forcewake is controlled by the open and close of the debugfs file. This
assures that buggy applications cannot cause the GT to stay on forever.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The render P-state handling code requires reading from a GT register.
This means that FORCEWAKE must be written to, a resource which is shared
and should be protected by struct_mutex. Hence we can not manipulate
that register from within the interrupt handling and so must delegate
the task to a workqueue.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Found by the new strict checking for the mutex being held whilst
manipulating the forcewake status.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Provide a reference count to track the forcewake state of the GPU and
give a safe mechanism for userspace to wake the GT. This also potentially
saves a UC read if the GT is known to be awake already.
The reference count is atomic, but the register access and hardware wake
sequence is protected by struct_mutex.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Moved the macros around to properly do reads and writes for the given
GPU. This is to address special requirements for gen6 (SNB) reads and
writes.
Registers in the range 0-0x40000 on gen6 platforms require special
handling. Instead of relying on the callers to pick the registers
correctly, move the logic into the read and write functions.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the outputs are active and continuing to access the GATT when we
teardown the PTEs, then there is a potential for us to hang the GPU.
The hang tends to be a PGTBL_ER with either an invalid host access or
an invalid display plane fetch.
v2: Reorder IRQ initialisation to defer until after GEM is setup.
Reported-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch> (855GM)
Tested-by: Pekka Enberg <penberg@kernel.org>
# note that this doesn't fix the underlying problem of the
PGTBL_ER and pipe underruns being reported immediately upon
init on his 965GM MacBook
Reported-and-tested-by: Rick Bramley <richard.bramley@hp.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35635
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36048
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Rely on the GPU snooping into the CPU cache for appropriately bound
objects on MI_FLUSH. Or perhaps one day we will have a cache-coherent
CPU/GPU package...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
... to clarify just how we use it inside the driver and remove the
confusion of the poorly matching agp_type names. We still need to
translate through agp_type for interface into the fake AGP driver.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Currently this is only useful for the rc6 stuff. But this would also be
useful when I finally get around to the logical context + ppgtt stuff.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
For debug & testing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There is a race condition between setting PWRCTXA and executing
MI_SET_CONTEXT. PWRCTXA must not be set until a valid context has been
written (or else the GPU could possible go into rc6, and return to an
invalid context).
Reported-and-Tested-by: Gu Rui <chaos.proton@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28582
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Added a new function which waits for the ringbuffer space to be equal to
(total - 8). This is the empty condition of the ringbuffer, and
equivalent to head==tail.
Also modified two users of this functionality elsewhere in the code.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In the failure cases during rc6 initialization, both the power context
and render context may get !refcount without holding struct_mutex.
However, on rc6 disabling, the lock is held by the caller.
Rearranged the locking so that it's safe in both cases.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
They're used in one place, and not providing any descriptive value,
with their names just being approximately the conjunction of the
struct name and the struct field.
This diff was produced with gcc -E, copying the new struct definitions
out, moving a couple of the old comments into place in the new
structs, and reindenting.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We used to have these from the product of (pch, non-pch) * (pipe a,
pipe b). Now we can just use the nice per-pipe reg macros in the
split out crtc_mode_sets.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While g4x had DP, eDP came with Ironlake, so we don't need that code here.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This path, which shouldn't be *that* complicated, is now so littered
with per-chipset tweaks that it's hard to trace the order of what
happens. HAS_PCH_SPLIT() is the most radical change across chipsets,
so it seems like a natural split to simplify the code.
This first commit just copies the existing code without changing
anything.
v2: updated to track removal of call to intel_enable_plane from i9xx_crtc_mode_set
Signed-off-by: Eric Anholt <eric@anholt.net>
Hella-acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to ensure that we feed valid memory into the display plane
attached to the pipe when switching the pipe on. Otherwise, the display
engine may read through an invalid PTE and so throw an PGTBL_ER
exception.
As we need to perform load detection before even the first object is
allocated for the fbdev, there is no pre-existing object large enough
for us to borrow to use as the framebuffer. So we need to create one
and cleanup afterwards. At other times, the current fbcon may be large
enough for us to borrow it for duration of load detection.
Found by assert_fb_bound_for_plane().
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we now never attempt to steal a crtc for load detection, we either
set a mode on a new pipe, or change the dpms mode on an existing pipe.
Never both, so we can simplify the code slightly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we only allow the use of a disabled CRTC, we don't need to handle the
case where we are reusing an already enabled pipe.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and the no longer relevant comment. The code ceased stealing a pipe
for load detection a long time ago.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keep all the state required for undoing and restoring the previous pipe
configuration together in a single struct passed from
intel_get_load_detect_pipe() to intel_release_load_detect_pipe() rather
than stuffing them inside the common encoder structure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Check the return value from drm_crtc_set_mode(), report the failure
via a debug message and propagate the error back to the caller. This
prevents us from blissfully continuing to do the load detection on a
disabled pipe. Fortunately actual failure for modesetting is very rare,
and reported failures even rarer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and so remove the confusion as to whether to use the returned crtc
or intel_encoder->base.crtc with the subsequent load-detection. Even
though they were the same, the two instances of load-detection code
disagreed over which was the more correct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Required so that we don't obliterate the queue if initialising the
rings after the global IRQ handler is installed.
[Jesse, you recently looked at refactoring the IRQ installation
routines, does moving the initialisation of ring buffer data structures away
from that routine make sense in your grand scheme?]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
If we're using vga switcheroo, the device may be turned off
and poking it can return random state. This provokes an OOPS fixed
separately by 8ff887c847 (drm/i915/dp: Be paranoid in case we disable a
DP before it is attached). Trying to use and respond to events on a
device that has been turned off by the user is in principle a silly thing
to do.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Despite the fixes in 548f245ba6 (drm/i915: fix per-pipe reads after
"cleanup"), we missed one neighbouring read that was mistakenly replaced
with the reg value in 9db4a9c (drm/i915: cleanup per-pipe reg usage).
This was preventing us from correctly determining the mode the BIOS left
the panel in for machines that neither have an OpRegion nor access to
the VBT, (e.g. the EeePC 700).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
When enabling the plane, it is helpful to have already pointed that
plane to valid memory or else we may incur the wrath of a PGTBL_ER.
This code preserved the behaviour from the bad old days for unknown
reasons...
Found by assert_fb_bound_for_plane().
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Given that the hardware may be left in a random condition by the BIOS,
it is conceivable that we then attempt to clear the DP_PIPEB_SELECT bit
without us ever enabling/attaching the DP encoder to a pipe. Thus
causing a NULL deference when we attempt to wait for a vblank on that
crtc.
Reported-and-tested-by: Bryan Christ <bryan.christ@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36314
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36456
Reported-and-tested-by: Bo Wang <bo.b.wang@intel.com>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix gart setup on fusion parts (v2)
drm: Send pending vblank events before disabling vblank.
drm/radeon: fix regression on atom cards with hardcoded EDID record.
drm/radeon/kms: add some new pci ids
Out of the entire GART/VM subsystem, the hw designers changed
the location of 3 regs.
v2: airlied: add parameter for userspace to work from.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is the least-bad behaviour. It means that we signal the
vblank event before it actually happens, but since we're disabling
vblanks there's no guarantee that it will *ever* happen otherwise.
This prevents GL applications which use WaitMSC from hanging
indefinitely.
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since fafcf94e2b introduced an edid size, it seems to have broken this path.
This manifest as oops on T500 Lenovo laptops with dual graphics primarily.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=33812
cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In particular, s_freeing_list needs to be initialized early, since it is
used on some of the error paths when mounts fail. The mapping inode,
for example, would be initialized and then free'd on an error path
before s_freeing_list was initialized, but the inode drop operation
needs the s_freeing_list to be set up.
Normally you'd never see this, because not only is logfs fairly rare,
but a successful mount will never have any issues.
Reported-by: werner <w.landgraf@ru.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'stable/bug-fixes-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mask_rw_pte mark RO all pagetable pages up to pgt_buf_top
xen/mmu: Add workaround "x86-64, mm: Put early page table high"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wm831x-ts - move BTN_TOUCH reporting to data transfer
Input: wm831x-ts - allow IRQ flags to be specified
Input: wm831x-ts - fix races with IRQ management
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
sysctl: net: call unregister_net_sysctl_table where needed
Revert: veth: remove unneeded ifname code from veth_newlink()
smsc95xx: fix reset check
tg3: Fix failure to enable WoL by default when possible
networking: inappropriate ioctl operation should return ENOTTY
amd8111e: trivial typo spelling: Negotitate -> Negotiate
ipv4: don't spam dmesg with "Using LC-trie" messages
af_unix: Only allow recv on connected seqpacket sockets.
mii: add support of pause frames in mii_get_an
net: ftmac100: fix scheduling while atomic during PHY link status change
usbnet: Transfer of maintainership
usbnet: add support for some Huawei modems with cdc-ether ports
bnx2: cancel timer on device removal
iwl4965: fix "Received BA when not expected"
iwlagn: fix "Received BA when not expected"
dsa/mv88e6131: fix unknown multicast/broadcast forwarding on mv88e6085
usbnet: Resubmit interrupt URB if device is open
iwl4965: fix "TX Power requested while scanning"
iwlegacy: led stay solid on when no traffic
b43: trivial: update module info about ucode16_mimo firmware
...
ctl_table_headers registered with register_net_sysctl_table should
have been unregistered with the equivalent unregister_net_sysctl_table
Signed-off-by: Lucian Adrian Grijincu <lucian.grijincu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keith Packard