In order to prevent some pixels getting stuck in an unflushable FIFO on
bcm2711, we need to enable the HVS, the pixelvalve (the CRTC) and the HDMI
controller (the encoder) in an intertwined way, and with tight delays.
However, the atomic callbacks don't really provide a way to work with
either constraints, so we need to roll our own callbacks so that we can
provide those guarantees.
Since those callbacks have been implemented and called in the CRTC code, we
can just implement them in the HDMI driver now.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2e9226d971117065f3b97e597f04f7fe2f0c134c.1599120059.git-series.maxime@cerno.tech
In order to avoid a pixel getting stuck in an unflushable FIFO, we need to
recenter the FIFO every time we're doing a modeset and not only if we're
connected to an HDMI monitor.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b3faaf05ac6c4d3c364d28fa441571eb85903269.1599120059.git-series.maxime@cerno.tech
The current code has some logic, disabled by default, to dump the register
setup in the HDMI controller.
However, since we're going to split those functions in multiple, shorter,
functions that only make sense where they are called in sequence, keeping
the register dump makes little sense.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c8c8d388f2d32fc3536336be36d003a862487eb7.1599120059.git-series.maxime@cerno.tech
The HDMI driver was registering a single ALSA card so far with the name
vc4-hdmi.
Obviously, this is not going to work anymore when we will have multiple
HDMI controllers since we will end up trying to register two files with the
same name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e60a37444e848a384a45707a21d6df8883115f86.1599120059.git-series.maxime@cerno.tech
The audio configuration has changed for the BCM2711, with notably a
different parent clock and a different channel configuration.
Make that modular to be able to support the BCM2711.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/85a8ca721c2d800be758c55870cea98536749680.1599120059.git-series.maxime@cerno.tech
ALSA's iec958 plugin by default sets the block start preamble
to 8, whilst this driver was programming the hardware to expect
0xF.
Amend the hardware config to match ALSA.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d0b126deb228baf1244c91e02ac0a8f7c9c60dc5.1599120059.git-series.maxime@cerno.tech
If the encoder is disabled and re-enabled (eg mode change) all infoframes
are reset, whilst the audio subsystem know nothing about this change.
The driver therefore needs to reinstate the audio infoframe for
itself.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cd579ccc2c9b9d2fce0ebaf32f847cedb0e4a7a2.1599120059.git-series.maxime@cerno.tech
The register range used for audio setup in the previous generations of
SoC were always the second range in the device tree. However, now that
the BCM2711 has way more register ranges, it makes sense to retrieve it
by names for it, while preserving the id-based lookup as a fallback.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a1ba5605fe1006a1ead5262ef3d66ea5d0750381.1599120059.git-series.maxime@cerno.tech
The HSM clock needs to be running at 101% the pixel clock of the HDMI
controller, however it's shared between the two HDMI controllers, which
means that if the resolutions are different between the two HDMI
controllers, and the lowest resolution is on the second (in enable order)
controller, the first HDMI controller will end up with a smaller than
expected clock rate.
Since we don't really need an exact frequency there, we can simply change
the minimum rate we expect instead.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/821992209cc0d7a83254bf26fe2bf507ef0994d2.1599120059.git-series.maxime@cerno.tech
The HSM clock needs to be setup at around 101% of the pixel rate. This
was done previously by setting the clock rate to 163.7MHz at probe time and
only check in mode_valid whether the mode pixel clock was under the pixel
clock +1% or not.
However, with 4k we need to change that frequency to a higher frequency
than 163.7MHz, and yet want to have the lowest clock as possible to have a
decent power saving.
Let's change that logic a bit by setting the clock rate of the HSM clock
to the pixel rate at encoder_enable time. This would work for the
BCM2711 that support 4k resolutions and has a clock that can provide it,
but we still have to take care of a 4k panel plugged on a BCM283x SoCs
that wouldn't be able to use those modes, so let's define the limit in
the variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7e692ddc231d33dd671e70ea04dd1dcf56c1ecb3.1599120059.git-series.maxime@cerno.tech
The mode_valid hook on the encoder uses a pointer to a drm_encoder called
crtc, which is pretty confusing. Let's rename it to encoder to make it
clear what it is.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7fbabab03992efe4a3a3640ac5ee2bb49b1c7338.1599120059.git-series.maxime@cerno.tech
Similarly to the audio support, CEC support is not there yet for the
BCM2711, so let's skip entirely the CEC initialization through a variant
flag.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bd0c4afa83b4e121692352cdc2dd1886162c7552.1599120059.git-series.maxime@cerno.tech
The CEC init code was put directly into the bind function, which was quite
inconsistent with how the audio support was done, and would prevent us from
further changes to skip that initialisation entirely.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/21f4717e076291522d0784a7fd3774d8e97eaf01.1599120059.git-series.maxime@cerno.tech
The HDMI driver was registering a single debugfs file so far with the name
hdmi_regs.
Obviously, this is not going to work anymore when will have multiple HDMI
controllers since we will end up trying to register two files with the same
name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9505c1eb40b3ef3709277bf9e8af77917b249c32.1599120059.git-series.maxime@cerno.tech
The vc4 CRTC will use the encoder type to control its output clock
muxing. However, this will be different from HDMI0 to HDMI1, so let's
store our type in the variant structure so that we can support multiple
controllers later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2736a86b498551ba9dbc5803c5bb910627a2550c.1599120059.git-series.maxime@cerno.tech
Similarly to the previous patches, the timings setup in the HDMI controller
of the BCM2711 is slightly different, mostly because it supports higher
resolutions and thus needed more spaces for the various timings, resulting
in the register layout changing.
Let's add a callback for that as well.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0cfcbb379212f90b4abc76c0ccf3b90d1d7c0268.1599120059.git-series.maxime@cerno.tech
Similarly to the previous patches, the CSC setup is slightly different in
the BCM2711 than in the previous generations. Let's add a callback for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5c19bbf10153cb42ca0fb67e08606c8295c17236.1599120059.git-series.maxime@cerno.tech
The HDMI PHY in the BCM2711 HDMI controller is significantly more
complicated to setup than in the older BCM283x SoCs.
Let's add hooks to enable and disable the PHY.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7216826284dbc60a58bdacd662805d20699e5c80.1599120059.git-series.maxime@cerno.tech
The BCM2711 and BCM283x HDMI controllers use a slightly different reset
sequence, so let's add a callback to reset the controller.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a34bcb493da07eae58ed704f65e72ce0748e8952.1599120059.git-series.maxime@cerno.tech
The HDMI controllers found in the BCM2711 have most of the registers
reorganized in multiple registers areas and at different offsets than
previously found.
The logic however remains pretty much the same, so it doesn't really make
sense to create a whole new driver and we should share the code as much as
possible.
Let's implement some indirection to wrap around a register and depending on
the variant will lookup the associated register on that particular variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3070236daff920e7edd11c5a72ac31fd0f6a656b.1599120059.git-series.maxime@cerno.tech
The HDMI controllers found in the BCM2711 has a pretty different clock and
registers areas than found in the older BCM283x SoCs.
Let's create a variant structure to store the various adjustments we'll
need later on, and a function to get the resources needed for one
particular version.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/71cfa3ce3d865bbab52a0e5651bc052dc4893f11.1599120059.git-series.maxime@cerno.tech
The vc4_hdmi_connector was only used to switch between drm_connector to
drm_encoder. However, we can now use vc4_hdmi to do the switch, so that
structure is redundant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/aee5120728db350b19c074de4290eafaf01e6671.1599120059.git-series.maxime@cerno.tech
The unbind function needs to retrieve a vc4_hdmi structure pointer through
the struct device that we're given since we want to support multiple HDMI
controllers.
However, our optional ASoC support doesn't make that trivial since it will
overwrite the device drvdata if we use it, but obviously won't if we don't
use it.
Let's make sure the fields are at the proper offset to be able to cast
between the snd_soc_card structure and the vc4_hdmi structure
transparently so we can support both cases.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/717082cba06b5c06280f26c56c08aee512365ed3.1599120059.git-series.maxime@cerno.tech
Our CEC code also retrieves the associated vc4_hdmi by setting the
vc4_dev pointer as its private data, and then dereferences its vc4_hdmi
pointer.
In order to eventually get rid of that pointer, we can simply pass the
vc4_hdmi pointer directly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/cb575cb9e13018bce131b8535e5b572dc1027877.1599120059.git-series.maxime@cerno.tech
Whenever the code needs to access the vc4_hdmi structure from a DRM
connector or encoder, it first accesses the drm_device associated to the
connector, then retrieve the drm_dev private data which gives it a
pointer to our vc4_dev, and will finally follow the vc4_hdmi pointer in
that structure.
That will also give us some trouble when having multiple controllers,
but now that we have our encoder and connector structures that are part
of vc4_hdmi, we can simply call container_of on the DRM connector or
encoder and retrieve the vc4_hdmi structure directly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/536ecce5898ea75839fa3788b876009d69a5ccae.1599120059.git-series.maxime@cerno.tech
The function vc4_hdmi_connector_detect access its vc4_hdmi struct by
dereferencing the pointer in the structure vc4_dev. This will cause some
issues when we will have multiple HDMI controllers, so let's just use the
local variable for now instead of dereferencing that pointer all the time,
and we'll fix the local variable later.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/ef92c5582d3b2894128b2272a8ada7cbc20be3d9.1599120059.git-series.maxime@cerno.tech
The current driver only supports a single HDMI controller, and part of
the issue is that the main vc4_dev structure holds a pointer to its
(only) HDMI controller, and the HDMI registers accessors will use it to
retrieve the mapped addresses.
Let's modify those accessors to use directly the vc4_hdmi structure so
that we can eventually get rid of that single global pointer.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/886b955586264ce078d7d35e9b8ef9ae51675c27.1599120059.git-series.maxime@cerno.tech
The driver isn't consistent with the name given to the vc4_hdmi
structure pointer in its functions. Make sure to use a consistent name.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/696be840dc427245afe94b43e0b829c728d948a7.1599120059.git-series.maxime@cerno.tech
Now that we are passing the vc4_hdmi structure to the connector init
function, we can simply use the pointer in that structure instead of
having the pointer as an argument.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/4fe1b45fe45e4ba57d40154da010807d4e5db86c.1599120059.git-series.maxime@cerno.tech
the vc4_hdmi driver has some custom structures to hold the data it needs to
associate with the drm_encoder and drm_connector structures.
However, it allocates them separately from the vc4_hdmi structure which
makes it more complicated than it needs to be.
Move those structures to be contained by vc4_hdmi and update the code
accordingly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/93b418d63c876355af2b3d3afebe31a256268623.1599120059.git-series.maxime@cerno.tech
We're calling vc4_debugfs_add_file with our struct vc4_hdmi pointer set
in the private field, but we don't use that field and go through the
main struct vc4_dev to get it.
Let's use the private field directly, that will save us some trouble
later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/24028dc06c379dbc71f98e027cce2839fdd446ce.1599120059.git-series.maxime@cerno.tech
In order to prevent issues during the firmware to KMS transition, we need
to make sure the pixelvalve are disabled at boot time so that the DRM state
matches the hardware state.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/ad57f1bdeae7a99631713b0fc193c86f223de042.1599120059.git-series.maxime@cerno.tech
At boot time, if we detect that a pixelvalve has been enabled, we need to
be able to retrieve the HVS channel it has been assigned to so that we can
disable that channel too. Let's create that function that returns the FIFO
or an error from a given output.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/178192d90874559b8386139f2226e773347729fc.1599120059.git-series.maxime@cerno.tech
During the transition from the firmware to the KMS driver, we need to pay
particular attention to how we deal with the pixelvalves that have already
been enabled, otherwise either timeouts or stuck pixels can occur. We'll
thus need to call the function to stop an HVS channel at boot.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/a9d5f0891c3bc1deb6b16d56ca6994ed912ec7c7.1599120059.git-series.maxime@cerno.tech
Even though it's not really clear why we need to flush the PV FIFO during
the configuration even though we started by flushing it, experience shows
that without it we get a stale pixel stuck in the FIFO between the HVS and
the PV.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ccd6269ba37b2f849ba6e62471c99bd93a4548a0.1599120059.git-series.maxime@cerno.tech
In order to avoid a stale pixel getting stuck on mode change or a disable
/ enable cycle, we need to make sure to flush the PV FIFO on disable.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/26fe48b09d77088679ed0c8cb8cf0db2f108195e.1599120059.git-series.maxime@cerno.tech
In order to avoid pixels getting stuck in the (unflushable) FIFO between
the HVS and the PV, we need to add some delay after disabling the PV output
and before disabling the HDMI controller. 20ms seems to be good enough so
let's use that.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/15cf215bd2ceebd203c4010c09c21a4019c650ed.1599120059.git-series.maxime@cerno.tech
In the BCM2711, the setup of the HVS, pixelvalve and HDMI controller
requires very precise ordering and timing that the regular atomic callbacks
don't provide. Let's add new callbacks on top of the regular ones to be
able to split the configuration as needed.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1dd78efe8f29add73c97d0148cfd4ec8e34aaf22.1599120059.git-series.maxime@cerno.tech
In order to avoid stale pixels getting stuck in an intermediate FIFO
between the HVS and the pixelvalve on BCM2711, we need to configure the HVS
channel before the pixelvalve is reset and configured.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9d7c5a03bc1a1e6d50f7b617cc2d8a46a4bbb7bc.1599120059.git-series.maxime@cerno.tech
Since we moved the pixelvalve configuration to atomic_enable, we're now
first calling the function that resets the pixelvalve and then the one that
configures it.
However, the first thing the latter is doing is calling the reset function,
meaning that we reset twice our pixelvalve. Let's remove the first call.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a0a31af0d4a7a070de979f0e5b618d9e2c730e7f.1599120059.git-series.maxime@cerno.tech
On BCM2711 to avoid stale pixels getting stuck in intermediate FIFOs, the
pixelvalve needs to be setup each time there's a mode change or enable /
disable sequence.
Therefore, we can't really use mode_set_nofb anymore to configure it, but
we need to move it to atomic_enable.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f86c7a6946f98262f1cf59a461596a796d4bcc5f.1599120059.git-series.maxime@cerno.tech
In order to clear our intermediate FIFOs that might end up with a stale
pixel, let's make sure our FIFO channel is reset every time our channel is
setup.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b34c562b36177c758dd2e9d84bceb07689bfbe05.1599120059.git-series.maxime@cerno.tech
Since most of the HVS channel is setup in the init function, let's move the
gamma setup there too. As this makes the HVS mode_set function empty, let's
remove it in the process.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d439da8f1592a450a6ad35ab1f9e77def17c7965.1599120059.git-series.maxime@cerno.tech
Now that we only configure the PixelValve in vc4_crtc_config_pv, it doesn't
really make much sense to dump its register content in its caller.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c195af7d9e140a2a6db32992ee7e54071c6f94ba.1599120059.git-series.maxime@cerno.tech
The driver resets the pixelvalve FIFO in a number of occurences without
always using the same sequence.
Since this will be critical for BCM2711, let's move that sequence to a
function so that we are consistent.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/fb31003a9eee02c4b949556299ff41f0a113499a.1599120059.git-series.maxime@cerno.tech
The previous generations were only supporting a single HDMI controller, but
that's about to change, so put an index as well to differentiate between
the two controllers.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/84e11e4793aaa30d6e5c56e305d22404ac5a932d.1599120059.git-series.maxime@cerno.tech
The longer FIFOs in vc5 pixelvalves means that the FIFO full level
doesn't fit in the original register field and that we also have a
secondary field. In order to prepare for this, let's move the registers
fill part to a helper function.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/e46a3823128af50c1c833de8fa9b95e9b86c2f66.1599120059.git-series.maxime@cerno.tech
Not all pixelvalve FIFOs in vc5 have the same depth, so we need to add that
to our vc4_crtc_data structure to be able to compute the fill level
properly later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/7df3549c1bea9b0a27c784dc416bb9a831e4e18f.1599120059.git-series.maxime@cerno.tech
The HVS found in the BCM2711 has 6 outputs and 3 FIFOs, with each output
being connected to a pixelvalve, and some muxing between the FIFOs and
outputs.
Any output cannot feed from any FIFO though, and they all have a bunch of
constraints.
In order to support this, let's store the possible FIFOs each output can be
assigned to in the vc4_crtc_data, and use that information at atomic_check
time to iterate over all the CRTCs enabled and assign them FIFOs.
The channel assigned is then set in the vc4_crtc_state so that the rest of
the driver can use it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f9aba3814ef37156ff36f310118cdd3954dd3dc5.1599120059.git-series.maxime@cerno.tech
The vc4 atomic commit loop has an handrolled loop that is basically
identical to for_each_new_crtc_state, let's convert it to that helper.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a712d2b70aaee20379cfc52c2141aa2f6e2a9d5b.1599120059.git-series.maxime@cerno.tech
The VIDEN bit in the pixelvalve currently being used to enable or disable
the pixelvalve seems to not be enough in some situations, which whill end
up with the pixelvalve stalling.
In such a case, even re-enabling VIDEN doesn't bring it back and we need to
clear the FIFO. This can only be done if the pixelvalve is disabled though.
In order to overcome this, we can configure the pixelvalve during
mode_set_no_fb by calling vc4_crtc_config_pv, but only enable it in
atomic_enable and flush the FIFO there, and in atomic_disable disable the
pixelvalve again.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e97596f62f4df83424d994a23465463ac60f986e.1599120059.git-series.maxime@cerno.tech
The vc4_crtc_handle_page_flip already has a local variable holding the
value of vc4_crtc->channel, so let's use it instead.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/439c589baec72ddb89159857a2d078fdd77b02a2.1599120059.git-series.maxime@cerno.tech
In vc5, the HVS has 6 outputs and 3 FIFOs (or channels), with
pixelvalves each being assigned to a given output, but each output can
then be muxed to feed from multiple FIFOs.
Since vc4 had that entirely static, both were probably equivalent, but
since that changes, let's rename hvs_channel to hvs_output in the
vc4_crtc_data, since a pixelvalve is really connected to an output, and
not to a FIFO.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b7618bb17b1c435c5d6ce50bcde2fe9243281d02.1599120059.git-series.maxime@cerno.tech
The COB allocation depends on the HVS channel used for a given
pixelvalve.
While the channel allocation was entirely static in vc4, vc5 changes
that and at bind time, a pixelvalve can be assigned to multiple
HVS channels.
Let's prepare that rework by allocating the COB when it's actually
needed.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/484cbd4b00cfeee425295df438222258cc39a3dd.1599120059.git-series.maxime@cerno.tech
Some of the HDMI pixelvalves in vc5 output two pixels per clock cycle.
Let's put the number of pixel output per clock cycle in the CRTC data and
update the various calculations to reflect that.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/18a3bb079981ba820132b37e736a4bb371234d2e.1599120059.git-series.maxime@cerno.tech
Let's now create more planes that can be affected to all the CRTCs.
vc4 has 3 CRTCs, 1 primary and 1 cursor each, and was having 24 (8
planes per CRTC) overlays.
However, vc5 has 5 CRTCs, so keeping the same logic would put us at 50
planes which is well above the 32 planes limit imposed by DRM.
Using 16 seems like a good tradeoff between staying under 32 and yet
providing enough planes.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/b41003001541fc2bb23668c699c0369ff7983be8.1599120059.git-series.maxime@cerno.tech
The current code is using the maximum of the source line size and the
destination line size to compute the size of the LBM to allocate.
While this is simpler, it starts to be an issue with modes such as 4k with
a quite long that will consume all the available memory, so we no longer
have that luxury.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b9e091883a4f7395c5b6a4f7c6070225934293db.1599120059.git-series.maxime@cerno.tech
In order to prevent timeouts and stalls in the pipeline, the core clock
needs to be maxed at 500MHz during a modeset on the BCM2711.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/37ed9e0124c5cce005ddc8dafe821d8b0da036ff.1599120059.git-series.maxime@cerno.tech
The HVS found in the BCM2711 is slightly different from the previous
generations.
Most notably, the display list layout changes a bit, the LBM doesn't have
the same size and the formats ordering for some formats is swapped.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1d02fab3b916d639c2dc05608c117bbd8230ebe8.1599120059.git-series.maxime@cerno.tech
Add support for the video pattern generator (VPG) BER pattern mode and
configuration in runtime.
This enables using the debugfs interface to manipulate the VPG after
the pipeline is set.
Also, enables the usage of the VPG BER pattern.
Changes in v2:
- Added VID_MODE_VPG_MODE
- Solved incompatible return type on __get and __set
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Adrian Pop <pop.adrian61@gmail.com>
Signed-off-by: Angelo Ribeiro <angelo.ribeiro@synopsys.com>
Tested-by: Yannick Fertre <yannick.fertre@st.com>
Tested-by: Adrian Pop <pop.adrian61@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a809feb7d7153a92e323416f744f1565e995da01.1586180592.git.angelo.ribeiro@synopsys.com
Current code enables the HS clock when video mode is started or to
send out a HS command, and disables the HS clock to send out a LP
command. This is not what DSI spec specify.
Enable HS clock either in command and in video mode.
Set automatic HS clock management for panels and devices that
support non-continuous HS clock.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701194234.18123-1-yannick.fertre@st.com
Current code does not properly computes the max length of LP
commands that can be send during H or V sync, and rely on static
values.
Limiting the max LP length to 4 byte during the V-sync is overly
conservative.
Relax the limit and allows longer LP commands (16 bytes) to be
sent during V-sync.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701143131.841-1-yannick.fertre@st.com
Current code only sends LP commands in command mode.
Allows sending LP commands also in video mode by setting the
proper flag in DSI_VID_MODE_CFG.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708140836.32418-1-yannick.fertre@st.com
The upstream S6E63M0 driver has some peculiarities around
the prepare/enable disable/unprepare sequence: the screen
is taken out of sleep in prepare() as part of
s6e63m0_init() the put to on with MIPI_DCS_SET_DISPLAY_ON
in enable().
However it is just put into sleep mode directly in
disable(). As disable()/enable() can be called without
unprepare()/prepare() being called, this is unbalanced,
we should take the display out of sleep in enable()
then turn it off().
Further MIPI_DCS_SET_DISPLAY_OFF is never called
balanced with MIPI_DCS_SET_DISPLAY_ON.
The vendor driver for Samsung GT-I8190 (Golden) does all
of these things in strict order.
Augment the driver to do exit sleep/set display on in
enable() and set display off/enter sleep in disable().
Further send an explicit reset pulse in power_on() so we
come up in a known state, and issue the MCS_ERROR_CHECK
command after setting display on like the vendor driver
does. Also use the timings from the vendor driver in
the sequence.
Doing all of these things makes the display much more
stable on the Samsung GT-I8190 when enabling/disabling
the display pipeline.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200817213906.88207-1-linus.walleij@linaro.org
We add code to identify a few different panels mounted
on the s6e63m0 controller. This is necessary to achieve
the proper biasing with DSI versions of the panel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200809215104.1830206-5-linus.walleij@linaro.org
This adds code to send read commands to read a single
byte from the display, in order to perform MTP ID
look-up of the mounted panel on the s6e63m0 controller.
This is needed for proper biasing on the DSI variants.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200809215104.1830206-4-linus.walleij@linaro.org
This makes it possible to use the s6e63m0 panel with a
DSI host, such as in the Samsung GT-I8190 (Golden) mobile
phone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200809215104.1830206-3-linus.walleij@linaro.org
This panel can be accessed using both SPI and DSI.
To make it possible to probe and use the device also from
a DSI bus, first break out the SPI support to its own file.
Since all the panel driver does is write DCS commands to
the panel, we pass a DCS write function to probe()
from each subdriver.
We make the Kconfig entry for SPI mode default so all
current users will continue to work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/384873/
Following functions are only used internally, not by drivers:
- devm_drm_dev_init
Also, now that we have a very slick and polished way to allocate a
drm_device with devm_drm_dev_alloc, update all the docs to reflect the
new reality. Mostly this consists of deleting old and misleading
hints. Two main ones:
- it is no longer required that the drm_device base class is first in
the structure. devm_drm_dev_alloc can cope with it being anywhere
- obviously embedded now strongly recommends using devm_drm_dev_alloc
v2: Fix typos (Noralf)
v3: Split out the removal of drm_dev_init, that's blocked on some
discussions on how to convert vgem/vkms/i915-selftests. Adjust commit
message to reflect that.
Cc: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org> (v2)
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Luben Tuikov <luben.tuikov@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200902072627.3617301-1-daniel.vetter@ffwll.ch
That is not used any more.
v2: keep the NULL checks in TTM.
v3: remove unused variable
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/388646/
While working on TTM cleanups I've found that the io_reserve_lru used by
Nouveau is actually not working at all.
In general we should remove driver specific handling from the memory
management, so this patch moves the io_reserve_lru handling into Nouveau
instead.
v2: don't call ttm_bo_unmap_virtual in nouveau_ttm_io_mem_reserve
v3: rebased and use both base and offset in the check
v4: fix small typos and test the patch
v5: rebased and keep the mem.bus init in TTM.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/388643/
We are trying to remove the io_lru handling and depend
on zero init base, offset and addr here.
v2: init addr as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/388642/
When going through a disable/enable cycle without changing the
framebuffer the optimization added by commit 3954ff10e0 ("drm/virtio:
skip set_scanout if framebuffer didn't change") causes the screen stay
blank. Add a bool to force an update to fix that.
v2: use drm_atomic_crtc_needs_modeset() (Daniel).
Cc: 1882851@bugs.launchpad.net
Fixes: 3954ff10e0 ("drm/virtio: skip set_scanout if framebuffer didn't change")
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Jiri Slaby <jirislaby@kernel.org>
Tested-by: Diego Viola <diego.viola@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20200818072511.6745-2-kraxel@redhat.com
The only usage of these is to assign their address to the fbops field in
the fb_info struct, which is a const pointer. Make them const to allow
the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200830211741.17326-1-rikard.falkeborn@gmail.com
In order to shrink drm_display_mode below the magic two cacheline
mark in 64bit we need to shrink it by another 8 bytes. The easiest
thing to eliminate is the 'export_head' list head which is only
used during the getconnector ioctl to temporarly track which modes
on the connector's mode list are to be exposed and which are to
remain hidden.
We can simply replace the list head with a boolean which we use
to tag the modes that are to be exposed. If we make sure to clear
the tags after we're done with them we don't even need an extra
loop over the modes to reset the tags at the start of the
getconnector ioctl.
Conveniently we already have a hole for the boolean left
behind by the removal of mode->private_flags. The final size
of the struct is now 112 bytes on 32bit and 120 bytes on 64bit.
Another alternative would be a temp bitmask so we wouldn't have
to have anything in the mode struct itself. The main issue is
how large of a bitmask do we need? I guess we could allocate
it dynamically but that means an extra kcalloc() and an extra
loop through the modes to count them first (or grow the bitmask
with krealloc() as needed).
CC: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-17-ville.syrjala@linux.intel.com
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
For DP MST outputs, the i2c device currently only supports transfers
that can be implemented using remote i2c reads. Such transfers must
consist of zero or more write transactions followed by one read
transaction. DDC/CI commands require standalone write transactions and
hence aren't supported.
Since each remote i2c write is handled as a separate transfer, remote
i2c writes can support transfers consisting of write transactions, where
all but the last have I2C_M_STOP set. According to the DDC/CI 1.1
standard, DDC/CI commands only require a single write or read
transaction in a transfer, so this is sufficient.
For i2c transfers meeting the above criteria, generate and send a remote
i2c write message for each transaction. Add the trivial remote i2c write
reply parsing support so remote i2c write acks bubble up correctly.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/37
Signed-off-by: Sam McNally <sammc@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727160225.1.I4e95a534de051551cd143e6cb83d4c5a9b0ad1cd@changeid
When verify_crc_source() fails, source needs to be freed.
However, current code is returning directly and ends up
leaking memory.
Fixes: d5cc15a0c6 ("drm: crc: Introduce verify_crc_source callback")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[danvet: change Fixes: tag per Laurent's review]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819082228.26847-1-dinghao.liu@zju.edu.cn
The VKMS blend function was ignoring the alpha channel and just
overwriting vaddr_src with vaddr_dst. This XRGB approach triggers a
warning when running the kms_cursor_crc/cursor-alpha-transparent test
case. In IGT, cairo_format_argb32 uses premultiplied alpha (according to
documentation). Also current DRM assumption is that alpha is
premultiplied. Therefore, this patch considers premultiplied alpha
blending eq to compose vaddr_src with vaddr_dst.
This change removes the following cursor-alpha-transparent warning:
"Suspicious CRC: All values are 0."
V2:
- static for local functions
- const for the read-only variable argb_src
- replaces variable names
- drops unnecessary comment
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200825114532.abzdooluny2ekzvm@smtp.gmail.com
The OrtusTech COM43H4M85ULC panel is a 18-bit RGB panel. Commit
f098f168e9 ("drm: panel: Fix bus format for OrtusTech COM43H4M85ULC
panel") has fixed the bus formats, but forgot to address the bpc value.
Set it to 6.
Fixes: f098f168e9 ("drm: panel: Fix bus format for OrtusTech COM43H4M85ULC panel")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200824003254.21904-1-laurent.pinchart@ideasonboard.com
DSI end-points are supposed to be at node 0 and node 1 as per binding.
So fix this and use node 0 and node 1 for dsi.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 23278bf54a ("drm/bridge: Introduce LT9611 DSI to HDMI bridge")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200828074251.3788165-1-vkoul@kernel.org
Maxime Ripard