If the hardware supports RoCE v2, we configure the hardware UDP
port according to the RoCE v2 Annex when mlx4_ib device is added.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to support modify_qp for RoCE v2, we need to set
the gid_type in the QP context.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To tell hardware about a gid with type RoCEv2, software needs a new
modifier to the SET_PORT command: MLX4_SET_PORT_ROCE_ADDR. This can
replace the old method, MLX4_SET_PORT_GID_TABLE, for RoCEv1 gids.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
IB core driver adds a property of type to struct ib_gid_attr.
The mlx4 driver should take that in consideration when modifying or
querying the hardware gid table.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Previously, IPV6_DEFAULT_HOPLIMIT was used as the hop limit value for
RoCE. Fixing that by taking ip4_dst_hoplimit and ip6_dst_hoplimit as
hop limit values.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rdma_addr_find_dmac_by_grh resolves dmac, vlan_id and if_index and
downsteram patch will also add hop_limit as an output parameter,
thus we rename it to rdma_addr_find_l2_eth_by_grh.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Sparse complains about dereference before check. Fixing this by
moving the check before the dereference.
Fixes: 200298326b ('IB/core: Validate route when we init ah')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When write_gid function needs to do a sleep-able operation, it unlocks
table->rwlock and then relocks it. Sparse complains about context
imbalance.
This is safe as write_gid is always called with table->rwlock.
write_gid protects from simultaneous writes to this GID entry
by setting the GID_TABLE_ENTRY_INVALID flag.
Fixes: 9c584f0495 ('IB/core: Change per-entry lock in RoCE GID table to
one lock')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Port number is not part of ClassPortInfo attribute but is
still needed as a parameter when invoking process_mad.
To properly handle this attribute, port_num is added as a
parameter to get_counter_table and get_perf_mad was changed
not to store port_num in the attribute itself when it's
querying the ClassPortInfo attribute.
This handles issue pointed out by Matan Barak <matanb@dev.mellanox.co.il>
Fixes: 145d9c5410 ('IB/core: Display extended counter set if available')
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Detected this by building the IB core with W=1. See also patch
"IB core: Fix ib_sg_to_pages()" (commit 8f5ba10ed4).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Leon Romanovsky <leon.romanovsky@mellanox.com>
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the local workqueue to process mad completions and use the CQ API
instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Stop abusing wr_id and just pass the parameter explicitly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix the following sparse warning:
drivers/infiniband/hw/mlx5/main.c:1061:29: warning: symbol 'pfn' shadows
an earlier one
drivers/infiniband/hw/mlx5/main.c:1030:21: originally declared here
Fixes: d69e3bcf79 ('IB/mlx5: Mmap the HCA's core clock register to user-space')
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In commit dbf727de74 ("IB/core: Use GID table in AH creation and dmac
resolution") we copy source mac to mlx4_ah from the attributes of
gid at ib_ah_attr.grh.sgid_index. Now we can use it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Hop limit value wasn't copied from attributes when ah was created.
This may influence packets for unconnected services to get dropped in
routers when endpoints are not in the same subnet.
Fixes: fa417f7b52 ("IB/mlx4: Add support for IBoE")
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Maximum number of EQE capacity per CQ was mistakenly exposed
as CQE. Fix that.
Fixes: 938fe83c8d ("net/mlx5_core: New device capabilities handling")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The h/w is designed in such a way that, if you do anything IPv6
related, a valid clip entry must be there. So take clip reference
before creating IPv6 listening servers, and then if we fail to
create server, release the clip entry.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit c5dfb000b9 ("iw_cxgb4: Pass qid range to user space driver")
from Dec 11, 2015, leads to the following static checker warning:
drivers/infiniband/hw/cxgb4/device.c:857 c4iw_rdev_open()
warn: variable dereferenced before check 'rdev->status_page'
Also we weren't deallocating ocqp pool in error path when failed to
allocate status page. Fixing it too.
Fixes: c5dfb000b9 ("iw_cxgb4: Pass qid range to user space driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The issue here is that there is a cut and paste bug. When we allocate
cma_dev_group->default_ports_group we use "sizeof(*cma_dev_group->ports)"
instead of "sizeof(*cma_dev_group->default_ports_group)".
We're bumping up against the 80 character limit so I introduced a new
local pointer "ports_group" to get around that.
Fixes: 045959db65 ('IB/cma: Add configfs for rdma_cm')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
nes_reg_phys_mr() returns ERR_PTRs on error. It doesn't return NULL.
This bug has been there for a while, but we recently changed from
calling a function pointer to calling nes_reg_phys_mr() directly so now
Smatch is able to detect the bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current code is problematic when the QP creation and ipoib is used to
support NFS and NFS desires to do IO for paging purposes. In that case, the
GFP_KERNEL allocation in qib_qp.c causes a deadlock in tight memory
situations.
This fix adds support to create queue pair with GFP_NOIO flag for connected
mode only to cleanly fail the create queue pair in those situations.
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Attributed ID was declared as an int while the value should really be big
endian 16.
Fixes: 35c4cbb178 ("IB/core: Create get_perf_mad function in sysfs.c")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issuing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
With this patch we stop using administrative open and close events
injected by be2net driver. These events were used to dispatch PORT_ACTIVE
and PORT_ERROR events to the IB-stack. This patch implements a logic
to receive async-link-events generated from CNA whenever link-state-change
is detected. Now on, these async-events will be used to dispatch
PORT_ACTIVE and PORT_ERROR events to IB-stack.
Depending on async-events from CNA removes the need to hold device-list-mutex
and thus breaks the busy-wait scenario.
Reported-by: Doug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Dispatch only port event to IB stack when port state changes.
Don't explicitly modify qps to error. Let application listen to
port events on async event queue or let QP fail with retry-exceeded
completion error.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
vlan-id is wrongly getting as 0 when PFC is enabled.
Set vlan-id configured by user in QP parameters.
In case vlan interface is not used, flash a warning to
user to configure vlan and assign vlan-id as 0 in qp params.
Fixes: dbf727de74 ('IB/core: Use GID table in AH creation and dmac resolution')
Cc: Matan Barak <matanb@mellanox.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
cma_validate_port wrongly assumed that Ethernet devices are RoCE
devices and thus their ndev should be matched in the GID table.
This broke the iWarp support. Fixing that matching the ndev only if
we work on a RoCE port.
Cc: <stable@vger.kernel.org> # 4.4.x-
Fixes: abae1b71dd ('IB/cma: cma_validate_port should verify the port
and netdevice')
Reported-by: Hariprasad Shenai <hariprasad@chelsio.com>
Tested-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ipoib_mcast_restart_task calls ipoib_mcast_remove_list with the
parameter mcast->dev. That mcast is a temporary (used as an iterator)
variable that may be uninitialized.
There is no need to send the variable dev to the function, as each mcast
has its dev as a member in the mcast struct.
This causes the next panic:
RIP: 0010: ipoib_mcast_leave+0x6d/0xf0 [ib_ipoib]
RSP: 0018: EFLAGS: 00010246
RAX: f0201 RBX: 24e00 RCX: 00000
....
....
Stack:
Call Trace:
ipoib_mcast_remove_list+0x3a/0x70 [ib_ipoib]
ipoib_mcast_restart_task+0x3bb/0x520 [ib_ipoib]
process_one_work+0x164/0x470
worker_thread+0x11d/0x420
...
Fixes: 5a0e81f6f4 ('IB/IPoIB: factor out common multicast list removal code')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reported-by: Doron Tsur <doront@mellanox.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Declare that we support remote invalidation in case we are:
1. using fastreg method
2. always registering memory
Detect the invalidated rkey from the work completion info so we
won't invalidate it locally. The spec mandates that we must not rely
on the target remote invalidate our rkey so we must check it upon
a receive (scsi response) completion.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When we enable remote invalidate support we won't want to perform
local invalidates at the same time we do today, but we still need
to get new rkeys. So, decouple the rkey update from the local
invalidate and tie it to memory reg instead.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We'll use remote invalidate, according to negotiation result
during connection establishment. If the initiator declared that
it supports the remote invalidate exception and the local HCA
supports IB_DEVICE_MEM_MGT_EXTENSIONS then the target will
use IB_WR_SEND_WITH_INV with the correct rkey for the response.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iser target does not support zero based virtual addresses and
send with invalidate, so it should declare that it doesn't.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We don't need iser_proto.h anymore, remove it and
move (non-protocol) declarations to ib_isert.h
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The iser RDMA_CM negotiation protocol is shared by
the initiator and the target, so have a shared header
for the defines and structure. Move relevant items from
the initiator and target headers.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This parameter is described as "is mr valid indicator".
In other words, it indicates whether memory registration
is valid or not. So intuitive values would be:
mr_valid=True, when memory registration is valid and
mr_valid=False otherwise.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When all the task data is sent as immediate data, we are
allowed to use the local_dma_lkey as it is not sent to
the wire.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We have in iser iser_sg_to_page_vec which has exactly
the same role as ib_sg_to_pages. Customize the page_vec
to hold a fake MR so we can reuse ib_sg_to_pages.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Destroy workqueue on transport register error, also
release kmem cache on workqueue allocation error.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This mmu_notifier_ops structure is never modified, so declare it as
const, like the other mmu_notifier_ops structures.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The iser_reg_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The nes_cm_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch will report the tx/rx checksum cap for raw qp via the
query device results.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Failure in kmalloc memory allocations will throw a warning about it.
Such warnings are not needed anymore, since in commit 0ef2f05c7e
("IB/mlx4: Use vmalloc for WR buffers when needed"), fallback mechanism
from kmalloc() to __vmalloc() was added.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to ensure IB spec atomic correctness in atomic operations, if
HW is configured to host endianness, advertise IB_ATOMIC_HCA. if not,
advertise IB_ATOMIC_NONE.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Moni Shoua