commit ddab91f4b2de5c5b46e312a90107d9353087d8ea upstream.
In the cases where the power domain connected to logics is allowed to
transition from a level(L)-->power collapse(0)-->retention(1) or
vice versa retention(1)-->power collapse(0)-->level(L) will cause the
logic to lose the configurations. The ARC does not support retention
to collapse transition on MxC rails.
The targets from SM8450 onwards the PLL logics of clock controllers are
connected to MxC rails and the recommended configurations are carried
out during the clock controller probes. The MxC transition as mentioned
above should be skipped to ensure the PLL settings are intact across
clock controller power on & off.
On older targets that do not split MX into MxA and MxC does not collapse
the logic and it is parked always at RETENTION, thus this issue is never
observed on those targets.
Cc: stable@vger.kernel.org # v5.17
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240625-avoid_mxc_retention-v2-1-af9c2f549a5f@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 670c900f69645db394efb38934b3344d8804171a upstream.
When the dts file has multiple referrers to a single PD (e.g.
simple-framebuffer and dss nodes both point to the DSS power-domain) the
ti-sci driver will create two power domains, both with the same ID, and
that will cause problems as one of the power domains will hide the other
one.
Fix this checking if a PD with the ID has already been created, and only
create a PD for new IDs.
Fixes: efa5c01cd7 ("soc: ti: ti_sci_pm_domains: switch to use multiple genpds instead of one")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240415-ti-sci-pd-v1-1-a0e56b8ad897@ideasonboard.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 697624ee8ad557ab5417f985d2c804241a7ad30d ]
According to i.MX8MP RM and HDMI ADD, the fdcc clock is part of
hdmi rx verification IP that should not enable for HDMI TX.
But actually if the clock is disabled before HDMI/LCDIF probe,
LCDIF will not get pixel clock from HDMI PHY and print the error
logs:
[CRTC:39:crtc-2] vblank wait timed out
WARNING: CPU: 2 PID: 9 at drivers/gpu/drm/drm_atomic_helper.c:1634 drm_atomic_helper_wait_for_vblanks.part.0+0x23c/0x260
Add fdcc clock to LCDIF and HDMI TX power domains to fix the issue.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Link: https://lore.kernel.org/r/20240203165307.7806-5-aford173@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d7f58ee08434a33340f75ac7ac5071eea9673b3 ]
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Link: https://lore.kernel.org/r/20240118054257.200814-1-chentao@kylinos.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 883957bee580b723fd87d49ac73e0c84fc03a446 ]
On SA8295P and SA8540P gfx.lvl is not provdied by rpmh, but rather is
handled by an external regulator (max20411). Drop gfx.lvl from the list
of power-domains exposed on this platform.
Fixes: f68f1cb343 ("soc: qcom: rpmhpd: add sc8280xp & sa8540p rpmh power-domains")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240125-sa8295p-gpu-v4-4-7011c2a63037@quicinc.com
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2a93c6cbd5a703d44c414a3c3945a87ce11430ba upstream.
Commit 'e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable
the domain")' aimed to make sure that a power-domain that is being
enabled without any particular performance-state requested will at least
turn the rail on, to avoid filling DeviceTree with otherwise unnecessary
required-opps properties.
But in the event that aggregation happens on a disabled power-domain, with
an enabled peer without performance-state, both the local and peer
corner are 0. The peer's enabled_corner is not considered, with the
result that the underlying (shared) resource is disabled.
One case where this can be observed is when the display stack keeps mmcx
enabled (but without a particular performance-state vote) in order to
access registers and sync_state happens in the rpmhpd driver. As mmcx_ao
is flushed the state of the peer (mmcx) is not considered and mmcx_ao
ends up turning off "mmcx.lvl" underneath mmcx. This has been observed
several times, but has been painted over in DeviceTree by adding an
explicit vote for the lowest non-disabled performance-state.
Fixes: e3e56c050a ("soc: qcom: rpmhpd: Make power_on actually enable the domain")
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/linux-arm-msm/ZdMwZa98L23mu3u6@hovoldconsulting.com/
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240226-rpmhpd-enable-corner-fix-v1-1-68c004cec48c@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0e4a1356466ec1858ae8e5c70bea2ce5e55008b upstream.
The power domain containing the Cortex-R7 CPU core on the R-Car V3H SoC
must always be in power-on state, unlike on other SoCs in the R-Car Gen3
family. See Table 9.4 "Power domains" in the R-Car Series, 3rd
Generation Hardware User’s Manual Rev.1.00 and later.
Fix this by marking the domain as a CPU domain without control
registers, so the driver will not touch it.
Fixes: 41d6d8bd8a ("soc: renesas: rcar-sysc: add R8A77980 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/fdad9a86132d53ecddf72b734dac406915c4edc0.1705076735.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c41336f4d69057cbf88fed47951379b384540df5 upstream.
If the power domains are registered first with genpd and *after that*
the driver attempts to power them on in the probe sequence, then it is
possible that a race condition occurs if genpd tries to power them on
in the same time.
The same is valid for powering them off before unregistering them
from genpd.
Attempt to fix race conditions by first removing the domains from genpd
and *after that* powering down domains.
Also first power up the domains and *after that* register them
to genpd.
Fixes: 59b644b01c ("soc: mediatek: Add MediaTek SCPSYS power domains")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231225133615.78993-1-eugen.hristev@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 374de39d38f97b0e58cfee88da590b2d056ccf7f upstream.
Currently, The imx pgc power domain doesn't set the fwnode
pointer, which results in supply regulator device can't get
consumer imx pgc power domain device from fwnode when creating
a link.
This causes the driver core to instead try to create a link
between the parent gpc device of imx pgc power domain device and
supply regulator device. However, at this point, the gpc device
has already been bound, and the link creation will fail. So adding
the fwnode pointer to the imx pgc power domain device will fix
this issue.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Tested-by: Emil Kronborg <emil.kronborg@protonmail.com>
Fixes: 3fb16866b5 ("driver core: fw_devlink: Make cycle detection more robust")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020185949.537083-1-pengfei.li_1@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b131329b9bfbd1b4c0c5e088cb0c6ec03a12930f upstream.
Without this change, the NPU hangs when the 8th NN core is used.
It matches what the out-of-tree driver does.
Signed-off-by: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Fixes: 9a217b7e89 ("soc: amlogic: meson-pwrc: Add NNA power domain for A311D")
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231016080205.41982-2-tomeu@tomeuvizoso.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e75396f1df61e1f1d26d0d703fc7292c4ae4371 upstream.
The commit c494a447c1 ("soc: bcm: bcm2835-power: Refactor ASB control")
refactored the ASB control by using a general function to handle both
the enable and disable. But this patch introduced a subtle regression:
we need to check if !!(readl(base + reg) & ASB_ACK) == enable, not just
check if (readl(base + reg) & ASB_ACK) == true.
Currently, this is causing an invalid register state in V3D when
unloading and loading the driver, because `bcm2835_asb_disable()` will
return -ETIMEDOUT and `bcm2835_asb_power_off()` will fail to disable the
ASB slave for V3D.
Fixes: c494a447c1 ("soc: bcm: bcm2835-power: Refactor ASB control")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231024101251.6357-2-mcanal@igalia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per "dt-bindings/firmware/imx/rsrc.h", `IMX_SC_R_DMA_2_CH0 + 5` not
equals to IMX_SC_R_DMA_2_CH5, so there should be two entries in
imx8qxp_scu_pd_ranges, otherwise the imx_scu_add_pm_domain may filter
out wrong power domains.
Fixes: 927b7d15dc ("genpd: imx: scu-pd: enlarge PD range")
Reported-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20231001123853.200773-1-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has been pointed out that naming a subsystem "genpd" isn't very
self-explanatory and the acronym itself that means Generic PM Domain, is
known only by a limited group of people.
In a way to improve the situation, let's rename the subsystem to pmdomain,
which ideally should indicate that this is about so called Power Domains or
"PM domains" as we often also use within the Linux Kernel terminology.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230912221127.487327-1-ulf.hansson@linaro.org
Taniya Das