The current error codes returned when a the per user per user
namespace limit are hit (EINVAL, EUSERS, and ENFILE) are wrong. I
asked for advice on linux-api and it we made clear that those were
the wrong error code, but a correct effor code was not suggested.
The best general error code I have found for hitting a resource limit
is ENOSPC. It is not perfect but as it is unambiguous it will serve
until someone comes up with a better error code.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Fix 'skb_vlan_pop' to use eth_type_vlan instead of directly comparing
skb->protocol to ETH_P_8021Q or ETH_P_8021AD.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 93515d53b1
"net: move vlan pop/push functions into common code"
skb_vlan_pop was moved from its private location in openvswitch to
skbuff common code.
In case skb has non hw-accel vlan tag, the original 'pop_vlan()' assured
that skb->len is sufficient (if skb->len < VLAN_ETH_HLEN then pop was
considered a no-op).
This validation was moved as is into the new common 'skb_vlan_pop'.
Alas, in its original location (openvswitch), there was a guarantee that
'data' points to the mac_header, therefore the 'skb->len < VLAN_ETH_HLEN'
condition made sense.
However there's no such guarantee in the generic 'skb_vlan_pop'.
For short packets received in rx path going through 'skb_vlan_pop',
this causes 'skb_vlan_pop' to fail pop-ing a valid vlan hdr (in the non
hw-accel case) or to fail moving next tag into hw-accel tag.
Remove the 'skb->len < VLAN_ETH_HLEN' condition entirely:
It is superfluous since inner '__skb_vlan_pop' already verifies there
are VLAN_ETH_HLEN writable bytes at the mac_header.
Note this presents a slight change to skb_vlan_pop() users:
In case total length is smaller than VLAN_ETH_HLEN, skb_vlan_pop() now
returns an error, as opposed to previous "no-op" behavior.
Existing callers (e.g. tc act vlan, ovs) usually drop the packet if
'skb_vlan_pop' fails.
Fixes: 93515d53b1 ("net: move vlan pop/push functions into common code")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Pravin Shelar <pshelar@ovn.org>
Reviewed-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This exports the functionality of extracting the tag from the payload,
without moving next vlan tag into hw accel tag.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work implements direct packet access for helpers and direct packet
write in a similar fashion as already available for XDP types via commits
4acf6c0b84 ("bpf: enable direct packet data write for xdp progs") and
6841de8b0d ("bpf: allow helpers access the packet directly"), and as a
complementary feature to the already available direct packet read for tc
(cls/act) programs.
For enabling this, we need to introduce two helpers, bpf_skb_pull_data()
and bpf_csum_update(). The first is generally needed for both, read and
write, because they would otherwise only be limited to the current linear
skb head. Usually, when the data_end test fails, programs just bail out,
or, in the direct read case, use bpf_skb_load_bytes() as an alternative
to overcome this limitation. If such data sits in non-linear parts, we
can just pull them in once with the new helper, retest and eventually
access them.
At the same time, this also makes sure the skb is uncloned, which is, of
course, a necessary condition for direct write. As this needs to be an
invariant for the write part only, the verifier detects writes and adds
a prologue that is calling bpf_skb_pull_data() to effectively unclone the
skb from the very beginning in case it is indeed cloned. The heuristic
makes use of a similar trick that was done in 233577a220 ("net: filter:
constify detection of pkt_type_offset"). This comes at zero cost for other
programs that do not use the direct write feature. Should a program use
this feature only sparsely and has read access for the most parts with,
for example, drop return codes, then such write action can be delegated
to a tail called program for mitigating this cost of potential uncloning
to a late point in time where it would have been paid similarly with the
bpf_skb_store_bytes() as well. Advantage of direct write is that the
writes are inlined whereas the helper cannot make any length assumptions
and thus needs to generate a call to memcpy() also for small sizes, as well
as cost of helper call itself with sanity checks are avoided. Plus, when
direct read is already used, we don't need to cache or perform rechecks
on the data boundaries (due to verifier invalidating previous checks for
helpers that change skb->data), so more complex programs using rewrites
can benefit from switching to direct read plus write.
For direct packet access to helpers, we save the otherwise needed copy into
a temp struct sitting on stack memory when use-case allows. Both facilities
are enabled via may_access_direct_pkt_data() in verifier. For now, we limit
this to map helpers and csum_diff, and can successively enable other helpers
where we find it makes sense. Helpers that definitely cannot be allowed for
this are those part of bpf_helper_changes_skb_data() since they can change
underlying data, and those that write into memory as this could happen for
packet typed args when still cloned. bpf_csum_update() helper accommodates
for the fact that we need to fixup checksum_complete when using direct write
instead of bpf_skb_store_bytes(), meaning the programs can use available
helpers like bpf_csum_diff(), and implement csum_add(), csum_sub(),
csum_block_add(), csum_block_sub() equivalents in eBPF together with the
new helper. A usage example will be provided for iproute2's examples/bpf/
directory.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 8a29111c7 ("net: gro: allow to build full sized skb")
gro may build buffers with a frag_list. This can hurt forwarding
because most NICs can't offload such packets, they need to be
segmented in software. This patch splits buffers with a frag_list
at the frag_list pointer into buffers that can be TSO offloaded.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is cloned, the associated sock_cgroup_data is duplicated
but not its reference on the cgroup. As a result, the cgroup reference
count will underflow when both sockets are destroyed later on.
Fixes: bd1060a1d6 ("sock, cgroup: add sock->sk_cgroup")
Link: http://lkml.kernel.org/r/20160914194846.11153-2-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a nested attribute of offload stats to if_stats_msg
named IFLA_STATS_LINK_OFFLOAD_XSTATS.
Under it, add SW stats, meaning stats only per packets that went via
slowpath to the cpu, named IFLA_OFFLOAD_XSTATS_CPU_HIT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds BPF_CALL_<n>() macros and converts all the eBPF helper functions
to use them, in a similar fashion like we do with SYSCALL_DEFINE<n>() macros
that are used today. Motivation for this is to hide all the register handling
and all necessary casts from the user, so that it is done automatically in the
background when adding a BPF_CALL_<n>() call.
This makes current helpers easier to review, eases to write future helpers,
avoids getting the casting mess wrong, and allows for extending all helpers at
once (f.e. build time checks, etc). It also helps detecting more easily in
code reviews that unused registers are not instrumented in the code by accident,
breaking compatibility with existing programs.
BPF_CALL_<n>() internals are quite similar to SYSCALL_DEFINE<n>() ones with some
fundamental differences, for example, for generating the actual helper function
that carries all u64 regs, we need to fill unused regs, so that we always end up
with 5 u64 regs as an argument.
I reviewed several 0-5 generated BPF_CALL_<n>() variants of the .i results and
they look all as expected. No sparse issue spotted. We let this also sit for a
few days with Fengguang's kbuild test robot, and there were no issues seen. On
s390, it barked on the "uses dynamic stack allocation" notice, which is an old
one from bpf_perf_event_output{,_tp}() reappearing here due to the conversion
to the call wrapper, just telling that the perf raw record/frag sits on stack
(gcc with s390's -mwarn-dynamicstack), but that's all. Did various runtime tests
and they were fine as well. All eBPF helpers are now converted to use these
macros, getting rid of a good chunk of all the raw castings.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fetching ifindex, we don't need to test dev for being NULL since
we're always guaranteed to have a valid dev for clsact programs. Thus,
avoid this test in fast path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add BPF_SIZEOF() and BPF_FIELD_SIZEOF() macros to improve the code a bit
which otherwise often result in overly long bytes_to_bpf_size(sizeof())
and bytes_to_bpf_size(FIELD_SIZEOF()) lines. So place them into a macro
helper instead. Moreover, we currently have a BUILD_BUG_ON(BPF_FIELD_SIZEOF())
check in convert_bpf_extensions(), but we should rather make that generic
as well and add a BUILD_BUG_ON() test in all BPF_SIZEOF()/BPF_FIELD_SIZEOF()
users to detect any rewriter size issues at compile time. Note, there are
currently none, but we want to assert that it stays this way.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor misc cleanups, f.e. use sizeof(__u32) instead of hardcoding
and in __bpf_skb_max_len(), I missed that we always have skb->dev valid
anyway, so we can drop the unneeded test for dev; also few more other
misc bits addressed here.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure is defined but never used. Flagged with W=1
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the years, TCP BDP has increased by several orders of magnitude,
and some people are considering to reach the 2 Gbytes limit.
Even with current window scale limit of 14, ~1 Gbytes maps to ~740,000
MSS.
In presence of packet losses (or reorders), TCP stores incoming packets
into an out of order queue, and number of skbs sitting there waiting for
the missing packets to be received can be in the 10^5 range.
Most packets are appended to the tail of this queue, and when
packets can finally be transferred to receive queue, we scan the queue
from its head.
However, in presence of heavy losses, we might have to find an arbitrary
point in this queue, involving a linear scan for every incoming packet,
throwing away cpu caches.
This patch converts it to a RB tree, to get bounded latencies.
Yaogong wrote a preliminary patch about 2 years ago.
Eric did the rebase, added ofo_last_skb cache, polishing and tests.
Tested with network dropping between 1 and 10 % packets, with good
success (about 30 % increase of throughput in stress tests)
Next step would be to also use an RB tree for the write queue at sender
side ;)
Signed-off-by: Yaogong Wang <wygivan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-By: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following few steps will crash kernel -
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never read or change netns id in hardirq context,
the only place we read netns id in softirq context
is in vxlan_xmit(). So, it should be enough to just
disable BH.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netns id should be already allocated each time we change
netns, that is, in dev_change_net_namespace() (more precisely
in rtnl_fill_ifinfo()). It is safe to just call peernet2id() here.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original codes depend on that the function parameters are evaluated from
left to right. But the parameter's evaluation order is not defined in C
standard actually.
When flow_keys_have_l4(&keys) is invoked before ___skb_get_hash(skb, &keys,
hashrnd) with some compilers or environment, the keys passed to
flow_keys_have_l4 is not initialized.
Fixes: 6db61d79c1 ("flow_dissector: Ignore flow dissector return value from ___skb_get_hash")
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb dumps spanning multiple skb's currently restart from the first
interface again for every skb. This results in unnecessary
iterations on the already visited interfaces and their fdb
entries. In large scale setups, we have seen this to slow
down fdb dumps considerably. On a system with 30k macs we
see fdb dumps spanning across more than 300 skbs.
To fix the problem, this patch replaces the existing single fdb
marker with three markers: netdev hash entries, netdevs and fdb
index to continue where we left off instead of restarting from the
first netdev. This is consistent with link dumps.
In the process of fixing the performance issue, this patch also
re-implements fix done by
commit 472681d57a ("net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump")
(with an internal fix from Wilson Kok) in the following ways:
- change ndo_fdb_dump handlers to return error code instead
of the last fdb index
- use cb->args strictly for dump frag markers and not error codes.
This is consistent with other dump functions.
Below results were taken on a system with 1000 netdevs
and 35085 fdb entries:
before patch:
$time bridge fdb show | wc -l
15065
real 1m11.791s
user 0m0.070s
sys 1m8.395s
(existing code does not return all macs)
after patch:
$time bridge fdb show | wc -l
35085
real 0m2.017s
user 0m0.113s
sys 0m1.942s
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today mpls iptunnel lwtunnel_output redirect expects the tunnel
output function to handle fragmentation. This is ok but can be
avoided if we did not do the mpls output redirect too early.
ie we could wait until ip fragmentation is done and then call
mpls output for each ip fragment.
To make this work we will need,
1) the lwtunnel state to carry encap headroom
2) and do the redirect to the encap output handler on the ip fragment
(essentially do the output redirect after fragmentation)
This patch adds tunnel headroom in lwtstate to make sure we
account for tunnel data in mtu calculations during fragmentation
and adds new xmit redirect handler to redirect to lwtunnel xmit func
after ip fragmentation.
This includes IPV6 and some mtu fixes and testing from David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 145dd5f9c8 ("net: flush the softnet backlog in process
context"), we can easily batch calls to flush_all_backlogs() for all
devices processed in rollback_registered_many()
Tested:
Before patch, on an idle host.
modprobe dummy numdummies=10000
perf stat -e context-switches -a rmmod dummy
Performance counter stats for 'system wide':
1,211,798 context-switches
1.302137465 seconds time elapsed
After patch:
perf stat -e context-switches -a rmmod dummy
Performance counter stats for 'system wide':
225,523 context-switches
0.721623566 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of
port netdevs so that packets being flooded by the device won't be
flooded twice.
It works by assigning a unique identifier (the ifindex of the first
bridge port) to bridge ports sharing the same parent ID. This prevents
packets from being flooded twice by the same switch, but will flood
packets through bridge ports belonging to a different switch.
This method is problematic when stacked devices are taken into account,
such as VLANs. In such cases, a physical port netdev can have upper
devices being members in two different bridges, thus requiring two
different 'offload_fwd_mark's to be configured on the port netdev, which
is impossible.
The main problem is that packet and netdev marking is performed at the
physical netdev level, whereas flooding occurs between bridge ports,
which are not necessarily port netdevs.
Instead, packet and netdev marking should really be done in the bridge
driver with the switch driver only telling it which packets it already
forwarded. The bridge driver will mark such packets using the mark
assigned to the ingress bridge port and will prevent the packet from
being forwarded through any bridge port sharing the same mark (i.e.
having the same parent ID).
Remove the current switchdev 'offload_fwd_mark' implementation and
instead implement the proposed method. In addition, make rocker - the
sole user of the mark - use the proposed method.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in process_backlog(), the process_queue dequeuing is
performed with local IRQ disabled, to protect against
flush_backlog(), which runs in hard IRQ context.
This patch moves the flush operation to a work queue and runs the
callback with bottom half disabled to protect the process_queue
against dequeuing.
Since process_queue is now always manipulated in bottom half context,
the irq disable/enable pair around the dequeue operation are removed.
To keep the flush time as low as possible, the flush
works are scheduled on all online cpu simultaneously, using the
high priority work-queue and statically allocated, per cpu,
work structs.
Overall this change increases the time required to destroy a device
to improve slightly the packets reinjection performances.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer use this handler, we can delete it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer use SLAB_DESTROY_BY_RCU for UDP,
we do not need sk_prot_clear_portaddr_nulls() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the features bit field has bits for internal only use as well, it
may happen that the kernel exports RTAX_FEATURES attribute with zero
value which is pointless.
Fix this by making sure the attribute is added only if the exported
value is non-zero.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
As recently discussed during the task_under_cgroup_hierarchy() addition,
we should get rid of the ifdefs surrounding the bpf_skb_under_cgroup()
helper. If related functionality is not built-in, the helper cannot be
used anyway, which is also in line with what we do for all other helpers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up to 555c8a8623 ("bpf: avoid stack copy and use skb ctx for
event output") for also adding the event output helper for XDP typed
programs. The event output helper has been very useful in particular for
debugging or event notification purposes, since it's much faster and
flexible than regular trace printk due to programmatically being able to
attach meta data. Same flags structure applies as with tc BPF programs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a bpf_skb_change_tail() helper for tc BPF programs. The
basic idea is to expand or shrink the skb in a controlled manner. The
eBPF program can then rewrite the rest via helpers like bpf_skb_store_bytes(),
bpf_lX_csum_replace() and others rather than passing a raw buffer for
writing here.
bpf_skb_change_tail() is really a slow path helper and intended for
replies with f.e. ICMP control messages. Concept is similar to other
helpers like bpf_skb_change_proto() helper to keep the helper without
protocol specifics and let the BPF program mangle the remaining parts.
A flags field has been added and is reserved for now should we extend
the helper in future.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have a skb_pkt_type_ok() helper for checking the type before
mangling, make use of it instead of open coding. Follow-up to commit
8b10cab64c ("net: simplify and make pkt_type_ok() available for other
users") that came in after d2485c4242 ("bpf: add bpf_skb_change_type
helper").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vlan priority check to the flow dissector by adding new flow
dissector struct, flow_dissector_key_vlan which includes vlan tag
fields.
vlan_id and flow_label fields were under the same struct
(flow_dissector_key_tags). It was a convenient setting since struct
flow_dissector_key_tags is used by struct flow_keys and by setting
vlan_id and flow_label under the same struct, we get precisely 24 or 48
bytes in flow_keys from flow_dissector_key_basic.
Now, when adding vlan priority support, the code will be cleaner if
flow_label and vlan tag won't be under the same struct anymore.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early in the datapath skb_vlan_untag function is called, stripped
the vlan from the skb and set skb->vlan_tci and skb->vlan_proto fields.
The current dissection doesn't handle stripped vlan packets correctly.
In some flows, vlan doesn't exist in skb->data anymore when applying
flow dissection on the skb, fix that.
In case vlan info wasn't stripped before applying flow_dissector (RPS
flow for example), or in case of skb with multiple vlans (e.g. 802.1ad),
get the vlan info from skb->data. The flow_dissector correctly skips
any number of vlans and stores only the first level vlan.
Fixes: 0744dd00c1 ('net: introduce skb_flow_dissect()')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_NS is disabled, registering pernet operations causes
init() to be called immediately with init_net as an argument. Unfortunately
this leads to some pernet ops, such as proc_net_ns_init() to be called too
early, when init_net namespace has not been fully initialized. This causes
issues when we want to change pernet ops to use more data from the net
namespace in question, for example reference user namespace that owns our
network namespace.
To fix this we could either play game of musical chairs and rearrange init
order, or we could do the same as when CONFIG_NET_NS is enabled, and
postpone calling pernet ops->init() until namespace is set up properly.
Note that we can not simply undo commit ed160e839d ("[NET]: Cleanup
pernet operation without CONFIG_NET_NS") and use the same implementations
for __register_pernet_operations() and __unregister_pernet_operations(),
because many pernet ops are marked as __net_initdata and will be discarded,
which wreaks havoc on our ops lists. Here we rely on the fact that we only
use lists until init_net is fully initialized, which happens much earlier
than discarding __net_initdata sections.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea for type_check in dev_get_nest_level() was to count the number
of nested devices of the same type (currently, only macvlan or vlan
devices).
This prevented the false positive lockdep warning on configurations such
as:
eth0 <--- macvlan0 <--- vlan0 <--- macvlan1
However, this doesn't prevent a warning on a configuration such as:
eth0 <--- macvlan0 <--- vlan0
eth1 <--- vlan1 <--- macvlan1
In this case, all the locks end up with a nesting subclass of 1, so
lockdep thinks that there is still a deadlock:
- in the first case we have (macvlan_netdev_addr_lock_key, 1) and then
take (vlan_netdev_xmit_lock_key, 1)
- in the second case, we have (vlan_netdev_xmit_lock_key, 1) and then
take (macvlan_netdev_addr_lock_key, 1)
By removing the linktype check in dev_get_nest_level() and always
incrementing the nesting depth, lockdep considers this configuration
valid.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the bpf_try_make_writable() helper and all call sites we have in BPF,
it's currently defect with regards to skbs when the write_len spans into
non-linear parts, no matter if cloned or not.
There are multiple issues at once. First, using skb_store_bits() is not
correct since even if we have a cloned skb, page frags can still be shared.
To really make them private, we need to pull them in via __pskb_pull_tail()
first, which also gets us a private head via pskb_expand_head() implicitly.
This is for helpers like bpf_skb_store_bytes(), bpf_l3_csum_replace(),
bpf_l4_csum_replace(). Really, the only thing reasonable and working here
is to call skb_ensure_writable() before any write operation. Meaning, via
pskb_may_pull() it makes sure that parts we want to access are pulled in and
if not does so plus unclones the skb implicitly. If our write_len still fits
the headlen and we're cloned and our header of the clone is not writable,
then we need to make a private copy via pskb_expand_head(). skb_store_bits()
is a bit misleading and only safe to store into non-linear data in different
contexts such as 357b40a18b ("[IPV6]: IPV6_CHECKSUM socket option can
corrupt kernel memory").
For above BPF helper functions, it means after fixed bpf_try_make_writable(),
we've pulled in enough, so that we operate always based on skb->data. Thus,
the call to skb_header_pointer() and skb_store_bits() becomes superfluous.
In bpf_skb_store_bytes(), the len check is unnecessary too since it can
only pass in maximum of BPF stack size, so adding offset is guaranteed to
never overflow. Also bpf_l3/4_csum_replace() helpers must test for proper
offset alignment since they use __sum16 pointer for writing resulting csum.
The remaining helpers that change skb data not discussed here yet are
bpf_skb_vlan_push(), bpf_skb_vlan_pop() and bpf_skb_change_proto(). The
vlan helpers internally call either skb_ensure_writable() (pop case) and
skb_cow_head() (push case, for head expansion), respectively. Similarly,
bpf_skb_proto_xlat() takes care to not mangle page frags.
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Fixes: 91bc4822c3 ("tc: bpf: add checksum helpers")
Fixes: 3697649ff2 ("bpf: try harder on clones when writing into skb")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hashing out BPF's current_task_under_cgroup helper bits, it came
to discussion that the skb_in_cgroup helper name was suboptimally chosen.
Tejun says:
So, I think in_cgroup should mean that the object is in that
particular cgroup while under_cgroup in the subhierarchy of that
cgroup. Let's rename the other subhierarchy test to under too. I
think that'd be a lot less confusing going forward.
[...]
It's more intuitive and gives us the room to implement the real
"in" test if ever necessary in the future.
Since this touches uapi bits, we need to change this as long as v4.8
is not yet officially released. Thus, change the helper enum and rename
related bits.
Fixes: 4a482f34af ("cgroup: bpf: Add bpf_skb_in_cgroup_proto")
Reference: http://patchwork.ozlabs.org/patch/658500/
Suggested-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
The PPTP is encapsulated by GRE header with that GRE_VERSION bits
must contain one. But current GRE RPS needs the GRE_VERSION must be
zero. So RPS does not work for PPTP traffic.
In my test environment, there are four MIPS cores, and all traffic
are passed through by PPTP. As a result, only one core is 100% busy
while other three cores are very idle. After this patch, the usage
of four cores are balanced well.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the per-device linked list into a hashtable. The primary
motivation for this change is that currently, we're not tracking all the
qdiscs in hierarchy (e.g. excluding default qdiscs), as the lookup
performed over the linked list by qdisc_match_from_root() is rather
expensive.
The ultimate goal is to get rid of hidden qdiscs completely, which will
bring much more determinism in user experience.
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Admin should be able to set any state. Currently, this fails
when lladdr is not changed and state is changed from
NUD_CONNECTED to NUD_STALE:
ip neigh add 192.168.8.1 lladdr 00:11:22:33:44:55 nud perm dev wlan0
ip neigh show to 192.168.8.1
192.168.8.1 dev wlan0 lladdr 00:11:22:33:44:55 PERMANENT
ip neigh change 192.168.8.1 lladdr 00:11:22:33:44:55 nud stale dev wlan0
ip neigh show to 192.168.8.1
192.168.8.1 dev wlan0 lladdr 00:11:22:33:44:55 PERMANENT
Problem may be from 2.1.X days.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: Chunhui He <hchunhui@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When having skbs on ingress with CHECKSUM_COMPLETE, tc BPF programs don't
push rcsum of mac header back in and after BPF run back pull out again as
opposed to some other subsystems (ovs, for example).
For cases like q-in-q, meaning when a vlan tag for offloading is already
present and we're about to push another one, then skb_vlan_push() pushes the
inner one into the skb, increasing mac header and skb_postpush_rcsum()'ing
the 4 bytes vlan header diff. Likewise, for the reverse operation in
skb_vlan_pop() for the case where vlan header needs to be pulled out of the
skb, we're decreasing the mac header and skb_postpull_rcsum()'ing the 4 bytes
rcsum of the vlan header that was removed.
However mangling the rcsum here will lead to hw csum failure for BPF case,
since we're pulling or pushing data that was not part of the current rcsum.
Changing tc BPF programs in general to push/pull rcsum around BPF_PROG_RUN()
is also not really an option since current behaviour is ABI by now, but apart
from that would also mean to do quite a bit of useless work in the sense that
usually 12 bytes need to be rcsum pushed/pulled also when we don't need to
touch this vlan related corner case. One way to fix it would be to push the
necessary rcsum fixup down into vlan helpers that are (mostly) slow-path
anyway.
Fixes: 4e10df9a60 ("bpf: introduce bpf_skb_vlan_push/pop() helpers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up to commit f8ffad69c9 ("bpf: add skb_postpush_rcsum and fix
dev_forward_skb occasions") to fix an issue for dev_queue_xmit() redirect
locations which need CHECKSUM_COMPLETE fixups on ingress.
For the same reasons as described in f8ffad69c9 already, we of course
also need this here, since dev_queue_xmit() on a veth device will let us
end up in the dev_forward_skb() helper again to cross namespaces.
Latter then calls into skb_postpull_rcsum() to pull out L2 header, so
that netif_rx_internal() sees CHECKSUM_COMPLETE as it is expected. That
is, CHECKSUM_COMPLETE on ingress covering L2 _payload_, not L2 headers.
Also here we have to address bpf_redirect() and bpf_clone_redirect().
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the vfs dentry hashing to mix in the parent pointer at the
_beginning_ of the hash, rather than at the end.
That actually improves both the hash and the code generation, because we
can move more of the computation to the "static" part of the dcache
setup, and do less at lookup runtime.
It turns out that a lot of other hash users also really wanted to mix in
a base pointer as a 'salt' for the hash, and so the slightly extended
interface ends up working well for other cases too.
Users that want a string hash that is purely about the string pass in a
'salt' pointer of NULL.
* merge branch 'salted-string-hash':
fs/dcache.c: Save one 32-bit multiply in dcache lookup
vfs: make the string hashes salt the hash
NUD_STALE is used when the caller(e.g. arp_process()) can't guarantee
neighbour reachability. If the entry was NUD_VALID and lladdr is unchanged,
the entry state should not be changed.
Currently the code puts an extra "NUD_CONNECTED" condition. So if old state
was NUD_DELAY or NUD_PROBE (they are NUD_VALID but not NUD_CONNECTED), the
state can be changed to NUD_STALE.
This may cause problem. Because NUD_STALE lladdr doesn't guarantee
reachability, when we send traffic, the state will be changed to
NUD_DELAY. In normal case, if we get no confirmation (by dst_confirm()),
we will change the state to NUD_PROBE and send probe traffic. But now the
state may be reset to NUD_STALE again(e.g. by broadcast ARP packets),
so the probe traffic will not be sent. This situation may happen again and
again, and packets will be sent to an non-reachable lladdr forever.
The fix is to remove the "NUD_CONNECTED" condition. After that the
"NEIGH_UPDATE_F_WEAK_OVERRIDE" condition (used by IPv6) in that branch will
be redundant, so remove it.
This change may increase probe traffic, but it's essential since NUD_STALE
lladdr is unreliable. To ensure correctness, we prefer to resolve lladdr,
when we can't get confirmation, even while remote packets try to set
NUD_STALE state.
Signed-off-by: Chunhui He <hchunhui@mail.ustc.edu.cn>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the __output_custom() routine we currently use with
bpf_skb_copy(). I missed that when len is larger than the size of the
current handle, we can issue multiple invocations of copy_func, and
__output_custom() advances destination but also source buffer by the
written amount of bytes. When we have __output_custom(), this is actually
wrong since in that case the source buffer points to a non-linear object,
in our case an skb, which the copy_func helper is supposed to walk.
Therefore, since this is non-linear we thus need to pass the offset into
the helper, so that copy_func can use it for extracting the data from
the source object.
Therefore, adjust the callback signatures properly and pass offset
into the skb_header_pointer() invoked from bpf_skb_copy() callback. The
__DEFINE_OUTPUT_COPY_BODY() is adjusted to accommodate for two things:
i) to pass in whether we should advance source buffer or not; this is
a compile-time constant condition, ii) to pass in the offset for
__output_custom(), which we do with help of __VA_ARGS__, so everything
can stay inlined as is currently. Both changes allow for adapting the
__output_* fast-path helpers w/o extra overhead.
Fixes: 555c8a8623 ("bpf: avoid stack copy and use skb ctx for event output")
Fixes: 7e3f977edd ("perf, events: add non-linear data support for raw records")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IFLA_XDP_ATTACHED nested attribute is meant for read-only, and while
do_setlink properly ignores it, it should be more paranoid and reject
commands that try to set it.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sets the bpf program represented by fd as an early filter in the rx path
of the netdev. The fd must have been created as BPF_PROG_TYPE_XDP.
Providing a negative value as fd clears the program. Getting the fd back
via rtnl is not possible, therefore reading of this value merely
provides a bool whether the program is valid on the link or not.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add one new netdev op for drivers implementing the BPF_PROG_TYPE_XDP
filter. The single op is used for both setup/query of the xdp program,
modelled after ndo_setup_tc.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new bpf prog type that is intended to run in early stages of the
packet rx path. Only minimal packet metadata will be available, hence a
new context type, struct xdp_md, is exposed to userspace. So far only
expose the packet start and end pointers, and only in read mode.
An XDP program must return one of the well known enum values, all other
return codes are reserved for future use. Unfortunately, this
restriction is hard to enforce at verification time, so take the
approach of warning at runtime when such programs are encountered. Out
of bounds return codes should alias to XDP_ABORTED.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work addresses a couple of issues bpf_skb_event_output()
helper currently has: i) We need two copies instead of just a
single one for the skb data when it should be part of a sample.
The data can be non-linear and thus needs to be extracted via
bpf_skb_load_bytes() helper first, and then copied once again
into the ring buffer slot. ii) Since bpf_skb_load_bytes()
currently needs to be used first, the helper needs to see a
constant size on the passed stack buffer to make sure BPF
verifier can do sanity checks on it during verification time.
Thus, just passing skb->len (or any other non-constant value)
wouldn't work, but changing bpf_skb_load_bytes() is also not
the proper solution, since the two copies are generally still
needed. iii) bpf_skb_load_bytes() is just for rather small
buffers like headers, since they need to sit on the limited
BPF stack anyway. Instead of working around in bpf_skb_load_bytes(),
this work improves the bpf_skb_event_output() helper to address
all 3 at once.
We can make use of the passed in skb context that we have in
the helper anyway, and use some of the reserved flag bits as
a length argument. The helper will use the new __output_custom()
facility from perf side with bpf_skb_copy() as callback helper
to walk and extract the data. It will pass the data for setup
to bpf_event_output(), which generates and pushes the raw record
with an additional frag part. The linear data used in the first
frag of the record serves as programmatically defined meta data
passed along with the appended sample.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dccp verifies packet integrity, including length, at initial rcv in
dccp_invalid_packet, later pulls headers in dccp_enqueue_skb.
A call to sk_filter in-between can cause __skb_pull to wrap skb->len.
skb_copy_datagram_msg interprets this as a negative value, so
(correctly) fails with EFAULT. The negative length is reported in
ioctl SIOCINQ or possibly in a DCCP_WARN in dccp_close.
Introduce an sk_receive_skb variant that caps how small a filter
program can trim packets, and call this in dccp with the header
length. Excessively trimmed packets are now processed normally and
queued for reception as 0B payloads.
Fixes: 7c657876b6 ("[DCCP]: Initial implementation")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sockets can have a filter program attached that drops or trims
incoming packets based on the filter program return value.
Rose requires data packets to have at least ROSE_MIN_LEN bytes. It
verifies this on arrival in rose_route_frame and unconditionally pulls
the bytes in rose_recvmsg. The filter can trim packets to below this
value in-between, causing pull to fail, leaving the partial header at
the time of skb_copy_datagram_msg.
Place a lower bound on the size to which sk_filter may trim packets
by introducing sk_filter_trim_cap and call this for rose packets.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a tracepoint and allow user to trace messages going to and from
hardware associated with devlink instance.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Trofimovich reported that pulse audio sends SCM_CREDENTIALS
as a control message to TCP. Since __sock_cmsg_send does not
support SCM_RIGHTS and SCM_CREDENTIALS, it returns an error and
hence breaks pulse audio over TCP.
SCM_RIGHTS and SCM_CREDENTIALS are sent on the SOL_SOCKET layer
but they semantically belong to SOL_UNIX. Since all
cmsg-processing functions including sock_cmsg_send ignore control
messages of other layers, it is best to ignore SCM_RIGHTS
and SCM_CREDENTIALS for consistency (and also for fixing pulse
audio over TCP).
Fixes: c14ac9451c ("sock: enable timestamping using control messages")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Reported-by: Sergei Trofimovich <slyfox@gentoo.org>
Tested-by: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An important information for the napi_poll tracepoint is knowing
the work done (packets processed) by the napi_poll() call. Add
both the work done and budget, as they are related.
Handle trace_napi_poll() param change in dropwatch/drop_monitor
and in python perf script netdev-times.py in backward compat way,
as python fortunately supports optional parameter handling.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the data plane is offloaded the traffic doesn't go through the
networking stack. Therefore, after first resolving a neighbour the NUD
state machine will transition it from REACHABLE to STALE until it's
finally deleted by the garbage collector.
To prevent such situations the offloading driver should notify the NUD
state machine on any neighbours that were recently used. The driver's
polling interval should be set so that the NUD state machine can
function as if the traffic wasn't offloaded.
Currently, there are no in-tree drivers that can report confirmation for
a neighbour, but only 'used' indication. Therefore, the polling interval
should be set according to DELAY_FIRST_PROBE_TIME, as a neighbour will
transition from REACHABLE state to DELAY (instead of STALE) if "a packet
was sent within the last DELAY_FIRST_PROBE_TIME seconds" (RFC 4861).
Send a netevent whenever the DELAY_FIRST_PROBE_TIME changes - either via
netlink or sysctl - so that offloading drivers can correctly set their
polling interval.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 upper device needs to propagate neigh_construct/destroy calls down to
lower devices. Do this by defining default ndo functions and use them in
team, bond, bridge and vlan.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the following patch will allow upper devices to follow the call down
lower devices, we need to add dev here and not rely on n->dev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.
Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_clear_hash() was invoked due to mangling of relevant headers and
BPF program needs skb->hash later on, we can add a helper to trigger hash
recalculation via bpf_get_hash_recalc().
The helper will return the newly retrieved hash directly, but later access
can also be done via skb context again through skb->hash directly (inline)
without needing to call the helper once more.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add another xmit_mode to pktgen to allow testing xmit functionality
of qdiscs. The new mode "queue_xmit" injects packets at
__dev_queue_xmit() so that qdisc is called.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the commands to set and show the mode of SRIOV E-Switch, two modes
are supported:
* legacy: operating in the "old" L2 based mode (DMAC --> VF vport)
* switchdev: the E-Switch is referred to as whitebox switch configured
using standard tools such as tc, bridge, openvswitch etc. To allow
working with the tools, for each VF, a VF representor netdevice is
created by the E-Switch manager vendor device driver instance (e.g PF).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4 ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 9b368814b3 ("net: fix bridge multicast packet checksum validation")
we need to fixup the checksum for CHECKSUM_COMPLETE when
pushing skb on RX path. Otherwise we get similar splats.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People who use PACKET_FANOUT_HASH want a symmetric hash, meaning that
they want packets going in both directions on a flow to hash to the
same bucket.
The core kernel SKB hash became non-symmetric when the ipv6 flow label
and other entities were incorporated into the standard flow hash order
to increase entropy.
But there are no users of PACKET_FANOUT_HASH who want an assymetric
hash, they all want a symmetric one.
Therefore, use the flow dissector to compute a flat symmetric hash
over only the protocol, addresses and ports. This hash does not get
installed into and override the normal skb hash, so this change has
no effect whatsoever on the rest of the stack.
Reported-by: Eric Leblond <eric@regit.org>
Tested-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since bpf_prog_get() and program type check is used in a couple of places,
refactor this into a small helper function that we can make use of. Since
the non RO prog->aux part is not used in performance critical paths and a
program destruction via RCU is rather very unlikley when doing the put, we
shouldn't have an issue just doing the bpf_prog_get() + prog->type != type
check, but actually not taking the ref at all (due to being in fdget() /
fdput() section of the bpf fd) is even cleaner and makes the diff smaller
as well, so just go for that. Callsites are changed to make use of the new
helper where possible.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new event - NETDEV_CHANGE_TX_QUEUE_LEN, this
will be triggered when tx_queue_len. It could be used by net device
who want to do some processing at that time. An example is tun who may
want to resize tx array when tx_queue_len is changed.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding rule with NLM_F_EXCL flag then check if the same rule exist.
If yes then exit with -EEXIST.
This is already implemented in iproute2:
if (cmd == RTM_NEWRULE) {
req.n.nlmsg_flags |= NLM_F_CREATE|NLM_F_EXCL;
req.r.rtm_type = RTN_UNICAST;
}
Tested ipv4 and ipv6 with net-next linux on qemu x86
expected behavior after patch:
localhost ~ # ip rule
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
RTNETLINK answers: File exists
localhost ~ # ip rule
0: from all lookup local
1005: from 10.46.177.97 lookup 104
32766: from all lookup main
32767: from all lookup default
There was already topic regarding this but I don't see any changes
merged and problem still occurs.
https://lkml.kernel.org/r/1135778809.5944.7.camel+%28%29+localhost+%21+localdomain
Signed-off-by: Mateusz Bajorski <mateusz.bajorski@nokia.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the IFLA_STATS_LINK_XSTATS_SLAVE attribute
which allows to export per-slave statistics if the master device supports
the linkxstats callback. The attribute is passed down to the linkxstats
callback and it is up to the callback user to use it (an example has been
added to the only current user - the bridge). This allows us to query only
specific slaves of master devices like bridge ports and export only what
we're interested in instead of having to dump all ports and searching only
for a single one. This will be used to export per-port IGMP/MLD stats and
also per-port vlan stats in the future, possibly other statistics as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a helper for changing skb->pkt_type in a controlled way.
We only allow a subset of possible values and can extend that in future
should other use cases come up. Doing this as a helper has the advantage
that errors can be handeled gracefully and thus helper kept extensible.
It's a write counterpart to pkt_type member we can already read from
struct __sk_buff context. Major use case is to change incoming skbs to
PACKET_HOST in a programmatic way instead of having to recirculate via
redirect(..., BPF_F_INGRESS), for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a minimal helper for doing the groundwork of changing
the skb->protocol in a controlled way. Currently supported is v4 to
v6 and vice versa transitions, which allows f.e. for a minimal, static
nat64 implementation where applications in containers that still
require IPv4 can be transparently operated in an IPv6-only environment.
For example, host facing veth of the container can transparently do
the transitions in a programmatic way with the help of clsact qdisc
and cls_bpf.
Idea is to separate concerns for keeping complexity of the helper
lower, which means that the programs utilize bpf_skb_change_proto(),
bpf_skb_store_bytes() and bpf_lX_csum_replace() to get the job done,
instead of doing everything in a single helper (and thus partially
duplicating helper functionality). Also, bpf_skb_change_proto()
shouldn't need to deal with raw packet data as this is done by other
helpers.
bpf_skb_proto_6_to_4() and bpf_skb_proto_4_to_6() unclone the skb to
operate on a private one, push or pop additionally required header
space and migrate the gso/gro meta data from the shared info. We do
mark the gso type as dodgy so that headers are checked and segs
recalculated by the gso/gro engine. The gso_size target is adapted
as well. The flags argument added is currently reserved and can be
used for future extensions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use smp_processor_id() for the generic helper bpf_get_smp_processor_id()
instead of the raw variant. This allows for preemption checks when we
have DEBUG_PREEMPT, and otherwise uses the raw variant anyway. We only
need to keep the raw variant for socket filters, but we can reuse the
helper that is already there from cBPF side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.
More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.
When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.
This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.
Fixes: 4fd3d7d9e8 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing before the open parenthesis '(', and this
will introduce much more noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qdisc performance suffers when packets are dropped at enqueue()
time because drops (kfree_skb()) are done while qdisc lock is held,
delaying a dequeue() draining the queue.
Nominal throughput can be reduced by 50 % when this happens,
at a time we would like the dequeue() to proceed as fast as possible.
Even FQ is vulnerable to this problem, while one of FQ goals was
to provide some flow isolation.
This patch adds a 'struct sk_buff **to_free' parameter to all
qdisc->enqueue(), and in qdisc_drop() helper.
I measured a performance increase of up to 12 %, but this patch
is a prereq so that future batches in enqueue() can fly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing after ',', and this will introduce much more
noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the checkpatch.pl error to dev.c:
ERROR: do not initialise statics to 0
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ctx structure passed into bpf programs is different depending on bpf
program type. The verifier incorrectly marked ctx->data and ctx->data_end
access based on ctx offset only. That caused loads in tracing programs
int bpf_prog(struct pt_regs *ctx) { .. ctx->ax .. }
to be incorrectly marked as PTR_TO_PACKET which later caused verifier
to reject the program that was actually valid in tracing context.
Fix this by doing program type specific matching of ctx offsets.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Reported-by: Sasha Goldshtein <goldshtn@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc are changed under RTNL protection and often
while blocking BH and root qdisc spinlock.
When lots of skbs need to be dropped, we free
them under these locks causing TX/RX freezes,
and more generally latency spikes.
This commit adds rtnl_kfree_skbs(), used to queue
skbs for deferred freeing.
Actual freeing happens right after RTNL is released,
with appropriate scheduling points.
rtnl_qdisc_drop() can also be used in place
of disc_drop() when RTNL is held.
qdisc_reset_queue() and __qdisc_reset_queue() get
the new behavior, so standard qdiscs like pfifo, pfifo_fast...
have their ->reset() method automatically handled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sch_atm returns this when TC_ACT_SHOT classification occurs.
But all other schedulers that use tc_classify
(htb, hfsc, drr, fq_codel ...) return NET_XMIT_SUCCESS | __BYPASS
in this case so just do that in atm.
BATMAN uses it as an intermediate return value to signal
forwarding vs. buffering, but it did not return POLICED to
callers outside of BATMAN.
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always mixed in the parent pointer into the dentry name hash, but we
did it late at lookup time. It turns out that we can simplify that
lookup-time action by salting the hash with the parent pointer early
instead of late.
A few other users of our string hashes also wanted to mix in their own
pointers into the hash, and those are updated to use the same mechanism.
Hash users that don't have any particular initial salt can just use the
NULL pointer as a no-salt.
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a bpf_check_basics_ok() and reject filters that are of invalid
size much earlier, so we don't do any useless work such as invoking
bpf_prog_alloc(). Currently, rejection happens in bpf_check_classic()
only, but it's really unnecessarily late and they should be rejected
at earliest point. While at it, also clean up one bpf_prog_size() to
make it consistent with the remaining invocations.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect the stack's xmit_recursion limit for calls into dev_queue_xmit().
Currently, they are not handeled by the limiter when attached to clsact's
egress parent, for example, and a buggy program redirecting it to the
same device again could run into stack overflow eventually. It would be
good if we could notify an admin to give him a chance to react. We reuse
xmit_recursion instead of having one private to eBPF, so that the stack's
current recursion depth will be taken into account as well. Follow-up to
commit 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper") and
27b29f6305 ("bpf: add bpf_redirect() helper").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This patch introduces a new rule attribute l3mdev. The l3mdev rule
means the table id used for the lookup is pulled from the L3 master
device (e.g., VRF) rather than being statically defined. With the
l3mdev rule all of the basic VRF FIB rules are reduced to 1 l3mdev
rule per address family (IPv4 and IPv6).
If an admin wishes to insert higher priority rules for specific VRFs
those rules will co-exist with the l3mdev rule. This capability means
current VRF scripts will co-exist with this new simpler implementation.
Currently, the rules list for both ipv4 and ipv6 look like this:
$ ip ru ls
1000: from all oif vrf1 lookup 1001
1000: from all iif vrf1 lookup 1001
1000: from all oif vrf2 lookup 1002
1000: from all iif vrf2 lookup 1002
1000: from all oif vrf3 lookup 1003
1000: from all iif vrf3 lookup 1003
1000: from all oif vrf4 lookup 1004
1000: from all iif vrf4 lookup 1004
1000: from all oif vrf5 lookup 1005
1000: from all iif vrf5 lookup 1005
1000: from all oif vrf6 lookup 1006
1000: from all iif vrf6 lookup 1006
1000: from all oif vrf7 lookup 1007
1000: from all iif vrf7 lookup 1007
1000: from all oif vrf8 lookup 1008
1000: from all iif vrf8 lookup 1008
...
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
With the l3mdev rule the list is just the following regardless of the
number of VRFs:
$ ip ru ls
1000: from all lookup [l3mdev table]
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
(Note: the above pretty print of the rule is based on an iproute2
prototype. Actual verbage may change)
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make htmldocs" complains otherwise:
.//net/core/gen_stats.c:168: warning: No description found for parameter 'running'
.//include/linux/netdevice.h:1867: warning: No description found for parameter 'qdisc_running_key'
Fixes: f9eb8aea2a ("net_sched: transform qdisc running bit into a seqcount")
Fixes: edb09eb17e ("net: sched: do not acquire qdisc spinlock in qdisc/class stats dump")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make htmldocs" complains otherwise:
.//net/core/gen_stats.c:65: warning: No description found for parameter 'padattr'
.//net/core/gen_stats.c:101: warning: No description found for parameter 'padattr'
Fixes: 9854518ea0 ("sched: align nlattr properly when needed")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in kdump kernel, reduce memory usage by only using a single Queue
Set for multiqueue devices. So make netif_get_num_default_rss_queues()
return one, when in kdump kernel.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_find_net_device_by_node() function is defined in
<linux/of_net.h> but not included in the .c file that
implements it. Fix the following warning by including the
header:
net/core/net-sysfs.c:1494:19: warning: symbol 'of_find_net_device_by_node' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Large tc dumps (tc -s {qdisc|class} sh dev ethX) done by Google BwE host
agent [1] are problematic at scale :
For each qdisc/class found in the dump, we currently lock the root qdisc
spinlock in order to get stats. Sampling stats every 5 seconds from
thousands of HTB classes is a challenge when the root qdisc spinlock is
under high pressure. Not only the dumps take time, they also slow
down the fast path (queue/dequeue packets) by 10 % to 20 % in some cases.
An audit of existing qdiscs showed that sch_fq_codel is the only qdisc
that might need the qdisc lock in fq_codel_dump_stats() and
fq_codel_dump_class_stats()
In v2 of this patch, I now use the Qdisc running seqcount to provide
consistent reads of packets/bytes counters, regardless of 32/64 bit arches.
I also changed rate estimators to use the same infrastructure
so that they no longer need to lock root qdisc lock.
[1]
http://static.googleusercontent.com/media/research.google.com/en//pubs/archive/43838.pdf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Kevin Athey <kda@google.com>
Cc: Xiaotian Pei <xiaotian@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a single bit (__QDISC___STATE_RUNNING)
in sch->__state, use a seqcount.
This adds lockdep support, but more importantly it will allow us
to sample qdisc/class statistics without having to grab qdisc root lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman