In case the SPI thread is not running, a simple reset of sync
state won't fix the transmit timeout. We also need to wake up the kernel
thread.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: ed7d42e24e ("net: qca_spi: fix transmit queue timeout handling")
Signed-off-by: David S. Miller <davem@davemloft.net>
As long as the synchronization with the QCA7000 isn't finished, we
cannot accept packets from the upper layers. So let the SPI thread
enable the TX queue after sync and avoid unwanted packet drop.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the recently introduced helper to replace the pattern of
skb_put() && memset(), this transformation was done with the
following spatch:
@@
identifier p;
expression len;
expression skb;
@@
-p = skb_put(skb, len);
-memset(p, 0, len);
+p = skb_put_zero(skb, len);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately the frame format is not exactly identical between SPI
and UART. In case of SPI there is an additional HW length at the
beginning. So store the initial state to make the decoding state machine
more flexible and easy to extend for UART support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for the upcoming UART driver we need a module
which contains common functions for both interfaces. The module
qca_framing is a good candidate but renaming to qca_7k_common would
make it clear.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this driver is specific to the QCA7000, we should make the module
description more precisely.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function qcaspi_tx_cmd() is only called from qca_spi.c. So we better
move it there.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for an additional MTU define.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid mixing things up, make the MTU and frame length
defines easier to read.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to export qcaspi_netdev_open and qcaspi_netdev_close
because they are also accessible via the net_device_ops.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SET_NETDEV_DEV() in qca_spi to create the "/sys/class/net/<if>/device"
symlink.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca_spi driver causes alignment issues on ARM devices.
So fix this by using netdev_alloc_skb_ip_align().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
a trans_start struct member exists twice:
- in struct net_device (legacy)
- in struct netdev_queue
Instead of open-coding dev->trans_start usage to obtain the current
trans_start value, use dev_trans_start() instead.
This is not exactly the same, as dev_trans_start also considers
the trans_start values of the netdev queues owned by the device
and provides the most recent one.
For legacy devices this doesn't matter as dev_trans_start can cope
with netdev trans_start values of 0 (they are ignored).
This is a prerequisite to eventual removal of dev->trans_start.
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
qca_spi as it modifies the skb on xmit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a tx queue timeout every transmit is blocked until the
QCA7000 resets himself and triggers a sync which makes the driver
flushs the tx ring. So avoid this blocking situation by triggering
the sync immediately after the timeout. Waking the queue doesn't
make sense in this situation.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Registering the netdev before setting the priv data is unsafe.
So fix this possible race by setting the priv data first.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: <stable@vger.kernel.org> # v3.18+
Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
All spi based drivers have an instance of struct spi_device
as spi. This patch renames spi_device to spi to synchronize
with all the drivers.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call ether_setup after alloc_ethdev since it was
already called there.
Follow commits c706471b26 ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbfb3 ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Ethernet over SPI driver for the
Qualcomm QCA7000 HomePlug GreenPHY.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren