Fixes a crash on attempting to calculate the frame duration for a VHT
packet (which needs to be handled by hw/driver instead).
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate mask code currently assumes that a rate is legacy if
IEEE80211_TX_RC_MCS is not set. This might be the cause of bogus VHT
rates being reported with minstrel_ht.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It affects non-(V)HT rates and can lead to selecting an rts_cts rate
that is not a basic rate or way superior to the reference rate (ATM
rates[0] used for the 1st attempt of the protected frame data).
E.g, assuming drivers register growing (bitrate) sorted tables of
ieee80211_rate-s, having :
- rates[0].idx == d'2 and basic_rates == b'10100
will select rts_cts idx b'10011 & ~d'(BIT(2)-1), i.e. 1, likewise
- rates[0].idx == d'2 and basic_rates == b'10001
will select rts_cts idx b'10000
The first is not a basic rate and the second is > rates[0].
Also, wrt severity of the addressed misbehavior, ATM we only have one
rts_cts_rate_idx rather than one per rate table entry, so this idx might
still point to bitrates > rates[1..MAX_RATES].
Fixes: 5253ffb8c9 ("mac80211: always pick a basic rate to tx RTS/CTS for pre-HT rates")
Cc: stable@vger.kernel.org
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's not a single rate control algorithm actually in
a separate module where the module refcount would be
required. Similarly, there's no specific rate control
module.
Therefore, all the module handling code in rate control
is really just dead code, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bitrate mask were not respected in transmissions, causing (for
example) P2P GO/client to use CCK rates for auth and assoc frames.
Fix it by considering the rate mask in __rate_control_send_low().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Transmissions with the IEEE80211_TX_CTL_NO_CCK_RATE flag set
(which can come from userspace) were no longer guaranteed to
be transmitted with allowed rates since commit 2103dec147
("mac80211: select and adjust bitrates according to channel
mode") due to a missing rate_flags check in that commit. The
commit also introduced the need to check the 5/10 MHz flags
but accidentally didn't. Fix it by adding the missing check.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow lowest basic rate to be used for unicast management frame in
mesh. Otherwise, the lowest supported rate is used for unicast
management frame, such as 1Mbps for 2.4GHz and 6Mbps for 5GHz. Rename
the rc_send_low_broadcast to re_send_low_basicrate since now it is
also applied to unicast management frame in mesh.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a collection of minor fixes:
* don't allow HT IEs in IBSS for 5/10 MHz
* don't allow HT IEs in Mesh for 5/10 MHz
* don't downgrade from/to 5 and 10 MHz channels
* don't try HT rates for 5 and 10 MHz channels when selecting rates
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The order of parameters was mixed up, introduced in commit
"mac80211: improve the rate control API"
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Document rx vs tx status concurrency requirements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow rate control modules to pass a rate selection table to mac80211
and the driver. This allows drivers to fetch the most recent rate
selection from the sta pointer for already buffered frames. This allows
rate control to respond faster to sudden link changes and it is also a
step towards adding minstrel_ht support to drivers like iwlwifi.
When a driver sets IEEE80211_HW_SUPPORTS_RC_TABLE, mac80211 will not
fill info->control.rates with rates from the rate table (to preserve
explicit overrides by the rate control module). The driver then
explicitly calls ieee80211_get_tx_rates to merge overrides from
info->control.rates with defaults from the sta rate table.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the code always copies the configured MCS mask (even if it is
set to default), but only uses it if legacy rates were also masked out.
Fix this by adding a flag that tracks whether the configured MCS mask is
set to default or not.
Optimize the code further by storing a pointer to the configured rate
mask in txrc instead of using memcpy.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
rate control algorithms concludes the rate as invalid
with rate[i].idx < -1 , while they do also check for rate[i].count is
non-zero. it would be safer to zero initialize the 'count' field.
recently we had a ath9k rate control crash where the ath9k rate control
in ath_tx_status assumed to check only for rate[i].count being non-zero
in one instance and ended up in using invalid rate index for
'connection monitoring NULL func frames' which eventually lead to the crash.
thanks to Pavel Roskin for fixing it and finding the root cause.
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Cc: stable@vger.kernel.org
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ridx" is used as an index into the mcs_mask[] array which has
IEEE80211_HT_MCS_MASK_LEN elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems exceedingly unlikely that we'll ever
support swapping rate control algorithms at
runtime, so remove the unused refcounting code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With calls to modular infrastructure, these files really
needs the full module.h header. Call it out so some of the
cleanups of implicit and unrequired includes elsewhere can be
cleaned up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Recently mac80211 was changed to use nullfunc instead of probe
request for connection monitoring for tx ack status reporting
hardwares. Sometimes in congested network, STA got disconnected
quickly after the association. It was observered that the rate
control was not adopted to environment due to minimal transmission.
As the nullfunc are used for monitoring purpose, these frames should
not be sacrificed for rate control updation. So it is better to send
the monitoring null func frames at minimum rate that could help to
retain the connection.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I found this bug while poking around with a pure-gn AP.
Commit:
cfg80211/mac80211: Use more generic bitrate mask for rate control
Added some sanity checks to ensure that each tx rate index
is included in the configured mask and it would change any
rate indexes if it wasn't.
But, the current implementation doesn't take into account
that the invalid rate index "-1" has a special meaning
(= no further attempts) and it should not be "changed".
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the writing to sysfs can free the old one, we need to block that
when we access the charp variables.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Jing Huang <huangj@brocade.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
For hardware with IEEE80211_HW_HAS_RATE_CONTROL the rate controller is not
initialized. However, calling functions such as ieee80211_beacon_get result
in the rate_control_get_rate function getting called, which is accessing
(in this case uninitialized) rate control structures unconditionally.
Fix by exiting the function before setting the rates for HW with
IEEE80211_HW_HAS_RATE_CONTROL set. The initialization of the ieee80211_tx_info
struct is intentionally still executed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rate_control_alloc is not used by anything outside of
ieee80211_init_rate_ctrl_alg. Both are in rate.c; there's no reason to make
rate_control_alloc visible outside of it.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend struct cfg80211_bitrate_mask to actually use a bitfield mask
instead of just a single fixed or maximum rate index. This change
itself does not modify the behavior (except for debugfs files), but it
prepares cfg80211 and mac80211 for a new nl80211 command for setting
which rates can be used in TX rate control.
Since frames are now going through the rate control algorithm
unconditionally, the internal IEEE80211_TX_INTFL_RCALGO flag can now
be removed. The RC implementations can use the rate_idx_mask value to
optimize their behavior if only a single rate is enabled.
The old max_rate_idx in struct ieee80211_tx_rate_control is maintained
(but commented as deprecated) for backwards compatibility with existing
RC implementations. Once these implementations have been updated to
use the more generic rate_idx_mask, the max_rate_idx value can be
removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the basic rate set is configured to not include the lowest rate
(e.g., basic rate set = 6, 12, 24 Mbps in IEEE 802.11g mode), the AP
should not send out broadcast frames at 1 Mbps. This type of
configuration can be used to optimize channel usage in cases where
there is no need for backwards compatibility with IEEE 802.11b-only
devices.
In AP mode, mac80211 was unconditionally using the lowest rate for
Beacon frames and similarly, with all rate control algorithms that use
rate_control_send_low(), the lowest rate ended up being used for all
broadcast frames (and all unicast frames that are sent before
association). Change this to take into account the basic rate
configuration in AP mode, i.e., use the lowest rate in the basic rate
set instead of the lowest supported rate when selecting the rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices implement the entire rate control in
firmware in some way, like wl1271 or like iwlwifi
which does some things in software but not a lot.
Therefore generic software rate control is rather
useless for them and just adds avoidable overhead
to the transmit path.
It's fairly simple to let drivers indicate that
they do not need rate control, but they need to
fulfil a number of conditions that we encode in
WARN_ONs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can save a lot of code and pointers in the structs
by using debugfs_remove_recursive().
First, change cfg80211 to use debugfs_remove_recursive()
so that drivers do not need to clean up any files they
added to the per-wiphy debugfs (if and only if they are
ok to be accessed until after wiphy_unregister!).
Then also make mac80211 use debugfs_remove_recursive()
where necessary -- it need not remove per-wiphy files
as cfg80211 now removes those, but netdev etc. files
still need to be handled but can now be removed without
needing struct dentry pointers to all of them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All current rate control algorithms agree to send management and no-ack
frames at the lowest rate. They also agree to do this when sta
and the private rate control data is NULL. We add a hlper to mac80211
for this and simplify the rate control algorithm code.
Developers wishing to make enhancements to rate control algorithms
are for broadcast/multicast can opt to not use this in their
gate_rate() mac80211 callback.
Cc: Zhu Yi <yi.zhu@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: ipw3945-devel@lists.sourceforge.net
Cc: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to not notify the rate control algorithm's
tx_status() method when reporting status for a packet that didn't go
through the rate control algorithm's get_rate() method.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Long awaited, hard work. This patch totally cleans up the rate control
API to remove the requirement to include internal headers outside of
net/mac80211/.
There's one internal use in the PID algorithm left for mesh networking,
we'll have to figure out a way to clean that one up and decide how to
do the peer link evaluation, possibly independent of the rate control
algorithm or via new API.
Additionally, ath9k is left using the cross-inclusion hack for now, we
will add new API where necessary to make this work properly, but right
now I'm not expert enough to do it. It's still off better than before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau