bigger updates, the rest is driver updates all over the place
-----BEGIN PGP SIGNATURE-----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=/It5
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Core got a new helper 'i2c_client_get_device_id()', designware got
some bigger updates, the rest is driver updates all over the place"
* tag 'i2c-for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (41 commits)
i2c: ismt: Fix an out-of-bounds bug in ismt_access()
i2c: mux: reg: check return value after calling platform_get_resource()
i2c: xiic: Make sure to disable clock on .remove()
i2c: hisi: Add support to get clock frequency from clock
i2c: pxa-pci: fix missing pci_disable_device() on error in ce4100_i2c_probe
i2c: slave-eeprom: Convert to i2c's .probe_new()
i2c: mux: pca954x: Convert to i2c's .probe_new()
drivers/i2c: use simple i2c probe
i2c: mux: pca9541: switch to using .probe_new
i2c: gpio: Fix potential unused warning for 'i2c_gpio_dt_ids'
i2c: qcom-geni: add support for I2C Master Hub variant
i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant
soc: qcom: geni-se: add support for I2C Master Hub wrapper variant
soc: qcom: geni-se: add desc struct to specify clocks from device match data
dt-bindings: i2c: qcom-geni: document I2C Master Hub serial I2C engine
dt-bindings: qcom: geni-se: document I2C Master Hub wrapper variant
dt-bindings: i2c: renesas,riic: Document RZ/Five SoC
i2c: tegra: Set ACPI node as primary fwnode
i2c: smbus: add DDR support for SPD
i2c: /pasemi: PASemi I2C controller IRQ enablement
...
Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.
This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.
Fixes: 4544b9f25e ("dma-mapping: Add vmap checks to dma_map_single()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
pm_runtime_get_sync() returning 1 also means the device is powered. So
resetting the chip registers in .remove() is possible and should be
done.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d98bdd3a5b ("i2c: imx: Make sure to unregister adapter on remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If for whatever reasons pm_runtime_resume_and_get() fails and .remove() is
exited early, the i2c adapter stays around and the irq still calls its
handler, while the driver data and the register mapping go away. So if
later the i2c adapter is accessed or the irq triggers this results in
havoc accessing freed memory and unmapped registers.
So unregister the software resources even if resume failed, and only skip
the hardware access in that case.
Fixes: 588eb93ea4 ("i2c: imx: add runtime pm support to improve the performance")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
to provid --> to provide
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i.MX8MP Mask Set Errata for Mask 1P33A, Rev. 2.0 has description of
errata ERR007805 as below. This errata is found on all MX8M{M,N,P,Q},
MX7{S,D}, MX6{UL{,L,Z},S{,LL,X},S,D,DL,Q,DP,QP} . MX7ULP, MX8Q, MX8X
are not affected. MX53 and older status is unknown, as the errata
first appears in MX6 errata sheets from 2016 and the latest errata
sheet for MX53 is from 2015. Older SoC errata sheets predate the
MX53 errata sheet. MX8ULP and MX9 status is unknown as the errata
sheet is not available yet.
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
Implement the workaround by matching on the affected SoC specific
compatible strings and by limiting the maximum bus frequency in case
the SoC is affected.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-i2c@vger.kernel.org
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Most IMX I2C interfaces don't generate an interrupt on a stop condition,
so it won't generate a timely stop event on a slave mode transfer.
Some users, like IPMB, need a timely stop event to work properly.
So, add a timer and add the proper handling to generate a stop event in
slave mode if the interface goes idle.
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the following warnings reported by checkpatch::
drivers/i2c/busses/i2c-imx.c:173: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:175: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:176: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:177: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:455: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:602: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:638: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1170: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1374: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1398: WARNING: Prefer strscpy over strlcpy - see: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
pm_runtime_get_sync() will increment the PM reference count even on
failure. Forgetting to put the reference again will result in a leak.
Replace it with pm_runtime_resume_and_get() to keep the usage counter
balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Weihua <yeweihua4@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In i2c_imx_xfer() and i2c_imx_remove(), the pm reference count
is not expected to be incremented on return.
However, pm_runtime_get_sync will increment pm reference count
even failed. Forgetting to putting operation will result in a
reference leak here.
Replace it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 3a5ee18d2a ("i2c: imx: implement master_xfer_atomic callback")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Only the Layerscape SoCs have interrupts on bus idle, which facilitate
sending events which complete slave bus transactions.
Add support for synthesizing missing events. If we see a master request,
or a newly addressed slave request, if the last event sent to the backend
was I2C_SLAVE_READ_REQUESTED, send the backend a I2C_SLAVE_READ_PROCESSED
followed by I2C_SLAVE_STOP. For all other events, send an I2C_SLAVE_STOP.
Signed-off-by: Kevin Paul Herbert <kph@platinasystems.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If interrupt comes late, during probe error path or device remove (could
be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
i2c_imx_isr() will access registers with the clock being disabled. This
leads to external abort on non-linefetch on Toradex Colibri VF50 module
(with Vybrid VF5xx):
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8882d003
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.7.0 #607
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(i2c_imx_isr) from [<8017009c>] (free_irq+0x25c/0x3b0)
(free_irq) from [<805844ec>] (release_nodes+0x178/0x284)
(release_nodes) from [<80580030>] (really_probe+0x10c/0x348)
(really_probe) from [<80580380>] (driver_probe_device+0x60/0x170)
(driver_probe_device) from [<80580630>] (device_driver_attach+0x58/0x60)
(device_driver_attach) from [<805806bc>] (__driver_attach+0x84/0xc0)
(__driver_attach) from [<8057e228>] (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from [<8057f3ec>] (bus_add_driver+0x144/0x1ec)
(bus_add_driver) from [<80581320>] (driver_register+0x78/0x110)
(driver_register) from [<8010213c>] (do_one_initcall+0xa8/0x2f4)
(do_one_initcall) from [<80c0100c>] (kernel_init_freeable+0x178/0x1dc)
(kernel_init_freeable) from [<80807048>] (kernel_init+0x8/0x110)
(kernel_init) from [<80100114>] (ret_from_fork+0x14/0x20)
Additionally, the i2c_imx_isr() could wake up the wait queue
(imx_i2c_struct->queue) before its initialization happens.
The resource-managed framework should not be used for interrupt handling,
because the resource will be released too late - after disabling clocks.
The interrupt handler is not prepared for such case.
Fixes: 1c4b6c3bcf ("i2c: imx: implement bus recovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We don't need dev_err() message because when something goes wrong,
platform_get_irq() has print an error message itself, so we should
remove duplicate dev_err().
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rework the read and write code paths in the driver to support operation
in atomic contexts. To achieve this, the driver must not rely on IRQs
and not call schedule(), e.g. via a sleep routine, in these cases.
With this patch the driver supports normal operation, DMA transfers and
now the polling mode or also called sleep-free or IRQ-less operation. It
makes the code not simpler or easier to read, but atomic I2C transfers
are needed on some hardware configurations, e.g. to trigger reboots on
an external PMIC chip.
Signed-off-by: Stefan Lengfeld <contact@stefanchrist.eu>
[m.felsch@pengutronix.de: integrate https://patchwork.ozlabs.org/patch/1085943/ review feedback]
[m.felsch@pengutronix.de: adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
Since commit e1ab9a468e ("i2c: imx: improve the error handling in
i2c_imx_dma_request()") when booting with the DMA driver as module (such
as CONFIG_FSL_EDMA=m) the following endless clk warnings are seen:
[ 153.077831] ------------[ cut here ]------------
[ 153.082528] WARNING: CPU: 0 PID: 15 at drivers/clk/clk.c:924 clk_core_disable_lock+0x18/0x24
[ 153.093077] i2c0 already disabled
[ 153.096416] Modules linked in:
[ 153.099521] CPU: 0 PID: 15 Comm: kworker/0:1 Tainted: G W 5.2.0+ #321
[ 153.107290] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[ 153.113772] Workqueue: events deferred_probe_work_func
[ 153.118979] [<c0019560>] (unwind_backtrace) from [<c0014734>] (show_stack+0x10/0x14)
[ 153.126778] [<c0014734>] (show_stack) from [<c083f8dc>] (dump_stack+0x9c/0xd4)
[ 153.134051] [<c083f8dc>] (dump_stack) from [<c0031154>] (__warn+0xf8/0x124)
[ 153.141056] [<c0031154>] (__warn) from [<c0031248>] (warn_slowpath_fmt+0x38/0x48)
[ 153.148580] [<c0031248>] (warn_slowpath_fmt) from [<c040fde0>] (clk_core_disable_lock+0x18/0x24)
[ 153.157413] [<c040fde0>] (clk_core_disable_lock) from [<c058f520>] (i2c_imx_probe+0x554/0x6ec)
[ 153.166076] [<c058f520>] (i2c_imx_probe) from [<c04b9178>] (platform_drv_probe+0x48/0x98)
[ 153.174297] [<c04b9178>] (platform_drv_probe) from [<c04b7298>] (really_probe+0x1d8/0x2c0)
[ 153.182605] [<c04b7298>] (really_probe) from [<c04b7554>] (driver_probe_device+0x5c/0x174)
[ 153.190909] [<c04b7554>] (driver_probe_device) from [<c04b58c8>] (bus_for_each_drv+0x44/0x8c)
[ 153.199480] [<c04b58c8>] (bus_for_each_drv) from [<c04b746c>] (__device_attach+0xa0/0x108)
[ 153.207782] [<c04b746c>] (__device_attach) from [<c04b65a4>] (bus_probe_device+0x88/0x90)
[ 153.215999] [<c04b65a4>] (bus_probe_device) from [<c04b6a04>] (deferred_probe_work_func+0x60/0x90)
[ 153.225003] [<c04b6a04>] (deferred_probe_work_func) from [<c004f190>] (process_one_work+0x204/0x634)
[ 153.234178] [<c004f190>] (process_one_work) from [<c004f618>] (worker_thread+0x20/0x484)
[ 153.242315] [<c004f618>] (worker_thread) from [<c0055c2c>] (kthread+0x118/0x150)
[ 153.249758] [<c0055c2c>] (kthread) from [<c00090b4>] (ret_from_fork+0x14/0x20)
[ 153.257006] Exception stack(0xdde43fb0 to 0xdde43ff8)
[ 153.262095] 3fa0: 00000000 00000000 00000000 00000000
[ 153.270306] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 153.278520] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 153.285159] irq event stamp: 3323022
[ 153.288787] hardirqs last enabled at (3323021): [<c0861c4c>] _raw_spin_unlock_irq+0x24/0x2c
[ 153.297261] hardirqs last disabled at (3323022): [<c040d7a0>] clk_enable_lock+0x10/0x124
[ 153.305392] softirqs last enabled at (3322092): [<c000a504>] __do_softirq+0x344/0x540
[ 153.313352] softirqs last disabled at (3322081): [<c00385c0>] irq_exit+0x10c/0x128
[ 153.320946] ---[ end trace a506731ccd9bd703 ]---
This endless clk warnings behaviour is well explained by Andrey Smirnov:
"Allocating DMA after registering I2C adapter can lead to infinite
probing loop, for example, consider the following scenario:
1. i2c_imx_probe() is called and successfully registers an I2C
adapter via i2c_add_numbered_adapter()
2. As a part of i2c_add_numbered_adapter() new I2C slave devices
are added from DT which results in a call to
driver_deferred_probe_trigger()
3. i2c_imx_probe() continues and calls i2c_imx_dma_request() which
due to lack of proper DMA driver returns -EPROBE_DEFER
4. i2c_imx_probe() fails, removes I2C adapter and returns
-EPROBE_DEFER, which places it into deferred probe list
5. Deferred probe work triggered in #2 above kicks in and calls
i2c_imx_probe() again thus bringing us to step #1"
So revert commit e1ab9a468e ("i2c: imx: improve the error handling in
i2c_imx_dma_request()") and restore the old behaviour, in order to
avoid regressions on existing setups.
Cc: <stable@vger.kernel.org>
Reported-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: e1ab9a468e ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use __maybe_unused for runtime PM related functions instead
of #if CONFIG_PM to simply the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to free the i2c adapter on the error exit path.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: e1ab9a468e ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Change the call to PTR_ERR to access the value just tested by IS_ERR.
Fixes: 5b3a23a3cc ("i2c: imx: notify about real errors on dma i2c_imx_dma_request")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Improve the error handling in i2c_imx_dma_request() and let it return an error
indication that the caller then can handle accordingly.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least on i.MX5x, the DMA events for I2C and SDHC use the same channel
and there can only be a single user. So in this case there should be no
message emitted that looks like an error if the I2C device doesn't have
an assigned DMA channel. In contrast real problems that were only
emitted at debug level before should be described at a higher level
to be better visible and so understandable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Probe deferral is a normal operating condition in the probe function,
so don't spam the log with an error in this case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
Always update the stopped state when busy status have been checked.
This is identical to what was done before, with the exception of error
handling.
Without this change, some errors cause the stopped state to be left in
incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and
i2c_imx_xfer().
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
I2C is open drain, so request the GPIO accordingly, even if pinmux did
set it up correctly for in-kernel users in this case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to call reinit_completion() before dma is started to avoid race
condition where reinit_completion() is called after complete() and before
wait_for_completion_timeout().
Signed-off-by: Esben Haabendal <eha@deif.com>
Fixes: ce1a78840f ("i2c: imx: add DMA support for freescale i2c driver")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Because it looks neater.
For diolan, this allows factoring out some code that is now common
between if and else.
For eg20t, pch_i2c_writebytes is always called with a write in
msgs->flags, and pch_i2c_readbytes with a read.
For imx, i2c_imx_dma_write and i2c_imx_write are always called with a
write in msgs->flags, and i2c_imx_read with a read.
For qup, qup_i2c_write_tx_fifo_v1 is always called with a write in
qup->msg->flags.
For stu300, also restructure debug output for resends, since that
code as a result is only handling debug output.
Reviewed-by: Guenter Roeck <linux@roeck-us.net> [diolan]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [efm32 and imx]
Acked-by: Linus Walleij <linus.walleij@linaro.org> [stu300]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is unsafe, as the runtime PM callbacks are called from the PM
workqueue, so this may deadlock when handling an i2c attached clock,
which may already hold the clk_prepare mutex from another context.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of repeatedly calling clk_get_rate for each transfer, register
a clock notifier to update the cached divider value each time the clock
rate actually changes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
<linux/of_gpio.h> is not used in this file, by
<linux/gpio/consumer.h> is.
Someone is just lucky with their implicit includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When converting to GPIOD, the GPIO directions of SCL/SDA have been
swapped. Fix it!
Fixes: ad36a27959 ("i2c: imx: switch to using gpiod for bus recovery gpios")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Change the driver to use the gpio descriptors for the bus recovery
information instead of the deprecated integer interface.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The arguments for SDA and SCL were swapped. Fix it.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds