Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
This commits makes the intel_soc_pmic_core code check the _HRV of the
ACPI-firmware-node and selects intel_soc_pmic_config_byt_crc resp.
intel_soc_pmic_config_cht_crc based on this.
This fixes the Bay Trail specific ACPI OpRegion code causing problems
on Cherry Trail devices. Specifically this was causing the external
microsd slot on a Dell Venue 8 5855 (Cherry Trail version) to not work
and the eMMC to become unreliable and throw lots of errors.
Fixes: 5165238460 ("mfd: intel_soc_pmic: Core driver")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
Looking at the android x86 kernel sources where most of the Crystal Cove
code comes from, it talks about "Valley View", "Bay Trail" and / or BYT
without ever mentioning Cherry Trail, with the exception of the regulator
driver. The Asus Zenfone-2 kernel code has 2 regulator drivers, one
for Crystal Cove and one for what it calls Crystal Cove Plus. The
Crystal Cove Plus regulator driver is the only one to mention Cherry
Trail and that driver uses different register addresses then the
normal (Bay Trail) Crystal Cove regulator driver, showing that at
least the regulator register addresses are different.
The GPIO code should work on both, and the PWM code is known to work on
both and is necessary for backlight control on some Cherry Trail devices.
Testing has shown that the ACPI OpRegion code otoh is causing problems
on Cherry Trail devices, which is not surprising as it deals with the
regulators and those have different register addresses on CHT.
Specifically the ACPI OpRegion code causes the external microsd slot on
a Dell Venue 8 5855 (Cherry Trail version) to not work and the eMMC to
become unreliable and throw lots of errors.
This commit replaces the single mfd_cell array currently used for Crystal
Cove with 2 separate arrays, one for the Bay Trail variant and one for
the Cherry Trail variant, note that the Cherry Trail version of the array
only contains gpio and pwm cells. The PMIC OpRegion cell is deliberately
not included and drivers for the other cells in the Bay Trail cell array
were never upstreamed.
Fixes: 7cf0a66f32 ("mfd: intel_soc_pmic: Crystal Cove support")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
gcc-8 notices that the register number calculation is wrong
when the offset is an 'u8' but the number is larger than 256:
drivers/mfd/omap-usb-tll.c: In function 'omap_tll_init':
drivers/mfd/omap-usb-tll.c:90:46: error: overflow in conversion from 'int' to 'u8 {aka unsigned char}' chages value from 'i * 256 + 2070' to '22' [-Werror=overflow]
This addresses it by always using a 32-bit offset number for
the register. This is apparently an old problem that previous
compilers did not find.
Fixes: 16fa3dc75c ("mfd: omap-usb-tll: HOST TLL platform driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
spi_device_id are not supposed to change at runtime. All functions
working with spi_device_id provided by <linux/i2c.h> work with
const spi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 274e43edcd ("mfd: intel-lpss: Do not put device in reset
state on suspend") changed the behavior on suspend by not putting LPSS
controllers into reset. This was done because S3/S0ix fail if UART
device is put into reset and no_console_suspend flag is enabled.
Because of the above change, I2C controller gets into a bad state if
it observes that the I2C lines are pulled low when power to I2C device
is cut off during suspend (generally, I2C lines are pulled to power
rail of the I2C device in order to ensure that there is no leakage
because of the pulls when device is turned off). This results in the
controller timing out for all future I2C operations after resume. It
is primarily because of the following sequence of operations:
During suspend:
1. I2C controller is disabled, but it is not put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.
==> At this point the I2C controller gets into a bad state
On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled.
However, even after enabling the I2C controller, all future I2C xfers
fail since the controller is in a bad state and does not attempt to
make any transactions and hence times out.
In order to ensure that the controller does not get into a bad state,
this change puts it into reset if the controller type is not
UART. With this change, the order of operations is:
During suspend:
1. I2C controller is disabled and put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.
On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled and taken out of reset.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a missing PCI ID of the Intel Sunrise Point chipset to the Intel LPSS driver.
It fixes a bug causing the touchpad of the Lenovo Yoga 720-15 not to be recognized.
See also bug 1700657 on bugs.launchpad.net.
Many thanks to CoolStar, who found this solution!
Reported-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: Mike Schwartz <mykesx@gmail.com>
Tested-by: Björn Dahlgren <bjodah@gmail.com>
Signed-off-by: Florian R. Hölzlwimmer <git.ich@frhoelzlwimmer.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
we must disable clock, if t7l66xb_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PMIC provides ACPI OpRegions which must be available for other
drivers' PS0 / PS3 methods early-on as such it must be builtin as the
Kconfig help text already states.
Somehow its Kconfig option ended up being a tristate though, this fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes missing mfd_remove_devices() call when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TPS68470 device is an advanced power management
unit that powers a Compact Camera Module (CCM),
generates clocks for image sensors, drives a dual
LED for Flash and incorporates two LED drivers for
general purpose indicators.
This patch adds support for TPS68470 mfd device.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
At least on Lenovo Thinkpad Yoga, the BIOS seems to monitor the SPI-NOR
write protection bit and if it is flipped to read/write it assumes the
BIOS configuration was changed on next reboot. It then, for unknown
reasons, resets the BIOS settings back to default.
We can prevent this by just leaving the write protection bit intact and
let the SPI-NOR driver know whether the device is writable or not. In
case of this particular Lenovo the SPI-NOR flash will be exposed as
read-only.
Fixes: ff00d7a32a ("mfd: lpc_ich: Add support for SPI serial flash host controller")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195951
Reported-by: Abdó Roig-Marange <abdo.roig@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22e ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to their datasheets, the AXP221, AXP223, AXP288, AXP803,
AXP809 and AXP813 PEK have different values for startup time bits from
the AXP20X, let's use the platform device id with the correct values.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP813 PMIC is normally used with Allwinner's A83T SoC.
It has the same range of functions as other X-Powers PMICs, such as
DC-DC buck converter and linear regulator outputs, AC-IN and VBUS
power supplies, power button trigger, GPIOs, ADCs, and a battery
charger.
Note that the IRQ table given in the datasheet is incorrect: in IRQ
enable/status registers 1, there are separate IRQs for ACIN and VBUS,
instead of bits [7:5] being the same as bits [4:2]. So it shares the
same IRQs as the AXP803, rather than the AXP288.
This patch adds basic mfd support for it, with only the power button
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the MFD part of the ROHM BD9571MWV-M PMIC driver and MAINTAINERS
entry. The MFD part only specifies the regmap bits for the PMIC and
binds the subdevs together.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for HiSilicon Hi6421v530 PMIC. Hi6421v530 communicates with
main SoC via memory-mapped I/O.
Hi6421v530 and Hi6421 are PMIC chips from the same vendor, HiSilicon,
but at different revisions. They share the same memory-mapped I/O
design. They differ in integrated devices, such as regulator details,
LDO voltage points.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update dev_err messages to make them more readable.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change license text to a shorter form of GPLv2.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MTF_CORE should be enabled when driver is enabled.
Without this patch you can configure:
CONFIG_MFD_CORE is not set
CONFIG_MFD_TPS65086=y
... which ends up with compilation error:
drivers/mfd/tps65086.o: In function `tps65086_probe':
drivers/mfd/tps65086.c:110: undefined reference to `mfd_add_devices'
drivers/mfd/tps65086.c:110:(.text+0x128): relocation truncated to fit: \
R_AARCH64_CALL26 against undefined symbol `mfd_add_devices'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
16298 1009 184 17491 4453 drivers/mfd/ab8500-core.o
File size After adding 'const':
text data bss dec hex filename
16490 817 184 17491 4453 drivers/mfd/ab8500-core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
if 'max8998_i2c_parse_dt_pdata() fails (when out of memory), a NULL
pointer dereference will occur in the error handling code.
Return directly instead.
Fixes: ee999fb3f17f("mfd: max8998: Add support for Device Tree")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Drop static on a local variable, when the variable is initialized before
any use, on every possible execution path through the function. The static
has no benefit, and dropping it reduces the code size.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
The change in code size is indicates by the following output from the size
command.
before:
text data bss dec hex filename
2579 240 16 2835 b13 drivers/mfd/max8925-i2c.o
after:
text data bss dec hex filename
2531 240 8 2779 adb drivers/mfd/max8925-i2c.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is possible that under heavy system load, the counter in the completion
struct, used for waiting for end of AD conversion, gets incremented twice.
To make sure the driver recovers from this situation, the completion struct
should be reinitialized.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't populate the arrays depath and cd_mask on the stack but make
them static const. Makes the object code smaller:
text data bss dec hex filename
25413 7216 448 33077 8135 drivers/mfd/rtsx_pcr.o
text data bss dec hex filename
25151 7360 448 32959 80bf drivers/mfd/rtsx_pcr.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Saying it "returns the result" seems tautological. The read function
does not return num_bytes on success, it returns zero on success. I
noticed this discrepancy because some of the callers were checking for
>= 0.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 Low-Power Timer hardware block can be used for:
- PWM generation
- IIO trigger (in sync with PWM)
- IIO quadrature encoder counter
PWM and IIO timer configuration are mixed in the same registers so
we need a multi fonction driver to be able to share those registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- New driver for Lantiq CPU temperature sensor
- New driver for IBM CFF power supply
- New PMBus driver for TPS53679
- Add support for LM5066I lm25066 PMBus driver
- Add support for Intel VID protocol VR13 to PMBus drivers
- Add support for CAT34TS02C, GT30TS00, GT34TS02, and CAT34TS04 to jc42 driver
- Cleanup and minor improvements in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DZJP
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new drivers:
- Lantiq CPU temperature sensor
- IBM CFF power supply
- TPS53679 PMBus driver
- new support:
- LM5066I (lm25066 PMBus driver)
- Intel VID protocol VR13 (PMBus drivers)
- CAT34TS02C, GT30TS00, GT34TS02, and CAT34TS04 (jc42 driver)
- cleanup and minor improvements in several drivers
* tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (36 commits)
hwmon: (ltq-cputemp) add cpu temp sensor driver
hwmon: (ltq-cputemp) add devicetree bindings documentation
hwmon: (pmbus) Add support for Texas Instruments tps53679 device
hwmon: (asc7621) make several arrays static const
hwmon: (pmbus/lm25066) Add support for TI LM5066I
hwmon: (pmbus/lm25066) Offset coefficient depends on CL
hwmon: (pmbus) Add support for Intel VID protocol VR13
Documentation: hwmon: Document the IBM CFF power supply
hwmon: (pmbus) Add IBM Common Form Factor (CFF) power supply driver
dt-bindings: hwmon: Document the IBM CCF power supply version 1
hwmon: (ftsteutates) constify i2c_device_id
hwmon: da9052: Add support for TSI channel
mfd: da9052: Make touchscreen registration optional
hwmon: da9052: Replace S_IRUGO with 0444
mfd: da9052: Add register details for TSI
hwmon: (aspeed-pwm) add THERMAL dependency
hwmon: (pmbus) Add debugfs for status registers
hwmon: (aspeed-pwm-tacho) cooling device support.
Documentation: dt-bindings: aspeed-pwm-tacho cooling device.
hwmon: (pmbus): Add generic alarm bit for iin and pin
...
* pm-cpufreq: (33 commits)
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpufreq: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
cpufreq: dbx500: Delete obsolete driver
mfd: db8500-prcmu: Get rid of cpufreq dependency
cpufreq: enable the DT cpufreq driver on the Ux500
cpufreq: Loongson2: constify platform_device_id
cpufreq: dt: Add r8a7796 support to to use generic cpufreq driver
cpufreq: remove setting of policy->cpu in policy->cpus during init
cpufreq: mediatek: add support of cpufreq to MT7622 SoC
cpufreq: mediatek: add cleanups with the more generic naming
cpufreq: rcar: Add support for R8A7795 SoC
cpufreq: dt: Add rk3328 compatible to use generic cpufreq driver
cpufreq: s5pv210: add missing of_node_put()
cpufreq: Allow dynamic switching with CPUFREQ_ETERNAL latency
...
A small number of bugfixes, again nothing serious.
- Alexander Dahl found multiple bugs in the Atmel memory interface driver
- A randconfig build fix for at91 was incomplete, the second
attempt fixes the remaining corner case
- One fix for the TI Keystone queue handler
- The Odroid XU4 HDMI port (added in 4.13) needs a small
DT fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=efYA
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A small number of bugfixes, again nothing serious.
- Alexander Dahl found multiple bugs in the Atmel memory interface
driver
- A randconfig build fix for at91 was incomplete, the second attempt
fixes the remaining corner case
- One fix for the TI Keystone queue handler
- The Odroid XU4 HDMI port (added in 4.13) needs a small DT fix"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: add needs-hpd for Odroid-XU3/4
ARM: at91: don't select CONFIG_ARM_CPU_SUSPEND for old platforms
soc: ti: knav: Add a NULL pointer check for kdev in knav_pool_create
memory: atmel-ebi: Fix smc cycle xlate converter
memory: atmel-ebi: Allow t_DF timings of zero ns
memory: atmel-ebi: Fix smc timing return value evaluation
The ARMSS clock, also known as the operating point of the
CPU, should not cross-depend on cpufreq like this. Move
the code to use just frequencies and remove the false
frequency (1GHz) and put in the actual frequency provided
by the ARMSS clock (998400000 Hz) as part of the process.
After this and the related cpufreq patch, the DB8500 will
simply use the standard DT cpufreq driver to change the
operating points through the common clock framework using
the ARMSS clock.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch was applied to the MFD twice, causing unwanted behavour.
This reverts commit b77eb79acc.
Fixes: b77eb79acc ("mfd: da9061: Fix to remove BBAT_CONT register from chip model")
Reported-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the touchscreen pins are used as general purpose analogue
input, the touchscreen driver should not be used. The pins
will be handled by the existing hwmon driver instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK805 chip is a Power Management IC (PMIC) for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clocking
Both RK808 and RK805 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
the rk8xx chip id is:
((MSB << 8) | LSB) & 0xfff0
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The converter function for translating ns timings in register values was
initialized with a wrong function pointer. This resulted in wrong
register values also for the setup and pulse registers when configuring
the EBI interface trough dts.
Includes a small fix in a comment of the smc driver, which was probably
just a copy'n'paste mistake.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have a
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have a
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's not correct to encode the subsystem in the I2C device name, so
drop the -mfd suffix. To maintain bisect-ability, change driver and
platform code / DTS users in the same patch.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Changes in this pull request are around catching up
cros_ec with the internal chromeos-kernel versions of
cros_ec, cros_ec_lpc, and cros_ec_lightbar.
Also, switching maintainership from olof to bleung.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QtSr
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
"Changes in this pull request are around catching up cros_ec with the
internal chromeos-kernel versions of cros_ec, cros_ec_lpc, and
cros_ec_lightbar.
Also, switching maintainership from olof to bleung"
* tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome : Add myself as Maintainer
platform/chrome: cros_ec_lightbar - hide unused PM functions
cros_ec: Don't signal wake event for non-wake host events
cros_ec: Fix deadlock when EC is not responsive at probe
cros_ec: Don't return error when checking command version
platform/chrome: cros_ec_lightbar - Avoid I2C xfer to EC during suspend
platform/chrome: cros_ec_lightbar - Add userspace lightbar control bit to EC
platform/chrome: cros_ec_lightbar - Control of suspend/resume lightbar sequence
platform/chrome: cros_ec_lightbar - Add lightbar program feature to sysfs
platform/chrome: cros_ec_lpc: Add MKBP events support over ACPI
platform/chrome: cros_ec_lpc: Add power management ops
platform/chrome: cros_ec_lpc: Add support for GOOG004 ACPI device
platform/chrome: cros_ec_lpc: Add support for mec1322 EC
platform/chrome: cros_ec_lpc: Add R/W helpers to LPC protocol variants
mfd: cros_ec: Add support for dumping panic information
cros_ec_debugfs: Pass proper struct sizes to cros_ec_cmd_xfer()
mfd: cros_ec: add debugfs, console log file
mfd: cros_ec: Add EC console read structures definitions
mfd: cros_ec: Add helper for event notifier.
Pull input updates from Dmitry Torokhov:
- a new driver for STM FingerTip touchscreen
- a new driver for D-Link DIR-685 touch keys
- updated list of supported devices in xpad driver
- other assorted updates and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (23 commits)
MAINTAINERS: update input subsystem patterns
Input: introduce KEY_ASSISTANT
Input: xpad - sync supported devices with XBCD
Input: xpad - sync supported devices with 360Controller
Input: xen-kbdfront - use string constants from PV protocol
Input: stmfts - mark all PM functions as __maybe_unused
Input: add support for the STMicroelectronics FingerTip touchscreen
Input: add D-Link DIR-685 touchkeys driver
Input: s3c2410_ts - handle return value of clk_prepare_enable
Input: axp20x-pek - add wakeup support
Input: synaptics-rmi4 - use %phN to form F34 configuration ID
Input: synaptics-rmi4 - change a char type to u8
Input: sparse-keymap - remove sparse_keymap_free()
Input: tsc2007 - move header file out of I2C realm
Input: mms114 - move header file out of I2C realm
Input: mcs - move header file out of I2C realm
Input: lm8323 - move header file out of I2C realm
Input: elantech - force relative mode on a certain module
Input: elan_i2c - add support for fetching chip type on newer hardware
Input: elan_i2c - check if device is there before really probing
...
Pull MFD updates from Lee Jones:
"New Drivers:
- Intel Cherry Trail Whiskey Cove PMIC
- TI LP87565 PMIC
New Device Support:
- Add support for Cannonlake to intel-lpss-pci
- Add support for Simatic IOT2000 to intel_quark_i2c_gpio
New Functionality:
- Add Regulator support (axp20x)
Fix-ups:
- Rework IRQ handling (intel_soc_pmic_bxtwc, rtsx_pcr, cros_ec)
- Remove unused/unwelcome code (ipaq-micro, wm831x-core, da9062-core)
- Provide deregistration on unbind (rn5t618)
- Rework DT code/documentation (arizona)
- Constify things (fsl-imx25-tsadc)
- MAINTAINERS updates (DA9062/61)
- Kconfig configuration adaptions (INTEL_SOC_PMIC, MFD_AXP20X_I2C)
- Switch to DMI matching (intel_quark_i2c_gpio)
- Provide an appropriate level of error checking (wm831x-{i2c,spi},
twl4030-irq, tc6393xb)
- Make use of devm_* (resource handling) calls (intel_soc_pmic_bxtwc,
stm32-timers, atmel-flexcom, cros_ec, fsl-imx25-tsadc,
exynos-lpass, palmas, qcom-spmi-pmic, smsc-ece1099,
motorola-cpcap)"
[ Skipped the last commit in that series that added eight thousand
lines of pointless repeated register definitions. - Linus ]
* tag 'mfd-next-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (38 commits)
mfd: Add LP87565 PMIC support
mfd: cros_ec: Free IRQ on exit
dt-bindings: vendor-prefixes: Add arctic to vendor prefix
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: axp20x-i2c: Document that this must be builtin on x86
mfd: Add Cherry Trail Whiskey Cove PMIC driver
mfd: tc6393xb: Handle return value of clk_prepare_enable
mfd: intel_quark_i2c_gpio: Add support for SIMATIC IOT2000 platform
mfd: intel_quark_i2c_gpio: Use dmi_system_id table for retrieving frequency
mfd: motorola-cpcap: Use devm_of_platform_populate()
mfd: smsc-ece: Use devm_of_platform_populate()
mfd: qcom-spmi-pmic: Use devm_of_platform_populate()
mfd: palmas: Use devm_of_platform_populate()
mfd: exynos: Use devm_of_platform_populate()
mfd: fsl-imx25: Use devm_of_platform_populate()
mfd: cros_ec: Use devm_of_platform_populate()
mfd: atmel: Use devm_of_platform_populate()
mfd: stm32-timers: Use devm_of_platform_populate()
mfd: intel_soc_pmic: Select designware i2c-bus driver
...
The LP87565 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Configurable Bucks(Single and multi-phase).
- Configurable General Purpose Output Signals (GPO).
The LP87565-Q1 variant device uses two 2-phase outputs configuration,
Buck0 is master for Buck0/1 output and Buck2 is master for Buck2/3
output.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently we request the irq when probing, but never free it. So after
unbind ec driver, this irq will be left requested, which would break
the next bind:
[ 2683.338437] genirq: Flags mismatch irq 64. 00002008 (chromeos-ec) vs. 00002008 (chromeos-ec)
[ 2683.338591] cros-ec-spi spi5.0: request irq 64: error -16
[ 2683.338610] cros-ec-spi spi5.0: cannot register EC
[ 2683.338656] cros-ec-spi: probe of spi5.0 failed with error -16
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].
This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.
This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].
This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.
This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On x86 the AXP288 PMIC provides an ACPI OpRegion handler, which must be
available before other drivers using it are loaded, which can only be
ensured if the MFD, OpRegion and i2c-bus drivers are built-in.
Since the AXP20x MFD code is used on non x86 too we cannot simply change
this into a bool, I've tried some Kconfig magic with if x86 but I could
not get this working correctly, so this commit just documents that this
should be built-in on x86, which fixes errors like these during boot:
mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion]
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-2
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b
acpi 80860F14:02: Failed to change power state to D0
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add mfd driver for Intel CHT Whiskey Cove PMIC, based on various non
upstreamed CHT Whiskey Cove PMIC patches.
This is a somewhat minimal version which adds irqchip support and cells
for: ACPI PMIC opregion support, the i2c-controller driving the external
charger irc and the pwrsrc/extcon block.
Further cells can be added in the future if/when drivers are upstreamed
for them.
[The above patch caused a build error on some archetectures]
From: Arnd Bergmann <arnd@arndb.de>
I ran into a build error on ARM with a platform that has a non-standard
clk implementation:
drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here
The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.
This turns all three into 'depends on', as it should be.
Finally, we can limit the build to x86, unless we are compile testing.
First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The SIMATIC IOT2020 and IOT2040 are derived from the Galileo Gen2 board
and share its I2C frequency.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Avoids reimplementation of DMI matching in intel_quark_i2c_setup.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Usage of devm_of_platform_populate() simplify driver code
by allowing to delete cpcap_remove().
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Usage of devm_of_platform_populate() simplify driver code
by allowing to delete pmic_spmi_remove().
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() instead of of_platform_populate()
and suppress stm32_timers_remove() which become useless.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Crystal Cove PMIC provides an ACPI OPRegion handler, which must be
available before other drivers using it are loaded, which is why
INTEL_SOC_PMIC is a bool.
Just having the driver is not enough, the driver for the i2c-bus must
also be built in, to ensure this, this patch adds a select for it.
This fixes errors like these during boot:
mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion] (20170119/evregion-166)
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-299)
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93543b0cde10), AE_NOT_EXIST (20170119/psparse-543)
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b0b5cd0), AE_NOT_EXIST (20170119/psparse-543)
acpi 80860F14:02: Failed to change power state to D0
While at it this patch also changes the human readable name of the Kconfig
option to make clear the INTEL_SOC_PMIC option selects support for the
Intel Crystal Cove PMIC and documents why this is a bool.
[The above patch caused a build error on some archetectures]
From: Arnd Bergmann <arnd@arndb.de>
I ran into a build error on ARM with a platform that has a non-standard
clk implementation:
drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here
The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.
This turns all three into 'depends on', as it should be.
Finally, we can limit the build to x86, unless we are compile testing.
First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As silently failing isn't that nice, emit an error message at a place
that was silent on failure up to now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add NULL check before dereferencing pointer of_id in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1408830
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add NULL check before dereferencing pointer of_id in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1408829
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The request should be resent when DMA transfer error occurred.
For rts5227, the clock rate needs to be reduced when error occurred.
Signed-off-by: Steven Feng <steven_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As axp20x-regulator now supports AXP803, add a cell for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the restart handler registered in probe on device remove.
Fixes: a370f60a58 ("mfd: rn5t618: Register restart handler")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since a copy of the pdata was added into the core struct in
commit f6dd8449cd ("mfd: wm831x: Add basic device tree binding")
the pdata pointer in probe can no longer be NULL. As such remove
the redundant checks for this case.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These hexdumps get printed no matter if CONFIG_DEBUG is set or
not. Just get rid of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Cannonlake PCH has the same LPSS than Intel Kabylake. Add the new IDs
to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The subset of wake-enabled host events is defined by the EC, but the EC
may still send non-wake host events if we're in the process of
suspending. Get the mask of wake-enabled host events from the EC and
filter out non-wake events to prevent spurious aborted suspend
attempts.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Whishkey cove PMIC has support to mask/unmask interrupts at two levels.
At first level we can mask/unmask interrupt domains like TMU, GPIO, ADC,
CHGR, BCU THERMAL and PWRBTN and at second level, it provides facility
to mask/unmask individual interrupts belong each of this domain. For
example, in case of TMU, at first level we have TMU interrupt domain,
and at second level we have two interrupts, wake alarm, system alarm that
belong to the TMU interrupt domain.
Currently, in this driver all first level IRQs are registered as part of
IRQ chip(bxtwc_regmap_irq_chip). By default, after you register the IRQ
chip from your driver, all IRQs in that chip will masked and can only be
enabled if that IRQ is requested using request_irq() call. This is the
default Linux IRQ behavior model. And whenever a dependent device that
belongs to PMIC requests only the second level IRQ and not explicitly
unmask the first level IRQ, then in essence the second level IRQ will
still be disabled. For example, if TMU device driver request wake_alarm
IRQ and not explicitly unmask TMU level 1 IRQ then according to the default
Linux IRQ model, wake_alarm IRQ will still be disabled. So the proper
solution to fix this issue is to use the chained IRQ chip concept. We
should chain all the second level chip IRQs to the corresponding first
level IRQ. To do this, we need to create separate IRQ chips for every
group of second level IRQs.
In case of TMU, when adding second level IRQ chip, instead of using PMIC
IRQ we should use the corresponding first level IRQ. So the following
code will change from
ret = regmap_add_irq_chip(pmic->regmap, pmic->irq, ...)
to,
virq = regmap_irq_get_virq(&pmic->irq_chip_data, BXTWC_TMU_LVL1_IRQ);
ret = regmap_add_irq_chip(pmic->regmap, virq, ...)
In case of Whiskey Cove Type-C driver, Since USBC IRQ is moved under
charger level2 IRQ chip. We should use charger IRQ chip(irq_chip_data_chgr)
to get the USBC virtual IRQ number.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Revieved-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cleanup the resource allocation/free code in probe function by using
devm_* calls.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently all PMIC GPIO domain IRQs are consumed by the same
device(bxt_wcove_gpio), so there is no need to export them as
separate interrupts. We can just export only the first level
GPIO IRQ(BXTWC_GPIO_LVL1_IRQ) as an IRQ resource and let the
GPIO device driver(bxt_wcove_gpio) handle the GPIO sub domain
IRQs based on status value of GPIO level2 interrupt status
register. Also, just using only the first level IRQ will eliminate
the bug involved in requesting only the second level IRQ and not
explicitly enable the first level IRQ. For more info on this
issue please read the details at,
https://lkml.org/lkml/2017/2/27/148
This patch also makes relevant change in Whiskey cove GPIO driver to
use only first level PMIC GPIO IRQ.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since all second level thermal IRQs are consumed by the same
device(bxt_wcove_thermal), there is no need to expose them as separate
interrupts. We can just export only the first level IRQs for thermal and
let the device(bxt_wcove_thermal) driver handle the second level IRQs
based on thermal interrupt status register. Also, just using only the
first level IRQ will eliminate the bug involved in requesting only the
second level IRQ and not explicitly enable the first level IRQ. For
more info on this issue please read the details at,
https://lkml.org/lkml/2017/2/27/148
This patch also makes relevant change in bxt_wcove_thermal driver to use
only first level PMIC thermal IRQ.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TMU interrupts are registered as a separate interrupt chip, and
hence it should start its interrupt index(BXTWC_TMU_IRQ) number
from 0. But currently, BXTWC_TMU_IRQ is defined as part of enum
bxtwc_irqs_level2 and its index value is 11. Since this index
value is used when calculating .num_irqs of regmap_irq_chip_tmu,
it incorrectly reports number of IRQs as 12 instead of actual
value of 1.
This patch fixes this issue by creating new enum of tmu IRQs and
resetting its starting index to 0.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This enables configuring the PMIC's sleep mode via device-tree.
A pointer indirection to sleep mode data is removed, as it simplifies
the implementation slightly. In current kernel tree, platform data
structure is not used outside MFD cell drivers.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
A hardcoded register is accidentally used instead of the register
address passed into the function. Correct this and use the appropriate
variable. This would cause minor issues on wm5102, but all other
devices using this driver would have been unaffected.
Fixes: commit ef84f885e0 ("mfd: arizona: Refactor arizona_poll_reg")
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZK2lrAAoJEHm+PkMAQRiGm3AH/13F1DlIk05aSXHoDr/idIpR
GMHmk3YF+EuFjsL463Sh6s/SSWmz0Lda8euaoB4wCWvQFX2ZjTE+aOd79XlRiZJQ
OTtLkV9I41eXIJUpEOHia7xZiCsbw+usqcHrm1aBoSh5KKV2iQmEOrnJdibqJVOF
eXUMphNK/zFtAd2bKtQSxkaBnOOqsQUgVQSkr2K9rSg25l0KokFC6c5K5IjLn4x9
QgDY4wmMvHrDz0CtpoqlNM4XqbsDJVrFeZGfg6hlMqSRDeXeg4h3Ol0VfIT496RP
QBdrDb6hWO+HKt9B0M+7Q+8a/Fsw+5dtpqv1W/Wlr0i4CS6euU8NChAmrpkrqGo=
=m5ba
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc3' into next
Sync with mainline to bring in changes in platform drovers dropping
calls to sparse_keymap_free() so that we can remove it for good.
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
AXP803 is a new PMIC chip produced by X-Powers, usually paired with A64
via RSB bus. The PMIC itself is like AXP288, but with RSB support and
dedicated VBUS and ACIN.
Add support for it in the axp20x mfd driver.
Currently only power key function is supported.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
unction devm_regmap_init_i2c() returns an ERR_PTR on errors, and its
return value should be checked before it is dereferenced. However, in
function intel_soc_pmic_i2c_probe(), the return value of function
devm_regmap_init_i2c() is used without validation. This patch fixes it.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since
commit e6229bec25 ("rtc: make rtc_update_irq callable with irqs enabled")
rtc_update_irq() is callable with irqs enabled, see the rtc drivers.
So update this accordingly.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The idle mode needs to be only disabled for UTMIAUTOIDLE while
ULPIAUTOIDLE can be enabled.
This matches the TLL_CHANNEL_CONF_i register configuration for ehci-tll
in the Motorola Linux kernel tree for Wrigley 3G LTE modem on droid 4
and the modem still stays responsive.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 16fa3dc75c ("mfd: omap-usb-tll: HOST TLL platform driver")
added support for USB TLL, but uses OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
bit the wrong way. The comments in the code are correct, but the inverted
use of OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF causes the register to be
enabled instead of disabled unlike what the comments say.
Without this change the Wrigley 3G LTE modem on droid 4 EHCI bus can
be only pinged few times before it stops responding.
Fixes: 16fa3dc75c ("mfd: omap-usb-tll: HOST TLL platform driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed a small spelling mistake ("updat" -> "update") in an error message.
Signed-off-by: Willis Monroe <willismonroe@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Like Intel Apollo Lake, Gemini Lake exposes the serial SPI flash device BAR
through hidden P2SB PCI device. We use the same mechanism than Apollo Lake
to read the BAR and pass it to the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The hi655x is a PMIC with regulator but also provides a clock for the WiFi
and the bluetooth which is missing in the current implementation.
Add the clock cell so it can be used in the next patch via the dts.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Crystal Cove and Whiskey Cove are two different PMICs which are
installed on Intel Atom SoC based platforms.
Moreover there are two independent drivers that by some reason were
supposed (*) to get into one kernel module.
Fix the mess by clarifying Kconfig option for Crystal Cove and split
Whiskey Cove out of it.
(*) It looks like the configuration was never tested with
INTEL_SOC_PMIC=n. The line in Makefile is actually wrong.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert exisitng lpass-suspend/resume callbacks into runtime PM callbacks.
This way Exynos LPASS driver will be ready for use with power domains
enabled. LPASS will be runtime resumed/suspended as a result of its child
devices runtime PM transitions.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Disable device on driver remove and release allocated regmap.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Exynos LPASS requires some clocks to be enabled to make any access to its
registers. This patch adds code for handling such clocks. For current set
of registers it is enough to keep sfr0_ctrl clock enabled. Till now it
worked only because those clocks were enabled by bootloader and driver
probe() happened before they were disabled by clock core because of lack
of users. Handling those clocks is also needed to make it possible to
enable support for audio power domain.
This patch requires adding sfr0_ctrl clock to device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pad retention should be controlled from pin control driver, so remove it
from Exynos LPASS driver. After this change, no more access to PMU regmap
is needed, so remove also the code for handling PMU regmap.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cpcap INTS registers are for getting the value of the line,
not for configuring the type.
Fixes: 56e1d40d3b ("mfd: cpcap: Add minimal support")
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We should use ack_invert as the int_read_and_clear() in the Motorola
kernel tree does "ireg_val & ~mreg_val" before writing to the mask
register.
Fixes: 56e1d40d3b ("mfd: cpcap: Add minimal support")
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I made a mistake assuming the device tree configuration for interrupt
triggering was somehow passed to the SPI device but it's not.
In the Motorola Linux kernel tree CPCAP PMIC is configured as a rising
edge triggered interrupt, but then then it's interrupt handler keeps
looping until the GPIO line goes down. So the CPCAP interrupt is clearly
a level interrupt and not an edge interrupt.
Earlier when I tried to configure it as level interrupt using the
device tree, I did not account that the triggering only gets passed
to the SPI core and it also needs to be specified in the CPCAP driver
when we do devm_regmap_add_irq_chip().
Fixes: 56e1d40d3b ("mfd: cpcap: Add minimal support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP20X and AXP22X PMICs can have a battery as power supply.
This patch adds the AXP20X/AXP22X battery driver to the MFD cells of the
AXP209, AXP221 and AXP223 MFD.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD support for DA9061 is provided as part of the DA9062 device driver.
The registers header file adds two new chip variant IDs defined in DA9061
and DA9062 hardware. The core header file adds new software enumerations
for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
for distinguishing between DA9061/62 devices in software.
The core source code adds a new .compatible of_device_id entry. This is
extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
.data entry now holds a reference to the enumerated device type.
A new regmap_irq_chip model is added for DA9061 and this supports the new
list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
new sub system components for DA9061. Support is added for a new DA9061
regmap_config which lists the correct readable, writable and volatile
ranges for this chip.
The probe function uses the device tree compatible string to switch on the
da9062_compatible_types and configure the correct mfd cells, irq chip and
regmap config.
Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
GPIO bits clearing on pins assigned to STMPE1600
had no effects due to missing "clear registers"
settings within stmpe1600_regs[].
STMPE1600 does not have dedicated "clear registers",
but single "set/clear registers", hence stmpe1600_regs[]
"clear registers" (STMPE_IDX_GPCR_XXX) must be set to
same value as "set registers" (STMPE_IDX_GPSR_XXX), ie
STMPE1600_REG_GPSR_XXX.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the following code block, BXTWC_DEVICE1_ADDR value is
already fixed and hence there no need to check for
if (!i2c_addr) in every ipc read/write calls. Even if this
check is required it can be moved to probe function.
i2c_addr = BXTWC_DEVICE1_ADDR;
if (!i2c_addr) {
dev_err(pmic->dev, "I2C address not set\n");
return -EINVAL;
}
This patch remove this extra check and adds some NULL
parameter checks.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These new helpers + macro definitions are meant to replace the old ones
which are unpractical to use.
Note that the macros and function prefixes have been intentionally
changed to ATMEL_[H]SMC_XX and atmel_[h]smc_ to reflect the fact that
this IP is also embedded in avr32 SoCs (and not only in at91 ones).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
devm_ioremap_resource does checks on the resource. No need to
duplicate this in the driver.
Signed-off-by: Belén Sarabia <belensarabia@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
POWERHOLD signal has higher priority over the DEV_ON bit.
So power off will not happen if the POWERHOLD is held high.
Hence reset the MUX to GPIO_7 mode to release the POWERHOLD
and the DEV_ON bit to take effect to power off the PMIC.
PMIC Power off happens in dire situations like thermal shutdown
so irrespective of the POWERHOLD setting go ahead and turn off
the powerhold. Currently poweroff is broken on boards that have
powerhold enabled. This fixes poweroff on those boards.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The tc6393xb mfd driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The t7l66xb mfd driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The asic3 mfd driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For better understanding of relationship between headers and modules
rename:
intel_bxtwc.h -> intel_soc_pmic_bxtwc.h
While here, remove file name from the file itself.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to include intel_soc_pmic.h into header which doesn't
require it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, we specify the timeout in terms of the number of polls but it
is more clear from a user of the functions perspective to specify the
timeout directly in milliseconds, as such update the function to these new
semantics.
Additionally, arizona_poll_reg essentially hard-codes
regmap_read_poll_timeout, update the implementation to use
regmap_read_poll_timeout. We still keep arizona_poll_reg around as
regmap_read_poll_timeout is a macro so rather than expand this for each
caller keep it wrapped in arizona_poll_reg.
Whilst we are doing this make the timeouts a little more generous as
the previous system had a bit more slack as it was done as a delay per
iteration of the loop whereas regmap_read_poll_timeout compares ktime's.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Register addresses are normally displayed in hex throughout the Arizona
driver. Update the arizona_poll_reg function to follow this convention.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
arizona_poll_reg already returns ETIMEDOUT if we don't see the expected
register changes before the time out, so remove pointless local setting of
ETIMEDOUT.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/mfd
Prior to this patch, there were 4 uses of pr_warning and
9 uses of pr_warn in drivers/mfd
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Align the placement as which the mfd_cell of LED is defined as the other
members done on the structure.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The CHRG_CTRL1 and CHRG_CTRL2 registers are made for controlling
different battery charging settings such as the constant current charge
value.
The AXP22X also have a third register CHRG_CTRL3 which has settings for
battery charging too.
This adds the CHRG_CTRL1, CHRG_CTRL2 and CHRG_CTRL3 registers to the
list of writeable registers for AXP20X and AXP22X PMICs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP20X and AXP22X PMICs expose the status of AC power
supply.
This adds the AC power supply driver to the MFD cells of the AXP22X
PMICs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the AXP20X/AXP22x ADCs driver to the mfd cells of the AXP209,
AXP221 and AXP223 MFD.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The registers 0x56 and 0x57 of AXP22X PMIC store the value of the
internal temperature of the PMIC.
This patch modifies the name of these registers from AXP22X_PMIC_ADC_H/L
to AXP22X_PMIC_TEMP_H/L so their purpose is clearer.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The SPI interface is mostly a copy/paste from the I2C interface with some
minor renaming for consistency. "Client" is an I2C specific term that
was left in the SPI remove path, rename this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add Peripheral PHY Reset Controller to the Arria10
Development Kit System Resource Chip's MFD.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
After commit 028af5941d ("mfd: intel-lpss: Pass SDA hold time to
I2C host controller driver") the driver still has a non-used variable.
Remove it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a sucky change to bump up the time we'll wait for the EC. Why
is it sucky? If 200ms for a transfer is a common thing it will have a
massively bad impact on keyboard responsiveness.
It still seems like a good idea to do this, though, because we have a
gas gauge that claims that in an extreme case it could stretch the i2c
clock for 144ms. It's not a common case so it shouldn't affect
responsiveness, but it can happen. It's much better to have a single
slow keyboard response than to start returning errors when we don't
have to.
In newer EC designs we should probably implement a virtual battery to
respond to the kernel to insulate the kernel from these types of
issues.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TI LMU (Lighting Management Unit) driver supports lighting devices below.
LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
LMU devices have common features.
- I2C interface for accessing device registers
- Hardware enable pin control
- Backlight brightness control
- Notifier for hardware fault monitoring
- Regulators for LCD display bias
It contains fault monitor, backlight, LED and regulator driver.
LMU fault monitor
-----------------
LM3633 and LM3697 provide hardware monitoring feature.
It enables open or short circuit detection.
After monitoring is done, each device should be re-initialized.
Notifier is used for this case.
Separate patch for 'ti-lmu-fault-monitor' will be sent later.
Backlight
---------
It's handled by TI LMU backlight consolidated driver and
chip dependent data. Separate patchset will be sent later.
LED indicator
-------------
LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
supported. Separate patch for 'leds-lm3633' will be sent later.
Regulator
---------
LM3631 has 5 regulators for the display bias.
LM3632 supports 3 regulators. One consolidated driver enables it.
The lm363x regulator driver is already upstreamed.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. This patch lets the driver use the new device tree property
"xpowers,master-mode" to set the correct operating mode for the board.
Fixes: 8824ee8573 ("mfd: axp20x: Add support for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 845c877009 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") I2C core assigns interrupt line to I2C slave
devices with regarding to GpioInt() resources.
There is no need to repeat this in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 timers register bank size is 0x400. Fix regmap max_register.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is a debugging statement so make it be issued only then.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
At least two different omap3630/3730 boards booting from MMC1
fail to reboot if the "ti,twl4030-power-idle-osc-off" or
"ti,twl4030-power-idle" compatible flags are set. This patch will
keep the vmmc1 powered up during reboot allowing the bootloader
to load.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add missing of_platform_depopulate() upon driver removal.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patches adds the first minimal support to the upstream Linux tree.
Signed-off-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch installs an ACPI GPE handler for LID0 ACPI device to indicate
ACPI core that this GPE should stay enabled for lid to work in suspend
to idle path.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CPCAP can sense if IRQ is currently set or not. This
functionality is required for a few subdevices, such
as the power button and usb phy modules.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the basic ability to register the device through device tree, more
work is needed to get each individual sub-driver functioning correctly
but this is enough to get the device to probe from device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD-specific header will go away because it duplicates defines from
exynos-regs-pmu.h.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Assign iTCO_version which effectively enables watchdog device on
Intel Apollo Lake PCH.
Signed-off-by: Tan Jui Nee <jui.nee.tan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
First of all, remove stalled references to datasheets. If someone knows
the document numbers, it would be added later.
Second, remove FSF snail address since it's subject to change. Actual
information can be found on FSF site on the internet.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the DMI system ID of the Kontron COMe-bBD#, COMe-bKL6,
COMe-cKL6, COMe-bSL6 and COMe-cAL6 boards to the Kontron PLD driver. The
list of supported products in the module description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Christian Rauch <christian.rauch@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Declare regmap_irq_chip structures as const as they are only stored
in the regmap_irq_chip field of a rk808 structure. This field is of
type const, so regmap_irq_chip structures having this property can be
made const too.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct regmap_irq_chip x@p={...};
@ok@
struct rk808 a;
identifier r.x;
position p;
@@
a.regmap_irq_chip=&x@p;
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct regmap_irq_chip x;
File size before:
text data bss dec hex filename
5033 584 16 5633 1601 drivers/mfd/rk808.o
File size after:
text data bss dec hex filename
5225 392 16 5633 1601 drivers/mfd/rk808.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Many Motorola phones like droid 4 are using a custom PMIC called CPCAP
or 6556002. We can support it's core features quite easily with regmap_spi
and regmap_irq.
The children of cpcap, such as regulators, ADC and USB, can be just regular
device drivers and defined in the dts file. They get probed as we call
of_platform_populate() at the end of our probe, and then the children
can just call dev_get_regmap(dev.parent, NULL) to get the regmap.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Scott <michael.scott@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add compatible string as "mt6323-led" that will make
the OF core spawn child devices for the LED subnode
of that MT6323 MFD device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/mfd/tps65912-i2c.ko | grep alias
alias: i2c:tps65912
After this patch:
$ modinfo drivers/mfd/tps65912-i2c.ko | grep alias
alias: of:N*T*Cti,tps65912C*
alias: of:N*T*Cti,tps65912
alias: i2c:tps65912
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We didn't have proper device tree bindings for this clock,
I standardized it to use the exact chipname so let's rename
it "ab8500-clk" and rectify the device tree compatible string
to "stericsson,ab8500-clk".
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pm_suspend_via_firmware() will return false for platforms with ACPI
disabled and ACPI is a prerequisite for S0ix support.
With this patch, sleep state event sent to EC is forced to S3 if ACPI is
disabled.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver is only used in DT platforms so there's no need to
have an i2c_device_id table.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If a driver is only used in DT platforms, there's no need to get the
i2c_device_id as an argument of the probe function. Since this data
can be get from the matching of_device_id.
There's a temporary .probe_new field in struct i2c_driver that can be
used as probe callback for the case when i2c_device_id won't be used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the generic helper to get the matched of_device_id .data, instead of
open coding it.
The driver was checking if matching the OF node with the driver's OF table
was failing, but this doesn't make too much sense since this can't happen
in practice. The fact the probe function was called, means OF registered a
device with a valid compatible string so a of_device_get_match_data() call
will always succeed. So just remove this unneeded check.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver is only used in platforms that have DT support so always the
I2C device .data will be get from the matched OF node and never will be
from the I2C device ID table.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the current boot, clients making use of the AB8500 sysctrl
may be probed before the ab8500-sysctrl driver. This gives them
-EINVAL, but should rather give -EPROBE_DEFER.
Before this, the abx500 clock driver didn't probe properly,
and as a result the codec driver in turn using the clocks did
not probe properly. After this patch, everything probes
properly.
Also add OF compatible-string probing. This driver is all
device tree, so let's just make a drive-by-fix of that as
well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Gemini Lake is essentially Broxton with different PCI IDs. Add these
new PCI IDs to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 supports either master/standalone or slave mode.
Slave mode allows sharing the serial bus, even with multiple
AXP806 which all have the same hardware address.
This is done with extra "serial interface address extension",
or AXP806_BUS_ADDR_EXT, and "register address extension", or
AXP806_REG_ADDR_EXT, registers. The former is read-only, with
1 bit customizable at the factory, and 1 bit depending on the
state of an external pin. The latter is writable. Only when
the these device addressing bits (in the upper 4 bits of the
registers) match, will the device respond to operations on
its other registers.
The AXP806_REG_ADDR_EXT was previously configured by Allwinner's
bootloader. Work on U-boot SPL support now allows us to switch
to mainline U-boot, which doesn't do this for us. There might
be other bare minimum bootloaders out there which don't to this
either. It's best to handle this in the kernel.
This patch sets AXP806_REG_ADDR_EXT to 0x10, which is what we
know to be the proper value for a standard AXP806 in slave mode.
Afterwards it will reinitialize the regmap cache, to purge any
invalid stale values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Notify EC when going to or returning from suspend so that proper actions
related to wake events can be taken.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros_ec driver is still active while the device is suspended.
Besides that, it also tries to transfer data even after the I2C host had
been suspended. This patch uses a simple flag to prevent this.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD_SUN4I_GPADC and TOUCHSCREEN_SUN4I are incompatible (both are drivers
for Allwinner SoCs' ADC). This makes sure TOUCHSCREEN_SUN4I isn't
enabled while MFD_SUN4I_GPADC is enabled.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP223 shares most of its logic with the AXP221 but has some
differences for the VBUS power supply driver. Thus, to probe the driver
with the correct compatible, the AXP221 and the AXP223 now have separate
MFD cells.
AXP221 MFD cells are renamed from axp22x_cells to axp221_cells to avoid
confusion.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp288 pmic has a lot more volatile registers then we were
listing in axp288_volatile_ranges, fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The R in PEK_DBR stands for rising, so it should be mapped to
AXP288_IRQ_POKP where the last P stands for positive edge.
Likewise PEK_DBF should be mapped to the falling edge, aka the
_N_egative edge, so it should be mapped to AXP288_IRQ_POKN.
This fixes the inverted powerbutton status reporting by the
axp20x-pek driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp288 has the following irqs 2 times: VBUS_FALL, VBUS_RISE,
VBUS_OV. On boot / reset the enable flags for both the normal and alt
version of these irqs is set.
Since we were only listing the normal version in the axp288 regmap_irq
struct, we were never disabling the alt versions of these irqs.
Add the alt versions to the axp288 regmap_irq struct, so that these
get properly disabled.
Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The interrupt line of the entire family of axp2xx pmics is active-low,
for devicetree enumerated irqs, this is dealt with in the devicetree.
ACPI irq resources have a flag field for this too, I tried using this
on my CUBE iwork8 Air tablet, but it does not contain the right data.
The dstd shows the irq listed as either ActiveLow or ActiveHigh,
depending on the OSID variable, which seems to be set by the
"OS IMAGE ID" in the BIOS/EFI setup screen.
Since the acpi-resource info is no good, simply pass in IRQF_TRIGGER_LOW
on the axp288.
Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This declaration has never been used and is likely some left over from
early prototypes of the code, just remove it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PRCM block on the A23 contains a message box like interface to
the registers for the analog path controls of the internal codec.
Add a sub-device for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently we leak a lot of things when tearing down the IRQs this patch
fixes this cleaning up both the IRQ mappings and the IRQ domain itself.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We have arizona_map_irq we might as well use it rather than hard coding
it in several places.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This hardware block could at used at same time for PWM generation
and IIO timers.
PWM and IIO timer configuration are mixed in the same registers
so we need a multi fonction driver to be able to share those registers.
version 7:
- rebase on v4.10-rc2
version 6:
- rename files to stm32-timers
- rename functions to stm32_timers_xxx
version 5:
- fix Lee comments about detect function
- add missing dependency on REGMAP_MMIO
version 4:
- add a function to detect Auto Reload Register (ARR) size
- rename the structure shared with other drivers
version 2:
- rename driver "stm32-gptimer" to be align with SoC documentation
- only keep one compatible
- use of_platform_populate() instead of devm_mfd_add_devices()
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Apollo Lake SoC exposes serial SPI flash through the LPC device. The
SPI flash host controller is not discoverable through PCI config cycles
because P2SB (function 0 of the device 13) is hidden by the BIOS. We unhide
the device briefly in order to read BAR 0 of the SPI host controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Many Intel CPUs including Haswell, Broadwell and Baytrail have SPI serial
flash host controller as part of the LPC device. This will populate an MFD
cell suitable for the SPI host controller driver if we know that the LPC
device has one.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move and add registration for the mlx-platform driver. Introduce button and lid
drivers for the surface3 (different from the surface3-pro). Add BXT PMIC TMU
support. Add Y700 to existing ideapad-laptop quirk.
ideapad-laptop:
- Add Y700 15-ACZ to no_hw_rfkill DMI list
surface3_button:
- Introduce button support for the Surface 3
surface3-wmi:
- Add custom surface3 platform device for controlling LID
- Balance locking on error path
mlx-platform:
- Add mlxcpld-hotplug driver registration
- Fix semicolon.cocci warnings
- Move module from arch/x86
platform/x86:
- Add Whiskey Cove PMIC TMU support
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYVxXxAAoJEKbMaAwKp364mDAIAL750zoO/liY1qfFGktkY2zS
xknJqh4UeIVW6iN9hEq7jQD3jkFl7hNuXgFyogLZgJQge8gfufsOD7ljkhp2wVF2
3Ir437f4GdcUeuhO6PwuPZnn++Y6oH2rLZc1d+5anZRikW470tnXitrXs5hsqG57
74KiSFa+v+Uj1kqU4Gjt0QDSfmQc185Wn5xieHPpZrcjDaut+N4t06+MDMcH7fjk
6nJ+tvo/dreZojA+AklljaNB2BioIGbEOGamnxOJ9Rjs0jV2d0A1c/6XBHDe+Xtu
SkWqvjdrLOSxAjErBpB97VYnYihjCDXfl+DIABOdumGO6hJz01DvbZ+VVLwGM0E=
=YH31
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.10-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull more x86 platform driver updates from Darren Hart:
"Move and add registration for the mlx-platform driver. Introduce
button and lid drivers for the surface3 (different from the
surface3-pro). Add BXT PMIC TMU support. Add Y700 to existing
ideapad-laptop quirk.
Summary:
ideapad-laptop:
- Add Y700 15-ACZ to no_hw_rfkill DMI list
surface3_button:
- Introduce button support for the Surface 3
surface3-wmi:
- Add custom surface3 platform device for controlling LID
- Balance locking on error path
mlx-platform:
- Add mlxcpld-hotplug driver registration
- Fix semicolon.cocci warnings
- Move module from arch/x86
platform/x86:
- Add Whiskey Cove PMIC TMU support"
* tag 'platform-drivers-x86-v4.10-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: surface3-wmi: Balance locking on error path
platform/x86: Add Whiskey Cove PMIC TMU support
platform/x86: ideapad-laptop: Add Y700 15-ACZ to no_hw_rfkill DMI list
platform/x86: Introduce button support for the Surface 3
platform/x86: Add custom surface3 platform device for controlling LID
platform/x86: mlx-platform: Add mlxcpld-hotplug driver registration
platform/x86: mlx-platform: Fix semicolon.cocci warnings
platform/x86: mlx-platform: Move module from arch/x86
This adds TMU (Time Management Unit) support for Intel BXT platform.
It enables the alarm wake-up functionality in the TMU unit of Whiskey Cove
PMIC.
Signed-off-by: Nilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[andy: resolve merge conflict in Kconfig]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Pull i2c updates from Wolfram Sang:
- the first series of making i2c_device_id optional instead of
mandatory (in favor of alternatives like of_device_id).
This involves adding a new probe callback (probe_new) which removes
some peculiarities I2C had for a long time now. The new probe is
matching the other subsystems now and the old one will be removed
once all users are converted. It is expected to take a while but
there is ongoing interest in that.
- SMBus Host Notify introduced 4.9 got refactored. They are now using
interrupts instead of the alert callback which solves multiple
issues.
- new drivers for iMX LowPower I2C, Mellanox CPLD and its I2C mux
- significant refactoring for bcm2835 driver
- the usual set of driver updates and improvements
* 'i2c/for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (46 commits)
i2c: fsl-lpi2c: read lpi2c fifo size in probe()
i2c: octeon: thunderx: Remove double-check after interrupt
i2c: octeon: thunderx: TWSI software reset in recovery
i2c: cadence: Allow Cadence I2C to be selected for Cadence Xtensa CPUs
i2c: sh_mobile: Add per-Generation fallback bindings
i2c: rcar: Add per-Generation fallback bindings
i2c: imx-lpi2c: add low power i2c bus driver
dt-bindings: i2c: imx-lpi2c: add devicetree bindings
i2c: designware-pcidrv: Add 10bit address feature to medfield/merrifield
i2c: pxa: Add support for the I2C units found in Armada 3700
i2c: pxa: Add definition of fast and high speed modes via the regs layout
dt-bindings: i2c: pxa: Update the documentation for the Armada 3700
i2c: qup: support SMBus block read
i2c: qup: add ACPI support
i2c: designware: Consolidate default functionality bits
i2c: i2c-mux-gpio: update mux with gpiod_set_array_value_cansleep
i2c: mux: pca954x: Add ACPI support for pca954x
i2c: use an IRQ to report Host Notify events, not alert
i2c: i801: remove SMBNTFDDAT reads as they always seem to return 0
i2c: i801: use the BIT() macro for FEATURES_* also
...
Here's the "big" staging/iio pull request for 4.10-rc1.
Not as big as 4.9 was, but still just over a thousand changes. We
almost broke even of lines added vs. removed, as the slicoss driver was
removed (got a "clean" driver for the same hardware through the netdev
tree), and some iio drivers were also dropped, but I think we ended up
adding a few thousand lines to the source tree in the end. Other than
that it's a lot of minor fixes all over the place, nothing major stands
out at all.
All of these have been in linux-next for a while. There will be a merge
conflict with Al's vfs tree in the lustre code, but the resolution for
that should be pretty simple, that too has been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAk1Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymikACg05b0h/iVTTH18474PXXnzw6jk9IAn0gI2fx9
cqp2MglTvphhrXzddL7V
=MeTw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here's the "big" staging/iio pull request for 4.10-rc1.
Not as big as 4.9 was, but still just over a thousand changes. We
almost broke even of lines added vs. removed, as the slicoss driver
was removed (got a "clean" driver for the same hardware through the
netdev tree), and some iio drivers were also dropped, but I think we
ended up adding a few thousand lines to the source tree in the end.
Other than that it's a lot of minor fixes all over the place, nothing
major stands out at all.
All of these have been in linux-next for a while. There will be a
merge conflict with Al's vfs tree in the lustre code, but the
resolution for that should be pretty simple, that too has been in
linux-next"
* tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1002 commits)
staging: comedi: comedidev.h: Document usage of 'detach' handler
staging: fsl-mc: remove unnecessary info prints from bus driver
staging: fsl-mc: add sysfs ABI doc
staging/lustre/o2iblnd: Fix misspelled attemps->attempts
staging/lustre/o2iblnd: Fix misspelling intialized->intialized
staging/lustre: Convert all bare unsigned to unsigned int
staging/lustre/socklnd: Fix whitespace problem
staging/lustre/o2iblnd: Add missing space
staging/lustre/lnetselftest: Fix potential integer overflow
staging: greybus: audio_module: remove redundant OOM message
staging: dgnc: Fix lines longer than 80 characters
staging: dgnc: fix blank line after '{' warnings.
staging/android: remove Sync Framework tasks from TODO
staging/lustre/osc: Revert erroneous list_for_each_entry_safe use
staging: slicoss: remove the staging driver
staging: lustre: libcfs: remove lnet upcall code
staging: lustre: remove set but unused variables
staging: lustre: osc: set lock data for readahead lock
staging: lustre: import: don't reconnect during connect interpret
staging: lustre: clio: remove mtime check in vvp_io_fault_start()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4k30
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- userspace LED class driver - it can be useful for testing triggers
and can also be used to implement virtual LEDs
- LED class driver for NIC78bx device
- LED core fixes for preventing potential races while setting
brightness when software blinking is enabled
- improvements in LED documentation to mention semantics on changing
brightness while trigger is active
* tag 'leds_for_4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca955x: Add ACPI support
leds: netxbig: fix module autoload for OF registration
leds: pca963x: Add ACPI support
leds: leds-cobalt-raq: use builtin_platform_driver
led: core: Fix blink_brightness setting race
led: core: Use atomic bit-field for the blink-flags
leds: Add user LED driver for NIC78bx device
leds: verify vendor and change license in mlxcpld driver
leds: pca963x: enable low-power state
leds: pca9532: Use default trigger value from platform data
leds: pca963x: workaround group blink scaling issue
cleanup LED documentation and make it match reality
leds: lp3952: Export I2C module alias information for module autoload
leds: mc13783: Fix MC13892 keypad led access
ledtrig-cpu.c: fix english
leds/leds-lp5523.txt: make documentation match reality
tools/leds: Add uledmon program for monitoring userspace LEDs
leds: Use macro for max device node name size
leds: Introduce userspace LED class driver
mfd: qcom-pm8xxx: Clean up PM8XXX namespace
TPS65217 INT pin is used for the system wakeup from suspend mode.
This patch enables push button or charger input event as a wakeup source.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rework the IRQ handler by using HW IRQ number and status bit.
Each HW IRQ number is matched with TPS65217 register layout[*].
(USB IRQ number is 0, AC is 1, Push button is 2)
When an interrupt is enabled, mask bit should be cleared (unmasked).
If an interrupt is disabled, then mask bit should be set (masked).
This mask value is updated into the TPS65217 register in irq_sync_unlock().
Mask bit and interrupt status bit can be handled with HW IRQ number.
Eventually, additional IRQ data, 'tps65217_irqs[]' and the function,
'irq_to_tps65217_irq()' are not necessary.
[*] TPS65217 interrupt register layout
Bit7 6 5 4 3 2 1 0
----------------------------------------------
| x | PBM | ACM | USBM | x | PBI | ACI | USBI
PBM: Push button status change interrupt mask
ACM: AC interrupt mask
USBM: USB power status change interrupt mask
PBI: Push button status change interrupt
ACI: AC power status change interrupt
USBI: USB power status change interrupt
x: Not used
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TPS65217 interrupt register includes read/writeable mask bits with
read-only status bits. (bit 4, 5, 6 are R/W, bit 0, 1, 2 are RO)
And reserved bit is not required.
Register update operation is preferred for disabling all interrupts during
the device initialisation.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TPS65217 MFD is an interrupt controller and MFD slave devices like
tps65217-charger and tps65217-pwrbutton request an interrupt to handle
each HW event.
Currently, TPS65217 IRQ name is not defined, so the result is as below.
root@arm:~# cat /proc/interrupts
...
182: 0 INTC 7 Level tps65217-irq
183: 0 - 1 Edge tps65217-charger
185: 0 - 2 Edge tps65217_pwrbutton
This patch specifies the name of the interrupt controller.
182: 0 INTC 7 Level tps65217-irq
183: 0 tps65217 1 Edge tps65217-charger
185: 0 tps65217 2 Edge tps65217_pwrbutton
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
palmas_dev and palmas_power_off are always assigned together.
So the check for palmas_dev inside palmas_power_off function
is redundant. Removing the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As DCVDD will often be supplied by a child node of the MFD, we
can't call mfd_remove_devices as the first step in arizona_dev_exit
as might be expected (tidy up the children before we tidy up the
MFD). We need to disable and put the DCVDD regulator before we call
mfd_remove_devices, to prevent PM runtime from turning this back on we
also need to disable the PM runtime before we do this. Finally we can
not clean up the IRQs until all the MFD children have been removed, as
they may have registered IRQs themselves.
This creates a window of time where the interrupts are enabled but
the PM runtime, on which the IRQ handler depends, is not available,
any interrupts in this window will go unhandled and fill the log with
failed to resume device messages. To avoid this we simply disable the
main IRQ at the start of arizona_dev_exit, we don't need to actually
handle any IRQs in this window as we are removing the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support to PM8821 PMIC and interrupt support.
PM8821 is companion device that supplements primary PMIC PM8921 IC.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Enable MWI mechanism if PCI bus master supports it.
It might be potential benefit in some cases. Documentation [1] says that
standard Memory Write might supply more current data than in the CPU modified
cache line and "trashing a line in the cache may trash some data that is more
current that in the memory line". This allows to avoid potential retries and
other performance degradation issues on the bus.
[1] PCI System Architecture, 4th edition, ISBN: 0-201-30974-2, pp.117-119.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:
+ DCDC4/DCDC5
+ LDO7-10
+ Slightly different output voltage/currents
+ 32kHz Output
+ RTC
+ USB Charger detection
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 supports either master/standalone or slave mode.
Slave mode allows sharing the serial bus, even with multiple
AXP806 which all have the same hardware address.
This is done with extra "serial interface address extension",
or AXP806_BUS_ADDR_EXT, and "register address extension", or
AXP806_REG_ADDR_EXT, registers. The former is read-only, with
1 bit customizable at the factory, and 1 bit depending on the
state of an external pin. The latter is writable. Only when
the these device addressing bits (in the upper 4 bits of the
registers) match, will the device respond to operations on
its other registers.
Add these 2 registers to the regmap so we can access them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix a typo in MODULE_DEVICE_TABLE(). 'pmic_acpi_ids' should be
'bxtwc_acpi_ids'.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().
Fixes: a9bbba9963 ("mfd: add platform_device sharing support for mfd")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'i2c_new_dummy()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The new sun4i mfd driver is lacking a dependency, triggering very rarely
int randconfig kernel builds:
drivers/mfd/sun4i-gpadc.o: In function `sun4i_gpadc_probe':
sun4i-gpadc.c:(.text.sun4i_gpadc_probe+0x110): undefined reference to `devm_regmap_add_irq_chip'
This adds a 'select REGMAP_IRQ', as the other drivers with this problem do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config ABX500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We replace module.h with init.h and export.h -- the latter since the file
does make use of EXPORT_SYMBOL.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_GPADC
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 GPADC driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_DEBUG
drivers/mfd/Kconfig: bool "Enable debug info via debugfs"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB8500_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We replace module.h with moduleparam.h ; the latter since this file
was implicitly relying on getting it.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config AB3100_CORE
drivers/mfd/Kconfig: bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only. In doing
so, the debugfs unregister fcn becomes unused so we remove it too.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Trivial spelling mistake fixes in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
No need to use irq_create_mapping (although there is no issue with
doing so) when we are only looking up an existing mapping. Just to
streamline things a little and make the code a little more clear
change some calls from irq_create_mapping to irq_find_mapping.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The kernel WARNs and then crashes today if wm8994_device_init() fails
after calling devm_regulator_bulk_get().
That happens because there are multiple devices involved here and the
order in which managed resources are freed isn't correct.
The regulators are added as children of wm8994->dev. Whereas,
devm_regulator_bulk_get() receives wm8994->dev as the device, though it
gets the same regulators which were added as children of wm8994->dev
earlier.
During failures, the children are removed first and the core eventually
calls regulator_unregister() for them. As regulator_put() was never done
for them (opposite of devm_regulator_bulk_get()), the kernel WARNs at
WARN_ON(rdev->open_count);
And eventually it crashes from debugfs_remove_recursive().
Fix the kernel warnings and crashes by using regulator_bulk_get()
instead of devm_regulator_bulk_get() and explicitly freeing the supplies
in exit paths.
Tested on Exynos 5250, dual core ARM A15 machine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mach/hardware.h is needed on C source code side, not header.
And struct davinci_vc is duplicated definition.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the trailing spaces on the register default lines to
stop checkpatch complaining.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building for X86 using COMPILE_TEST we get this warning:
../drivers/mfd/sun4i-gpadc.c: In function ‘sun4i_gpadc_probe’:
../drivers/mfd/sun4i-gpadc.c:110:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Since an integer and a pointer are difference sizes on 64bit architectures.
Convert to case to a long instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The i2c subsys does not load modules by compatible, only by
i2c-id, with e.g. a modalias of: "i2c:axp209".
Populate the axp20x_i2c_id[] table with supported ids, so that
module auto-loading will work.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap devicetree binding documentation states that a native-endian
property should be supported as well as big-endian & little-endian,
however syscon in its duplication of the parsing of these properties
omits support for native-endian. Fix this by setting
REGMAP_ENDIAN_NATIVE when a native-endian property is found.
Cc: linux-mips@linux-mips.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tested-by: Maciej W. Rozycki <macro@imgtec.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that
only DEV_OFF_RST can power off supplies. RK818 has been fixed this
issue, so that DEV_OFF is used to power off supplies.
Signed-off-by: Jianhong Chen <chenjh@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mfd/fsl-imx25-tsadc.ko | grep alias
alias: platform:mx25-tsadc
After this patch:
$ modinfo drivers/mfd/fsl-imx25-tsadc.ko | grep alias
alias: platform:mx25-tsadc
alias: of:N*T*Cfsl,imx25-tsadcC*
alias: of:N*T*Cfsl,imx25-tsadc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mfd/hi655x-pmic.ko | grep alias
After this patch:
$ modinfo drivers/mfd/hi655x-pmic.ko | grep alias
alias: of:N*T*Chisilicon,hi655x-pmicC*
alias: of:N*T*Chisilicon,hi655x-pmic
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver only has runtime but no build time dependency with ARCH_U300 ||
ARCH_U8500 So it can be built for testing purposes if COMPILE_TEST option
is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver is meant for Exynos systems so do not offer the option
elsewhere unless build-testing.
Cc: Inha Song <ideal.song@samsung.com>
Cc: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building with extra warnings enabled, most files including
linux/mfd/tps65912.h warn about a static variable defined in the
header:
include/linux/mfd/tps65912.h:331:35: warning: 'tps65912_regmap_config' defined but not used [-Wunused-const-variable=]
We also duplicate the data structure between the i2c and spi front-end
drivers. Moving it into the driver code avoids the warning and
the duplication.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The order in which resources were freed in wm8994_device_exit() isn't
correct. The regulators are removed before they are disabled.
Fix it by reordering code a bit, which makes it exact opposite of
wm8994_device_init() as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These can fit in a single line (80 columns), don't split lines
unnecessarily.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The OF is not a strict build-time dependency so max77620 and max77686
can be compile tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the correct function name in one case and adjust a variable name to
that of the corresponding function parameter in another case.
Issue detected using Coccinelle (http://coccinelle.lip6.fr/)
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. For now, only the ADC and the thermal
sensor drivers are probed by the MFD, the touchscreen controller support
will be added later.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The kernel WARNs and then crashes today if wm8994_device_init() fails
after calling devm_regulator_bulk_get().
That happens because there are multiple devices involved here and the
order in which managed resources are freed isn't correct.
The regulators are added as children of wm8994->dev. Whereas,
devm_regulator_bulk_get() receives wm8994->dev as the device, though it
gets the same regulators which were added as children of wm8994->dev
earlier.
During failures, the children are removed first and the core eventually
calls regulator_unregister() for them. As regulator_put() was never done
for them (opposite of devm_regulator_bulk_get()), the kernel WARNs at
WARN_ON(rdev->open_count);
And eventually it crashes from debugfs_remove_recursive().
--------x------------------x----------------
wm8994 3-001a: Device is not a WM8994, ID is 0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /mnt/ssd/all/work/repos/devel/linux/drivers/regulator/core.c:4072 regulator_unregister+0xc8/0xd0
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.8.0-rc6-00154-g54fe84cbd50b #41
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c010e24c>] (unwind_backtrace) from [<c010af38>] (show_stack+0x10/0x14)
[<c010af38>] (show_stack) from [<c032a1c4>] (dump_stack+0x88/0x9c)
[<c032a1c4>] (dump_stack) from [<c011a98c>] (__warn+0xe8/0x100)
[<c011a98c>] (__warn) from [<c011aa54>] (warn_slowpath_null+0x20/0x28)
[<c011aa54>] (warn_slowpath_null) from [<c0384a0c>] (regulator_unregister+0xc8/0xd0)
[<c0384a0c>] (regulator_unregister) from [<c0406434>] (release_nodes+0x16c/0x1dc)
[<c0406434>] (release_nodes) from [<c04039c4>] (__device_release_driver+0x8c/0x110)
[<c04039c4>] (__device_release_driver) from [<c0403a64>] (device_release_driver+0x1c/0x28)
[<c0403a64>] (device_release_driver) from [<c0402b24>] (bus_remove_device+0xd8/0x104)
[<c0402b24>] (bus_remove_device) from [<c03ffcd8>] (device_del+0x10c/0x218)
[<c03ffcd8>] (device_del) from [<c0404e4c>] (platform_device_del+0x1c/0x88)
[<c0404e4c>] (platform_device_del) from [<c0404ec4>] (platform_device_unregister+0xc/0x20)
[<c0404ec4>] (platform_device_unregister) from [<c0428bc0>] (mfd_remove_devices_fn+0x5c/0x64)
[<c0428bc0>] (mfd_remove_devices_fn) from [<c03ff9d8>] (device_for_each_child_reverse+0x4c/0x78)
[<c03ff9d8>] (device_for_each_child_reverse) from [<c04288c4>] (mfd_remove_devices+0x20/0x30)
[<c04288c4>] (mfd_remove_devices) from [<c042758c>] (wm8994_device_init+0x2ac/0x7f0)
[<c042758c>] (wm8994_device_init) from [<c04f14a8>] (i2c_device_probe+0x178/0x1fc)
[<c04f14a8>] (i2c_device_probe) from [<c04036fc>] (driver_probe_device+0x214/0x2c0)
[<c04036fc>] (driver_probe_device) from [<c0403854>] (__driver_attach+0xac/0xb0)
[<c0403854>] (__driver_attach) from [<c0401a74>] (bus_for_each_dev+0x68/0x9c)
[<c0401a74>] (bus_for_each_dev) from [<c0402cf0>] (bus_add_driver+0x1a0/0x218)
[<c0402cf0>] (bus_add_driver) from [<c040406c>] (driver_register+0x78/0xf8)
[<c040406c>] (driver_register) from [<c04f20a0>] (i2c_register_driver+0x34/0x84)
[<c04f20a0>] (i2c_register_driver) from [<c01017d0>] (do_one_initcall+0x40/0x170)
[<c01017d0>] (do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
[<c0a00dbc>] (kernel_init_freeable) from [<c06e07b0>] (kernel_init+0x8/0x114)
[<c06e07b0>] (kernel_init) from [<c0107978>] (ret_from_fork+0x14/0x3c)
---[ end trace 0919d3d0bc998260 ]---
[snip..]
Unable to handle kernel NULL pointer dereference at virtual address 00000078
pgd = c0004000
[00000078] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.8.0-rc6-00154-g54fe84cbd50b #41
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
task: ee874000 task.stack: ee878000
PC is at down_write+0x14/0x54
LR is at debugfs_remove_recursive+0x30/0x150
[snip..]
[<c06e489c>] (down_write) from [<c02e9954>] (debugfs_remove_recursive+0x30/0x150)
[<c02e9954>] (debugfs_remove_recursive) from [<c0382b78>] (_regulator_put+0x24/0xac)
[<c0382b78>] (_regulator_put) from [<c0382c1c>] (regulator_put+0x1c/0x2c)
[<c0382c1c>] (regulator_put) from [<c0406434>] (release_nodes+0x16c/0x1dc)
[<c0406434>] (release_nodes) from [<c04035d4>] (driver_probe_device+0xec/0x2c0)
[<c04035d4>] (driver_probe_device) from [<c0403854>] (__driver_attach+0xac/0xb0)
[<c0403854>] (__driver_attach) from [<c0401a74>] (bus_for_each_dev+0x68/0x9c)
[<c0401a74>] (bus_for_each_dev) from [<c0402cf0>] (bus_add_driver+0x1a0/0x218)
[<c0402cf0>] (bus_add_driver) from [<c040406c>] (driver_register+0x78/0xf8)
[<c040406c>] (driver_register) from [<c04f20a0>] (i2c_register_driver+0x34/0x84)
[<c04f20a0>] (i2c_register_driver) from [<c01017d0>] (do_one_initcall+0x40/0x170)
[<c01017d0>] (do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
[<c0a00dbc>] (kernel_init_freeable) from [<c06e07b0>] (kernel_init+0x8/0x114)
[<c06e07b0>] (kernel_init) from [<c0107978>] (ret_from_fork+0x14/0x3c)
Code: e1a04000 f590f000 e3a03001 e34f3fff (e1902f9f)
---[ end trace 0919d3d0bc998262 ]---
--------x------------------x----------------
Fix the kernel warnings and crashes by using regulator_bulk_get()
instead of devm_regulator_bulk_get() and explicitly freeing the supplies
in exit paths.
Tested on Exynos 5250, dual core ARM A15 machine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The order in which resources were freed in wm8994_device_exit() isn't
correct. The regulators are removed before they are disabled.
Fix it by reordering code a bit, which makes it exact opposite of
wm8994_device_init() as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap devicetree binding documentation states that a native-endian
property should be supported as well as big-endian & little-endian,
however syscon in its duplication of the parsing of these properties
omits support for native-endian. Fix this by setting
REGMAP_ENDIAN_NATIVE when a native-endian property is found.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This register is used in the AIF code but is missing from the register
tables.
Signed-off-by: Praveen Kumar Vegivada <praveen.vegivada@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
AXP22x has also some different register map than axp20x, they're also
added here.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig and file naming for the PM8xxx driver is totally
confusing:
- Kconfig options MFD_PM8XXX and MFD_PM8921_CORE, some in-kernel
users depending on or selecting either at random.
- A driver file named pm8921-core.c even if it is indeed
used by the whole PM8xxx family of chips.
- An irqchip named pm8xxx since it was (I guess) realized that
the driver was generic for all pm8xxx PMICs.
As I may want to add support for PM8901 this is starting to get
really messy. Fix this situation by:
- Remove the MFD_PM8921_CORE symbol and rely solely on MFD_PM8XXX
and convert all users, including LEDs Kconfig and ARM defconfigs
for qcom and multi_v7 to use that single symbol.
- Renaming the driver to qcom-pm8xxx.c to fit along the two
other qcom* prefixed drivers.
- Rename functions withing the driver from 8921 to 8xxx to
indicate it is generic.
- Just drop the =m config from the pxa_defconfig, I have no clue
why it is even there, it is not a Qualcomm platform. (Possibly
older Kconfig noise from saveconfig.)
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As part of an effort to rid the mostly unused second parameter for I2C
related .probe() functions and to conform to other existing frameworks
we're moving over to a temporary replacement .probe() call-back.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().
Fixes: a9bbba9963 ("mfd: add platform_device sharing support for mfd")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit c4dd1ba355
("mfd: stmpe: Add reset support for all STMPE variant")
we're resetting the STMPE expanders before use.
This caused a regression on the STMP2401 on the Nomadik
NHK8815:
stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x43 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x44 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
It turns out that we start to poll for the reset bit to
go low again too quickly: the STMPE2401 is not yet online and
ready to be asked for the status of the RESET bit.
By introducing a 10ms delay before starting to hammer
the register for information, we get back to normal:
stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101
Cc: stable@vger.kernel.org
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Fixes: c4dd1ba355 ("mfd: stmpe: Add reset support for all STMPE variant")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The wcove USB Type-C driver is currently being flooded with
interrupts that are not targeted to it. The reason for that
is because all CHRG first level interrupts are mapped to it.
This fixes the issue by introducing separate irq for the
usbc device, and mapping only USB Type-C PHY interrupts to
it.
Fixes: 9c6235c863 ("mfd: intel_soc_pmic_bxtwc: Add bxt_wcove_usbc device")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 41a3da2b8e ("mfd: intel-lpss: Save register context on
suspend") saved the register context while going to suspend and
also put the device in reset state.
Due to the resetting of device, system cannot enter S3/S0ix
states when no_console_suspend flag is enabled. The system
and serial console both hang. The resetting of device is not
needed while going to suspend. Hence remove this code.
Cc: stable@vger.kernel.org
Fixes: 41a3da2b8e ("mfd: intel-lpss: Save register context on suspend")
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are a few issues on Intel Kaby Lake PCH-H properties added by
commit a6a576b78e09 ("mfd: lpss: Add Intel Kaby Lake PCH-H PCI IDs"):
- Input clock of I2C controller on Intel Kaby Lake PCH-H is 120 MHz not
133 MHz. This was probably copy-paste error from Intel Broxton I2C
properties.
- There is no default I2C SDA hold time specified which is used when
ACPI doesn't provide it. I got information from Windows driver team
that Kaby Lake PCH-H can use the same configuration than Intel
Sunrisepoint PCH.
- Common HS-UART properties are not used.
Fix these by reusing the Sunrisepoint properties on Kaby Lake PCH-H.
Fixes: a6a576b78e09 ("mfd: lpss: Add Intel Kaby Lake PCH-H PCI IDs")
Reported-by: Xiang A Wang <xiang.a.wang@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
store the physical address of the device in its priv to use it
for DMA addressing in the client drivers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mfd_add_devices enables parsing device tree nodes without compatibles
for regulators and gpio modules. Replace of_platform_populate with
mfd_add_devices. mfd_cell currently is populated with regulators,
gpio and powerbutton.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently read directly calls the repmap read function. Hence
remove the redundant wrapper and use regmap read wherever
needed.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----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=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
This is an extremely quiet release for the regulator API, we've got a
small set of bug fixes and minor feature enhancements for drivers plus a
couple of more visible changes:
- Add support for ramp times in regulators that don't use selectors.
- New driver for LTC3676.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJX83uoExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9AI
Vgf/TKsgLY/UGdEhgmuSCWDI+64e8NjHRADRYR3rpgg8gfa5LeB6M+Zha6FnEWxn
FAj93OAcszNZqHz8ZLZcyV2j9rXhhRlPI1FadAe+0FTQgqN0EKREsL4MHgJNz8C5
mHe/87t8u+4xvscK7JjyvmmMk2UlvvmH8mmaAHTSa3QiX/Jc2isok6NFI370hDRq
DlmgqKU9plZU7hqtvseNFcgiQ1iaFXI6B0Fv6O87czzVvokHdt5BKugKq4LhwInH
A2H6MXap0H2f8GSmFBtXCSonnTKOKYkAUnbEC1LUASCTxPAIEMVMTdO3jV05wI8g
vsy/95OrfLvzKgrE/UlQlV1WZg==
=bca4
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This is an extremely quiet release for the regulator API, we've got a
small set of bug fixes and minor feature enhancements for drivers plus
a couple of more visible changes:
- add support for ramp times in regulators that don't use selectors.
- new driver for LTC3676"
* tag 'regulator-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: dbx500: remove unused functions in dbx500-prcmu.c
regulator: pv88080: Update regulator for PV88080 BB silicon support
regulator: core: don't return error with inadequate reason
regulator: tps65910: Work around silicon erratum SWCZ010
regulator: core: Add set_voltage_time op
regulator: core: Don't skip set_voltage_time when ramp delay disabled
regulator: core: Simplify error flow in _regulator_do_set_voltage()
regulator: core: Use local ops variable in _regulator_do_set_voltage()
regulator: hi6421: mark hi6421_regulator_ldo_get_optimum_mode() static
regulator: Kconfig: Fix typo
regulator: bindings: Use the correct symbol for second
regulator: Remove support for optional supplies in the bulk API
regulator: Add LTC3676 support
regulator: rk808: Delete owner assignment
regulator: tps65218: do not disable DCDC3 during poweroff on broken PMICs
mfd: tps65218: add version check to the PMIC probe
The Arizona CODECs will generally function correctly without a reset line
although it is strongly advised to have one, as such we do allow the system
to boot if the reset gpio is missing or incorrectly specified. However
we should fail probe if we get a probe deferral request, this patch adds
handling for this case.
Reported-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This function is only used in a single place and no new users will be
added as all the devices other required GPIOs are already handled. As
such just merge the code back into the calling function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
This patch adds DT settings for the max_channels_clocked, spk_fmt and
spk_mute pdata.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The McPDM in OMAP4/5 is using the pdmclk from twl6040 as functional clock.
The twl6040-pdmclk driver provides a clock which can be used to make sure
that the pdmclk is active when the McPDM is in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hans de Goede