When using HPDET to identify the accessory still run MICDET before we
report a microphone in order to ensure that the accessory identified is
compatible with the MICDET detection ranges after having confirmed that
the device is not using a headphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This should always be the most accurate reading for supported accessory
configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is important to clear the wake trigger status bits otherwise DCVDD
will be held high independent of the state of the LDOENA line.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The magic is already done as part of enabling the headphone output so
does not need to be done when the headphone outputs are enabled. We hold
the DAPM lock so the headphone status can't be changed underneath us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The HPDET identification method does not have the same natural debounce
built into it that the standard MICDET method does so add some extra on
top of what the jack detection does in hardware to make sure we get a
robust result.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When starting microphone detection some headsets should be exposed to
the fully regulated microphone bias in order to ensure that they behave
in an optimal fashion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to tune detection rate and debounce suitably for their
mechanical parameters.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We now have mechanisms in place to allow retries so let's use them rather
than guessing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we clamp as quickly as possible after removal by disabling the
debounce while there is an accessory present.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With some GPIO control it is possible to detect microphones in a wider
range of configurations by directly measuring the microphone impedance
when the HPDET method cannot distinguish between the behaviour of the
two grounds. Allow a GPIO to be provided in platform data and use it to
implement this behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The accessory detection functionality in Arizona devices is flexible and
supports several system designs in addition to the default one implemented
by the existing driver. One such design uses the HPDET feature to determine
what kind of accessory is present by comparing measurements taken with the
two headphone grounds available on the device, implement that if selected
by platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Use the headphone detection to identify if the accessory is a headphone or
line load. There are two different revisions of the IP with different
register layouts, support both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Some system designs provide an input on GPIO5 which in conjunction with
the jack detection feature indicates the presence of an accessory.
Support such systems, using the microphone clamp feature to minimise
wakeups of the processor.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Newer Arizona devices include a microphone clamp function which is tied to
jack detect. Activate this feature when present in order to ensure best
performance of the subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Allow configuration of the rise time for MICBIAS via platform data, the
delay required depends on things like the external component selection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The micd_pol GPIO is only requested if we've specified one greater than 0
so apply the same test before we set it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Now this is configured by platform data remove the defualt configuration
the driver had.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This is based on Linux 3.7 rc6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/KTt
-----END PGP SIGNATURE-----
Merge tag 'pull_req_20121122' of git://git.kernel.org/pub/scm/linux/kernel/git/mzx/extcon into char-misc-next
MyungJoo writes:
"extcon pull request targetting Linux 3.8 for Greg KH on 2012.11.22
This is based on Linux 3.7 rc6"
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If regmap_read() failed, arizona_micdet() returns IRQ_NONE
leaving &info->lock mutex locked as opposed to all other return paths.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago), and
some hyper-v updates and some printk fixes as well. All patches that
are outside of the drivers/base area have been acked by the respective
maintainers, and have all been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3vkACgkQMUfUDdst+ylQoACgldktGFgkCLzH+rGYthrXOC5P
9hUAnjmOhdoHlMTL81vWTlH+BrGernym
=khrr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core merge from Greg Kroah-Hartman:
"Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago),
and some hyper-v updates and some printk fixes as well. All patches
that are outside of the drivers/base area have been acked by the
respective maintainers, and have all been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
memory: tegra{20,30}-mc: Fix reading incorrect register in mc_readl()
device.h: Add missing inline to #ifndef CONFIG_PRINTK dev_vprintk_emit
memory: emif: Add ifdef CONFIG_DEBUG_FS guard for emif_debugfs_[init|exit]
Documentation: Fixes some translation error in Documentation/zh_CN/gpio.txt
Documentation: Remove 3 byte redundant code at the head of the Documentation/zh_CN/arm/booting
Documentation: Chinese translation of Documentation/video4linux/omap3isp.txt
device and dynamic_debug: Use dev_vprintk_emit and dev_printk_emit
dev: Add dev_vprintk_emit and dev_printk_emit
netdev_printk/netif_printk: Remove a superfluous logging colon
netdev_printk/dynamic_netdev_dbg: Directly call printk_emit
dev_dbg/dynamic_debug: Update to use printk_emit, optimize stack
driver-core: Shut up dev_dbg_reatelimited() without DEBUG
tools/hv: Parse /etc/os-release
tools/hv: Check for read/write errors
tools/hv: Fix exit() error code
tools/hv: Fix file handle leak
Tools: hv: Implement the KVP verb - KVP_OP_GET_IP_INFO
Tools: hv: Rename the function kvp_get_ip_address()
Tools: hv: Implement the KVP verb - KVP_OP_SET_IP_INFO
Tools: hv: Add an example script to configure an interface
...
We can perform microphone detection with MICVDD in bypass mode so try to
enable that during startup for minimal power - other users or machine
constraints will prevent bypass mode being activated if it is unsuitable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As well as identifying accessories the accessory detection hardware on
Arizona class devices can also detect a number of buttons which we should
report via the input API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no point in continuing to try to detect a microphone any
more so stop doing so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use extcon_set_state_ for performance and split the headset into separate
headphone and microphone reports as this is more idiomatic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most Wolfson Arizona class audio hub CODECs include a flexible ultra low
power accessory detection subsystem. This driver exposes initial support
for this subsystem via the Extcon framework, implementing support for
ultra low power detection of headphone and headset with the ability to
detect the polarity of a headset.
The functionality of the devices is much richer and more flexible than
the current driver, future patches will extend the features of the
driver to more fully exploit this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Brown