We call intel_dp_compute_rate() in intel_dp_compute_config() only to be
able to debug log the link_bw and rate_select parameters; we don't use
the parameters here for anything else. We call intel_dp_compute_rate()
again during link training where we actually need and use the
parameters.
Move the debug logging of link_bw and rate_select to
intel_dp_link_training_clock_recovery(), and clean up the extra
intel_dp_compute_rate() call and extra clutter from the already
overcrowded intel_dp_compute_config().
v2: Rewrote commit message (Rodrigo, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c5cf6a179e2d244eceb6bb80a792765d9efbee4f.1524730974.git.jani.nikula@intel.com
LSPCON likes to throw short HPDs during the enable seqeunce prior to the
link being trained. These obviously result in the channel CR/EQ check
failing and thus we schedule a pointless hotplug work to retrain the
link. Avoid that by ignoring the bad CR/EQ status until we've actually
initially trained the link.
I've not actually investigated to see what LSPCON is trying to signal
with the short pulse. But as long as it signals anything I think we're
supposed to check the link status anyway, so I don't really see other
good ways to solve this. I've not seen these short pulses being
generated by normal DP sinks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-5-ville.syrjala@linux.intel.com
intel_dp->channel_eq_status is used in exactly one function, and we
don't need it to persist between calls. So just go back to using a
local variable instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-4-ville.syrjala@linux.intel.com
In case of eDP because the panel has a fixed mode, the link rate
and lane count at which it is trained corresponds to the link BW
required to support the native resolution of the panel. In case of
panles with lower resolutions where fewer lanes are hooked up internally,
that number is reflected in the MAX_LANE_COUNT DPCD register of the panel.
So it is pointless to fallback to lower link rate/lane count in case
of link training failure on eDP connector since the lower link BW
will not support the native resolution of the panel and we cannot
prune the preferred mode on the eDP connector.
In case of Link training failure on the eDP panel, something is wrong
in the HW internally and hence driver errors out with a loud
and clear DRM_ERROR message.
v2:
* Fix the DEBUG_ERROR and add {} in else (Ville Syrjala)
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=103369
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507835618-23051-1-git-send-email-manasi.d.navare@intel.com
This adds the connector name when printing a debug message about the DP
link training result. It is useful to figure out what connector is
failing when multiple DP connectors are used.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170718142536.2306-1-paul.kocialkowski@linux.intel.com
If link training at a link rate optimal for a particular
mode fails during modeset's atomic commit phase, then we
let the modeset complete and then retry. We save the link rate
value at which link training failed, update the link status property
to "BAD" and use a lower link rate to prune the modes. It will redo
the modeset on the current mode at lower link rate or if the current
mode gets pruned due to lower link constraints then, it will send a
hotplug uevent for userspace to handle it.
This is also required to pass DP CTS tests 4.3.1.3, 4.3.1.4,
4.3.1.6.
This patch is a resend of the original commit id (233ce881dd
"drm/i915: Implement Link Rate fallback on Link training failure")
which got reverted in this commit id (afc1ebf456 Revert
"drm/i915: Implement Link Rate fallback on Link training failure")
due to CI failures.
After investigating the CI failures it was found that these
were essentially the failures which were always there but hidden because
they used to be DRM_DEBUG_KMS messages for link failures so never got
caught by CI. But now this patch actually throws DRM_ERROR if the link
training fails at RBR and 1 lane. So it caught these link train failures.
There were two failures:
1. On SKL 6700k this was because the machine in CI lab is a SKL desktop
without eDP on Port A. But our VBT initialization code in the driver writes
VBT defaults in a way that it always sets DP flag on Port A and this does
not get cleared after parsing the VBT outputs. This has been fixed in
commit id (bb1d132935 "drm/i915/vbt: split out defaults that are set
when there is no VBT) and (665788572c "drm/i915/vbt: don't propagate
errors from intel_bios_init())
2. On ILK-650 desktop - This was happening because of a bad monitor desktop
combination. I switched the monitor in the CI lab and that helped get rid
of the link failures on ILK system.
v10:
* Rebase on drm-tip and resend after revert
v9:
* Use the trimmed max values of link rate/lane count based on
link train fallback (Daniel Vetter)
v8:
* Set link_status to BAD first and then call mode_valid (Jani Nikula)
v7:
Remove the redundant variable in previous patch itself
v6:
* Obtain link rate index from fallback_link_rate using
the helper intel_dp_link_rate_index (Jani Nikula)
* Include fallback within intel_dp_start_link_train (Jani Nikula)
v5:
* Move set link status to drm core (Daniel Vetter, Jani Nikula)
v4:
* Add fallback support for non DDI platforms too
* Set connector->link status inside set_link_status function
(Jani Nikula)
v3:
* Set link status property to BAd unconditionally (Jani Nikula)
* Dont use two separate variables link_train_failed and link_status
to indicate same thing (Jani Nikula)
v2:
* Squashed a few patches (Jani Nikula)
Acked-by: Tony Cheng <tony.cheng@amd.com>
Acked-by: Harry Wentland <Harry.wentland@amd.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/16ca48b1e74c618929245e9a085b9e3483c3a16d.1491485983.git.jani.nikula@intel.com
There is some conflation related to sink rates, making this change more
complicated than it would otherwise have to be. There are three changes
here that are rather difficult to split up:
1) Use the intel_dp->sink_rates array for all DP, not just eDP 1.4. We
initialize it from DPCD on eDP 1.4 like before, but generate it based
on DP_MAX_LINK_RATE on others. This reduces code complexity when we
need to use the sink rates; they are all always in the sink_rates
array.
2) Update the sink rate array whenever we read DPCD, and use the
information from there. This increases code readability when we need
the sink rates.
3) Disentangle fallback rate limiting from sink rates. In the code, the
max rate is a dynamic property of the *link*, not of the *sink*. Do
the limiting after intersecting the source and sink rates, which are
static properties of the devices.
This paves the way for follow-up refactoring that I've refrained from
doing here to keep this change as simple as it possibly can.
v2: introduce use_rate_select and handle non-confirming eDP (Ville)
v3: don't clobber cached eDP rates on short pulse (Ville)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/071bad76467f8ab2e73f3f61ad52d5a468004c71.1490712890.git.jani.nikula@intel.com
Fix the number of tries in channel euqalization link training sequence
according to DP 1.2 Spec. It returns a boolean depending on channel
equalization pass or failure.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This function cleans up clock recovery loop in link training compliant
tp Dp Spec 1.2. It tries the clock recovery 5 times for the same voltage
or until max voltage swing is reached and removes the additional non
compliant retries. This function now returns a boolean values based on
if clock recovery passed or failed.
v3:
* Better Debug prints in case of failures (Mika Kahola)
v2:
* Rebased on top of new revision of vswing patch (Manasi Navare)
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Wrap the max. vswing check in a separate function.
This makes the clock recovery phase of DP link training cleaner
v3:
Fixed the paranthesis warning (Mika Kahola)
v2:
Fixed the Compiler warning (Mika Kahola)
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A full dump of link status can be handy in debugging link training
failures. Let's add that to the debug messages when link training fails.
v2: Removing unrelated clean up (Jani)
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470343716-5574-3-git-send-email-dhinakaran.pandiyan@intel.com
It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.
This is a manual revert of commits 5fa836a9d8 ("drm/i915: DP link
training optimization") and 4e96c97742 ("drm/i915: eDP link training
optimization").
Fixes: 5fa836a9d8 ("drm/i915: DP link training optimization")
Fixes: 4e96c97742 ("drm/i915: eDP link training optimization")
Cc: <stable@vger.kernel.org> # v4.2+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com
Per spec, TPS3 support is mandatory for downstream devices that support
HBR2. We've therefore logged errors on HBR2 without TPS3 since
commit 1da7d7131c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Sep 3 11:16:08 2015 +0300
drm/i915: ignore link rate in TPS3 selection
However, it seems there are real world devices out there that just
aren't spec compliant, and still work at HBR2 using TPS2. So reduce the
error message to debug logging.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92932
Fixes: 1da7d7131c ("drm/i915: ignore link rate in TPS3 selection")
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454667370-8001-2-git-send-email-jani.nikula@intel.com
In order to prepare for a link training with DDI, the state machine
would call intel_ddi_prepare_link_retrain(). To remove the dependency to
the hardware information, replace that direct call with a callback.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-7-git-send-email-ander.conselvan.de.oliveira@intel.com
Jani Nikula