
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Jiri Kosina