Specify whether we are only performing the context setup portion of the
'address device' command, or the full operation issuing 'SetAddress'
on the wire.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch should fix the below compile warning:
drivers/usb/storage/protocol.c: In function 'usb_stor_access_xfer_buf':
drivers/usb/storage/protocol.c:155:22: warning: comparison of distinct
pointer types lacks a cast [enabled by default]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch correctly sets the dwNumOfPackets field of the HWA transfer
request for isochronous transfers with multiple segments. Previously
all segments used the value that was set for the first segment which may
not be correct.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If multiple segments belonging to an isoc transfer are submitted
concurrently, the isoc_frame_index field in struct wa_xfer can get
corrupted. This patch moves the isoc_frame_index field from struct
wa_xfer to struct wa_seg to prevent this from happening.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use USB_CTRL_SET_TIMEOUT and USB_CTRL_GET_TIMEOUT for USB control
messages instead of an arbitrary 1s timeout value. This is particularly
useful for WUSB since in the worst case RF scanario, a WUSB device can
be unresponsive for up to 4s and still be connected.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to skip querying the config and string descriptors for
unauthorized WUSB devices when usb_new_device is called. It is allowed
by WUSB spec. The only action that needs to be delayed until
authorization time is the set config. This change allows user mode
tools to see the config and string descriptors earlier in enumeration
which is needed for some WUSB devices to function properly on Android
systems. It also reduces the amount of divergent code paths needed
for WUSB devices.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usb_submit_urb, do not fail if an isoc URB for a wireless USB device
has an interval < 6. Per WUSB spec, isoc endpoints can support values
from 1-16. Valid values for interrupt URBs for wireless USB devices are
still 6-16.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a URB is broken up into multiple transfer segments and a short
transfer occurs in any segment other than the last, the URB will
currently get stuck in the driver forever. This patch adds a check for
a short transfer and cleans up any pending segments so the URB can
complete properly.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 614ced91fc.
The units on this was seen were prototypes and the issue is
not seen on younger units.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Individual controller driver has different requirement for wakeup
setting, so move it from core to itself. In order to align with
current etting the default wakeup setting is enabled (except for
chipidea host).
Pass compile test with below commands:
make O=outout/all allmodconfig
make -j$CPU_NUM O=outout/all drivers/usb
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX51 as the next user of the usbmisc driver.
Functionality is similar to i.MX53, so at this stage simply
reuse existing i.MX53 calls.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX27 and i.MX31 as the next user of the usbmisc driver.
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ci_hdrc_imx's probe needs usbmisc_imx to be loadded beforehand,
so it is better we load usbmisc_imx first.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap only needs to reallocate if the hw_read on the CAP register shows
lpm is used. Therefore the if() statement check the change.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use PCI standard marco dev_is_pci() instead of directly compare
pci_bus_type to check whether it is pci device.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use PCI standard marco dev_is_pci() instead of directly compare
pci_bus_type to check whether it is pci device.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds external USB phy support to USB HCD driver that
allows to find and initialize external USB phy, bound to
the HCD, when the HCD is added.
The usb_add_hcd function returns -EPROBE_DEFER if the USB
phy, bound to the HCD, is not ready.
If no USB phy is bound, the HCD is initialized as usual.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds remove_phy flag to the HCD structure. If the flag is
set and if hcd->phy is valid, the phy is shutdown and released
whenever usb_add_hcd fails or usb_hcd_remove is called.
This can be used by the HCD drivers to auto-remove
the external USB phy when it is no longer needed.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have sg_miter_* APIs for accessing scsi sg buffer, so
use them to make code clean and bug free.
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sg_copy_buffer() can't meet demand for some drrivers(such usb
mass storage), so we have to use the sg_miter_* APIs to access
sg buffer, then need export sg_miter_skip() for these drivers.
The API is needed for converting to sg_miter_* APIs in USB storage
driver for accessing sg buffer.
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add more info to debug prints in urb_unlink path
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add calls to usb_hcd_link_urb_to_ep, usb_hcd_unlink_urb_from_ep, and
usb_hcd_check_unlink_urb in the appropriate locations.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-spear glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-spear suspend scenario.
Calling explicitly the ohci_suspend() routine in
spear_ohci_hcd_drv_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-exynos glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-exynos suspend scenario.
Calling explicitly the ohci_suspend() routine in
exynos_ohci_suspend() will ensure proper handling of suspend
scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-da8xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-da8xx suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_da8xx_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.or
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-s3c2410 glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-s3c2410 suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_hcd_s3c2410_drv_suspend() will ensure
proper handling of suspend scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-at91 glue was not properly handled
as it was not suspending generic part of ohci controller. Alan Stern
suggested, properly handle ohci-at91 suspend scenario.
Calling explicitly the ohci_suspend() routine in ohci_hcd_at91_drv_suspend()
will ensure proper handling of suspend scenario. This task is sugested
by Alan Stern.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of OHCI was not properly
handled in ochi_suspend()routine. Alan Stern
suggested, properly handle OHCI suspend scenario.
This does generic proper handling of suspend
scenario to all OHCI SOC.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit "usb: usbtest: support bos descriptor test for usb 3.0"
introduced a test for bos descriptor. And USB 2.1 device also can be
checked. So this patch extends the test coverage to support USB 2.1 device.
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.1 Link PM adds to use bits[1:15] according to USB 2.0 ECN Errata for
Link Power Management spec.
Bit Encoding
0 Reserved
1 LPM
2 BESL & Altemate HIRD definitions supported
3 Recommended Baseline BESL valid
4 Recommended Deep BESL valid
11:8 Recommended Baseline BESL value
15:12 Recommended Deep BESL value
31:16 Reserved
So fix the bit mask from 0x1e to 0xfffe.
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 10 of usbtest module, it queues multiple control messages and
thereby tests control message queuing, protocol stalls, short reads, and
fault handling. And this patch add a test case to support queue BOS control
request for USB 3.0 SPEC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/host/ehci-mv.c:181:26-27: WARNING comparing pointer to 0, suggest !E
/c/kernel-tests/src/cocci/drivers/usb/host/ehci-mv.c:181:26-27: WARNING comparing pointer to 0
Compare pointer-typed values to NULL rather than 0
Semantic patch information:
This makes an effort to choose between !x and x == NULL. !x is used
if it has previously been used with the function used to initialize x.
This relies on type information. More type information can be obtained
using the option -all_includes and the option -I to specify an
include path.
Generated by: coccinelle/null/badzero.cocci
CC: Jingoo Han <jg1.han@samsung.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the drivers that no longer need it, it is removed.
It is removed from the Makefile. Drivers not fully converted
to dynamic debug have it shifted down into the individual
drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With dynamic debugging this log level is no longer supported.
The decision which messages are interesting is done in user space.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows removal of much conditional compilation.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a step in the conversion to only use dynamic
debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That logging is overkill. Simply remove it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These helpers are used only during setup of a HCD.
A small overhead is no problem.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes sure the header files are all there
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow a full switch to dynamic debugging make the
debug parameter conditional on defined(DEBUF) || defined(CONFIG_DYNAMIC_DEBUG)
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets rid of conditional compilation.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The decision what is interesting is shifted to user space by
dynamic debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams