Remove some legacy code from the davinci_nand driver, which made
cmdlinepart ignore the the MTD ID passed to it. Boards can have
multiple NAND chips, and some do (like the DM357 EVM), so this
dated hack is undesirable.
Correct labels are like "davinci_nand.0" (for chipselect 0).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In addition to adding the Numonyx manufacturer code, this patch
also ensures 'sync. write' is disabled when reading identification
data - something that the Numonyx chip objects to, but the
Samsung chip seems to ignore.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
this patch add m45pe10 [1] chip support to the m25p80 driver.
[1] http://www.numonyx.com/Documents/Datasheets/M45PE10.pdf
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make sure to pass the same dev_id data to free_irq() that was
used when calling request_irq(), otherwise we get a warning about
freeing an already free IRQ.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Type of 'byte_addr' needes to be 'unsigned int' for 512 byte
ECC support.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Minimal support for the 4-bit ECC engine found on DM355, DM365,
DA830/OMAP-L137, and similar recent DaVinci-family chips.
This is limited to small-page flash for now; there are some page
layout issues for large page chips. Note that most boards using
this engine (like the DM355 EVM) include 2GiB large page chips.
Sanity tested on DM355 EVM after swapping the socketed NAND for
a small-page one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make the DaVinci NAND driver require platform_data with
board-specific configuration. We can't actually do any
kind of sane job of configuring it otherwise.
Also fix the comment about picking the "best" ECC mode.
We can't do those any more; that relied on knowing what kind
of CPU we're using (they don't all support 4-bit ECC), and
current policy is that drivers not have cpu_is_*() checks.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Resolve issue noted by Sneha: when computing oobavail from
the list of free areas in the OOB, don't assume there will
always be an unused slot at the end. With ECC_HW_SYNDROME
and 4KiB page chips, it's fairly likely there *won't* be one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Narnakaje, Snehaprabha" <nsnehaprabha@ti.com>"
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With CONFIG_HOTPLUG=n, the following eror occurred during link:
local symbol 0: discarded in section `.devexit.text' from
drivers/built-in.o
It was caused by improper section reference. The __devexit_p()
should be added to the .remove function.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[Artem: re-worked the patch: made it release resources when the
module is unloaded, made it do module referencing, made it really
independent on UBI, tested it with the UBI test-suite which can
be found in ubi-2.6.git/tests/ubi-tests, re-named most of the
funcs/variables to get rid of the "ubi" word and make names
consistent.]
Signed-off-by: Dmitry Pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Remove built-in gluebi support. This is a preparation for a
standalone glubi module support
Signed-off-by: Dmitry Pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI volume notifications are intended to create the API to get clients
notified about volume creation/deletion, renaming and re-sizing. A
client can subscribe to these notifications using 'ubi_volume_register()'
and cancel the subscription using 'ubi_volume_unregister()'. When UBI
volumes change, a blocking notifier is called. Clients also can request
"added" events on all volumes that existed before client subscribed
to the notifications.
If we use notifications instead of calling functions like 'ubi_gluebi_xxx()',
we can make the MTD emulation layer to be more flexible: build it as a
separate module and load/unload it on demand.
[Artem: many cleanups, rework locking, add "updated" event, provide
device/volume info in notifiers]
Signed-off-by: Dmitry Pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch improves UBI errors handling. ATM UBI switches to
R/O mode when the WL worker fails to read the source PEB.
This means that the upper layers (e.g., UBIFS) has no
chances to unmap the erroneous PEB and fix the error.
This patch changes this behaviour and makes UBI put PEBs
like this into a separate RB-tree, thus preventing the
WL worker from hitting the same read errors again and
again.
But there is a 10% limit on a maximum amount of PEBs like this.
If there are too much of them, UBI switches to R/O mode.
Additionally, this patch teaches UBI not to panic and
switch to R/O mode if after a PEB has been copied, the
target LEB cannot be read back. Instead, now UBI cancels
the operation and schedules the target PEB for torturing.
The error paths has been tested by ingecting errors
into 'ubi_eba_copy_leb()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes the error path in the WL worker - in same cases
UBI oopses when 'goto out_error' happens and e1 or e2 are NULL.
This patch also cleans up the error paths a little. And I have
tested nearly all error paths in the WL worker.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch is a clean-up and a preparation for the following
patches. It introduece constants for the return values of the
'ubi_eba_copy_leb()' function.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch allows commandline partition processing to
work with the s3c2410 NAND platform driver.
Signed-off-by: Andy Green <andy@warcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: Change andy@openmoko.com to andy@warmcat.com]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix NAND CFG debug order.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: Change andy@openmoko.com to andy@warmcat.com, subject cleanup]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
~ Avoid warning without generating code.
(I don't even get the warning without the macro uninitialized_var).
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: subject cleanup]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This makes us take note about the chosen ECC mode per-chip and
not the one set globally.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: andy@openmoko.com => andy@warmcat.com, rewrite subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 57fee4a58f added an
method to specify the platform device compatibility by using
an id-table instead of registering multiple drivers.
Move the S3C24XX NAND driver to using this ID table.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CC: Eric Miao <eric.miao@marvell.com>
Remove all references to MTD ioctls from fs/compat_ioctl.c and let
them all be handled by mtd_compat_ioctl().
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
1) Move the MEMREADOOB/MEMWRITEOOB compat_ioctl wrappers from
fs/compat_ioctl.c into mtdchar.c . Original request was here:
http://lkml.org/lkml/2009/4/1/295
2) Add missing COMPATIBLE_IOCTL lines, so that mtd-utils does not error
out when running in 64/32 compatibility mode.
LKML-Reference: <200904011650.22928.arnd@arndb.de>
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New MEMERASE/MEMREADOOB/MEMWRITEOOB ioctls are needed in order to support
64-bit offsets into large NAND flash devices.
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As pointed out by Kay Sievers, the name size limit is gone
from the driver-core, and BUS_ID_SIZE is obsolescent.
Rather than just papering over the problem by replacing the mtdname
array size with an arbitrary '20 + 2', fix the problem properly and
handle arbitrary name sizes.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds MTD concatenation support to integrator-flash.c for
platforms with more than one block of flash memory (e.g. RealView
PB11MPCore). The implementation is based on the sa1100-flash.c one.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The following patch fixes:
- re-initialization of host->col_addr which is used as byte index
between the successive READID flash commands.
- compile error when CONFIG_PM is enabled
- pass on the error code from clk_get()
- return -ENOMEM in case of failed ioremap()
- pass on the return value of platform_driver_probe() directly
- remove excessive printk
- let command line partition table parsing with mxc_nand name.
The cmd_line parsing is done via <mtd-id> name that differs
from mxc_nand by default and looks like "NAND 256MiB 1,8V 8-bit"
Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This breaks the dilnetpc map driver, but it could be fixed not to use
that option. We want to simplify the partition handling, and this is a
step towards that.
Remove superfluous 'index' field from private struct mtd_part too, while
we're at it.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now the MTD core will do this for us, we don't need to hook it up from
the board drivers.
Shame we can't do shutdown from the class too...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is intended to suspend/resume the _chip_, while we leave board
drivers to handle their own suspend/resume for the controller.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes a minor problem where we may fail to wake
upe the UBI background thread. This is not fatal at all,
it may just result at sligtly worse performace for a short
period of time, just because the thread will be woken up
when real I/O on the UBI starts.
Anywey, the issue is the race condition between
'ubi_attach_mtd_dev()' and 'ubi_thread()'. If we do not
serialize them, the 'wake_up_process()' call may be done
before 'ubi_thread()' went seep, but after it checked
'ubi->thread_enabled'.
This issue was spotted by Shin Hong <hongshin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The @vol->upd_marker should be protected by the @ubi->device_mutex,
otherwise 'paranoid_check_volume()' complains sometimes because
vol->upd_marker is 1 while vtbl_rec->upd_marker is 0.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
If a volume paranoid check fails, do not return an error
code to the caller, but just print error messages and go
forward. The primary reason for this is that it is difficult
to recover and cancel the operation at that stage.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I am experiencing an error in 'paranoid_check_volume()'. Add
dump_stack() there to make it easier to identify the reasons
of the error.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When paranoid checs are enabled, the 'io_paral' test from the
'mtd-utils' package fails. The symptoms are:
UBI error: paranoid_check_all_ff: flash region at PEB 3973:512, length 15872 does not contain all 0xFF bytes
UBI error: paranoid_check_all_ff: paranoid check failed for PEB 3973
UBI: hex dump of the 512-16384 region
It turned out to be a bug in the checking function. Suppose there
are 2 tasks - A and B. Task A is the wear-levelling working
('wear_leveling_worker()'). It is reading the VID header to find
which LEB this PEB belongs to. Say, task A is reading header
of PEB X. Suppose PEB X is unmapped, and has no VID header.
Task B is trying to write to PEB X.
Task A: in 'ubi_io_read_vid_hdr()': reads the VID header from PEB X.
The read data contain all 0xFF bytes.
Task B: writes VID header and some data to PEB X
Task A: assumes PEB X is empty, calls 'paranoid_check_all_ff()', which
fails.
The solution for this problem is to make 'paranoid_check_all_ff()'
re-read the VID header, re-check it, and only if it is not there,
check the rest. This now implemented by the 'paranoid_check_empty()'
function.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The @ubi->dbg_peb_buf is needed only when paranoid checks are
enabled, not when debugging in general is enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Various minor improvements to the debugging messages which
I found useful while hunting problems.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The mutex essencially protects the entire UBI device, so the
old @volumes_mutex name is a little misleading.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The @mult_mutex does not serve any purpose. We already have
@volumes_mutex and it is enough. The @volume mutex is pushed
down to the 'ubi_rename_volumes()', because we want first
to open all volumes in the exclusive mode, and then lock the
mutex, just like all other ioctl's (remove, re-size, etc) do.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
mtd_blkdevs processes requests one-by-one synchronously from a kthread
and can be easily converted to dequeueing model. Convert it.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With the previous changes, the followings are now guaranteed for all
requests in any valid state.
* blk_rq_sectors() == blk_rq_bytes() >> 9
* blk_rq_cur_sectors() == blk_rq_cur_bytes() >> 9
Clean up accessor usages. Notable changes are
* nbd,i2o_block: end_all used instead of explicit byte count
* scsi_lib: unnecessary conditional on request type removed
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.infradead.org/mtd-2.6:
mtd: fix timeout in M25P80 driver
mtd: Bug in m25p80.c during whole-chip erase
mtd: expose subpage size via sysfs
mtd: mtd in mtd_release is unused without CONFIG_MTD_CHAR
Extend erase timeout in M25P80 SPI Flash driver.
The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a logic error in "whole chip erase" for the m25p80 family. If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase. This patch corrects that.
Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc. Increasing it allows me to successfully program
the device on my board.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
end_request() has been kept around for backward compatibility;
however, it's about time for it to go away.
* There aren't too many users left.
* Its use of @updtodate is pretty confusing.
* In some cases, newer code ends up using mixture of end_request() and
[__]blk_end_request[_all](), which is way too confusing.
So, add [__]blk_end_request_cur() and replace end_request() with it.
Most conversions are straightforward. Noteworthy ones are...
* paride/pcd: next_request() updated to take 0/-errno instead of 1/0.
* paride/pf: pf_end_request() and next_request() updated to take
0/-errno instead of 1/0.
* xd: xd_readwrite() updated to return 0/-errno instead of 1/0.
* mtd/mtd_blkdevs: blktrans_discard_request() updated to return
0/-errno instead of 1/0. Unnecessary local variable res
initialization removed from mtd_blktrans_thread().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Joerg Dorchain <joerg@dorchain.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Laurent Vivier <Laurent@lvivier.info>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: unsik Kim <donari75@gmail.com>
MTD has got sysfs support in 2.6.30-rc1. But subpage size is not
exposed there - do this.
UBI utilities badly need this parameter. At the moment there is
no way to get subpage size - ioctls do not return it. And we
just got sysfs support, so we can easilly extend it with this
additional parameter.
This can be merged late in the development cycle because:
1. sysfs support has been just added - there are no users for
it so far, even.
2. UBI utilities really need this parameter, and it is better
not to delay this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/mtdcore.c: In function 'mtd_release':
drivers/mtd/mtdcore.c:51: warning: unused variable 'mtd'
[akpm: make it actually build]
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
Prevent NUMONYX M29W128G memories from using write buffer,
because it doesn't work properly.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In the existing implementation, ecc_stats fields are incremented only by
one, regardless of master mtd errors number. For example, if there are N
errors were corrected by ECC, partition ecc_stats.corrected will be
incremented by one.
This commit changes simple increment to sum of old value and parent mtd
error count.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern. The TQM8548_BE requires a further short delay
after writing out a buffer. Normally the R/B pin should be checked, but
it's not connected on the TQM8548_BE. The existing driver uses similar
fixed delay points. To manage these extra delays in a more general way,
I introduced the "fsl,ump-wait-flags" property allowing the board-
specific driver to specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. This requires support for multiple GPIOs for the RNB pins.
The NAND chips are selected through address lines defined by the
FDT property "fsl,upm-addr-line-cs-offsets".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: use strstarts()
strstarts: helper function for !strncmp(str, prefix, strlen(prefix))
arm: allow usage of string functions in linux/string.h
module: don't use stop_machine on module load
module: create a request_module_nowait()
module: include other structures in module version check
module: remove the SHF_ALLOC flag on the __versions section.
module: clarify the force-loading taint message.
module: Export symbols needed for Ksplice
Ksplice: Add functions for walking kallsyms symbols
module: remove module_text_address()
module: __module_address
module: Make find_symbol return a struct kernel_symbol
kernel/module.c: fix an unused goto label
param: fix charp parameters set via sysfs
Fix trivial conflicts in kernel/extable.c manually.
Move the driver model init code out of the "#ifdef CONFIG_PROC_FS"
block.
Tested with both values of CONFIG_PROC_FS . Tested with CONFIG_MTD=m .
Issue was reported here: http://lkml.org/lkml/2009/4/4/107
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Follow-on patch to the previous driver model patch for the MTD
framework. This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.
Based on a patch from Kay Sievers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
1) Add more sysfs attributes: flags, size, erasesize, writesize,
oobsize, numeraseregions, name
2) Move core_initcall() code into init_mtd(). The original approach
does not work if CONFIG_MTD=m .
3) Add device_unregister() in del_mtd_device() so that devices get
removed from sysfs as each driver is unloaded.
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Update driver model support in the MTD framework, so it fits
better into the current udev-based hotplug framework:
- Each mtd_info now has a device node. MTD drivers should set
the dev.parent field to point to the physical device, before
setting up partitions or otherwise declaring MTDs.
- Those device nodes always map to /sys/class/mtdX device nodes,
which no longer depend on MTD_CHARDEV.
- Those mtdX sysfs nodes have a "starter set" of attributes;
it's not yet sufficient to replace /proc/mtd.
- Enabling MTD_CHARDEV provides /sys/class/mtdXro/ nodes and the
/sys/class/mtd*/dev attributes (for udev, mdev, etc).
- Include a MODULE_ALIAS_CHARDEV_MAJOR macro. It'll work with
udev creating the /dev/mtd* nodes, not just a static rootfs.
So the sysfs structure is pretty much what you'd expect, except
that readonly chardev nodes are a bit quirky.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
A pointer to plat_nand_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Hamish Moffatt <hamish@cloud.net.au>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A pointer to sa1100_mtd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The commit:
platform driver: fix incorrect use of 'platform_bus_type' with 'struct device_driver'
contains this:
-static int __exit pxa2xx_flash_remove(struct device *dev)
+static int __exit pxa2xx_flash_remove(struct platform_device *dev)
...
- .remove = __exit_p(pxa2xx_flash_remove),
+ .remove = __devexit_p(pxa2xx_flash_remove),
which leads to the following build error:
`pxa2xx_flash_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
This is not the only instance of it in this patch - all __exit_p's
touched by this patch have been converted to __devexit_p's without
regard to the original function.
Let's revert this change and, if we are going to convert functions
to be __devexit/__devinit, lets have that as a _separate_ patch doing
just that change.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: Replace and remove risky (non-EXPORTed) API
module_text_address() returns a pointer to the module, which given locking
improvements in module.c, is useless except to test for NULL:
1) If the module can't go away, use __module_text_address.
2) Otherwise, just use is_module_text_address().
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix this sparse warnings:
drivers/mtd/tests/mtd_oobtest.c:139:33: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:192:33: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:219:41: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:284:25: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:525:25: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:545:25: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:569:33: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:589:33: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:613:33: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:633:33: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:673:41: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_oobtest.c:701:33: warning: Using plain integer as NULL pointer
drivers/mtd/tests/mtd_readtest.c:74:41: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need to have a "\n" on a MODULE_DESCRIPTION, remove it.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
Conflicts:
arch/sparc/kernel/time_64.c
drivers/gpu/drm/drm_proc.c
Manual merge to resolve build warning due to phys_addr_t type change
on x86:
drivers/gpu/drm/drm_info.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
simple_set_mnt() is defined as returning 'int' but always returns 0.
Callers assume simple_set_mnt() never fails and don't properly cleanup if
it were to _ever_ fail. For instance, get_sb_single() and get_sb_nodev()
should:
up_write(sb->s_unmount);
deactivate_super(sb);
if simple_set_mnt() fails.
Since simple_set_mnt() never fails, would be cleaner if it did not
return anything.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (96 commits)
sh: add support for SMSC Polaris platform
sh: fix the HD64461 level-triggered interrupts handling
sh: sh-rtc wakeup support
sh: sh-rtc invalid time rework
sh: sh-rtc carry interrupt rework
sh: disallow kexec virtual entry
sh: kexec jump: fix for ftrace.
sh: kexec: Drop SR.BL bit toggling.
sh: add kexec jump support
sh: rework kexec segment code
sh: simplify kexec vbr code
sh: Flush only the needed range when unmapping a VMA.
sh: Update debugfs ASID dumping for 16-bit ASID support.
sh: tlb-pteaex: Kill off legacy PTEA updates.
sh: Support for extended ASIDs on PTEAEX-capable SH-X3 cores.
sh: sh7763rdp: Change IRQ number for sh_eth of sh7763rdp
sh: espt-giga board support
sh: dma: Make G2 DMA configurable.
sh: dma: Make PVR2 DMA configurable.
sh: Move IRQ multi definition of DMAC to defconfig
...
Now as all PXA Zaurii are converted to use the physmap map,
drop the sharpsl-flash map completely.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SLOF has a further node which could not be evaluated
by the current routine. The current routine returns
because the node hasn't the required reg property. As
fix this patch adds a check to determine the partition
child nodes. If the node is not a partition the number
of total partitions will be decreased and loop continues
with the next nodes.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for direct mapping through mtdconcat, if possible, by attaching the
samebacking_dev_info structure to the master.
It has some restrictions:
(1) It won't permit direct mapping of concatenated devices that have differing
BDIs.
(2) It doesn't support maps that span the 'gap' between devices, although it
possibly could if the devices spanned across return compatible
(ie. contiguous) addresses from their get_unmapped_area() ops.
Signed-off-by: Gavin Lambert <gavinl@compacsort.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Present backing device capabilities for MTD character device files to allow
NOMMU mmap to do direct mapping where possible.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
OneNAND write-while-program method of writing improves performance,
compared with ordinary writes, by transferring data to OneNAND's
RAM buffers atthe same time as programming the NAND core.
When writing several NAND pages at a time, an improvement of
12% to 25% is seen.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
panic_write may read in an interrupt context.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently redboot and afx parser return allocated mtd_partition array
and cmdlinepart and ar7 return persistent array.
This patch make cmdlinepart and ar7 also return allocated array, so
that all users can free it regardless of parser type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD's have both an index number and a name. Formerly,
the MTD selected for mtdoops was done only by index
number. With this patch, a name can be used instead.
For example, the kernel command line:
console=ttyMTD5
selects MTD 5 for mtdoops. But now this is also possible:
console=ttyMTD,log
which selects the MTD named "log" for mtdoops.
This has the advantage that partitions can be added or
removed that would affect the MTD index number but not the
name, without having to then change the kernel command line.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The nftl module is missing the block-major-93-* alias that would cause
it to be auto-loaded when a nftl of that type is opened. This patch
adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The mtdchar module is missing the char-major-90-* alias that would cause
it to be auto-loaded when a device of that type is opened. This patch
adds the alia..
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the inval_cache_and_wait_for_operation() is re-entered by write operation when erase
operation is in progress, the chip->erase_suspended will be cleared, this cause the erase
timeo is not reset and will result time out error for erase.
Signed-off-by: Graff Yang <graff.yang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a map driver for NOR flash chips on RBTX4939 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Bächle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the integrated NAND flash controller of the
TXx9 family.
Once upon a time there were tx4925ndfmc and tx4938ndfmc driver. They
were removed due to bitrot in 2005.
This new driver is completely rewritten based on a driver in CELF patch
archive.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Bächle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move mtd_has_partitions() and mtd_has_cmdlinepart() inlines from a
DaVinci-specific driver to the <linux/mtd/partitions.h> header.
Use those to eliminate #ifdefs in two drivers which had their own
definitions of mtd_has_partitions().
Quite a lot of other MTD drivers could benefit from using use one or both
of these to remove #ifdeffery. Maybe some Janitors would like to help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove <linux/miscdevice.h> from various drivers which don't actually use
any of its contents. There are still a number of these left in
arch-specific bits of the tree.
(Found by diffing results of "grep -rl" for linux/miscdevice.h and for
misc_register, examining the differences, and verifying removals with a
build test.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Usage of davinci-specific cpu_is macros is not allowed in drivers.
These options should be passed in through platform_data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix incorrect debug messages (*write* not read); someone committed some
cut'n'paste bugs. There might be more, I only noticed these since I was
looking for nand_read usage and landed in some very wrong functions.
IMO all MTD debugging message framework is goofed, anyway. It uses
"DEBUG" in a way that's incompatible with usage most everywhere else in
the kernel, and which prevents normal pr_dbg() and dev_dbg() calls from
working right.
[True. It predates those by a long way, and should probably be updated
to use them. dwmw2]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a device driver for the NAND flash controller found on the various
DaVinci family chips. It handles up to four SoC chipselects, and some
flavors of secondary chipselect (e.g. based on upper bits of the address
bus) as used with some multichip packages. (Including the 2 GiB chips
used on some TI devel boards.)
The 1-bit ECC hardware is supported (3 bytes ECC per 512 bytes data); but
not yet the newer 4-bit ECC (10 bytes ECC per 512 bytes data), as
available on chips like the DM355 or OMAP-L137 and needed with the more
error-prone MLC NAND chips.
This is a cleaned-up version of code that's been in use for several years
now; sanity checked with the new drivers/mtd/tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The syndrome based page read/write routines store ECC, and possibly other
"OOB" data, right after each chunk of ECC'd data. With ECC chunk size of
512 bytes and a large page (2KiB) NAND, the layout is:
data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover
Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines
use a traditional layout -- data OOB, disregarding the prepad and postpad
values -- so when they're used with that type of ECC hardware, those calls
mix up the data and OOB. Which means, in particular, that bad block
tables won't be found on startup, with data corruption and related chaos
ensuing.
The current syndrome-based drivers in mainline all seem to use one chunk
per page; presumably they haven't noticed such bugs.
Fix this, by adding read/write page_raw_syndrome() routines as siblings of
the existing non-raw routines; "raw" just means to bypass the ECC
computations, not change data and OOB layout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The bf5xx_nand_add_partition() func is only called by __devinit functions,
so put it into the __devinit section as well
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Only set DMAC1_PERIMUX once we have requested and been granted the dma
channel to prevent breaking other peripherals in the error case
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Convert the PS3 Video RAM Storage Driver from an MTD driver to a plain block
device driver.
The ps3vram driver exposes unused video RAM on the PS3 as a block device
suitable for storage or swap. Fast data transfer is achieved using a local
cache in system RAM and DMA transfers via the GPU.
The new driver is ca. 50% faster for reading, and ca. 10% for writing.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit e480814f13 ("[MTD] [MAPS] physmap:
fix wrong free and del_mtd_{partition,device}") introduces a NULL pointer
dereference in physmap_flash_remove when called from the error path in
physmap_flash_probe (if map_probe failed).
Call del_mtd_{partition,device} only if info->cmtd was not NULL.
Reported-by: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 771999b65f ("[MTD] DataFlash: bugfix,
binary page sizes now handled") broke support for probing AT45DB321C flash
chips. These chips do not support the "page size" status bit, so if we
match the JEDEC id return early.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the Sega Dreamcast visual memory unit as a
flash mapping. It requires changes in the maple bus driver (posted
separately) to support block reads and writes.
The VMU is a 'smart' flash device, with a built-in 8-bit controller -
for instance there is an erase before a write but it is hidden from the
user. But the device's overall behaviour means it works well with the
mtd layer and it is appropriate to add it as an mtd mapping.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The definitions of PXA_CS<x>_PHYS are really PXA2xx specific and should
be moved out of pxa-regs.h. As an illustration, the PXA3xx static chip
selects definitions are added into pxa3xx-regs.h.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We really don't want the BIOS flash mapping hacks to get automatically
loaded.
No idea why it isn't using pci_register_driver() though -- that should
be fine... and is even _present_ but disabled by #if 0.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now, we can call fsync() on an UBI volume.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct a build error. bfin-async uses complex mappings and so needs it.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
commit 176bf2e0f1 ("physmap: fix leak of
memory returned by parse_mtd_partitions") deals with a memory leak and
frees the pointer array of mtd_partition after the call to
add_mtd_partitions(). the problem is that mtd_table[x]->name still points
to the freed memory.
Aldo physmap_flash_remove() should call del_mtd_partitions() or
del_mtd_device() only once.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Reported-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Tested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
"flash" is a very generic name for a platform_driver that is only
available on SA11x0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
X86_PC is the only remaining 'sub' architecture, so we dont need
it anymore.
This also cleans up a few spurious references to X86_PC in the
driver space - those certainly should be X86.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
X86_GENERICARCH is a misnomer - it contains non-PC 32-bit architectures
that are not included in the default build.
Rename it to X86_32_NON_STANDARD.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Introduce a new ioctl UBI_IOCSETPROP to set properties
on a volume. Also add the first property:
UBI_PROP_DIRECT_WRITE, this property is used to set the
ability to use direct writes in userspace
Signed-off-by: Sidney Amani <seed@uffs.org>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
GregKH asked to fix UBI which has fake device release method. Indeed,
we have to free UBI device description object from the release method,
because otherwise we'll oops is someone opens a UBI device sysfs file,
then the device is removed, and he reads the file. With this fix, he
will get -ENODEV instead of an oops.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
A negative devlength won't get noticed and clean up:
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
UBI ioctl's do not work when running 64-bit kernel and 32-bit
user-land. Fix this by adding the compat_ioctl method.
Also, UBI serializes all ioctls, so more than one ioctl at a time
is not a problem. Amd UBI does not seem to depend on anything else,
so use unlocked_ioctl instead of ioctl (no BKL needed).
Reported-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Some ioctl's in UBI are enabled only when debugging is switched
on. There is not particular reason for this, just noone needed
them. However, some people need the now for their user-space
development. Thus, allow these ioctl's even if UBI debugging
is disabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl to check if an LEB is mapped or not (as a
debugging option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl for the LEB unmap operation (as a debugging
option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl for the LEB map operation (as a debugging
option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Which means if inftl or similar are loaded with it (which is a dumb thing
to do admittedly) it may oops.
Closes#8108
[dwmw2: change error to -EROFS to match write-protected flash]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (67 commits)
[MTD] [MAPS] Fix printk format warning in nettel.c
[MTD] [NAND] add cmdline parsing (mtdparts=) support to cafe_nand
[MTD] CFI: remove major/minor version check for command set 0x0002
[MTD] [NAND] ndfc driver
[MTD] [TESTS] Fix some size_t printk format warnings
[MTD] LPDDR Makefile and KConfig
[MTD] LPDDR extended physmap driver to support LPDDR flash
[MTD] LPDDR added new pfow_base parameter
[MTD] LPDDR Command set driver
[MTD] LPDDR PFOW definition
[MTD] LPDDR QINFO records definitions
[MTD] LPDDR qinfo probing.
[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately
[MTD] [NAND] pxa3xx: fix non-page-aligned reads
[MTD] [NAND] fix nandsim sched.h references
[MTD] [NAND] alauda: use USB API functions rather than constants
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] fix m25p80 64-bit divisions
[MTD] fix dataflash 64-bit divisions
[MTD] [NAND] Set the fsl elbc ECCM according the settings in bootloader.
...
Fixed up trivial debug conflicts in drivers/mtd/devices/{m25p80.c,mtd_dataflash.c}
[dwmw2: updated and made to still register whole device first]
Signed-off-by: Philip Rakity <pakity@yahoo.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NOR Flash memory K8P2815UQB from Samsung uses the major version
number '0'. Add a quirk to cope with it.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
serial: Add driver for the Cell Network Processor serial port NWP device
powerpc: enable dynamic ftrace
powerpc/cell: Fix the prototype of create_vma_map()
powerpc/mm: Make clear_fixmap() actually work
powerpc/kdump: Use ppc_save_regs() in crash_setup_regs()
powerpc: Export cacheable_memzero as its now used in a driver
powerpc: Fix missing semicolons in mmu_decl.h
powerpc/pasemi: local_irq_save uses an unsigned long
powerpc/cell: Fix some u64 vs. long types
powerpc/cell: Use correct types in beat files
powerpc: Use correct type in prom_init.c
powerpc: Remove unnecessary casts
mtd/ps3vram: Use _PAGE_NO_CACHE in memory ioremap
mtd/ps3vram: Use msleep in waits
mtd/ps3vram: Use proper kernel types
mtd/ps3vram: Cleanup ps3vram driver messages
mtd/ps3vram: Remove ps3vram debug routines
mtd/ps3vram: Add modalias support to the ps3vram driver
mtd/ps3vram: Add ps3vram driver for accessing video RAM as MTD
powerpc: Fix iseries drivers build failure without CONFIG_VIOPATH
...
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use _PAGE_NO_CACHE for gpu memory ioremap. Also,
add __iomem attribute to gpu memory pointer and
change use of memset() to memset_io().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace the use of udelay() with msleep() in the looping wait routines
ps3vram_notifier_wait() and ps3vram_wait_ring().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace the use of stdint.h types with kernel types
in the ps3vram driver.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cleanup the ps3vram driver messages. Add a new struct device pointer
variable dev to struct ps3vram_priv and use dev_dbg(), pr_dbg(), etc.
where appropriate.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the ps3vram debug routines ps3vram_dump_ring() and
ps3vram_dump_reports(). These routines are not needed.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update ps3vram driver to use the new ps3 three id modalias support.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ps3vram driver, which exposes unused video RAM on the PS3 as a MTD
device suitable for storage or swap. Fast data transfer is achieved
using a local cache in system RAM and DMA transfers via the GPU.
Signed-off-by: Vivien Chappelier <vivien.chappelier@free.fr>
Signed-off-by: Jim Paris <jim@jtan.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
The current ndfc driver only compiles under arch/ppc. This arch was
removed from the kernel. I notice the event entry for the ndfc in
Kconfig has been removed in 2.6.28.
This patch converts the ndfc to a proper OF (OpenFirmware) driver. I
can give a working example of the DTS if needed.
The patch has been in production use on the PIKA Warp Appliance and is
in use by others. The Warp basically boots from NAND, so the ndfc driver
is very important to us.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-By: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We have two components to manage LPDDR flash memories in Linux.
1. It is a driver for chip probing and reading its capabilities
2. It is a device operations driver.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Physmap is a generic map driver for different platforms and flash types.
We added support of LPDDR to physmap.
All changes here are related to introduction of new pfow_base parameter.
This parameter is valid in case of LPDDR chips only.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Driver which handles device command operation.
Details on device operations are available here:
http://www.numonyx.com/Documents/Datasheets/DS-315768_Velocity-Discrete.pdf
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
LPDDR flash chips are based on completely new kind of chips probing.
Device capabilities are available via special request.
We sent field request command which contains Major and Minor numbers - and
recieve corresponend value.
All requests are performed within PFOW window.
Detailed information about qinfo records can be found here:
http://www.numonyx.com/Documents/Datasheets/DS-315768_Velocity-Discrete.pdf
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The various fields in NDTR{01} are in units of clock ticks minus one, but the
ns2cycle macro mistakenly adds one, inflating the number of clock ticks and
making it impossible to set any of these fields to zero.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reads from non-page-aligned addresses were broken because while the
address to read from was correctly written to NDCB*, a full page was
always read. Fix this by ignoring the column and only using the page
address.
I suspect this whole-page behavior is due to the controller's need to
read the entire page in order to generate correct ECC. In the non-ECC
case this could be optimized to use the column address, and to set the
read length to what is being requested rather than the length of an
entire page.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix sched.h references:
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: 'PF_MEMALLOC' undeclared (first use in this function)
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1328: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: 'PF_MEMALLOC' undeclared (first use in this function)
build-r7149.out:make[4]: *** [drivers/mtd/nand/nandsim.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD has recently been upgraded for 64-bit support, see commit
number 69423d99fc in the
mtd-2.6.git tree (git://git.infradead.org/mtd-2.6.git)
or see this URL:
http://git.infradead.org/mtd-2.6.git?a=commit;h=69423d99fc182a81f3c5db3eb5c140acc6fc64be
Some variables in MTD data structures which were 32-bit
became 64-bit. Namely, the 'size' field in 'struct mtd_info'
and the 'addr'/'len' fields in 'struct erase_info'. This
means we have to use 'do_div' to divide them.
This patch fixes the following linking error:
ERROR: "__umoddi3" [drivers/mtd/devices/m25p80.ko] undefined!
This patch changes divisions of 64-bit variable so that they use
'do_div'. This patch also change some print placeholders to
get rid of gcc warnings.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Michał Mirosław