Now CPSW ALE will set/clean Host port bit in Unregistered Multicast Flood
Mask (UNREG_MCAST_FLOOD_MASK) for every VLAN without checking if this port
belongs to VLAN or not when ALLMULTI mode flag is set for nedev. This is
working in non dual_mac mode, but in dual_mac - it causes
enabling/disabling ALLMULTI flag for both ports.
Hence fix it by adding additional parameter to cpsw_ale_set_allmulti() to
specify ALE port number for which ALLMULTI has to be enabled and check if
port belongs to VLAN before modifying UNREG_MCAST_FLOOD_MASK.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace textual license with SPDX-License-Identifier.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It allows to use function under callbacks with same const qualifier of
mac address for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpsw_ale_create in cpsw_ale_create(). This also makes
cpsw_ale_destroy() function nop, so remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NetCP NU Switch ALE, some of the mask bits are different than
defaults used in the driver. Add a new macro DEFINE_ALE_FIELD1 that use
a configurable mask bits and use it in the driver. These bits are set to
correct values by using the new variables added to cpsw_ale structure
and re-used in the macros. The parameter nu_switch_ale is configured by
the caller driver to indicate the ALE is for that switch and is used in
the ALE driver to do customization as needed.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In NU Ethernet switch used on some of the Keystone SoCs, there is
separate UNKNOWNVLAN register for membership, unreg mcast flood, reg
mcast flood and force untag egress bits in ALE. So control for these
fields require different address offset, shift and size of field.
As this ALE has the same version number as ALE in CPSW found on other
SoCs, customization based on version number is not possible. So
use a configuration parameter, nu_switch_ale, to identify the ALE
ALE found in NU Switch. Different treatment is needed for NU Switch
ALE due to difference in the ale table bits, separate unknown vlan
registers etc. The register information available in ale_controls,
needs to be updated to support the netcp NU switch h/w. So it is not
constant array any more since it needs to be updated based
on ALE type. The header of the file is also updated to indicate it
supports N port switch ALE, not just 3 port. The version mask is
3 bits in NU Switch ALE vs 8 bits on other ALE types.
While at it, change the debug print to info print so that ALE
version gets displayed in boot log.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The funtions, cpsw_ale_flush and cpsw_ale_set_ageout, have never been used
since they were first introduced. This patch removes the dead code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to view addresses added by the driver and learnt by the
hardware from ALE table via ethtool register dump interface.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adding support for VLAN interface for cpsw.
CPSW VLAN Capability
* Can filter VLAN packets in Hardware
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper functions for VLAN ALE implementations for Add, Delete
Dump VLAN related ALE entries
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding multicast address to ALE table via netdev ops to subscribe, transmit
or receive multicast frames to and from the network
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPSW ethernet switch has a built-in address lookup engine. This patch adds
the code necessary for programming this module.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko