Have separate netdev_ops for OSA and HiperSocket/TR.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DEBUG_FS is disabled debugfs_create_file returns -ENODEV instead
of zero. Since the return value is stored and used at shutdown to remove
existing entries an OOPS may be triggered.
Add a check of the debugfs_create_file return value and in case of an error
set the entry to NULL so it will be ignored at shutdown.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the connection between host and storage server is lost, the
dasd device driver usually blocks all I/O on affected devices and
waits for them to reappear. In some setups however it would be
better if the I/O is returned as error so that device can be
recovered by some other means, eg. in a raid or multipath setup.
Signed-off-by: Holger Smolinski <Holger.Smolinski@de.ibm.com>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a DASD device enters or leaves the 'online' state we need to
trigger change events for the respective disk and partitions.
These extra events are needed because when disk and partitions are
first added, udev rules that try to read disk labels or other data
may fail as the disk may not yet be ready.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC drivers/s390/char/tape_block.o
In file included from drivers/s390/char/tape_block.c:24:
drivers/s390/char/tape.h:159: warning: 'struct request' declared inside
parameter list
Adding the dependency of CONFIG_BLOCK to CONFIG_S390_TAPE_BLOCK.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (84 commits)
wimax: fix kernel-doc for debufs_dentry member of struct wimax_dev
net: convert pegasus driver to net_device_ops
bnx2x: Prevent eeprom set when driver is down
net: switch kaweth driver to netdevops
pcnet32: round off carrier watch timer
i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
wimax: testing for rfkill support should also test for CONFIG_RFKILL_MODULE
wimax: fix kconfig interactions with rfkill and input layers
wimax: fix '#ifndef CONFIG_BUG' layout to avoid warning
r6040: bump release number to 0.20
r6040: warn about MAC address being unset
r6040: check PHY status when bringing interface up
r6040: make printks consistent with DRV_NAME
gianfar: Fixup use of BUS_ID_SIZE
mlx4_en: Returning real Max in get_ringparam
mlx4_en: Consider inline packets on completion
netdev: bfin_mac: enable bfin_mac net dev driver for BF51x
qeth: convert to net_device_ops
vlan: add neigh_setup
dm9601: warn on invalid mac address
...
qeth_l2, qeth_l3 convert to net_device_ops.
qeth_l3 remove vlan neigh_setup hack since it does not work any longer
with the new net_device_ops.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (44 commits)
qlge: Fix sparse warnings for tx ring indexes.
qlge: Fix sparse warning regarding rx buffer queues.
qlge: Fix sparse endian warning in ql_hw_csum_setup().
qlge: Fix sparse endian warning for inbound packet control block flags.
qlge: Fix sparse warnings for byte swapping in qlge_ethool.c
myri10ge: print MAC and serial number on probe failure
pkt_sched: cls_u32: Fix locking in u32_change()
iucv: fix cpu hotplug
af_iucv: Free iucv path/socket in path_pending callback
af_iucv: avoid left over IUCV connections from failing connects
af_iucv: New error return codes for connect()
net/ehea: bitops work on unsigned longs
Revert "net: Fix for initial link state in 2.6.28"
tcp: Kill extraneous SPLICE_F_NONBLOCK checks.
tcp: don't mask EOF and socket errors on nonblocking splice receive
dccp: Integrate the TFRC library with DCCP
dccp: Clean up ccid.c after integration of CCID plugins
dccp: Lockless integration of CCID congestion-control plugins
qeth: get rid of extra argument after printk to dev_* conversion
qeth: No large send using EDDP for HiperSockets.
...
drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_setadapter_parms':
drivers/s390/net/qeth_l3_main.c:1049: warning: too many arguments for format
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
The device driver qeth dos not support large send using EDDP for
HiperSockets.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip assist hw command for setting an IP address last unacceptable
long so we can not spin while we waiting for the irq. Since we can
ensure process context for all occurrences of this command we can use
wait.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For z/VM GuestLAN or VSWITCH devices the transport layer is
configured in z/VM. The layer2 attribute of a participating Linux
device has to match the z/VM definition. In case of a mismatch
Linux currently crashes in qeth recovery due to a reference to the
not yet existing net_device.
Solution: add a check for existence of net_device and add a message
pointing to the mismatch of layer definitions in Linux and z/VM.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSA-devices operating in layer3 mode offer adding of the source MAC
address to the QDIO header of inbound packets. The qeth driver can
exploit this functionality to replace FAKELL-entries in the ethernet
header of received packets.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pre z9 machines provide an mcl string in EBCDIC format,
z9 or later provide string in ASCII format.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish the cputime of the idle process where idle is actually using
cpu cycles from the cputime where idle is sleeping on an enabled wait psw.
The former is accounted as system time, the later as idle time.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements config_changed for the s390 virtio transport.
We use the least significant bit of the interrupt parameter field
to decide, if this interrupt should call the virtio virtqueue callback
or the config_changed callback.
This method is compatible with old host and guest code. Old 64 bit guests
will not check the bit and trigger a harmless additional vring_interrupt
call. Old host code will never set this bit, this is also safe.
This patch also takes care of a potential future 31 bit virtio transport
for s390. On 31 bit _LC_PFAULT_INTPARM and __LC_EXT_PARAMS are identical.
We exploit the alignment of the token and fold the change bit into the
lsb of the token itself.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This allows each virtio user to hand in the alignment appropriate to
their virtio_ring structures.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
This doesn't really matter, since s390 pagesize is 4k anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Remove a message that was emitted for a port that could not initially
be opened. This is a rare case when the port discovery hits an
initiator port and only confuses the user with an initator port logged
in the message. Remove the whole special case: The failed "open port"
request triggers required follow-up actions anyway.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add the support to send CT and ELS requests as unchained FSF requests. This is
required for older hardware and was somehow omitted during the cleanup of the
FSF layer. The req_count and resp_count attributes are unused, so remove them
instead of adding a special case for setting them. Also add debug data and a
warning, when the ct request hits a limit.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With the change to the dev_ message macros, the macro to get the busid
is only used in a few places. Remove it and directly get the dev_name
from the device.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The port flag DID_DID indicates whether we know the current id of the
port. This is always set in parallel. Since the id 0 is invalid
(because the port id 0 is invalid) we can remove the DID_DID flag:
d_id of 0 indicates an invalid d_id != 0 is a valid one.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use an array for looking up the mask corresponding to the 2-bit
information instead of the switch/case.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The information from the kernel parameter is only needed during init.
Keep the three pieces (busid, wwpn and lun) local to simplify the
global zfcp_data structures. While at it, also remove the unused
loglevel variable and give the module parameter variable a better
name.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Get rid of this one:
drivers/s390/scsi/zfcp_erp.c: In function 'zfcp_erp_thread':
drivers/s390/scsi/zfcp_erp.c:1400: warning: ignoring return value of
'down_interruptible', declared with attribute warn_unused_result
zfcp_erp_thread is a kernel thread which can't receive any signals.
So introduce a dummy variable and get rid of the warning.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After the latest changes, the list of FCP devices is only used to
lookup the adapter for requests from the actcli tool. Change this to
use the lookup function in the cio layer. Now we can remove the
adapter list and have one place less to use the global config_lock.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When waiting for a request claim the SBAL before waiting. This way,
locking before each check of the free counter is not required and
sparse does not emit warnings for the complicated locking scheme.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Synchronize the registration and de-registration with the SCSI layer
at CCW registration, de-registration. Before we registered with the
SCSI layer on adapter activation. This way the reg and de-reg process
is in balance.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Move the closing parenthesis before the line break.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
The loop above the modified code only terminates when rc is a valid pointer.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x@p1 == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)
// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@
... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)
@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@
(
- if ((x@p2 != NULL) || ...)
S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If reply is ERR_PTR(...), then it should not be dereferenced, so I have
moved the dereference from the declaration to after the IS_ERR test.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@match exists@
expression x, E;
identifier fld;
position p1,p2;
@@
(
x = E;
|
x = E
|
x@p1->fld
... when != x = E
IS_ERR(x@p2)
... when any
)
@other_match exists@
expression match.x, E1, E2;
position match.p1,match.p2;
@@
x = E1
... when != x = E2
when != x@p1
x@p2
@ script:python depends on !other_match@
p1 << match.p1;
p2 << match.p2;
@@
print "* file %s dereference %s test %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
get rid of this one:
CC drivers/s390/char/sclp_vt220.o
drivers/s390/char/sclp_vt220.c:588: warning: '__sclp_vt220_flush_buffer' defined but not used
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To check if multipath is available we count the bits set in lpm,
which could change over time (via configure [on|off] of a path).
The following patch uses the pim (which is persistent) for this
decision.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Sometimes we change the pmcw configuration but don't call msch
to transmit these changes to the channel subsystem.
The patch fixes this by calling cio_commit_config in such cases.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To change the configuration of a subchannel we alter the modifiable
bits of the subchannel's schib field and issue a modify subchannel.
There can be the case that not all changes were applied -or worse-
quietly overwritten by the hardware. With the next store subchannel
we obtain the current state of the hardware but lose our target
configuration.
With this patch we introduce a subchannel_config structure which
contains the target subchannel configuration. Additionally the msch
wrapper cio_modify is replaced with cio_commit_config which
copies the desired changes to a temporary schib. msch is then
called with the temporary schib. This schib is only written back
to the subchannel if all changes were applied.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is the chance that we get condition code 0 for a stsch but
the resulting schib is not vaild. In the current code there are
2 cases:
* we do a check for validity of the schib after stsch, but at this
time we have already stored the invaild schib in the subchannel
structure. This may lead to problems.
* we don't do a check for validity, which is not that good either.
The patch addresses both issues by introducing the stsch wrapper
cio_update_schib which performs stsch on a local schib. This schib
is only written back to the subchannel if it's valid.
side note: For some functions (chp_events) the return codes are
different now (-ENXIO vs -ENODEV) but this shouldn't do harm
since the caller doesn't check for _specific_ errors.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check if a ccw device is registered via device_is_registered()
and not via the old kludge of checking the membership in driver
core internal klists.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just put the cdev's reference count to give up our reference.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we fail the probe for an I/O subchannel, we won't be able
to unregister it again since there are no sch_event()
callbacks for unbound subchannels. Just succeed the probe in
any case and schedule unregistering the subchannel.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a race between io_subchannel_register() and
io_subchannel_sch_event() which may cause a subchannel to be
unregistered because it is no longer operational before
io_subchannel_register() had run. We need to check whether the
subchannel is still registered before the ccw device can be
registered and just bail out if it is not.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Subchannel refcounting was incorrect in some places, especially
a refcount was missing when ccw_device_call_sch_unregister()
was called and the refcount was not correctly switched after
moving devices.
Fix this by establishing the following rules:
- The ccw_device obtains a reference on its parent subchannel
when dev.parent is set and gives it up in its release
function. This is needed because we need a parent reference
for correct refcounting even before the ccw device is (if at
all) registered.
- When calling device_move(), obtain a reference on the new
subchannel before moving the ccw device and give up the
reference on the old parent after moving. This brings the
refcount in line with the first rule.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current code attempts to get an extra reference count
for online devices by doing a get_device() in ccw_device_online()
and a put_device() in ccw_device_done(). However, this
- incorrectly obtains an extra reference for disconnected
devices becoming available again (since they are already
online)
- needs special checks for css_init_done in order to handle
the console device
- is not obvious and
- may incorretly drop a reference count in ccw_device_done() if
that function is called after path verification for a device
that just became not operational.
So let's just get the reference in ccw_device_set_online() and
drop it in ccw_device_set_offline(). (Unfortunately, we still
need the special case in io_subchannel_probe().)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure atomicity of ungroup operation to prevent concurrent ungroup
and online processing which may lead to use-after-release situations.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Due to former patches a comment and device id initialization were
split from the addressed function call in io_subchannel_probe.
Move it back to where it belongs.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move cio_tpi() to the rest of the CONFIG_CCW_CONSOLE functions to
get rid of this one:
drivers/s390/cio/cio.c:115: warning: 'cio_tpi' defined but not used
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__dasd_cleanup_cqr should be called with request_queue_lock held and
__dasd_block_process_erp with queue_lock
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
SIM sense data are always 32 bit sense data so sense byte 27 bit 0
has not to be set.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a large number of I/O requests the values were shifted binary.
The shift was not transparent for the user because the shift value
was not displayed. To make this interface more human readable the
values are shifted decimal and the scale factor is displayed.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Register zfcp with the new /proc/service_level interface to report the
FCP microcode level. When the adapter goes offline or a channel path
disappears, zfcp unregisters, since the microcode version might change
and zfcp does not know about it.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a new proc interface /proc/service_levels that allows any code
to report a relevant service level, e.g. the microcode level of
devices, the service level of the hypervisor, etc.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Hipersocket connections can encounter temporary busy conditions.
In case of the busy bit set we retry the SIGA operation immediatelly.
If the busy condition still persists after 100 ms we fail and report
the error to the upper layer. The second stage retry logic is removed.
In case of ongoing busy conditions the upper layer needs to reset the
connection.
The reporting of a SIGA error is now done synchronously to allow the
network driver to requeue the buffers. Also no error trace is created
for the temporary SIGA errors so the error message view is not flooded.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- Use automatic acknowledgement of incoming buffers in QEBSM mode
- Move ACK for non-QEBSM mode always to the newest buffer to prevent
a race with qdio_stop_polling
- Remove the polling spinlock, the upper layer drivers return new buffers
in the same code path and could not run in parallel
- Don't flood the error log in case of no-target-buffer-empty
- In handle_inbound we check if we would overwrite an ACK'ed buffer, if so
advance the pointer to the oldest ACK'ed buffer so we don't overwrite an
empty buffer in qdio_stop_polling
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- make qdio_trace a per device view
- remove s390dbf exceptions
- remove CONFIG_QDIO_DEBUG, not needed anymore if we check for the level
before calling sprintf
- use snprintf for dbf entries
- add start markers to see if the dbf view wrapped
- add a global error view for all queues
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The QEBSM instructions are only available for CONFIG_64BIT, they are not
used under 31 bit. Make compiler happy about the false positive:
drivers/s390/cio/qdio_main.c: In function ?qdio_inbound_q_done?:
drivers/s390/cio/qdio_main.c:532: warning: ?state? may be used uninitialized in this function
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add counters for the eqbs and sqbs instructions that indicate how often
we issued the instructions and how often the instructions returned with
less buffers than specified.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qeth needs to get the port count information before
qdio has allocated a page for the chsc operation.
Extend qdio_get_ssqd_desc() to store the data in the
specified structure.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changed some symbol names for a better and clearer code.
Signed-off-by: Christian Maaser <cmaaser@de.ibm.com>
Signed-off-by: Felix Beck <beckf@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the machine supports AP adapter interrupts polling will be
switched off at module initialization and the driver will work in
interrupt mode.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vmcp driver uses the session->mutex for concurrent access of the data
structures. Therefore, the BKL in vmcp_open does not protect against any
other function in the driver.
The BLK in vmcp_open would protect concurrent access to the module init
but all necessary steps ave finished before misc_register is called.
We can safely remove the lock_kernel from vcmp.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The private data comes from ccwgroup_device.
So just don't allocate private data memory when do alloc_netdev()
and use netdev->ml_priv to reference private data.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zfcp_scsi_queuecommand was not acting according to the standard
when the respective unit was not available. In this case an -EBUSY was
returned, which is not valid in itself, and in addition scsi_done
was called. This combination is not allowed and was leading to a
double finish of the request and therefor double decrement of the
host_busy counter.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Waiting for the ERP to be finished in a task running in the global
kernel work-queue is a bad idea, especially if the ERP needs to run
another job in this work-queue before it can finish. -> deadlock.
This patch removes the necessity to wait for a finished ERP from the
scan task and moves the job scheduling to the end of the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The check of having a valid pointer was performed before the
processing was secured by the lock. Between those two steps the
pointer can turn invalid. During further processing another value is
used (referenced by the pointer described above) as a function pointer
which is never verified to be valid either, resulting under some
circumstances in an invalid function call. This patch is fixing both
issues.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Prevent a SCSI target scan for a rport which have turned invalid
in the meantime.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Aborting a SCSI cmnd might requrie to send a abort_fsf_cmnd. If the
creation of this fsf_req fails an ERR_PTR is returned where a NULL
value would be expected as an error indicator. This ERR_PTR is
dereferenced as valid fsf_req in succeeding processing leading to
an error.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Running two wka_port_get calls in parallel could issue two open_port
requests, overwriting the port handle. Don't issue an open_port
for the state PORT_OPENING, and only read the data from GOOD
responses.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For an incoming RSCN it was checked by the ZFCP_STATUS_PORT_DID_DID
define to re-open a remote port or to test the connection. Since this
define was re-used it was also necessary to replace that define with
ZFCP_STATUS_PORT_PHYS_OPEN.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The first argument to csum_partial is const void *
casts to char/u8 * are not necessary
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logging of sense data for fatal errors was accidentally removed
during Hyper PAV implementation.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In ccw_device_move_to_orphanage(), a replacing ccw_device
is searched via get_{disc,orphaned}_ccwdev_by_dev_id()
which obtain a reference on the returned ccw_device.
This reference must be given up again after the device
has been moved to its new parent.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current virtio model on s390 has the descriptor page above the main
memory. The guest virtio detection will oops if the mem= parameter is
used to reduce/change the memory size.
We have to use real_memory_size instead of max_pfn to detect the virtio
descriptor pages.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fix multiple problems found in the hexdump data:
- length calculation was wrong, traces were incomplete
- FC payloads were dumped in different record than the output
function tried to read
- minor fixes in output
- allow complete RSCN traces (up to 1024 bytes according to spec)
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If an open port fsf request times out (in erp) the
corresponding erp_action member of the fsf
request need to set to NULL. If the port structure
will be removed later-on there will be still a
reference in the fsf request to the non existing
erp_action otherwise.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Attaching a unit immediately after setting the adapter online should
be possible. The problem right now is that the port_scan runs from a
workqueue and has not finished when the set_online call returns and
the sysfs structures for the ports are not available yet. Fix that by
waiting for the port scan to complete.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix leftover from last typecast patch:
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_port_enqueue’:
drivers/s390/scsi/zfcp_aux.c:629: warning: format ‘%016llx’ expects
type ‘long long unsigned int’, but argument 3 has type ‘u64’
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix the handling of the request list in the error path:
- Use irqsave for the lock as in the good path.
- Before removing the request, check if it is still in the list, a
call to dismiss_all might have changed the list in between.
- zfcp_qdio_send does not change the queue counters on failure,
trying revert something is wrong, so remove this.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When allocating fsf requests without qtcb, store the pointer to the
mempool in the fsf requests for later call to mempool_free. This
codepath is only used by the status_read requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The per adapter req_list_lock must be held with interrupts disabled, otherwise
we might end up with nice deadlocks as lockdep tells us (see below).
zfcp 0.0.1804: QDIO problem occurred.
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
2.6.27-rc8-00035-g4a77035-dirty #86
---------------------------------------------------------
swapper/0 just changed the state of lock:
(&adapter->erp_lock){++..}, at: [<00000000002c82ae>] zfcp_erp_adapter_reopen+0x4e/0x8c
but this lock took another, hard-irq-unsafe lock in the past:
(&adapter->req_list_lock){-+..}
and interrupts could create inverse lock ordering between them.
[tons of backtraces, but only the interesting part follows]
the second lock's dependencies:
-> (&adapter->req_list_lock){-+..} ops: 2280627634176 {
initial-use at:
[<0000000000071f10>] __lock_acquire+0x504/0x18bc
[<000000000007335c>] lock_acquire+0x94/0xbc
[<00000000003d7224>] _spin_lock_irqsave+0x6c/0xb0
[<00000000002cf684>] zfcp_fsf_req_dismiss_all+0x50/0x140
[<00000000002c87ee>] zfcp_erp_adapter_strategy_generic+0x66/0x3d0
[<00000000002c9498>] zfcp_erp_thread+0x88c/0x1318
[<000000000001b0d2>] kernel_thread_starter+0x6/0xc
[<000000000001b0cc>] kernel_thread_starter+0x0/0xc
in-softirq-W at:
[<0000000000072172>] __lock_acquire+0x766/0x18bc
[<000000000007335c>] lock_acquire+0x94/0xbc
[<00000000003d7224>] _spin_lock_irqsave+0x6c/0xb0
[<00000000002ca73e>] zfcp_qdio_int_resp+0xbe/0x2ac
[<000000000027a1d6>] qdio_kick_inbound_handler+0x82/0xa0
[<000000000027daba>] tiqdio_inbound_processing+0x62/0xf8
[<0000000000047ba4>] tasklet_action+0x100/0x1f4
[<0000000000048b5a>] __do_softirq+0xae/0x154
[<0000000000021e4a>] do_softirq+0xea/0xf0
[<00000000000485de>] irq_exit+0xde/0xe8
[<0000000000268c64>] do_IRQ+0x160/0x1fc
[<00000000000261a2>] io_return+0x0/0x8
[<000000000001b8f8>] cpu_idle+0x17c/0x224
hardirq-on-W at:
[<0000000000072190>] __lock_acquire+0x784/0x18bc
[<000000000007335c>] lock_acquire+0x94/0xbc
[<00000000003d702c>] _spin_lock+0x5c/0x9c
[<00000000002caff6>] zfcp_fsf_req_send+0x3e/0x158
[<00000000002ce7fe>] zfcp_fsf_exchange_config_data+0x106/0x124
[<00000000002c8948>] zfcp_erp_adapter_strategy_generic+0x1c0/0x3d0
[<00000000002c98ea>] zfcp_erp_thread+0xcde/0x1318
[<000000000001b0d2>] kernel_thread_starter+0x6/0xc
[<000000000001b0cc>] kernel_thread_starter+0x0/0xc
}
... key at: [<0000000000e356c8>] __key.26629+0x0/0x8
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmit@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It is possible that a remote port has a problem, the SCSI device gets
deleted after the rport timeout and then the timeout for pending SCSI
commands trigger an abort. For this case, don't delete the reference
from the SCSI device to the zfcp unit, so that we can still have the
reference to issue an abort request.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
__blk_end_request must be called with request queue lock held. We need to use
blk_end_request rather than __blk_end_request.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the memset since zeroing the string is not needed and use
snprintf instead of sprintf.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of I/O errors on a qdio subchannel qdio_shutdown may be
called twice by the qdio driver and by zfcp. Remove the
superfluous shutdown from qdio and let the upper layer driver
handle the error condition.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the qeth driver more robust in case of malformatted inbound
packets due to hardware problems, an additional check for
OSN-card-type is added for OSN-type packets.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Removing this check improves usability because you do not have to
set the device online to initially set ipv6 routing option.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For the non preallocated qeth header code path we should not
change the header length.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
IP-threads have been removed from the qeth driver. Only the
recover-thread is left over. This makes checkings for
non-recover threads superfluous.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'v28-range-hrtimers-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
hrtimers: add missing docbook comments to struct hrtimer
hrtimers: simplify hrtimer_peek_ahead_timers()
hrtimers: fix docbook comments
DECLARE_PER_CPU needs linux/percpu.h
hrtimers: fix typo
rangetimers: fix the bug reported by Ingo for real
rangetimer: fix BUG_ON reported by Ingo
rangetimer: fix x86 build failure for the !HRTIMERS case
select: fix alpha OSF wrapper
select: fix alpha OSF wrapper
hrtimer: peek at the timer queue just before going idle
hrtimer: make the futex() system call use the per process slack value
hrtimer: make the nanosleep() syscall use the per process slack
hrtimer: fix signed/unsigned bug in slack estimator
hrtimer: show the timer ranges in /proc/timer_list
hrtimer: incorporate feedback from Peter Zijlstra
hrtimer: add a hrtimer_start_range() function
hrtimer: another build fix
hrtimer: fix build bug found by Ingo
hrtimer: make select() and poll() use the hrtimer range feature
...
* get rid of fake struct file/struct dentry in __blkdev_get()
* merge __blkdev_get() and do_open()
* get rid of flags argument of blkdev_get()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove __generic_unplug_device() from exports
block: move q->unplug_work initialization
blktrace: pass zfcp driver data
blktrace: add support for driver data
block: fix current kernel-doc warnings
block: only call ->request_fn when the queue is not stopped
block: simplify string handling in elv_iosched_store()
block: fix kernel-doc for blk_alloc_devt()
block: fix nr_phys_segments miscalculation bug
block: add partition attribute for partition number
block: add BIG FAT WARNING to CONFIG_DEBUG_BLOCK_EXT_DEVT
softirq: Add support for triggering softirq work on softirqs.
This patch writes the channel and fabric latencies in nanoseconds per
request via blktrace for later analysis. The utilization of the inbound
and outbound adapter queue is also reported.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop the kernel lock further and also correct cases where we set rc to an
error code, and then return 0
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_current_tty now does internal locking and returns a referenced object,
thus our use of tty_mutex here can go away.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently it is sometimes locked by the tty mutex and sometimes by the
sighand lock. The latter is in fact correct and now we can hand back referenced
objects we can fix this up without problems around sleeping functions.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now return a kref covered tty reference. That ensures the tty structure
doesn't go away when you have a return from get_current_tty. This is not
enough to protect you from most of the resources being freed behind your
back - yet.
[Updated to include fixes for SELinux problems found by Andrew Morton and
an s390 leak found while debugging the former]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Multipath is best at handling transport errors. If it gets a device
error then there is not much the multipath layer can do. It will just
access the same device but from a different path.
This patch breaks up failfast into device, transport and driver errors.
The multipath layers (md and dm mutlipath) only ask the lower levels to
fast fail transport errors. The user of failfast, read ahead, will ask
to fast fail on all errors.
Note that blk_noretry_request will return true if any failfast bit
is set. This allows drivers that do not support the multipath failfast
bits to continue to fail on any failfast error like before. Drivers
like scsi that are able to fail fast specific errors can check
for the specific fail fast type. In the next patch I will convert
scsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1075 commits)
myri10ge: update driver version number to 1.4.3-1.369
r8169: add shutdown handler
r8169: preliminary 8168d support
r8169: support additional 8168cp chipset
r8169: change default behavior for mildly identified 8168c chipsets
r8169: add a new 8168cp flavor
r8169: add a new 8168c flavor (bis)
r8169: add a new 8168c flavor
r8169: sync existing 8168 device hardware start sequences with vendor driver
r8169: 8168b Tx performance tweak
r8169: make room for more specific 8168 hardware start procedure
r8169: shuffle some registers handling around (8168 operation only)
r8169: new phy init parameters for the 8168b
r8169: update phy init parameters
r8169: wake up the PHY of the 8168
af_key: fix SADB_X_SPDDELETE response
ath9k: Fix return code when ath9k_hw_setpower() fails on reset
ath9k: remove nasty FAIL macro from ath9k_hw_reset()
gre: minor cleanups in netlink interface
gre: fix copy and paste error
...
The 3215 console irq handler used to schedule a tasklet. However the
console irq handler also gets called from the infamous cio_tpi()
function. Which in turn does something like
local_bh_disable()
[call console irq handler]
_local_bh_enable()
_local_bh_enable() prevents execution of softirqs, which is intended
within cio_tpi(). However there might be a new softirq pending because
irq handler scheduled a tasklet.
In order to prevent this behaviour we just get rid of the tasklet.
It's not doing much anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 console drivers use the unblank callback of the console
structure to flush the console buffer. In case of a panic or a
reboot the CPU doing the callback can block on the console i/o.
The other CPUs in the system continue to work. For panic this is
not a good idea.
Replace the unblank callback with proper panic/reboot notifier.
These get called after all but one CPU have been stopped.
Signed-off-by: Holger Smolinski <Holger.Smolinski@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
EMC Symmetrix Subsystem Control I/O through CKD dasd requires a
specific parameter list sent to the array via a Perform Subsystem
Function CCW. The Symmetrix response is retrieved from the array
via a Read Subsystem Data CCW.
Signed-off-by: Nigel Hislop <hislop_nigel@emc.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The xpram driver uses a single block device queue for all of its
devices so far. With recent kernels removing xpram module fails to
clean up all sysfs files. The next time the xpram module is loaded
you'll get warnings:
WARNING: at fs/sysfs/dir.c:463 sysfs_add_one+0x5e/0x64()
sysfs: duplicate filename '35:0' can not be created
Modules linked in: xpram(+) [last unloaded: xpram]
Followed by the usual WARN_ON output, followed by an error message
from kobject_add_internal, followed by a badness in genhd. Allocating
a block queue per device fixes this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the unsolicited interupt handler fake IRBs from CIO have to be
ignored because there is nothing to do.
The function dump_sense should not be called if there is no sense
data available.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Frank Blaschka