Since ceeeb99cd8 we no longer abuse the DMA_CTRL_ACK flag for custom
driver use and introduced the MXS_DMA_CTRL_WAIT4END instead. We have not
changed all users to this flag though. This patch fixes it for the
mxs-mmc driver.
Fixes: ceeeb99cd8 ("dmaengine: mxs: rename custom flag")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Reported-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a write memory barrier to make sure that descriptors are actually
written to memory, before ringing the doorbell.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the App note[1] detailing the tuning algorithm, for
temperatures < -20C, the initial tuning value should be min(largest value
in LPW - 24, ceil(13/16 ratio of LPW)). The largest value in LPW is
(max_window + 4 * (max_len - 1)) and not (max_window + 4 * max_len) itself.
Fix this implementation.
[1] http://www.ti.com/lit/an/spraca9b/spraca9b.pdf
Fixes: 961de0a856 ("mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:
sh_mmcif ee200000.mmc: IRQ index 1 not found
Fix this by calling platform_get_irq_optional() instead for the second
interrupt, which is optional.
Remove the now superfluous error printing for the first interrupt, which
is mandatory.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
renesas_sdhi_internal_dmac ee140000.sd: IRQ index 1 not found
Fix this by using the platform_irq_count() helper to avoid touching
non-existent interrupts.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the GL9750 and GL9755 chipsets.
Enable v4 mode and wait 5ms after set 1.8V signal enable for GL9750/
GL9755. Fix the value of SDHCI_MAX_CURRENT register and use the vendor
tuning flow for GL9750.
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller on Tegra186 supports 40-bit addressing, which is
usually enough to address all of system memory. However, if the SDHCI
controller is behind an IOMMU, the address space can go beyond. This
happens on Tegra186 and later where the ARM SMMU has an input address
space of 48 bits. If the DMA API is backed by this ARM SMMU, the top-
down IOVA allocator will cause IOV addresses to be returned that the
SDHCI controller cannot access.
Unfortunately, prior to the introduction of the ->set_dma_mask() host
operation, the SDHCI core would set either a 64-bit DMA mask if the
controller claimed to support 64-bit addressing, or a 32-bit DMA mask
otherwise.
Since the full 64 bits cannot be addressed on Tegra, this had to be
worked around in commit 68481a7e1c ("mmc: tegra: Mark 64 bit dma
broken on Tegra186") by setting the SDHCI_QUIRK2_BROKEN_64_BIT_DMA
quirk, which effectively restricts the DMA mask to 32 bits.
One disadvantage of this is that dma_map_*() APIs will now try to use
the swiotlb to bounce DMA to addresses beyond of the controller's DMA
mask. This in turn caused degraded performance and can lead to
situations where the swiotlb buffer is exhausted, which in turn leads
to DMA transfers to fail.
With the recent introduction of the ->set_dma_mask() host operation,
this can now be properly fixed. For each generation of Tegra, the exact
supported DMA mask can be configured. This kills two birds with one
stone: it avoids the use of bounce buffers because system memory never
exceeds the addressable memory range of the SDHCI controllers on these
devices, and at the same time when an IOMMU is involved, it prevents
IOV addresses from being allocated beyond the addressible range of the
controllers.
Since the DMA mask is now properly handled, the 64-bit DMA quirk can be
removed.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[treding@nvidia.com: provide more background in commit message]
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.15 +
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We must not unconditionally set the DMA snoop bit; if the DMA API is
assuming that the device is not DMA coherent, and the device snoops the
CPU caches, the device can see stale cache lines brought in by
speculative prefetch.
This leads to the device seeing stale data, potentially resulting in
corrupted data transfers. Commonly, this results in a descriptor fetch
error such as:
mmc0: ADMA error
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00002202
mmc0: sdhci: Blk size: 0x00000008 | Blk cnt: 0x00000001
mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
mmc0: sdhci: Present: 0x01f50008 | Host ctl: 0x00000038
mmc0: sdhci: Power: 0x00000003 | Blk gap: 0x00000000
mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x000040d8
mmc0: sdhci: Timeout: 0x00000003 | Int stat: 0x00000001
mmc0: sdhci: Int enab: 0x037f108f | Sig enab: 0x037f108b
mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00002202
mmc0: sdhci: Caps: 0x35fa0000 | Caps_1: 0x0000af00
mmc0: sdhci: Cmd: 0x0000333a | Max curr: 0x00000000
mmc0: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x001d8a33
mmc0: sdhci: Resp[2]: 0x325b5900 | Resp[3]: 0x3f400e00
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ADMA Err: 0x00000009 | ADMA Ptr: 0x000000236d43820c
mmc0: sdhci: ============================================
mmc0: error -5 whilst initialising SD card
but can lead to other errors, and potentially direct the SDHCI
controller to read/write data to other memory locations (e.g. if a valid
descriptor is visible to the device in a stale cache line.)
Fix this by ensuring that the DMA snoop bit corresponds with the
behaviour of the DMA API. Since the driver currently only supports DT,
use of_dma_is_coherent(). Note that device_get_dma_attr() can not be
used as that risks re-introducing this bug if/when the driver is
converted to ACPI.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA errors are potentially data corrupting events; although we print
the register state, we do not usefully print the ADMA descriptors.
Worse than that, we print them by referencing their virtual address
which is meaningless when the register state gives us the DMA address
of the failing descriptor.
Print the ADMA descriptors giving their DMA addresses rather than their
virtual addresses, and print them using SDHCI_DUMP() rather than DBG().
We also do not show the correct value of the interrupt status register;
the register dump shows the current value, after we have cleared the
pending interrupts we are going to service. What is more useful is to
print the interrupts that _were_ pending at the time the ADMA error was
encountered. Fix that too.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- add dma-mapping and block layer helpers to take care of IOMMU
merging for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask (me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
-----BEGIN PGP SIGNATURE-----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=/wGv
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- add dma-mapping and block layer helpers to take care of IOMMU merging
for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask
(me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
* tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping: (41 commits)
mmc: renesas_sdhi_internal_dmac: Add MMC_CAP2_MERGE_CAPABLE
mmc: queue: Fix bigger segments usage
arm64: use asm-generic/dma-mapping.h
swiotlb-xen: merge xen_unmap_single into xen_swiotlb_unmap_page
swiotlb-xen: simplify cache maintainance
swiotlb-xen: use the same foreign page check everywhere
swiotlb-xen: remove xen_swiotlb_dma_mmap and xen_swiotlb_dma_get_sgtable
xen: remove the exports for xen_{create,destroy}_contiguous_region
xen/arm: remove xen_dma_ops
xen/arm: simplify dma_cache_maint
xen/arm: use dev_is_dma_coherent
xen/arm: consolidate page-coherent.h
xen/arm: use dma-noncoherent.h calls for xen-swiotlb cache maintainance
arm: remove wrappers for the generic dma remap helpers
dma-mapping: introduce a dma_common_find_pages helper
dma-mapping: always use VM_DMA_COHERENT for generic DMA remap
vmalloc: lift the arm flag for coherent mappings to common code
dma-mapping: provide a better default ->get_required_mask
dma-mapping: remove the dma_declare_coherent_memory export
remoteproc: don't allow modular build
...
Accessing the device when it may be runtime suspended is a bug, which is
the case in tmio_mmc_host_remove(). Let's fix the behaviour.
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
The tmio_mmc_host_probe() calls pm_runtime_set_active() to update the
runtime PM status of the device, as to make it reflect the current status
of the HW. This works fine for most cases, but unfortunate not for all.
Especially, there is a generic problem when the device has a genpd attached
and that genpd have the ->start|stop() callbacks assigned.
More precisely, if the driver calls pm_runtime_set_active() during
->probe(), genpd does not get to invoke the ->start() callback for it,
which means the HW isn't really fully powered on. Furthermore, in the next
phase, when the device becomes runtime suspended, genpd will invoke the
->stop() callback for it, potentially leading to usage count imbalance
problems, depending on what's implemented behind the callbacks of course.
To fix this problem, convert to call pm_runtime_get_sync() from
tmio_mmc_host_probe() rather than pm_runtime_set_active(). Additionally, to
avoid bumping usage counters and unnecessary re-initializing the HW the
first time the tmio driver's ->runtime_resume() callback is called,
introduce a state flag to keeping track of this.
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
This reverts commit 7ff2131933.
It turns out that the above commit introduces other problems. For example,
calling pm_runtime_set_active() must not be done prior calling
pm_runtime_enable() as that makes it fail. This leads to additional
problems, such as clock enables being wrongly balanced.
Rather than fixing the problem on top, let's start over by doing a revert.
Fixes: 7ff2131933 ("mmc: tmio: move runtime PM enablement to the driver implementations")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Since this host controller can merge bigger segments if DMA API
layer cam merge the segments, this patch adds the flag.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The commit 38c38cb732 ("mmc: queue: use bigger segments if DMA MAP
layer can merge the segments") always enables the bugger segments
if DMA MAP layer can merge the segments, but some controllers (SDHCI)
have strictly limitation about the segments size, and then the commit
breaks on the controllers.
To fix the issue, this patch adds a new flag MMC_CAP2_MERGE_CAPABLE
into the struct mmc_host and the bigger segments usage is disabled
as default.
Reported-by: Thierry Reding <treding@nvidia.com>
Fixes: 38c38cb732 ("mmc: queue: use bigger segments if DMA MAP layer can merge the segments")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Don't populate the array degrees on the stack but instead make it
static const. Makes the object code smaller by 46 bytes.
Before:
text data bss dec hex filename
5356 1560 0 6916 1b04 dw_mmc-hi3798cv200.o
After:
text data bss dec hex filename
5214 1656 0 6870 1ad6 dw_mmc-hi3798cv200.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of keeping track of whether SDIO IRQs have been enabled via an
internal sdhci status flag, avoid the open-coding and convert into using
sdio_irq_claimed().
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.
However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).
Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_ack_sdio_irq() is called only when SDIO IRQs are enabled.
Therefore, let's drop the redundant check of the internal
SDHCI_SDIO_IRQ_ENABLED flag and just re-enable the IRQs immediately.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
System suspend/resume of SDIO cards, with SDIO IRQs enabled and when using
MMC_CAP2_SDIO_IRQ_NOTHREAD is unfortunate still suffering from a fragile
behaviour. Some problems have been taken care of so far, but more issues
remains.
For example, calling the ->ack_sdio_irq() callback to let host drivers
re-enable the SDIO IRQs is a bad idea, unless the IRQ have been consumed,
which may not be the case during system suspend/resume. This may lead to
that a host driver re-signals the same SDIO IRQ over and over again,
causing a storm of IRQs and gives a ping-pong effect towards the
sdio_irq_work().
Moreover, calling the ->enable_sdio_irq() callback at system resume to
re-enable already enabled SDIO IRQs for the host, causes the runtime PM
count for some host drivers to become in-balanced. This then leads to the
host to remain runtime resumed, no matter if it's needed or not.
To fix these problems, let's check if process_sdio_pending_irqs() actually
consumed the SDIO IRQ, before we continue to ack the IRQ by invoking the
->ack_sdio_irq() callback.
Additionally, there should be no need to re-enable SDIO IRQs as the host
driver already knows if they were enabled at system suspend, thus also
whether it needs to re-enable them at system resume. For this reason, drop
the call to ->enable_sdio_irq() during system resume.
In regards to these changes there is yet another issue, which is when there
is an SDIO IRQ being signaled by the host driver, but after the SDIO card
has been system suspended. Currently these IRQs are just thrown away, while
we should at least make sure to try to consume them when the SDIO card has
been system resumed. Fix this by queueing a sdio_irq_work() after we system
resumed the SDIO card.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make sure SDIO func drivers behaves correctly during system
suspend/resume, let add a WARN_ON in case the condition is a non-powered
SDIO card and there are some SDIO IRQs still being claimed.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the MMC_CAP2_SDIO_IRQ_NOTHREAD case and when using sdio_signal_irq(),
the ->ack_sdio_irq() is already mandatory, which was not the case for those
host drivers that called sdio_run_irqs() directly.
As there are no longer any drivers calling sdio_run_irqs(), let's clarify
the code by dropping the unnecessary check and explicitly state that the
callback is mandatory in the header file.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdio_irq_pending flag is used to let host drivers indicate that it has
signaled an IRQ. If that is the case and we only have a single SDIO func
that have claimed an SDIO IRQ, our assumption is that we can avoid reading
the SDIO_CCCR_INTx register and just call the SDIO func irq handler
immediately. This makes sense, but the flag is set/cleared in a somewhat
messy order, let's fix that up according to below.
First, the flag is currently set in sdio_run_irqs(), which is executed as a
work that was scheduled from sdio_signal_irq(). To make it more implicit
that the host have signaled an IRQ, let's instead immediately set the flag
in sdio_signal_irq(). This also makes the behavior consistent with host
drivers that uses the legacy, mmc_signal_sdio_irq() API. This have no
functional impact, because we don't expect host drivers to call
sdio_signal_irq() until after the work (sdio_run_irqs()) have been executed
anyways.
Second, currently we never clears the flag when using the sdio_run_irqs()
work, but only when using the sdio_irq_thread(). Let make the behavior
consistent, by moving the flag to be cleared inside the common
process_sdio_pending_irqs() function. Additionally, tweak the behavior of
the flag slightly, by avoiding to clear it unless we processed the SDIO
IRQ. The purpose with this at this point, is to keep the information about
whether there have been an SDIO IRQ signaled by the host, so at system
resume we can decide to process it without reading the SDIO_CCCR_INTx
register.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To improve code quality, let's move the code that gets pending SDIO IRQs
from process_sdio_pending_irqs() into a dedicated function.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
[Ulf: Converted function into static]
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means msdc_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the mtk-sd
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the mtk-sd driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the mtk-sd driver, so let's do that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means dw_mci_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the dw_mmc
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the dw_mmc driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the dw_mmc driver, so let's do that.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix data read/write error in HS200 mode due to chip DLL lock phase shift
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change O2 Host PLL and DLL register name
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resolves the following build error reported by the 0-day bot:
ERROR: "of_platform_device_create" [drivers/mmc/host/sdhci-of-aspeed.ko] undefined!
SPARC does not set CONFIG_OF_ADDRESS so the symbol is missing. Depend on
CONFIG_OF_ADDRESS to ensure the driver is only built for supported
configurations.
Fixes: 2d28dbe042f4 ("mmc: sdhci-of-aspeed: Add support for the ASPEED SD controller")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a get_max_clock() handler to sdhci-of-aspeed to report f_max as the
maximum clock rate if it is set. This enables artificial limitation of
the bus speed via max-frequency in the devicetree for e.g. the AST2600
evaluation board where I was seeing errors at 200MHz.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The early-exit didn't seem to matter on the AST2500, but on the AST2600
the SD clock genuinely may not be running on entry to
aspeed_sdhci_set_clock(). Remove the early exit to ensure we always run
sdhci_enable_clk().
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use for_each_sg() macro instead of open coded variant.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save set clock in mmc_host actual_clock enabling exporting it via debugfs.
This will indicate the precise SD clock in I/O settings rather than only the
sometimes misleading requested clock.
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the DMA addresses are casted to (u64) for the upper 32bits
to avoid "right shift count >= width of type" warning.
<linux/kernel.h> provides macros to address this, and I like the macro
names are self-documenting.
I introduced a new helper, sdhci_set_adma_addr() to avoid the code
duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The datasheet of the IP (sd4hc) says it is compiatible with SDHCI v4,
but the spec version field in the version register is read as 2
(i.e. SDHCI_SPEC_300) based on the RTL provided by Cadence.
Socionext did not fix it up when it integrated the IP into the SoCs.
So, it is working as SDHCI v3.
It is not a real problem because there is no difference in the program
flow in sdhci.c between SDHCI_SPEC_300/400, but set the real version
just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
__sdhci_read_caps() does not modify *ver, *caps, or *caps1.
Probably, the caller of this function will want to constifythe
parameters passed in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO IRQ is not defaultly triggered by low level,
but by falling edge. It needs to set related register
to enable SDIO IRQ low level trigger function.
Otherwise the SDIO IRQ may be lost in some specail condition.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_abort_tuning() function symbols which are used by other SD Host
controller driver modules.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The GL9750 and GL9755 chipsets, and possibly others, require PLL Enable
setup as part of the internal clock setup as described in 3.2.1 Internal
Clock Setup Sequence of SD Host Controller Simplified Specification
Version 4.20.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to section 3.2.1 internal clock setup in SD Host Controller
Simplified Specifications 4.20, the timeout of loop for checking
internal clock stable is defined as 150ms.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on Intel's LGM(Lightning Mountain) SoC devices.
Therefore, add a new compatible, to adapt the Intel's LGM
eMMC PHY with arasan-sdhc controller to configure the PHY.
Signed-off-by: Ramuthevar Vadivel Muruganx <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of error, the function of_platform_device_create() returns
NULL pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make sure the sdhost driver doesn't use requests bigger than SWIOTLB
can handle.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sascha Hauer