DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the separate paths for frames coming from the outside, and
frames sent from the HSR device, and instead makes all frames go through
hsr_forward_skb() in hsr_forward.c. This greatly improves code readability and
also opens up the possibility for future support of the HSR Interlink device
that is the basis for HSR RedBoxes and HSR QuadBoxes, as well as VLAN
compatibility.
Other improvements:
* A reduction in the number of times an skb is copied on machines without
HAVE_EFFICIENT_UNALIGNED_ACCESS, which improves throughput somewhat.
* Headers are now created using the standard eth_header(), and using the
standard hard_header_len.
* Each HSR slave now gets its own private skb, so slave-specific fields can be
correctly set.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also try to prevent some possible slave dereference race conditions. This is
finalized in the next patch, which abandons the slave array in favour of
a list_head list and list RCU.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also move the frame receive handler to hsr_slave.c.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Murali Karicheri