This patch adds support for TPS65218 PMIC regulators.
The regulators set consists of 6 DCDCs and 1 LDO. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
MAX14577 chip is a multi-function device which includes MUIC,
charger and voltage regulator. The driver is located in drivers/mfd.
This patch adds regulator driver for MAX14577 chip. There are two
regulators in this chip:
1. Safeout LDO with constant voltage output of 4.9V. It can be only
enabled or disabled.
2. Current regulator for the charger. It provides current from 90mA up
to 950mA.
Driver supports Device Tree.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The AMS AS3722 is a compact system PMU suitable for mobile phones,
tablets etc. It has 4 DCDC step down regulators, 3 DCDC step down
controller, 11 LDOs.
Add a driver to support accessing the DCDC/LDOs found on the AMS
AS3722 PMIC using regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Florian Lobmaier <florian.lobmaier@ams.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ST Microelectronics STw481x PMIC used for the Nomadik
has one single software-controlled regulator for VMMC.
This driver registers directly to the compatible string
as there is just one regulator.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cut down on the size of core.c a bit more and ensure that the devres
versions of things don't do too much peering inside the internals of
the APIs they wrap.
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver adds support for the following DA9063 PMIC regulators:
- 11x LDOs (named LDO1 - LDO11),
- 6x buck converters (BCORE1, BCORE2, BPRO, BMEM, BIO, BPERI),
Regulators provide following operations:
- REGULATOR_CHANGE_STATUS and REGULATOR_CHANGE_VOLTAGE for all regulators,
- REGULATOR_CHANGE_MODE for LDOs and buck converters, where:
- LDOs allow REGULATOR_MODE_NORMAL and REGULATOR_MODE_STANDBY,
- buck converters allow REGULATOR_MODE_FAST, REGULATOR_MODE_NORMAL
and REGULATOR_MODE_STANDBY,
- REGULATOR_CHANGE_CURRENT for buck converters (current limits).
The driver generates REGULATOR_EVENT_OVER_CURRENT for LDO3, LDO4, LDO7, LDO8
and LDO11.
Internally, PMIC provides two voltage configurations for normal and suspend
system state for each regulator. The driver switches between those on
suspend/wake-up to provide quick and fluent output voltage change.
This driver requires MFD core driver for operation.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
I2C driver for the Dialog DA9210 Multi-phase 12A DC-DC Buck.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add pfuze100 regulator driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the regulator driver for PMIC 88pm800 including device tree
support.
88pm800 is an I2C-based power-management IC containing voltage
regulators, a real-time clock, and some general purpose ADC devices,
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds new regulator driver to support max77693 chip's regulators.
max77693 has two linear voltage regulators and one current regulator which
can be controlled through I2C bus. This driver also supports device tree.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch changes the order in which the AB8500 regulator drivers are
registered and subsequently probed. It saves a lot of -EPROBE_DEFEER
nonsense and bootlog noise, as some AB8500 core regulators depend on
the external ones for supply voltage.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Texas Instruments' SmartReflex 2 technology provides support for this
power management technique with Forward Body Biasing (FBB) and Reverse
Body Biasing (RBB). These modulate the body voltage of transistor
cells or blocks dynamically to gain performance and reduce leakage.
TI's SmartReflex white paper[1] has further information for usage in
conjunction with other power management techniques.
The application of FBB/RBB technique is determined for each unique
device in some process nodes, whereas, they are mandated on other
process nodes.
In a nutshell, ABB technique is implemented on TI SoC as an on-chip
LDO which has ABB module controlling the bias voltage. However, the
voltage is unique per device. These vary per SoC family and the manner
in which these techniques are used may vary depending on the Operating
Performance Point (OPP) voltage targeted. For example:
OMAP3630/OMAP4430: certain OPPs mandate usage of FBB independent of
devices.
OMAP4460/OMAP4470: certain OPPs mandate usage of FBB, while others may
optionally use FBB or optimization with RBB.
OMAP5: ALL OPPs may optionally use ABB, and ABB biasing voltage is
influenced by vset fused in s/w and requiring s/w override of
default values.
Further, two generations of ABB module are used in various TI SoCs.
They have remained mostly register field compatible, however the
register offset had switched between versions.
We introduce ABB LDO support in the form of a regulator which is
controlled by voltages denoting the desired Operating Performance
Point which is targeted. However, since ABB transition is part of OPP
change sequence, the sequencing required to ensure sane operation
w.r.t OPP change is left to the controlling driver (example: cpufreq
SoC driver) using standard regulator operations.
The driver supports all ABB modes and ability to override ABB LDO vset
control efuse based ABB mode detection etc.
Current implementation is heavily influenced by the original patch
series [2][3] from Mike Turquette. However, the current implementation
supports only device tree based information.
[1] http://www.ti.com/pdfs/wtbu/smartreflex_whitepaper.pdf
[2] http://marc.info/?l=linux-omap&m=134931341818379&w=2
[3] http://marc.info/?l=linux-arm-kernel&m=134931402406853&w=2
[nm@ti.com: co-developer]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ABx500 is capable of controlling three external regulator supplies.
Most commonly on and off are supported, but if an external regulator
chipset or power supply supports high-power and low-power mode settings,
we can control those too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is for new lp8755 regulator dirver and
several unsed variables were deleted and then test was done.
LP8755 :
The LP8755 is a high performance power management unit.It contains
six step-down DC-DC converters which can can be filexibly bundled
together in multiphase converters as required by application.
www.ti.com
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver supports the 4 DCDC and 8 LDO regulators on the AS3711 PMIC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.
Add regulator driver for this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the Regulator patch for the DA9055 PMIC and has got dependency on
the DA9055 MFD core.
This patch support all of the DA9055 regulators. The output voltages are
fully programmable through I2C interface only. The platform data with regulation
constraints is passed down from the board to the regulator.
This patch is functionaly tested on SMDK6410 board. DA9055 Evaluation board
was connected to the SMDK6410 board.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add regulator driver for Texas Instrument TPS80031/TPS80032 device.
TPS80031/ TPS80032 Fully Integrated Power Management with Power
Path and Battery Charger. It has 5 configurable step-down
converters, 11 general purpose LDOs, VBUS generator and digital
output to control regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implementation of the regulator framework driver for the
Versatile Express voltage control. Devices without
voltage constraints (ie. "regulator-[min|max]-microvolt"
properties in the DT node) are treated as fixed (or rather
read-only) regulators.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TPS51632 is a driverless step down controller with
serial control. Advanced features such as D-Cap+
architecture with overlapping pulse support and OSR
overshoot reduction provide fast transient response,
lowest output capacitance and high efficiency.
The TPS51632 supports both I2C and DVFS interfaces
(through PWM) for dynamic control of the output voltage
and current monitor telemetry.
Add regulator driver for TPS51632.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver supports Fairchild FAN53555 Digitally Programmable
TinyBuck Regulator. The FAN53555 is a step-down switching voltage
regulator that delivers a digitally programmable output from an
input voltage supply of 2.5V to 5.5V. The output voltage is
programmed through an I2C interface.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Allowed probing from device tree.
* Reworked the regulator driver to be represented as a single device that
provides multiple regulators, rather than as a device per regulator.
* Replaced many regulator ops with standard functions.
* Added ability to specify supplies for each regulator.
* Removed the WLED regulator. If/when we expose this in the driver, it
should be a backlight object not a regulator object.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TI LP8788 PMU has 4 BUCKS and 22 LDOs.
The voltage of BUCK1 and BUCK2 can be controlled by external gpios.
And some LDOs also can be enabled by external gpios.
The regmap interface is used for regulator operations.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add Samsung S2MPS11 regulator driver.
The S2MPS11 can support 10 Bucks and 38 LDOs and RTC.
Especially, S2MPS11 is designed for high performance
Samsung application processor.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Arizona class devices feature an integrated LDO which is intended to
supply the digital core for the device. Provide a driver offering
minimal control of this regulator.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona platform is used for a range of low power audio hub
CODECs. Many of these devices feature an integrated power supply for the
microphone which is supported by this driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver supports TI/National LP8720, LP8725 PMIC.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add driver for support max77686 regulator.
MAX77686 provides LDOs[1~26] and BUCKs[1~9]. It support to set or get the
volatege of regulator on max77686 chip with using regmap.
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the Kconfig/Makefile stuff for the palmas regulator driver
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The RC5T583 PMIC from RICOH consists of 4 DCDC and 10
LDOs. This driver supports the control of different
regulator output through regulator interface.
This driver depends on MFD driver of RC5T583 and uses
mfd rc5t583 apis to communicate to device for accessing
different device's registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add TPS65090 regulator driver
TPS65090 PMIC from TI consists of 3 step down converters,
2 always on LDOs and 7 current limited load switches. The
output voltages are ON/OFF controllable and are meant to
supply power to the components on target board.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The pxa regulator branch removes the bq24022 driver, while a lot of
other regulator drivers got added in the regulator tree. This
resolves the trivial conflicts by merging in the regulator patches
that are already merged into v3.4.
Conflicts:
drivers/regulator/Kconfig
drivers/regulator/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Anatop is an integrated regulator inside i.MX6 SoC.
There are 3 digital regulators which controls PU, CORE (ARM), and SOC.
And 3 analog regulators which controls 1P1, 2P5, 3P0 (USB).
This patch adds the Anatop regulator driver.
Signed-off-by: Nancy Chen <Nancy.Chen@freescale.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sort Kconfig entries by company name/driver in alphabetical order.
Sort Makefile entries by alphabetical order.
In order to group all the Kconfig entries by company name,
this patch also adds company name to some Kconfig entries.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bq24022 driver is just a specialised form of a gpio-regulator.
As all former users of it now use the gpio-regulator directly, there
is no need to keep it around.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Some devices require a regulator to work, but boards may not have
a software controllable regulator for this device. Provide a helper
function to make it simpler for these boards to register a fixed
regulator as a dummy regulator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds tps65217 PMIC as a regulator
The regulator module consists of 3 DCDCs and 4 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add Samsung S5M8767A pmic configuration.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As we progress with DB5500 and future voltage domain regulators
based on very similar hardware as found in the DB8500 PRCMU,
it makes sense to split off the generic parts and introduce
some generic debug code for the DBx500 regulators. This patch
accoplish a basic abstraction of the DBx500 voltage domain
regulators.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulator module consists of 1 DCDC. The output voltage
is configurable and is meant for supply power to the core
voltage of Soc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Dialog PMIC has below featured regulators:-
DA9052-BC - 4 DVS Buck converters 0.5V - 3.6V upto 1Amp.
DA9053-AA/BX - 4 DVS Buck converters 0.5V - 2.5V upto 3Amp.
DA9052/53 - 10 Programmable LDO's High PSSR, 1% accuracy.
This patch support all the DA9052 and Da9053 regulators. The output voltages are
fully programmable via I2C or SPI interface. The platform data with regulation
constraints is passed down from the board to the regulator.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The helper routine is meant to be used by the regulator drivers
to extract the regulator_init_data structure from the data
that is passed from device tree.
'consumer_supplies' which is part of regulator_init_data is not extracted
as the regulator consumer mappings are passed through DT differently,
implemented in subsequent patches.
Similarly the regulator<-->parent/supply mapping is handled in
subsequent patches.
Also add documentation for regulator bindings to be used to pass
regulator_init_data struct information from device tree.
Some of the regulator properties which are linux and board specific,
are left out since its not clear if they can
be in someway embedded into the kernel or passed in from DT.
They will be revisited later.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add regulator driver for AnalogicTech AAT2870.
Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The tps65912 consist of 4 DCDCs and 10 LDOs. The output voltages can be
configured by the SPI or I2C interface, they are meant to supply power
to the main processor and other components.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The regulator module consists of 3 DCDCs and 8 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The DB8500 has ePOD:s (electronic power domains) which are possible
to switch on/off to deactivate silicon blocks on the DB8500 SoC
by cutting their power without retention. We model these as simple
regulators with one bit on/off settings.
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
move some common functions and micros of mc13783 regulaor driver to
a seperate file, which makes it possible for mc13892 to share code.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TPS6524X provides three step-down converters and two general-purpose LDO
voltage regulators. This device is interfaced using SPI.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow machine drivers to explicitly enable the use of the dummy regulator,
enabling simpler support for systems with only a few specific supplies
visible to software.
It is strongly recommended that this is not used on systems with
substantial software control over their PMICs, for maximum functionality
constrints should be as fully specified as possible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.
If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.
We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
- Style correction
- Can accept platform_data with invalid GPIOs
- Removed unnecessary features
- Improved error handling
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Hi Mark,
> I think that's everything.
Please find the updated patch set as below.
>From f4bf7eec4d210db5075c0bce4521d9be6bc76c8c Mon Sep 17 00:00:00 2001
From: Sundar R Iyer <sundar.iyer@stericsson.com>
Date: Sun, 6 Jun 2010 19:12:12 +0530
Subject: [PATCH v3 1/2] regulator: add support for regulators on the ab8500 MFD
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voltage regulator driver for Maxim 8998 chip. This chip
is used on Samsung Aquila and GONI boards and provides following
functionalities:
- 4 BUCK voltage converters, 17 LDO power regulators and 5 other power
controllers
- battery charger
This patch adds basic driver for voltage regulators and MAX 8998 MFD core.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This device is very simple, it supports one buck and two LDOs. The LDOs are
fixed-voltage. Only the buck is programable over the I2C bus to 16 possible
voltages.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The AD5398 and AD5821 are single 10-bit DAC with 120 mA output current
sink capability. They feature an internal reference and operates from
a single 2.7 V to 5.5 V supply.
This driver supports both the AD5398 and the AD5821. It adapts into the
voltage and current framework.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8925 contains 3 Buck and 20 LDO regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to ease transitions with drivers are boards start using regulators
provide an option to cause all regulator_get() calls to succeed, with a
dummy always on regulator being supplied where one has not been configured.
A warning is printed whenever the dummy regulator is used to aid system
development.
This regulator does not implement any regulator operations but will allow
simple consumers which only do enable() and disable() calls to run. It
is kept separate from the fixed voltage regulator to avoid Kconfig
confusion on the part of users when it is extended to allow boards to
explicitly use the dummy regulator to simplify cases where the majority
of supplies are from fixed regulators without software control.
This option is currently only effective for systems which do not specify
full constriants. If required an override could also be provided to allow
these systems to use the dummy regulator, though it is likely that
unconfigured supplies on such systems will lead to error due to
regulators being powered down more aggressively when not in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8994 contains two LDOs with mixed hardware/software control to
minimise the number of external supplies required while delivering
optimal voltages to minimise power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
One annoying thing about the old name was that the module was just
called mc13783 which caused wrong expectations (at least for me).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Hi Liam,
Since Samuel merged a new version of mfd 88pm8607 driver, I format a
new patch on regulator 88pm8607. I paste the new patch in mail. Please
help to review again. And I also attach the mfd driver in mail.
From: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Thu, 8 Oct 2009 09:36:53 -0400
Subject: [PATCH] regulator: Add 88PM8607 PMIC driver
This patch adds regulator drivers for Marvell 88PM8607 PMIC.
This controller contains 3 DVC and 14 LDO regulators. This controller
uses I2C interface.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tested with a MX25-based custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding TPS65023 and TPS6507x regulator driver support in
drivers/regulator/Makefile and drivers/regulator/Kconfig
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds support for the regulators found in the AB3100
Mixed-Signal IC.
It further also defines platform data for the ST-Ericsson
U300 platform and extends the AB3100 MFD driver so that
platform/board data with regulation constraints and an init
function can be passed down all the way from the board to
the regulators.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides basic support for the voltage regulators
integrated into the Freescale MC13783 PMIC. It is currently
only possible to enable/disable outputs, not to actually
set the voltage.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of PMICs provide two constant current sinks
designed to drive strings of serially connected LEDs for applications
such as backlights. This driver adds support for those regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices provide three types of LDO:
- General purpose LDOs supporting voltages from 0.9-3.3V
- High performance analogue LDOs supporting voltages from 1-3.5V
- Very low power consumption LDOs intended to support always on
functionality.
This patch adds support for all three kinds of LDO. Each regulator
is probed as an individual platform device with resources used to
provide the register map location of the regulator. Mixed hardware
and software control of regulators is not current supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices all have 3 DC-DC buck convertors. This
driver implements software control for these regulators via the
regulator API. Use with split hardware/software control of individual
regulators is not supported, though regulators not controlled by
software may be controlled via the hardware control interfaces.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add (partial) support for the voltage regulators on the PCAP2 PMIC.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.
The chip is controlled through the I2C bus.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Support most of the LDO regulators in the twl4030 family chips.
In the case of LDOs supporting MMC/SD, the voltage controls are
used; but in most other cases, the regulator framework is only
used to enable/disable a supplies, conserving power when a given
voltage rail is not needed.
The drivers/mfd/twl4030-core.c code already sets up the various
regulators according to board-specific configuration, and knows
that some chips don't provide the full set of voltage rails.
The omitted regulators are intended to be under hardware control,
such as during the hardware-mediated system powerup, powerdown,
and suspend states. Unless/until software hooks are known to
be safe, they won't be exported here.
These regulators implement the new get_status() operation, but
can't realistically implement get_mode(); the status output is
effectively the result of a vote, with the relevant hardware
inputs not exposed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Changes from V1:
- Removed support for suspend_enable & suspend_disable functions.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8350 features six DCDC convertors (four buck and two boost), four
LDO voltage regulators and two constant current sinks. This driver adds
support for these through the regulator API.
This driver was written by Liam Girdwood with updates for submission
from Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8400 provides two programmable DCDC step-down (buck) convertors
and four low-dropout (LDO) regulators. This driver provides support for
runtime managment of these in the standard regulator API.
Support for configuration of the suspend and hibernate mode behaviour
of the regulators is not yet included.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds a regulator driver for the TI bq24022 Single-Chip
Li-Ion Charger with its nCE and ISET2 pins connected to GPIOs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This patch adds kernel build support for the regulator core.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Keerthy