The function zynqmp_pll_round_rate is used to find a most appropriate
PLL frequency which the hardware can generate according to the desired
frequency. For example, if the desired frequency is 297MHz, considering
the limited range from PS_PLL_VCO_MIN (1.5GHz) to PS_PLL_VCO_MAX (3.0GHz)
of PLL, zynqmp_pll_round_rate should return 1.872GHz (297MHz * 5).
There are two problems with the current code of zynqmp_pll_round_rate:
1) When the rate is below PS_PLL_VCO_MIN, it can't find a correct rate
when the parameter "rate" is an integer multiple of *prate, in other words,
if "f" is zero, zynqmp_pll_round_rate won't return a valid frequency which
is from PS_PLL_VCO_MIN to PS_PLL_VCO_MAX. For example, *prate is 33MHz
and the rate is 660MHz, zynqmp_pll_round_rate will not boost up rate and
just return 660MHz, and this will cause clk_calc_new_rates failure since
zynqmp_pll_round_rate returns an invalid rate out of its boundaries.
2) Even if the rate is higher than PS_PLL_VCO_MIN, there is still a risk
that zynqmp_pll_round_rate returns an invalid rate because the function
DIV_ROUND_CLOSEST makes some loss in the fractional part. If the parent
clock *prate is 33333333Hz and we want to set the PLL rate to 1.5GHz,
this function will return 1499999985Hz by using the formula below:
value = *prate * DIV_ROUND_CLOSEST(rate, *prate)).
This value is also invalid since it's slightly smaller than PS_PLL_VCO_MIN.
because DIV_ROUND_CLOSEST makes some loss in the fractional part.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20220826142030.213805-1-quanyang.wang@windriver.com
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The warning that a clock operation failed is only printed once. However,
the function is called for various different clocks. The limit hides the
warnings if different clocks are affected by the failures.
The clock ops might fail if the firmware that handles the clocks is
misconfigured. Therefore, replace the pr_warn_once with pr_debug to
allow the user to see all errors if necessary. By default, hide the
error messages and let drivers handle the errors.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20220119115434.2042017-1-m.tretter@pengutronix.de
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently firmware passes CCF specific flags to ZynqMP clock driver.
So firmware needs to be updated if CCF flags are changed. The firmware
should have its own 'flag number space' that is distinct from the
common clk framework's 'flag number space'. So define and use ZynqMP
specific common clock flags instead of using CCF flags.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lore.kernel.org/r/20210628070122.26217-2-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
'clk_hw_set_rate_range()' does not return any error code and 'ret' is
known to be 0 at this point, so this message can never be displayed.
Remove it.
Fixes: 3fde0e16d0 ("drivers: clk: Add ZynqMP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/71a9fed5f762a71248b8ac73c0a15af82f3ce1e2.1619867987.git.christophe.jaillet@wanadoo.fr
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When the firmware code is disabled, the incomplete error handling
in the clk driver causes compile-time warnings:
drivers/clk/zynqmp/pll.c: In function 'zynqmp_pll_recalc_rate':
drivers/clk/zynqmp/pll.c:147:29: error: 'fbdiv' is used uninitialized [-Werror=uninitialized]
147 | rate = parent_rate * fbdiv;
| ~~~~~~~~~~~~^~~~~~~
In function 'zynqmp_pll_get_mode',
inlined from 'zynqmp_pll_recalc_rate' at drivers/clk/zynqmp/pll.c:148:6:
drivers/clk/zynqmp/pll.c:61:27: error: 'ret_payload' is used uninitialized [-Werror=uninitialized]
61 | return ret_payload[1];
| ~~~~~~~~~~~^~~
drivers/clk/zynqmp/pll.c: In function 'zynqmp_pll_recalc_rate':
drivers/clk/zynqmp/pll.c:53:13: note: 'ret_payload' declared here
53 | u32 ret_payload[PAYLOAD_ARG_CNT];
| ^~~~~~~~~~~
drivers/clk/zynqmp/clk-mux-zynqmp.c: In function 'zynqmp_clk_mux_get_parent':
drivers/clk/zynqmp/clk-mux-zynqmp.c:57:16: error: 'val' is used uninitialized [-Werror=uninitialized]
57 | return val;
| ^~~
As it was apparently intentional to support this for compile testing
purposes, change the code to have just enough error handling for the
compiler to not notice the remaining bugs.
Fixes: 21f2375346 ("clk: zynqmp: Drop dependency on ARCH_ZYNQMP")
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f1c4e8c903fe2d5df5413421920a56890a46387a.1624356908.git.michal.simek@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If there is a IOCTL_SET_PLL_FRAC_MODE request sent to ATF ever,
we shouldn't skip invoking PM_CLOCK_ENABLE fn even though this
pll has been enabled. In ATF implementation, it will only assign
the mode to the variable (struct pm_pll *)pll->mode when handling
IOCTL_SET_PLL_FRAC_MODE call. Invoking PM_CLOCK_ENABLE can force
ATF send request to PWU to set the pll mode to PLL's register.
There is a scenario that happens in enabling VPLL_INT(clk_id:96):
1) VPLL_INT has been enabled during booting.
2) A driver calls clk_set_rate and according to the rate, the VPLL_INT
should be set to FRAC mode. Then zynqmp_pll_set_mode is called
to pass IOCTL_SET_PLL_FRAC_MODE to ATF. Note that at this point
ATF just stores the mode to a variable.
3) This driver calls clk_prepare_enable and zynqmp_pll_enable is
called to try to enable VPLL_INT pll. Because of 1), the function
zynqmp_pll_enable just returns without doing anything after checking
that this pll has been enabled.
In the scenario above, the pll mode of VPLL_INT will never be set
successfully. So adding set_pll_mode to check condition to fix it.
Fixes: 3fde0e16d0 ("drivers: clk: Add ZynqMP clock driver")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210406153131.601701-1-quanyang.wang@windriver.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The round_rate callback should only perform rate calculation and not
involve calling zynqmp_pll_set_mode to change the pll mode. So let's
move zynqmp_pll_set_mode out of round_rate and to set_rate callback.
Fixes: 3fde0e16d0 ("drivers: clk: Add ZynqMP clock driver")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210406154015.602779-1-quanyang.wang@windriver.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use direct function call instead of using eemi ops for
clock_getdivider.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Link: https://lore.kernel.org/r/1587761887-4279-9-git-send-email-jolly.shah@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use direct function call instead of using eemi ops for
clock_setdivider.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Link: https://lore.kernel.org/r/1587761887-4279-8-git-send-email-jolly.shah@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warn user if clock is used by more than allowed devices.
This check is done by firmware and returns respective
error code. Upon receiving error code for excessive user,
warn user for the same.
This change is done to restrict VPLL use count. It is
assumed that VPLL is used by one user only.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-4-git-send-email-rajan.vaja@xilinx.com
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds CCF compliant clock driver for ZynqMP.
Clock driver queries supported clock information from
firmware and regiters pll and output clocks with CCF.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Tejas Patel <tejasp@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Quanyang Wang