The parameter is unused, and complicates a following fix. Just remove
it.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It seems, we're fine with just annotating the two functions.
Thus, this fixes the following build warnings on ppc64:
WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1664):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x6044):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.
WARNING: arch/powerpc/kernel/built-in.o(.text+0x2db30):
The function .start_secondary() references
the function __cpuinit .vdso_getcpu_init().
This is often because .start_secondary lacks a __cpuinit
annotation or the annotation of .vdso_getcpu_init is wrong.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Bestcomm driver requests a memory region larger than the one
described in the device tree. This is due to an extra undocumented field
in the bestcomm register structure. This hasn't been a problem up to
now, but there is a patch pending to make the DT platform_bus support
code use platform_device_add() which tightens the rules and provides
extra checks for drivers to stay within the specified register regions.
Alternately, I could have removed the extra field from the structure,
but I'm not sure if it is still needed for resume to work. Better be
safe and leave it in.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anatolij Gustschin <agust@denx.de>
Fix warnings:
symbol 'clockctl' was not declared. Should it be static?
symbol 'rate_clks' was not declared. Should it be static?
symbol 'dev_clks' was not declared. Should it be static?
symbol 'mpc5121_clk_init' was not declared. Should it be static?
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add ability to configure chip select (CS) parameters for devices
that need different CS parameters setup after their configuration.
I.e. an FPGA device on LP bus can require different CS parameters
for its bus interface after loading firmware into it. A driver
can easily reconfigure the LPC CS parameters using this function.
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The IRQ_PER_CPU Kconfig symbol was removed in the following commit:
Commit 6a58fb3bad ("genirq: Remove
CONFIG_IRQ_PER_CPU") merged in v2.6.39-rc1.
But IRQ_PER_CPU wasn't removed from any of the architecture Kconfig
files where it was defined or selected. It's completely unused so remove
the remaining references.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <uclinux-dist-devel@blackfin.uclinux.org>
Cc: <linux-mips@linux-mips.org>
Cc: <linuxppc-dev@lists.ozlabs.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Link: http://lkml.kernel.org/r/1359972583-17134-1-git-send-email-james.hogan@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ASM version of hash computation function was truncating the upper bit.
Make the ASM version similar to hpt_hash function. Remove masking vsid bits.
Without this patch, we observed hang during bootup due to not satisfying page
fault request correctly. The fault handler used wrong hash values to update
the HPTE. Hence we kept looping with page fault.
hash_page(ea=000001003e260008, access=203, trap=300 ip=3fff91787134 dsisr 42000000
The computed value of hash 000000000f22f390
update: avpnv=4003e46054003e00, hash=000000000722f390, f=80000006, psize: 2 ...
BenH: The over-masking has been there for ever but only hurts with the
new 64T support introduced in 3.7
Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.7]
Only alpha and sparc are unusual - they have ka_restorer in it.
And nobody needs that exposed to userland.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Switch from __ARCH_WANT_SYS_RT_SIGACTION to opposite
(!CONFIG_ODD_RT_SIGACTION); the only two architectures that
need it are alpha and sparc. The reason for use of CONFIG_...
instead of __ARCH_... is that it's needed only kernel-side
and doing it that way avoids a mess with include order on many
architectures.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make some POWER7-specific perf events available in sysfs.
$ /bin/ls -1 /sys/bus/event_source/devices/cpu/events/
branch-instructions
branch-misses
cache-misses
cache-references
cpu-cycles
instructions
PM_BRU_FIN
PM_BRU_MPRED
PM_CMPLU_STALL
PM_CYC
PM_GCT_NOSLOT_CYC
PM_INST_CMPL
PM_LD_MISS_L1
PM_LD_REF_L1
stalled-cycles-backend
stalled-cycles-frontend
where the 'PM_*' events are POWER specific and the others are the
generic events.
This will enable users to specify these events with their symbolic
names rather than with their raw code.
perf stat -e 'cpu/PM_CYC' ...
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062528.GE13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Make the generic perf events in POWER7 available via sysfs.
$ ls /sys/bus/event_source/devices/cpu/events
branch-instructions
branch-misses
cache-misses
cache-references
cpu-cycles
instructions
stalled-cycles-backend
stalled-cycles-frontend
$ cat /sys/bus/event_source/devices/cpu/events/cache-misses
event=0x400f0
This patch is based on commits that implement this functionality on x86.
Eg:
commit a47473939d
Author: Jiri Olsa <jolsa@redhat.com>
Date: Wed Oct 10 14:53:11 2012 +0200
perf/x86: Make hardware event translations available in sysfs
Changelog:[v2]
[Jiri Osla] Drop EVENT_ID() macro since it is only used once.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062454.GD13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Define and use macros to identify perf events codes This would make it
easier and more readable when these event codes need to be used in more
than one place.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062353.GB13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Early driver probing can fail due to not available clocks
(clk_get() fails) since the clk API init didn't take place yet.
Move clocks init before bus probing.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
There are now two kinds of DMA windows that might be presented by
PowerVM DDW support -- huge windows (that can map all of system memory
regardless of the LPAR configuration) and non-huge windows (which
can't). They are implemented slightly differently in PowerVM, and thus
have different characteristics. The most obvious is that slot isolate
doesn't clear the TCEs/window for us with non-huge windows. Thus, when a
DLPAR operation occurs on a slot using a non-huge window, TCEs are still
present (the notifier chain doesn't currently remove them explicitly)
and the DLPAR fails. Fix this by calling remove_ddw() first, which will
unmap the DDW TCEs.
Note: a corresponding change to drmgr is needed to actually successfully
DLPAR, such that the device-tree update (which causes the notifier chain
to fire) occurs before slot isolate.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tce_clearrange_multi_pSeriesLP is attempting to iterate over all TCEs in
a given range. However, is it not advancing the dma_offset value passed
to plpar_tce_stuff via the next value. This prevents DLPAR from
completing, because TCEs are still present at slot isolation time.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the hardware breakpoint code so that we can support wider ranged
breakpoints.
This means both ptrace and perf hardware breakpoints can use upto 512 byte long
breakpoints when using the DAWR and only 8 byte when using the DABR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we set the length field in the DAWR to 0 which defaults it to one
double word (64bits) which is the same as the DABR.
Change this so that we can set it to longer values as supported by the DAWR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
perf/Power: PERF_EVENT_IOC_ENABLE does not reenable event
If we disable a perf event because we exceeded the specified ->event_limit,
power_pmu_stop() sets the PERF_HES_STOPPED flag on the event.
If the application then re-enables the event using PERF_EVENT_IOC_ENABLE
ioctl, we don't ever clear this STOPPED flag. Consequently, the user space
is never notified of the event.
Following message has more background and test case.
http://lists.eecs.utk.edu/pipermail/ptools-perfapi/2012-October/002528.html
Used the following test cases to verify that this patch works on latest PAPI.
$ papi.git/src/ctests/nonthread PAPI_TOT_CYC@5000000
$ papi.git/src/ctests/overflow_single_event
Changelog[v2]:
- [Paul Mackerras] Also clear PERF_HES_UPTODATE flag since we are
restarting the event; cleanup comments and patch description.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use local_paca directly in macro SHARED_PROCESSOR, as all processors
have the same value for the field shared_proc, so we don't need care
racy here.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Uprobes uses emulate_step in sstep.c, but we haven't explicitly specified
the dependency. On pseries HAVE_HW_BREAKPOINT protects us, but 44x has no
such luxury.
Consolidate other users that depend on sstep and create a new config option.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: linuxppc-dev@ozlabs.org
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CTS-1000 is based on P4080. GPIO 27 is used to signal the FPGA to
switch off power, and also associates IRQ 8 with front-panel button
press (which we use to call orderly_poweroff()).
The relevant device-tree looks like this:
gpio0: gpio@130000 {
compatible = "fsl,qoriq-gpio";
reg = <0x130000 0x1000>;
interrupts = <55 2 0 0>;
#gpio-cells = <2>;
gpio-controller;
/* Allows powering off the system via GPIO signal. */
gpio-halt@27 {
compatible = "sgy,gpio-halt";
gpios = <&gpio0 27 0>;
interrupts = <8 1 0 0>;
};
};
Because the driver cannot match on sgy,gpio-halt (because the node is never
processed through of_platform), it matches on fsl,qoriq-gpio and then
checks child nodes for the matching sgy,gpio-halt. This also ensures that
the GPIO controller is detected prior to sgy_cts1000's probe callback,
since that node wont match via of_platform until the controller is
registered.
Also, because the GPIO handler for triggering system poweroff might sleep,
the IRQ uses a workqueue to call orderly_poweroff().
As a final note, this driver may be expanded for other features specific to
the CTS-1000.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Jack Smith <jack.s@servergy.com>
Cc: Vihar Rai <vihar.r@servergy.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While this should be harmless now that distribute_irqs
obeys MPIC_SINGLE_DEST_CPU, there's no reason to enable this
on mpc85xx/mpc86xx since MPIC_SINGLE_DEST_CPU will always be set.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previously we were setting an illegal configuration on mpc85xx
MPICs if CONFIG_IRQ_ALL_CPUS is enabled (which for some reason it is
in mpc85xx_smp_defconfig).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a mix of decimal and hex here, so lets make them consistently
hex. Also, strace will print them in hex if it can't decode them, so
having them in hex here makes it easier to match up.
No functional change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only persistent change made by this loop is calling
memblock_set_node() once for each memblock, which is not useful (and has
no effect) as memblock_set_node() is not called with any
memblock-specific parameters.
Subsistute a single memblock_set_node().
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With lazy interrupt, we always call __check_irq_replaysome with
decrementers_next_tb to check if we need to replay timer interrupt.
So in hotplug case we also need to set decrementers_next_tb as MAX
to make sure __check_irq_replay don't replay timer interrupt
when return as we expect, otherwise we'll trap here infinitely.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
the variable backup_current_thread_info isn't freed before existing the
function.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an
error. The calculation is should be to shift left by (max_cntrs - cntr) times
the width of the pmsel field width. However, the #define OPROFILE_MAX_PMC_NUM
was used instead of OPROFILE_PMSEL_FIELD_WIDTH. This patch fixes the
calculation.
Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit f96972f2dc "kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()"
added a call to disable_nonboot_cpus() on kernel_restart(), which tries
to shutdown all the CPUs except the first one. The issue with the PA
Semi, is that it does not support CPU hotplug.
When the call is made to __cpu_down(), it calls the notifiers
CPU_DOWN_PREPARE, and then tries to take the CPU down.
One of the notifiers to the CPU hotplug code, is the cpufreq. The
DOWN_PREPARE will call __cpufreq_remove_dev() which calls
cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O
that is used by an interrupt that goes off constantly
(system_reset_common, but it goes off during normal system operations
too). I'm not sure exactly what this interrupt does.
Running a simple function trace, you can see it goes off quite a bit:
# tracer: function
#
# TASK-PID CPU# TIMESTAMP FUNCTION
# | | | | |
<idle>-0 [001] 1558.859363: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.860112: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.861109: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [001] 1558.861361: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.861437: .pasemi_system_reset_exception <-.system_reset_exception
When the region is unmapped, the system crashes with:
Disabling non-boot CPUs ...
Error taking CPU1 down: -38
Unable to handle kernel paging request for data at address 0xd0000800903a0100
Faulting instruction address: 0xc000000000055fcc
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=64 NUMA PA Semi PWRficient
Modules linked in: shpchp
NIP: c000000000055fcc LR: c000000000055fb4 CTR: c0000000000df1fc
REGS: c0000000012175d0 TRAP: 0300 Not tainted (3.8.0-rc4-test-dirty)
MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR: 24000088 XER: 00000000
SOFTE: 0
DAR: d0000800903a0100, DSISR: 42000000
TASK = c0000000010e9008[0] 'swapper/0' THREAD: c000000001214000 CPU: 0
GPR00: d0000800903a0000 c000000001217850 c0000000012167e0 0000000000000000
GPR04: 0000000000000000 0000000000000724 0000000000000724 0000000000000000
GPR08: 0000000000000000 0000000000000000 0000000000000001 0000000000a70000
GPR12: 0000000024000080 c00000000fff0000 ffffffffffffffff 000000003ffffae0
GPR16: ffffffffffffffff 0000000000a21198 0000000000000060 0000000000000000
GPR20: 00000000008fdd35 0000000000a21258 000000003ffffaf0 0000000000000417
GPR24: 0000000000a226d0 c000000000000000 0000000000000000 0000000000000000
GPR28: c00000000138b358 0000000000000000 c000000001144818 d0000800903a0100
NIP [c000000000055fcc] .set_astate+0x5c/0xa4
LR [c000000000055fb4] .set_astate+0x44/0xa4
Call Trace:
[c000000001217850] [c000000000055fb4] .set_astate+0x44/0xa4 (unreliable)
[c0000000012178f0] [c00000000005647c] .restore_astate+0x2c/0x34
[c000000001217980] [c000000000054668] .pasemi_system_reset_exception+0x6c/0x88
[c000000001217a00] [c000000000019ef0] .system_reset_exception+0x48/0x84
[c000000001217a80] [c000000000001e40] system_reset_common+0x140/0x180
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit 12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Do some ground preparatory work before adding guest_enter()
and guest_exit() context tracking callbacks. Those will
be later used to read the guest cputime safely when we
run in full dynticks mode.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
If we want to stop the tick further idle, we need to be
able to account the cputime without using the tick.
Virtual based cputime accounting solves that problem by
hooking into kernel/user boundaries.
However implementing CONFIG_VIRT_CPU_ACCOUNTING require
low level hooks and involves more overhead. But we already
have a generic context tracking subsystem that is required
for RCU needs by archs which plan to shut down the tick
outside idle.
This patch implements a generic virtual based cputime
accounting that relies on these generic kernel/user hooks.
There are some upsides of doing this:
- This requires no arch code to implement CONFIG_VIRT_CPU_ACCOUNTING
if context tracking is already built (already necessary for RCU in full
tickless mode).
- We can rely on the generic context tracking subsystem to dynamically
(de)activate the hooks, so that we can switch anytime between virtual
and tick based accounting. This way we don't have the overhead
of the virtual accounting when the tick is running periodically.
And one downside:
- There is probably more overhead than a native virtual based cputime
accounting. But this relies on hooks that are already set anyway.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
The guest TLB handling code should not have any insight into how the host
TLB shadow code works.
kvmppc_e500_tlbil_all() is a function that is used for distinction between
e500v2 and e500mc (E.HV) on how to flush shadow entries. This function really
is private between the e500.c/e500mc.c file and e500_mmu_host.c.
Instead of this one, use the public kvmppc_core_flush_tlb() function to flush
all shadow TLB entries. As a nice side effect, with this we also end up
flushing TLB1 entries which we forgot to do before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Host shadow TLB flushing is logic that the guest TLB code should have
no insight about. Declare the internal clear_tlb_refs and clear_tlb1_bitmap
functions static to the host TLB handling file.
Instead of these, we can use the already exported kvmppc_core_flush_tlb().
This gives us a common API across the board to say "please flush any
pending host shadow translation".
Signed-off-by: Alexander Graf <agraf@suse.de>
When a host mapping fault happens in a guest TLB1 entry today, we
map the translated guest entry into the host's TLB1.
This isn't particularly clever when the guest is mapped by normal 4k
pages, since these would be a lot better to put into TLB0 instead.
This patch adds the required logic to map 4k TLB1 shadow maps into
the host's TLB0.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch splits the file e500_tlb.c into e500_mmu.c (guest TLB handling)
and e500_mmu_host.c (host TLB handling).
The main benefit of this split is readability and maintainability. It's
just a lot harder to write dirty code :).
Signed-off-by: Alexander Graf <agraf@suse.de>
When emulating tlbwe, we want to automatically map the entry that just got
written in our shadow TLB map, because chances are quite high that it's
going to be used very soon.
Today this happens explicitly, duplicating all the logic that is in
kvmppc_mmu_map() already. Just call that one instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
When shadow mapping a page, mapping this page can fail. In that case we
don't have a shadow map.
Take this case into account, otherwise we might end up writing bogus TLB
entries into the host TLB.
While at it, also move the write_stlbe() calls into the respective TLBn
handlers.
Signed-off-by: Alexander Graf <agraf@suse.de>
When we invalidate shadow TLB maps on the host, we don't mark them
as not valid. But we should.
Fix this by removing the E500_TLB_VALID from their flags when
invalidating.
Signed-off-by: Alexander Graf <agraf@suse.de>
Later patches want to call the function and it doesn't have
dependencies on anything below write_host_tlbe.
Move it higher up in the file.
Signed-off-by: Alexander Graf <agraf@suse.de>
Definitions and macros for implementing soreusport.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Arnd Bergmann <arnd@arndb.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Kumar Gala <galak@kernel.crashing.org>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Alexander Graf <agraf@suse.de>
CC: Avi Kivity <avi@redhat.com>
CC: Marcelo Tosatti <mtosatti@redhat.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up all callers as they were before, with make one change: an
unsigned module taints the kernel, but doesn't turn off lockdep.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is to fix up a build problem with a wireless driver due to the
dynamic-debug patches in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guests can trigger MMIO exits using dcbf. Since we don't emulate cache
incoherent MMIO, just do nothing and move on.
Reported-by: Ben Collins <ben.c@servergy.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Ben Collins <ben.c@servergy.com>
CC: stable@vger.kernel.org
While a privileged program can open a raw socket, attach some
restrictive filter and drop its privileges (or send the socket to an
unprivileged program through some Unix socket), the filter can still
be removed or modified by the unprivileged program. This commit adds a
socket option to lock the filter (SO_LOCK_FILTER) preventing any
modification of a socket filter program.
This is similar to OpenBSD BIOCLOCK ioctl on bpf sockets, except even
root is not allowed change/drop the filter.
The state of the lock can be read with getsockopt(). No error is
triggered if the state is not changed. -EPERM is returned when a user
tries to remove the lock or to change/remove the filter while the lock
is active. The check is done directly in sk_attach_filter() and
sk_detach_filter() and does not affect only setsockopt() syscall.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this option is to allow ARM/etc systems that rely on the
class RTC subsystem to have the same kind of automatic NTP based
synchronization that we have on PC platforms. Today ARM does not
implement update_persistent_clock and makes extensive use of the class
RTC system.
When enabled CONFIG_RTC_SYSTOHC will provide a generic
rtc_update_persistent_clock that stores the current time in the RTC and
is intended complement the existing CONFIG_RTC_HCTOSYS option that loads
the RTC at boot.
Like with RTC_HCTOSYS the platform's update_persistent_clock is used
first, if it works. Platforms with mixed class RTC and non-RTC drivers
need to return ENODEV when class RTC should be used. Such an update for
PPC is included in this patch.
Long term, implementations of update_persistent_clock should migrate to
proper class RTC drivers and use CONFIG_RTC_SYSTOHC instead.
Tested on ARM kirkwood and PPC405
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The .dtsi now names all PSC nodes as "psc", so this ac97
check won't work. Check for ac97 PSC using compatible
property.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
With allmodconfig we are getting:
drivers/tty/synclink_gt.c:160:12: error: conflicting types for 'set_break'
arch/powerpc/include/asm/debug.h:49:5: note: previous declaration of 'set_break' was here
drivers/tty/synclinkmp.c:526:12: error: conflicting types for 'set_break'
arch/powerpc/include/asm/debug.h:49:5: note: previous declaration of 'set_break' was here
This renames set_break to set_breakpoint to avoid this naming conflict
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we are getting:
arch/powerpc/kernel/kgdb.c: In function 'kgdb_arch_exit':
arch/powerpc/kernel/kgdb.c:492:2: error: '__debugger_breakx_match' undeclared (first use in this function)
arch/powerpc/kernel/kgdb.c:492:2: note: each undeclared identifier is reported only once for each function it appears in
Fix the typo.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The DSCR (aka Data Stream Control Register) is supported on some
server PowerPC chips and allow some control over the prefetch
of data streams.
The kernel already supports DSCR value per thread but there is also
a need in a ability to change it from an external process for
the specific pid.
The patch adds new register index PT_DSCR (index=44) which can be
set/get by:
ptrace(PTRACE_POKEUSER, traced_process, PT_DSCR << 3, dscr);
dscr = ptrace(PTRACE_PEEKUSER, traced_process, PT_DSCR << 3, NULL);
The patch does not increase PT_REGS_COUNT as the pt_regs struct has not
been changed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Geoff Levand <geoff@infradead.org>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Pull KVM bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: use dynamic percpu allocations for shared msrs area
KVM: PPC: Book3S HV: Fix compilation without CONFIG_PPC_POWERNV
powerpc: Corrected include header path in kvm_para.h
Add rcu user eqs exception hooks for async page fault
We need to be able to read and write the contents of the EPR register
from user space.
This patch implements that logic through the ONE_REG API and declares
its (never implemented) SREGS counterpart as deprecated.
Signed-off-by: Alexander Graf <agraf@suse.de>
The External Proxy Facility in FSL BookE chips allows the interrupt
controller to automatically acknowledge an interrupt as soon as a
core gets its pending external interrupt delivered.
Today, user space implements the interrupt controller, so we need to
check on it during such a cycle.
This patch implements logic for user space to enable EPR exiting,
disable EPR exiting and EPR exiting itself, so that user space can
acknowledge an interrupt when an external interrupt has successfully
been delivered into the guest vcpu.
Signed-off-by: Alexander Graf <agraf@suse.de>
The EPR register is potentially valid for PR KVM as well, so we need
to emulate accesses to it. It's only defined for reading, so only
handle the mfspr case.
Signed-off-by: Alexander Graf <agraf@suse.de>
When injecting an interrupt into guest context, we usually don't need
to check for requests anymore. At least not until today.
With the introduction of EPR, we will have to create a request when the
guest has successfully accepted an external interrupt though.
So we need to prepare the interrupt delivery to abort guest entry
gracefully. Otherwise we'd delay the EPR request.
Signed-off-by: Alexander Graf <agraf@suse.de>
On mfspr/mtspr emulation path Book3E's MMUCFG SPR with value 1015 clashes
with G4's MSSSR0 SPR. Move MSSSR0 emulation from generic part to Books3S.
MSSSR0 also clashes with Book3S's DABRX SPR. DABRX was not explicitly
handled so Book3S execution flow will behave as before.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running on top of pHyp, the hypercall instruction "sc 1" goes
straight into pHyp without trapping in supervisor mode.
So if we want to support PAPR guest in this configuration we need to
add a second way of accessing PAPR hypercalls, preferably with the
exact same semantics except for the instruction.
So let's overlay an officially reserved instruction and emulate PAPR
hypercalls whenever we hit that one.
Signed-off-by: Alexander Graf <agraf@suse.de>
When we hit an emulation result that we didn't expect, that is an error,
but it's nothing that warrants a BUG(), because it can be guest triggered.
So instead, let's only WARN() the user that this happened.
Signed-off-by: Alexander Graf <agraf@suse.de>
The FWNMI region is fixed at 0x7000 and the vector are now
overflowing that with some configurations. Fix that by moving
some hash management code out of that region as it doesn't need
to be that close to the call sites (isn't accessed using
conditional branches).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On POWER7 when we have really small counts left before overflow, we can take a
PMU IRQ, but the PMC gets wound back to just before the overflow.
If the kernel is setting the PMC to a value just before the overflow, we can
get interrupted again without the PMC making any progress (ie another buggy
overflow). In this case, we can end up making no forward progress, with the
PMC interrupt returning us to the same count over and over.
The below detects when we are making no forward progress (ie. delta = 0) and
then increases the amount left before the overflow. This stops us from locking
up.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
cc: Paul Mackerras <paulus@samba.org>
cc: Anton Blanchard <anton@samba.org>
cc: Linux PPC dev <linuxppc-dev@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a PMC is about to overflow on a counter that's on an active perf event
(ie. less than 256 from the end) and a _different_ PMC overflows just at this
time (a PMC that's not on an active perf event), we currently mark the event as
found, but in reality it's not as it's likely the other PMC that caused the
IRQ. Since we mark it as found the second catch all for overflows doesn't run,
and we don't reset the overflowing PMC ever. Hence we keep hitting that same
PMC IRQ over and over and don't reset the actual overflowing counter.
This is a rewrite of the perf interrupt handler for book3s to get around this.
We now check to see if any of the PMCs have actually overflowed (ie >=
0x80000000). If yes, record it for active counters and just reset it for
inactive counters. If it's not overflowed, then we check to see if it's one of
the buggy power7 counters and if it is, record it and continue. If none of the
PMCs match this, then we make note that we couldn't find the PMC that caused
the IRQ.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
cc: Paul Mackerras <paulus@samba.org>
cc: Anton Blanchard <anton@samba.org>
cc: Linux PPC dev <linuxppc-dev@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The DDW code uses a eeh_dev struct from the pci_dev. However, this is
not set until eeh_add_device_late is called.
Since pci_bus_add_devices is called before eeh_add_device_late, the PCI
devices are added to the bus, making drivers' probe hooks to be called.
These will call set_dma_mask, which will call the DDW code, which will
require the eeh_dev struct from pci_dev. This would result in a crash,
due to a NULL dereference.
Calling eeh_add_device_late after pci_bus_add_devices would make the
system BUG, because device files shouldn't be added to devices there
were not added to the system. So, a new function is needed to add such
files only after pci_bus_add_devices have been called.
Cc: stable@vger.kernel.org
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The functions used are already defined as empty inline functions for the
case where EEH is disabled.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When a device DMA window includes the address 0, it's reserved in the
TCE bitmap to avoid returning that address to drivers.
When the device is removed, the bitmap is checked for any mappings not
removed by the driver, indicating a possible DMA mapping leak. Since the
reserved address is not cleared, a message is printed, warning of such a
leak.
Check for the reservation, and clear it before checking for any other
standing mappings.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds DAWR supoprt to the set_break().
It does both bare metal and PAPR versions of setting the DAWR.
There is still some work we can do to make full use of the watchpoint but that
will come later.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a rewrite so that we don't assume we are using the DABR throughout the
code. We now use the arch_hw_breakpoint to store the breakpoint in a generic
manner in the thread_struct, rather than storing the raw DABR value.
The ptrace GET/SET_DEBUGREG interface currently passes the raw DABR in from
userspace. We keep this functionality, so that future changes (like the POWER8
DAWR), will still fake the DABR to userspace.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
.. and add it to POWER8 cpu features.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These are just wrappers around the new set_mode HCALL.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This frees up 7 bits for crazy new CPU features.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These are 32 bit, so no need to have a bunch of wasted 0s.
The 0s saved here can be put to better use elsewhere, like at the end of my pay
check.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ppc64 ABI has a static chain register (r11) which is only used
when calling nested functions through a pointer. Considering that
we take a dim view of nested functions in the kernel, we have a lot
of unnecessary overhead here.
gcc 4.7 has an option to disable loading of r11 so lets use it.
If hell freezes over and hipsters manage to litter the kernel
with nested functions, gcc will give us an error message and
won't simply compile bad code:
You cannot take the address of a nested function if you use
the -mno-pointers-to-nested-functions option.
Furthermore our kernel module trampolines don't setup the static
chain register so adding this option and forcing gcc to error out
makes even more sense.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need devtmpfs enabled to boot on recent versions of Fedora. EFI
partitions will be useful for large block devices. tmpfs ACL support
is used by some distros for managing access to devices.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Set CONFIG_NLS_DEFAULT to utf8. The distros do this (eg ppc64 FC17
and RHEL6) as well as the x86 defconfigs. Userspace these days is
most likely to expect utf8 anyway.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No changes, just update the configs with savedefconfig.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new vsprintf extension to avoid any possible
message interleaving.
Convert the #ifdef DEBUG block to a single pr_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[PATCH 6/6] powerpc: Implement PPR save/restore
When the task enters in to kernel space, the user defined priority (PPR)
will be saved in to PACA at the beginning of first level exception
vector and then copy from PACA to thread_info in second level vector.
PPR will be restored from thread_info before exits the kernel space.
P7/P8 temporarily raises the thread priority to higher level during
exception until the program executes HMT_* calls. But it will not modify
PPR register. So we save PPR value whenever some register is available
to use and then calls HMT_MEDIUM to increase the priority. This feature
supports on P7 or later processors.
We save/ restore PPR for all exception vectors except system call entry.
GLIBC will be saving / restore for system calls. So the default PPR
value (3) will be set for the system call exit when the task returned
to the user space.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[PATCH 5/6] powerpc: Macros for saving/restore PPR
Several macros are defined for saving and restore user defined PPR value.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[PATCH 4/6] powerpc: Define ppr in thread_struct
ppr in thread_struct is used to save PPR and restore it before process exits
from kernel.
This patch sets the default priority to 3 when tasks are created such
that users can use 4 for higher priority tasks.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[PATCH 3/6] powerpc: Increase exceptions arrays in paca struct to save PPR
Using paca to save user defined PPR value in the first level exception vector.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[PATCH 2/6] powerpc: Enable PPR save/restore
SMT thread status register (PPR) is used to set thread priority. This patch
enables PPR save/restore feature (CPU_FTR_HAS_PPR) on POWER7 and POWER8 systems.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[PATCH 1/6] powerpc: Move branch instruction from ACCOUNT_CPU_USER_ENTRY to caller
The first instruction in ACCOUNT_CPU_USER_ENTRY is 'beq' which checks for
exceptions coming from kernel mode. PPR value will be saved immediately after
ACCOUNT_CPU_USER_ENTRY and is also for user level exceptions. So moved this
branch instruction in the caller code.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Support for stalled-cycles-frontend and stalled-cycles-backend is
added for e500-based processors.
The following mappings are used:
stalled-cycles-frontend or idle-cycles-frontend:
Com:18 Cycles decode stalled
stalled-cycles-backend or idle-cycles-backend
Com:19 cycles issue stalled
Signed-off-by: Chris Freehill <chrisf@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
By using the compiler intrinsics instead of hand-crafted opaque inline
assembler for byte-swapping, we let the compiler see what's actually
happening and it gets to use lwbrx/stwbrx instructions instead of a
normal load/store coupled with a sequence of rlwimi instructions to
move bits around.
Compiled-tested only. It gave a code size reduction of almost 4% for
ext2, and more like 2.5% for ext3/ext4.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use for_each_compatible_node() macro instead of open coding it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use for_each_compatible_node() macro instead of open coding it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For PR KVM we allow userspace to map 0xc000000000000000. Because
transitioning from userspace to the guest kernel may use the relocated
exception vectors we have to disable relocation on exceptions whenever
PR KVM is active as we cannot trust that address.
This issue does not apply to HV KVM, since changing from a guest to the
hypervisor will never use the relocated exception vectors.
Currently the hypervisor interface only allows us to toggle relocation
on exceptions on a partition wide scope, so we need to globally disable
relocation on exceptions when the first PR KVM instance is started and
only re-enable them when all PR KVM instances have been destroyed.
It's a bit heavy handed, but until the hypervisor gives us a lightweight
way to toggle relocation on exceptions on a single thread it's only real
option.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Motivation:
IBM Blue Gene/Q comes with some very strange firmware that I'm trying to get out
of using in the kernel. So instead I spin all the threads in the boot wrapper
(using the firmware) and have them enter the kexec stub, pre-translated at the
virtual "linear" address, never touching firmware again.
This works strategy works wonderfully, but I need the following patch in the
kexec stub. I believe it should not effect Book3S and Book3E does not appear
to be here yet so I'd love to get any criticisms up front.
This patch adds two items:
1) Book3e requires that GPR4 survive the "hold" process, so we make
sure that happens.
2) Book3e has no real mode, and the hold code exploits this. Since
these processors ares always translated, we arrange for the kexeced
threads to enter the hold code using the normal kernel linear mapping.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit 12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Finally remove the two level TOC and build with -mcmodel=medium.
Unfortunately we can't build modules with -mcmodel=medium due to
the tricks the kernel module loader plays with percpu data:
# -mcmodel=medium breaks modules because it uses 32bit offsets from
# the TOC pointer to create pointers where possible. Pointers into the
# percpu data area are created by this method.
#
# The kernel module loader relocates the percpu data section from the
# original location (starting with 0xd...) to somewhere in the base
# kernel percpu data space (starting with 0xc...). We need a full
# 64bit relocation for this to work, hence -mcmodel=large.
On older kernels we fall back to the two level TOC (-mminimal-toc)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now we relocate prom_init.c on 64bit we can finally remove the
nasty RELOC() macro.
Finally a patch that I can claim has a net positive effect on
the kernel. It doesn't happen very often.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ppc64 kernel can get loaded at any address which means
our very early init code in prom_init.c must be relocatable. We do
this with a pretty nasty RELOC() macro that we wrap accesses of
variables with. It is very fragile and sometimes we forget to add a
RELOC() to an uncommon path or sometimes a compiler change breaks it.
32bit has a much more elegant solution where we build prom_init.c
with -mrelocatable and then process the relocations manually.
Unfortunately we can't do the equivalent on 64bit and we would
have to build the entire kernel relocatable (-pie), resulting in a
large increase in kernel footprint (megabytes of relocation data).
The relocation data will be marked __initdata but it still creates
more pressure on our already tight memory layout at boot.
Alan Modra pointed out that the 64bit ABI is relocatable even
if we don't build with -pie, we just need to relocate the TOC.
This patch implements that idea and relocates the TOC entries of
prom_init.c. An added bonus is there are very few relocations to
process which helps keep boot times on simulators down.
gcc does not put 64bit integer constants into the TOC but to be
safe we may want a build time script which passes through the
prom_init.c TOC entries to make sure everything looks reasonable.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable PRINTK_TIME in pasemi_defconfig. Also regenerate it, it seems
that a lot of options have moved around since last time savedefconfig
was ran on it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The third argument for of_get_property() is a pointer, hence pass
NULL instead of 0.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the representation of the PMU flags from decimal to hex since they
are bitfields which are easier to read in hex.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch actually hooks up doorbell interrupts on POWER8:
- Select the PPC_DOORBELL Kconfig option from PPC_PSERIES
- Add the doorbell CPU feature bit to POWER8
- We define a new pSeries_cause_ipi_mux() function that issues a
doorbell interrupt if the recipient is another thread within the same
core as the sender. If the recipient is in a different core it falls
back to using XICS to deliver the IPI as before.
- During pSeries_smp_probe() at boot, we check if doorbell interrupts
are supported. If they are we set the cause_ipi function pointer to
the above mentioned function, otherwise we leave it as whichever XICS
cause_ipi function was determined by xics_smp_probe().
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the rule to build doorbell support out of the Makefile and into a
new Kconfig boolean that platforms can select.
We will add doorbell support to pseries as well in the next patch.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the logic to properly handle doorbells that come in when
interrupts have been soft disabled and to replay them when interrupts
are re-enabled:
- masked_##_H##interrupt is modified to leave interrupts enabled when a
doorbell has come in since doorbells are edge sensitive and as such
won't be automatically re-raised.
- __check_irq_replay now tests if a doorbell happened on book3s, and
returns either 0xe80 or 0xa00 depending on whether we are the
hypervisor or not.
- restore_check_irq_replay now tests for the two possible server
doorbell vector numbers to replay.
- __replay_interrupt also adds tests for the two server doorbell vector
numbers, and is modified to use a compare instruction rather than an
andi. on the single bit difference between 0x500 and 0x900.
The last two use a CPU feature section to avoid needlessly testing
against the hypervisor vector if it is not the hypervisor, and vice
versa.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On book3s we have two msgsnd instructions with differing privilege
levels. This patch selects the appropriate instruction to use whenever
we send a doorbell interrupt.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Directed Privileged Doorbell Interrupts come in at 0xa00 (or
0xc000000000004a00 if relocation on exception is enabled), so add
exception vectors at these locations.
If doorbell support is not compiled in we handle it as an
unknown_exception.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Directed Hypervisor Doorbell Interrupts come in at 0xe80 (or
0xc000000000004e80 if relocation on exceptions is enabled), so add
exception vectors at these locations.
If doorbell support is not compiled in we handle it as an
unknown_exception.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a few key differences between doorbells on server compared
with embedded that we care about on Linux, namely:
- We have a new msgsndp instruction for directed privileged doorbells.
msgsnd is used for directed hypervisor doorbells.
- The tag we use in the instruction is the Thread Identification
Register of the recipient thread (since server doorbells can only
occur between threads within a single core), and is only 7 bits wide.
- A new message type is introduced for server doorbells (none of the
existing book3e message types are currently supported on book3s).
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the marvel phy which is present on the ml507 board.
Without this ethtool causes kernel-oopses.
Tested on ml507 board.
Signed-off-by: Gernot Vormayr <gvormayr@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch consists of:
- Add driver for OCM component
- Export OCM Information at /sys/kernel/debug/ppc4xx_ocm/info
Signed-off-by: Vinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we search for the best_energy hcall using a custom function. Move
this to using the firmware_feature_table.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
cc: Linux PPC dev <linuxppc-dev@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows firmware_features_table names to add a '*' at the end so that only
partial strings are matched.
When a '*' is added, only upto the '*' is matched when setting firmware feature
bits.
This is useful for the matching best energy feature.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
cc: Linux PPC dev <linuxppc-dev@ozlabs.org>
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The watchdog and FIT code has been #if 0'd for ever, if the CPU takes
an exception to either of those vectors it will jump into the middle
of the PIT or Data TLB code and surely crash.
At least some (all?) 405 cores have both the WDT and FIT
vectors defined, so lets have proper entry points for them.
Tested that the WDT vector works on a 405F6 core.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pseries CPU hotplug code uses cede_processor without properly
synchronizing the SW and HW interrupt enable state. This fixes
it using the same helpers that were written for the idle code.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
=======================
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a crypto driver which provides a powerpc accelerated
implementation of SHA-1, accelerated in that it is written in asm.
Original patch by Paul, minor fixups for upstream by moi.
Lightly tested on 64-bit with the test program here:
http://michael.ellerman.id.au/files/junkcode/sha1test.c
Seems to work, and is "not slower" than the generic version.
Needs testing on 32-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes this build breakage:
arch/powerpc/kvm/book3s_hv_ras.c: In function ‘kvmppc_realmode_mc_power7’:
arch/powerpc/kvm/book3s_hv_ras.c:126:23: error: ‘struct paca_struct’ has no member named ‘opal_mc_evt’
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Here are the remaining __dev* removal patches against the 3.8-rc2 tree.
All of these patches were previously sent to the subsystem maintainers,
most of them were picked up and pushed to you, but there were a number
that fell through the cracks, and new drivers were added during the
merge window, so this series cleans up the rest of the instances of
these markings.
Third time's the charm...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDmHOIACgkQMUfUDdst+ykTZgCePgK84Im3FFooEXJwaPbaf4ls
lO4AoMEDoWK+BHWOsjQwFPOwFFPEN2Xh
=6oAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core __dev* removal patches - take 3 - from Greg Kroah-Hartman:
"Here are the remaining __dev* removal patches against the 3.8-rc2
tree. All of these patches were previously sent to the subsystem
maintainers, most of them were picked up and pushed to you, but there
were a number that fell through the cracks, and new drivers were added
during the merge window, so this series cleans up the rest of the
instances of these markings.
Third time's the charm...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflict with the pinctrl pull in pinctrl-sirf.c.
* tag 'driver-core-3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
misc: remove __dev* attributes.
include: remove __dev* attributes.
Documentation: remove __dev* attributes.
Drivers: misc: remove __dev* attributes.
Drivers: block: remove __dev* attributes.
Drivers: bcma: remove __dev* attributes.
Drivers: char: remove __dev* attributes.
Drivers: clocksource: remove __dev* attributes.
Drivers: ssb: remove __dev* attributes.
Drivers: dma: remove __dev* attributes.
Drivers: gpu: remove __dev* attributes.
Drivers: infinband: remove __dev* attributes.
Drivers: memory: remove __dev* attributes.
Drivers: mmc: remove __dev* attributes.
Drivers: iommu: remove __dev* attributes.
Drivers: power: remove __dev* attributes.
Drivers: message: remove __dev* attributes.
Drivers: macintosh: remove __dev* attributes.
Drivers: mfd: remove __dev* attributes.
pstore: remove __dev* attributes.
...
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bestcomm dma hardware, and some of its users like the FEC ethernet
component, is used in different FreeScale parts, including non-powerpc
parts like the ColdFire MCF547x & MCF548x families. Don't keep the
driver hidden in arch/powerpc where it is inaccessible for other arches.
.c files are moved to drivers/dma/bestcomm, while .h files are moved to
include/linux/fsl/bestcomm. Makefiles, Kconfigs and #include directives
are updated for the new file locations.
Tested by recompiling for MPC5200 with all bestcomm users enabled.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The locking in update_vsyscall_tz() is not only unnecessary because the vdso
code copies the data unproteced in __kernel_gettimeofday() but also
introduces a hard to reproduce race condition between update_vsyscall()
and update_vsyscall_tz(), which causes user space process to loop
forever in vdso code.
The following patch removes the locking from update_vsyscall_tz().
Locking is not only unnecessary because the vdso code copies the data
unprotected in __kernel_gettimeofday() but also erroneous because updating
the tb_update_count is not atomic and introduces a hard to reproduce race
condition between update_vsyscall() and update_vsyscall_tz(), which further
causes user space process to loop forever in vdso code.
The below scenario describes the race condition,
x==0 Boot CPU other CPU
proc_P: x==0
timer interrupt
update_vsyscall
x==1 x++;sync settimeofday
update_vsyscall_tz
x==2 x++;sync
x==3 sync;x++
sync;x++
proc_P: x==3 (loops until x becomes even)
Because the ++ operator would be implemented as three instructions and not
atomic on powerpc.
A similar change was made for x86 in commit 6c260d5863
("x86: vdso: Remove bogus locking in update_vsyscall_tz")
Signed-off-by: Shan Hai <shan.hai@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull VFS update from Al Viro:
"fscache fixes, ESTALE patchset, vmtruncate removal series, assorted
misc stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (79 commits)
vfs: make lremovexattr retry once on ESTALE error
vfs: make removexattr retry once on ESTALE
vfs: make llistxattr retry once on ESTALE error
vfs: make listxattr retry once on ESTALE error
vfs: make lgetxattr retry once on ESTALE
vfs: make getxattr retry once on an ESTALE error
vfs: allow lsetxattr() to retry once on ESTALE errors
vfs: allow setxattr to retry once on ESTALE errors
vfs: allow utimensat() calls to retry once on an ESTALE error
vfs: fix user_statfs to retry once on ESTALE errors
vfs: make fchownat retry once on ESTALE errors
vfs: make fchmodat retry once on ESTALE errors
vfs: have chroot retry once on ESTALE error
vfs: have chdir retry lookup and call once on ESTALE error
vfs: have faccessat retry once on an ESTALE error
vfs: have do_sys_truncate retry once on an ESTALE error
vfs: fix renameat to retry on ESTALE errors
vfs: make do_unlinkat retry once on ESTALE errors
vfs: make do_rmdir retry once on ESTALE errors
vfs: add a flags argument to user_path_parent
...
Pull signal handling cleanups from Al Viro:
"sigaltstack infrastructure + conversion for x86, alpha and um,
COMPAT_SYSCALL_DEFINE infrastructure.
Note that there are several conflicts between "unify
SS_ONSTACK/SS_DISABLE definitions" and UAPI patches in mainline;
resolution is trivial - just remove definitions of SS_ONSTACK and
SS_DISABLED from arch/*/uapi/asm/signal.h; they are all identical and
include/uapi/linux/signal.h contains the unified variant."
Fixed up conflicts as per Al.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to generic sigaltstack
new helpers: __save_altstack/__compat_save_altstack, switch x86 and um to those
generic compat_sys_sigaltstack()
introduce generic sys_sigaltstack(), switch x86 and um to it
new helper: compat_user_stack_pointer()
new helper: restore_altstack()
unify SS_ONSTACK/SS_DISABLE definitions
new helper: current_user_stack_pointer()
missing user_stack_pointer() instances
Bury the conditionals from kernel_thread/kernel_execve series
COMPAT_SYSCALL_DEFINE: infrastructure
Where we can pass in LOOKUP_DIRECTORY or LOOKUP_REVAL. Any other flags
passed in here are currently ignored.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes to
some architectures which make use of dma-debug. Most of these changes
have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor the
IOMMU-Groups support and to make sure it does not trigger a hardware
erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The conflict
is in the file arch/arm/mach-omap2/clock44xx_data.c which is deleted in
the arm-soc tree. It is safe to delete the file too so solve the
conflict. Similar changes are done in the arm-soc tree in the common
clock framework migration. A missing hunk from the patch in the IOMMU
tree will be submitted as a seperate patch when the merge-window is
closed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pPHZ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes
to some architectures which make use of dma-debug. Most of these
changes have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor
the IOMMU-Groups support and to make sure it does not trigger a
hardware erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The
conflict is in the file arch/arm/mach-omap2/clock44xx_data.c which is
deleted in the arm-soc tree. It is safe to delete the file too so
solve the conflict. Similar changes are done in the arm-soc tree in
the common clock framework migration. A missing hunk from the patch
in the IOMMU tree will be submitted as a seperate patch when the
merge-window is closed."
* tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (29 commits)
ARM: dma-mapping: support debug_dma_mapping_error
ARM: OMAP4: hwmod data: ipu and dsp to use parent clocks instead of leaf clocks
iommu/omap: Adapt to runtime pm
iommu/omap: Migrate to hwmod framework
iommu/omap: Keep mmu enabled when requested
iommu/omap: Remove redundant clock handling on ISR
iommu/amd: Remove obsolete comment
iommu/amd: Don't use 512GB pages
iommu/tegra: smmu: Move bus_set_iommu after probe for multi arch
iommu/tegra: gart: Move bus_set_iommu after probe for multi arch
iommu/tegra: smmu: Remove unnecessary PTC/TLB flush all
tile: dma_debug: add debug_dma_mapping_error support
sh: dma_debug: add debug_dma_mapping_error support
powerpc: dma_debug: add debug_dma_mapping_error support
mips: dma_debug: add debug_dma_mapping_error support
microblaze: dma-mapping: support debug_dma_mapping_error
ia64: dma_debug: add debug_dma_mapping_error support
c6x: dma_debug: add debug_dma_mapping_error support
ARM64: dma_debug: add debug_dma_mapping_error support
intel-iommu: Prevent devices with RMRRs from being placed into SI Domain
...
The include/uapi/asm/kvm_para.h includes
<include/uapi/asm/epapr_hcalls.h> but the correct reference
should be <include/asm/epapr_hcalls.h> as this is the place
where make install_header installs the header files for
userspace.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
CC: stable@vger.kernel.org
Signed-off-by: Alexander Graf <agraf@suse.de>
Nishanth Aravamudan