Add the logic required to enable the compression service for 4xxx devices.
This allows to load the compression firmware image and report
the appropriate compression capabilities.
The firmware image selection for a given device is based on the
'ServicesEnabled' key stored in the internal configuration, which is
added statically at the probe of the device according to the following
rule, by default:
- odd numbered devices assigned to compression services
- even numbered devices assigned to crypto services
In addition, restore the 'ServicesEnabled' key, if present, when SRIOV
is enabled on the device.
Signed-off-by: Tomasz Kowalik <tomaszx.kowalik@intel.com>
Co-developed-by: Mateuszx Potrola <mateuszx.potrola@intel.com>
Signed-off-by: Mateuszx Potrola <mateuszx.potrola@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for triggering a HW reset of a specific ring pair.
Being a device specific feature, add it to the hw_device_data struct.
This feature is supported only by QAT GEN4 devices.
This patch is based on earlier work done by Zelin Deng.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After reset or boot, QAT 4xxx devices are inactive and require to be
explicitly activated.
This is done by writing the DRV_ACTIVE bit in the PM_INTERRUPT register
and polling the PM_INIT_STATE to make sure that the transaction has
completed properly.
If this is not done, the driver will fail the initialization sequence
reporting the following message:
[ 22.081193] 4xxx 0000:f7:00.0: enabling device (0140 -> 0142)
[ 22.720285] QAT: AE0 is inactive!!
[ 22.720287] QAT: failed to get device out of reset
[ 22.720288] 4xxx 0000:f7:00.0: qat_hal_clr_reset error
[ 22.720290] 4xxx 0000:f7:00.0: Failed to init the AEs
[ 22.720290] 4xxx 0000:f7:00.0: Failed to initialise Acceleration Engine
[ 22.720789] 4xxx 0000:f7:00.0: Resetting device qat_dev0
[ 22.825099] 4xxx: probe of 0000:f7:00.0 failed with error -14
The patch also temporarily disables the power management source of
interrupt, to avoid possible spurious interrupts as the power management
feature is not fully supported.
The device init function has been added to adf_dev_init(), and not in the
probe of 4xxx to make sure that the device is re-enabled in case of
reset.
Note that the error code reported by hw_data->init_device() in
adf_dev_init() has been shadowed for consistency with the other calls
in the same function.
Fixes: 8c8268166e ("crypto: qat - add qat_4xxx driver")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add logic to detect device capabilities in qat_4xxx driver.
Read fuses and build the device capabilities mask. This will enable
services and handling specific to QAT 4xxx devices.
Co-developed-by: Tomaszx Kowalik <tomaszx.kowalik@intel.com>
Signed-off-by: Tomaszx Kowalik <tomaszx.kowalik@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for QAT 4xxx devices.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tomasz Kowalik