send_packet() is used during initialization, before send_packet_delay
is set. So, move ictx->send_packet_delay to happen earlier.
[mchehab@redhat.com: fold two patches into one to make git history clearer]
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix mceusb_cmdsize() which returns incorrect datasize=0 for
sub-commands MCE_RSP_GETPORTSTATUS, MCE_RSP_GETWAKESOURCE,
MCE_RSP_EQDEVDETAILS, MCE_RSP_EQEMVER, and MCE_RSP_EQIRNUMPORTS.
While here, change mceusb_cmdsize() name to reflect that it returns
data size not cmd size.
Signed-off-by: William Steidtmann <billstei@hbci.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is very similar than rc-msi-digivox-iii but new keytable is needed
as there is one existing scancode mapped to different button. Also that
one has less buttons.
NEC extended protocol with address 0x61d6.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument, the subsequently
call to rc_free_device() on the same variable will cause a double
free bug. Fix by set argument to NULL, thus when fall through to
rc_free_device(), nothing will be done there.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument, the subsequently
call to rc_free_device() on the same variable will cause a double
free bug. Fix by set argument to NULL, thus when fall through to
rc_free_device(), nothing will be done there.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument, the subsequently
call to rc_free_device() on the same variable will cause a double
free bug. Fix by set argument to NULL, thus when fall through to
rc_free_device(), nothing will be done there.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument, the subsequently
call to rc_free_device() on the same variable will cause a double
free bug. Fix by set argument to NULL, thus when fall through to
rc_free_device(), nothing will be done there.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc_unregister_device already calls rc_free_device to free the passed
device. But in one of ttusbir's probe fail paths, we call
rc_unregister_device _and_ rc_free_device. This is wrong and results
in a double free.
Instead, set rc to NULL resulting in rc_free_device being a noop.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into patchwork
Linux 3.9-rc5
* tag 'v3.9-rc5': (1080 commits)
Linux 3.9-rc5
Revert "lockdep: check that no locks held at freeze time"
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
PNP: List Rafael Wysocki as a maintainer
rbd: don't zero-fill non-image object requests
ia64 idle: delete stale (*idle)() function pointer
Btrfs: don't drop path when printing out tree errors in scrub
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
Revert "mm: introduce VM_POPULATE flag to better deal with racy userspace programs"
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
mg_disk: fix error return code in mg_probe()
Btrfs: fix wrong return value of btrfs_lookup_csum()
Btrfs: fix wrong reservation of csums
Btrfs: fix double free in the btrfs_qgroup_account_ref()
Btrfs: limit the global reserve to 512mb
Btrfs: hold the ordered operations mutex when waiting on ordered extents
Btrfs: fix space accounting for unlink and rename
Btrfs: fix space leak when we fail to reserve metadata space
...
store_protocols() treats dev->rc_map.rc_type as a bitmap which is wrong for
two reasons. First of all, it is pretty bogus to change the protocol type of
the keymap just because the hardware has been asked to decode a different
protocol.
Second, dev->rc_map.rc_type is an enum (i.e. a single protocol) as pointed
out by James Hogan <james.hogan@imgtec.com>.
Fix both issues by introducing a separate enabled_protocols member to
struct rc_dev.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some imon devices (like 15c2:0036) need a higher delay between
send_packet calls.
Default value is still 5ms to avoid regressions on already working
hardware.
Also use interruptible wait to avoid load average going too high (and
let caller handle signals).
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The name is already misleading and will be more so in the future as the
connection to the input subsystem is obscured away further.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc-core is a subsystem so it should be registered earlier if built into the
kernel.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stead of doing a memcpy from #defined offset, declare structs which
describe the incoming and outgoing data accurately.
Tested on first generation RedRat.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The redrat hardware cannot handle periods of larger than 32767us,
limit appropriately. Also fix memory leak in redrat3_get_timeout.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver can be enabled on OMAP1 at the moment, which breaks
allyesconfig for that platform. Let's mark it OMAP2PLUS-only
in Kconfig, since that is the only thing it builds on.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Similarly probe() methods should not be marked __init unless
platform_driver_probe() is used.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
file argument is a struct file being passed to ->open() or
already opened; none of the checks in lirc_get_pdata()
can fail.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
This patch adds device tree parsing for gpio_ir_recv platform_data and
the mandatory binding documentation. It basically follows what we already
have for e.g. gpio_keys. All required device tree properties are OS
independent but an optional property allows linux specific support for rc
maps.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Smatch complains that "cmdbuf[cmdcount - length]" might go past the end
of the array. It's an easy warning to silence by moving the limit
check earlier.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If more than 127 different lengths are transmitted then the driver causes
an overrun on sample_lens. Try to send as much as possible and return the
amount sent.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This transceiver expects the set IR TX ports and IR data as seperate
packets, like the Windows driver does. Remove unnecessary kzalloc.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The GET_REVISION command puts the device in an unresponsive state,
although it continues to report any IR activity. Note that GET_REVISION
command is not documented, nor is any possible response to it parsed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On cold boot the device does not initialize until the first packet is
received, and that packet is not processed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A sample resolution of 2us generates more than 300 interrupts per key
and this resolution is not needed unless carrier reports are enabled.
Revert to a resolution of 10us unless carrier reports are needed. This
generates up to a fifth of the interrupts.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Events for the iMon Knob pad where not correctly interpreted on ARM,
resulting in buggy mouse movements (cursor going straight out of the
screen), key pad only generating KEY_RIGHT and KEY_DOWN events.
A reproducer is:
int main(int argc, char ** argv)
{
char rel_x = 0x00; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x = 0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x |= ~0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
return 0;
}
(running on x86 or amd64)
$ ./test
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:-1 @test.c:8
(running on armv6)
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:255 @test.c:8
Forcing the rel_x and rel_y variables as signed char fixes the issue.
Reference: http://www.arm.linux.org.uk/docs/faqs/signedchar.php
Signed-off-by: Alexandre Lissy <alexandrelissy@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
We still need to fix up few places for multiplatform support,
but that can proceed separately. Fix the issue by making the
problem drivers depends !ARCH_MULTIPLATFORM for now.
The remaining pieces that are not multiplatform compatible
for omap2+ SoCs are:
1. Some drivers are using custom omap_dm_timer calls
There are two drivers that are directly usign omap hardware
timers for PWM and DSP clocking: drivers/media/rc/ir-rx51.c and
drivers/staging/tidspbridge/core/dsp-clock.c. These can be
fixed for multiplatform by allowing a minimal set of hardware
timers to be accessed, and for some functionality by using the
hrtimer framework.
2. Hardware OMAP4_ERRATA_I688 needs to be fixed up
This can't be enabled for multiplatform configurations in
it's current form. It may be possible to fix it up to do
instruction replacement early on during init. Luckily it
looks like this errata does not seem to get hit with
mainline kernel code alone at least currently.
3. Legacy header needed for omap-sham.c
Looks like it still needs mach/irqs.h for omap1 that
does not exist for multiplatform systems. Just ifdef
it for now.
4. Mailbox is waiting to get moved to drivers
Disable it for now to avoid adding a dependency to the
mailbox patches.
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Sean Young <sean@mess.org>
Cc: "Víctor Manuel Jáquez Leal" <vjaquez@igalia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
[tony@atomide.com: updated to disable mailbox]
Signed-off-by: Tony Lindgren <tony@atomide.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During modiles initialization rc-core schedules work which calls
request_module() several times to load ir-*-decoder modules, but
it does not wait or cancel this work on module unloading.
rc-core should use request_module_nowait() instead, because it
anyway cannot load modules synchronously or cancel/wait pending
work on unloading, because this leads to deadlock on modules_mutex
between several "modprobe" processes.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This error path is missing the unlock.
[mchehab@redhat.com: Merged two equal patches into one]
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ1QqgAAoJEHm+PkMAQRiG3GMIAJZjN2+0EGFpcq0LDrjIMyLG
PFuCkn9wNybAVR38DuVJkYclLclN2T1CevWZib+GgRLZO2IU5Qu1xh+fCLRn1u5i
qrxq8g4HYVMYXDixdZzXA2eXCLF7YLzPEdlowoBItGl9OJjQdzk3zBATtJGxfKaP
zvmaXP0CyoQekrZmmpMEl2/PLY/X0Ett6I5tlKcTvYKbbowG1SoAwVEVokCZC/vi
I+y8/8M68eDfOfYZ8BoRd5Lsygxfw8uvOce4qUeKawiZPO8bWP1s9NFyK6Ank6+s
hNXM9dNm6l0JfS+Ykb2FXleuEmOaaloRswOxukU1gKC3V0HdxwKx0Ir4P3z1dHM=
=5Iln
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc1' into staging/for_v3.9
Linux 3.8-rc1
* tag 'v3.8-rc1': (10696 commits)
Linux 3.8-rc1
Revert "nfsd: warn on odd reply state in nfsd_vfs_read"
ARM: dts: fix duplicated build target and alphabetical sort out for exynos
dm stripe: add WRITE SAME support
dm: remove map_info
dm snapshot: do not use map_context
dm thin: dont use map_context
dm raid1: dont use map_context
dm flakey: dont use map_context
dm raid1: rename read_record to bio_record
dm: move target request nr to dm_target_io
dm snapshot: use per_bio_data
dm verity: use per_bio_data
dm raid1: use per_bio_data
dm: introduce per_bio_data
dm kcopyd: add WRITE SAME support to dm_kcopyd_zero
dm linear: add WRITE SAME support
dm: add WRITE SAME support
dm: prepare to support WRITE SAME
dm ioctl: use kmalloc if possible
...
Conflicts:
MAINTAINERS
We recently introduced a new return -ENODEV in this function but we need
to unlock before returning.
[mchehab@redhat.com: found two patches with the same fix. Merged SOB's/acks into one patch]
Acked-by: Herton R. Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Douglas Bagnall <douglas@paradise.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This should fix a potential race condition, when the irq handler
triggers while rc_register_device is still setting up the rdev->raw
device.
This crash has not been observed in practice, but there should be a very
small window where it could occur. Since ir_raw_event_store_with_filter
checks if rdev->raw is not NULL before using it, this bug is not
triggered if the request_irq triggers a pending irq directly (since
rdev->raw will still be NULL then).
This commit was tested on nuvoton-cir only.
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a problem in fintek-cir and nuvoton-cir where the
irq handler would trigger during module load before the rdev member was
set, causing a NULL pointer crash.
It seems this crash is very reproducible (just bombard the receiver with
IR signals during module load), probably because when request_irq is
called, any pending intterupt is handled immediately, before
request_irq returns and rdev can be set.
This same crash was supposed to be fixed by commit
9ef449c6b3 ("[media] rc: Postpone ISR
registration"), but the crash was still observed on the nuvoton-cir
driver.
This commit was tested on nuvoton-cir only.
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before, labels were simply numbered. Now, the labels are named after the
cleanup action they'll perform (first), based on how the winbond-cir
driver does it. This makes the code a bit more clear and makes changes
in the ordering of labels easier to review.
This change is applied only to the rc drivers that do significant
cleanup in their probe functions: ati-remote, ene-ir, fintek-cir,
gpio-ir-recv, ite-cir, nuvoton-cir.
This commit should not change any code, it just renames goto labels.
[mchehab@redhat.com: removed changes at gpio-ir-recv.c, due to
merge conflicts]
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument there's no need to
subsequently call rc_free_device() on the same variable - in fact it's
a double free bug.
Easily fixed by just removing the rc_free_device() call.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At the 'err_request_irq' label, rc_unregister_device(rcdev) frees its
argument. So when we fall through to the 'err_gpio_request' label
further down and call rc_free_device(rcdev) then that's a double free.
Fix that by moving 'rcdev = NULL' from after the call to
rc_free_device() to after rc_unregister_device(). That fixes the
problem since rc_free_device() just does nothing if passed NULL and
there's no further use of 'rcdev' after the call to rc_free_device()
so it's not needed there.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- Missing MAINTAINERS entries were added for several drivers
- Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
sharing between V4L2 devices and GPU
- Got rid of all warnings when compiling with W=1 on x86
- Add a new driver for Exynos hardware (s3c-camif)
- Several bug fixes, cleanups and driver improvements
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] omap3isp: Prepare/unprepare clocks before/after enable/disable
[media] omap3isp: preview: Add support for 8-bit formats at the sink pad
[media] omap3isp: Replace printk with dev_*
[media] omap3isp: Find source pad from external entity
[media] omap3isp: Configure CSI-2 phy based on platform data
[media] omap3isp: Add PHY routing configuration
[media] omap3isp: Add CSI configuration registers from control block to ISP resources
[media] omap3isp: Remove unneeded module memory address definitions
[media] omap3isp: Use monotonic timestamps for statistics buffers
[media] uvcvideo: Fix control value clamping for unsigned integer controls
[media] uvcvideo: Mark first output terminal as default video node
[media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
[media] uvcvideo: Return -ENOTTY for unsupported ioctls
[media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
[media] uvcvideo: Don't fail when an unsupported format is requested
[media] uvcvideo: Return -EACCES when trying to access a read/write-only control
[media] uvcvideo: Set error_idx properly for extended controls API failures
[media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
[media] fc2580: write some registers conditionally
...
The winbond hardware has a counter for leading edges, which increases as
they are received. As we read raw IR from a fifo in an interrupt handler,
we cannot correlate them to specific IR pulses so we simply count all
pulses and edges until we go idle and disable the receiver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The receiver is never disabled by idle mode since rxstate never gets set
to RXSTATE_ACTIVE, so we keep on getting interrupts after the first IR
activity ends. Note that ir_raw_event_reset() already calls
ir_raw_event_handle().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"54fd321 [media] winbond: remove space from driver name" inadvertently
renamed the input device name.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the cleanup on probe failure more consistent with other
drivers. This is similar to what commit
f27b853ea2 ("[media] rc: Fix invalid
free_region and/or free_irq on probe failure") did for some other
drivers.
In addition to making the cleanup more consistent, this also fixes a
case where (on a ene_hw_detect failure) free_region would be called on a
region that was not requested yet.
This last problem was probably introduced by the moving of code in
commit b31b021988 ("[media] ene_ir: Fix
driver initialisation") and commit
9ef449c6b3 ("[media] rc: Postpone ISR
registration").
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Linux Media Mailing List <linux-media@vger.kernel.org>
drivers/media/rc/fintek-cir.c:687:5: warning: no previous prototype for 'fintek_init' [-Wmissing-prototypes]
drivers/media/rc/fintek-cir.c:692:6: warning: no previous prototype for 'fintek_exit' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The carrier detect return value is never used on nuvoton driver:
drivers/media/rc/nuvoton-cir.c: In function 'nvt_process_rx_ir_data':
drivers/media/rc/nuvoton-cir.c:623:6: warning: variable 'carrier' set but not used [-Wunused-but-set-variable]
Also, this would be called only if a boolean variable is enabled,
but there's no condition that enables it inside the driver. So,
comment the carrier detection code, as it might be useful later,
and remove the unused glue code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RC_TYPE_* defines are currently used both where a single protocol is
expected and where a bitmap of protocols is expected.
Functions like rc_keydown() and functions which add/remove entries to the
keytable want a single protocol. Future userspace APIs would also
benefit from numeric protocols (rather than bitmap ones). Keytables are
smaller if they can use a small(ish) integer rather than a bitmap.
Other functions or struct members (e.g. allowed_protos,
enabled_protocols, etc) accept multiple protocols and need a bitmap.
Using different types reduces the risk of programmer error. Using a
protocol enum whereever possible also makes for a more future-proof
user-space API as we don't need to worry about a sufficient number of
bits being available (e.g. in structs used for ioctl() calls).
The use of both a number and a corresponding bit is dalso one in e.g.
the input subsystem as well (see all the references to set/clear bit when
changing keytables for example).
This patch separate the different usages in preparation for
upcoming patches.
Where a single protocol is expected, enum rc_type is used; where one or more
protocol(s) are expected, something like u64 is used.
The patch has been rewritten so that the format of the sysfs "protocols"
file is no longer altered (at the loss of some detail). The file itself
should probably be deprecated in the future though.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We must move this for ARM common zImage support.
Note that neither drivers/media/rc/ir-rx51.c or
drivers/media/platform/omap3isp/ispvideo.c need
to include omap-pm.h, so this patch removes the
include for those files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ir-rc from my MSI DigiVox mini II Version 3 (af9015) will not work since
kernel 3.2.x.
sudo ir-keytable -t shows:
1348890734.303273: event MSC: scancode = 317
1348890734.303280: event key down: KEY_POWER (0x0074)
1348890734.303282: event sync
1348890734.553961: event key up: KEY_POWER (0x0074)
1348890734.553963: event sync
1348890741.303451: event MSC: scancode = 30d
1348890741.303457: event key down: KEY_DOWN (0x006c)
1348890741.303459: event sync
1348890741.553956: event key up: KEY_DOWN (0x006c)
So I changed in rc-msi-digivox-ii.c { 0x0002, KEY_2 }, to { 0x0302, KEY_2 },
and so on. And now it works well.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-snip-
ACTION=add
DEVPATH=/devices/pnp0/00:04/rc/rc0
DRV_NAME=Winbond CIR
NAME=rc-rc6-mce
SUBSYSTEM=rc
UDEV_LOG=6
USEC_INITIALIZED=88135858
run: '/usr/bin/ir-keytable -a /etc/rc_maps.cfg -s rc0'
Having a space makes it impossible to match in /etc/rc_maps.cfg.
[root@pequod ~]# udevadm test /sys/class/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the firmware already disables the receiver before transmit,
there is no need to do this from the driver.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These should be -ENOSYS because not -EINVAL.
Reported-by: Sean Young <sean@mess.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"carrier" comes from a get_user() in ir_lirc_ioctl(). We need to test
that it's not zero before using it as a divisor. It might have been
nice to test for this ir_lirc_ioctl() but the mceusb driver uses zero to
disable carrier modulation.
The bug in redrat3 is a little more subtle. The ->carrier is passed to
mod_freq_to_val() which uses it as a divisor.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change winbond-cir's tx support to be asynchronous and not to mess with
the TX buffer. Essentially the winbond-cir counterpart to the patch
Sean Young sent for iguanair.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a minor correctness fix for the duration calculation in
winbond-cir (the read value should be incremented by one).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DIV_ROUND_CLOSEST is faster if the compiler knows it will only be
dealing with unsigned dividends.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Although this kind of IR diode circuitry is known to exist only in
N900 hardware, nothing prevents making similar circuitry on any OMAP
based board. The MACH_NOKIA_RX51 dependency is thus not something we
want to be there.
Also, this should depend on LIRC as it is a LIRC driver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Fix typo
-Change pwm_timer_num type to match type in platform data
-Remove extra parenthesis
-Replace magic constant with proper bit defintions
-Remove duplicate exit pointer
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While here, fix the led name: the led is green, not yellow.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit "[media] rc-core: move timeout and checks to lirc", the
incoming buffer is used after the driver transmits.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"[media] rc-core: move timeout and checks to lirc" introduced a buffer
overrun by passing the number of bytes, rather than the number of samples,
to the transmit function.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ite_dev::rdev is currently initialised in ite_probe() after
rc_register_device() returns. If a newly registered device is opened
quickly enough, we may enable interrupts and try to use ite_dev::rdev
before it has been initialised. Move it up to the earliest point we
can, right after calling rc_allocate_device().
Reported-and-tested-by: YunQiang Su <wzssyqa@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQNUEyAAoJEHm+PkMAQRiGs+sH/iLtdAVcfBfUwdmGV0qDXbVE
L3gCg3IERPCSaQo8qsT3zujdLAQ2HsiMs73jbqJaBWSV16ZMqkglRKbn+QMGpqJV
bi/pf5Akrm9IL/u+427ycB8QxzyjGal8uJ6btuwXa03VROSfOsEiQbtsByFNaDv/
8oq0/DaE8mWRedlcAaeN+l8nD4Enb2jSKp0UADkBMnUr4KCbwSVQ+ITXAggqVq23
htA3Yt0oGf1JYq+k99D5k92h0I/4VwiorUgwPKhmS5DM9gVtJ4L+SigbekS/MFq+
huyzOHRWlO++OxBlgSTMuJAE1k/G2B7tGeoERY0tEL/hAWcKYTfGIXSc7X6JvM0=
=Dmsv
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc3' into staging/for_v3.7
Linux 3.6-rc3
* tag 'v3.6-rc3': (764 commits)
Linux 3.6-rc3
task_work: add a scheduling point in task_work_run()
fs: fix fs/namei.c kernel-doc warnings
eventpoll: use-after-possible-free in epoll_create1()
vfio: grab vfio_device reference *before* exposing the sucker via fd_install()
vfio: get rid of vfio_device_put()/vfio_group_get_device* races
vfio: get rid of open-coding kref_put_mutex
introduce kref_put_mutex()
vfio: don't dereference after kfree...
fbcon: fix race condition between console lock and cursor timer (v1.1)
mm: compaction: Abort async compaction if locks are contended or taking too long
mm: have order > 0 compaction start near a pageblock with free pages
rapidio/tsi721: fix unused variable compiler warning
rapidio/tsi721: fix inbound doorbell interrupt handling
drivers/rtc/rtc-rs5c348.c: fix hour decoding in 12-hour mode
mm: correct page->pfmemalloc to fix deactivate_slab regression
drivers/rtc/rtc-pcf2123.c: initialize dynamic sysfs attributes
mm/compaction.c: fix deferring compaction mistake
drivers/misc/sgi-xp/xpc_uv.c: SGI XPC fails to load when cpu 0 is out of IRQ resources
string: do not export memweight() to userspace
...
The lirc TX functionality expects the process which writes (TX) data to
the lirc dev to sleep until the actual data has been transmitted by the
hardware.
Since the same timeout calculation is duplicated in more than one driver
(and would have to be duplicated in even more drivers as they gain TX
support), it makes sense to move this timeout calculation to the lirc
layer instead.
At the same time, centralize some of the sanity checks.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the driver for the IR transmitter diode found on the Nokia
N900 (also known as RX51) device. The driver is mostly the same as
found in the original 2.6.28 based kernel that comes with the device.
The following modifications have been made compared to the original
driver version:
- Adopt to the changes that has happen in the kernel during the past
five years, such as the change in the include paths
- The OMAP DM-timers require much more care nowadays. The timers need
to be enabled and disabled or otherwise many actions fail. Timers
must not be freed without first stopping them or otherwise the timer
cannot be requested again.
The code has been tested with sending IR codes with N900 device
running Debian userland. The device receiving the codes was Anysee
DVB-C USB receiver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently write() will return 0 if an IR device does not support sending.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The TechnoTrend USB IR Receiver sends 125 ISO URBs per second, even when
there is no IR activity. Reduce the number of wake ups from the other
drivers too.
This saves about 0.25ms/s on a 2.4GHz Core 2 according to powertop.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver adds support for TechnoTrend USB IR Receiver. It is a complete
rewrite of the staging/media/lirc/lirc_ttusbir driver. It adds more
accurate sample reporting and led control.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Pioneer CU-700 remote causes receiver overflows if you hold down any
button. The remote does not send NEC IR repeats, it repeats the entire
NEC code after 20ms.
The iguanair hardware advertises an interval of 10 which just not enough;
with 100 URBs per second and at most 7 edges per URB, we handle at most
700 edges per second. The remote generates about 900.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the timeout supplied the interface can go idle. The keymap is
the same one as other drivers which do not come with a remote.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware versions lower than 0x0205 use a different interface which is not
supported. Also report the firmware version in the standard format.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than using usb_interrupt_msg() to receive responses, reuse the
urb callback we already have in place.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the error
drivers/usb/core/hub.c:3753: undefined reference to `usb_speed_string'
seen in various random configurations.
Cc: Sean Young <sean@mess.org>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This remote sends a header pulse of 8150us followed by a space of 4000us.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB identifiers for MCE compatible I/R transceivers from Twisted Melon.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
changes:
1. wrap some lines that are longer than 80 characters.
2. remove local function prototype declarations which do not
need.
3. replace TAB character with a space character in function
comments.
Signed-off-by: Du, Changbin <changbin.du@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason, when the lirc daemon learns that a usb remote control
has been unplugged, it wants to read the sysfs attributes of the
disappearing device. This is useful for uncovering transient
inconsistencies, but less so for keeping the system running when such
inconsistencies exist.
Under some circumstances (like every time I unplug my dvb stick from
my laptop), lirc catches an rc_dev whose raw event handler has been
removed (presumably by ir_raw_event_unregister), and proceeds to
interrogate the raw protocols supported by the NULL pointer.
This patch avoids the NULL dereference, and ignores the issue of how
this state of affairs came about in the first place.
Version 2 incorporates changes recommended by Mauro Carvalho Chehab
(-ENODEV instead of -EINVAL, and a signed-off-by).
Signed-off-by: Douglas Bagnall <douglas@paradise.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (31 commits)
[media] Revert "[media] V4L: JPEG class documentation corrections"
[media] s5p-fimc: Add missing FIMC-LITE file operations locking
[media] omap3isp: preview: Fix contrast and brightness handling
[media] omap3isp: preview: Fix output size computation depending on input format
[media] winbond-cir: Initialise timeout, driver_type and allowed_protos
[media] winbond-cir: Fix txandrx module info
[media] cx23885: Silence unknown command warnings
[media] cx23885: add support for HVR-1255 analog (cx23888 variant)
[media] cx23885: make analog support work for HVR_1250 (cx23885 variant)
[media] cx25840: fix vsrc/hsrc usage on cx23888 designs
[media] cx25840: fix regression in HVR-1800 analog audio
[media] cx25840: fix regression in analog support hue/saturation controls
[media] cx25840: fix regression in HVR-1800 analog support
[media] s5p-mfc: Fixed setup of custom controls in decoder and encoder
[media] cx231xx: don't DMA to random addresses
[media] em28xx: fix em28xx-rc load
[media] dvb-core: Release semaphore on error path dvb_register_device()
[media] s5p-fimc: Stop media entity pipeline if fimc_pipeline_validate fails
[media] s5p-fimc: Fix compiler warning in fimc-lite.c
[media] s5p-fimc: media_entity_pipeline_start() may fail
...
No need to duplicate normal kernel logging capabilities.
Add pr_fmt and convert pr_reg to pr_info.
Remove pr_reg macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to set a timeout so we can go idle on no activity.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We aren't getting any module info for the txandx option because
of a typo:
parm: txandrx:bool
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's better to give platform code a chance to specify the allowed
protocols to use.
[mchehab@redhat.com: fix merge conflict with a patch that made
half of this change]
Signed-off-by: Du, Changbin <changbin.du@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Better arrange the remote controller driver items to happen after the
core support, on their proper menus, and making clerarer what is media
core options and what is media driver options.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the main items to:
<m> Multimedia support --->
[ ] Cameras/video grabbers support
[ ] Analog TV support
[ ] Digital TV support
[ ] AM/FM radio receivers/transmitters support
[ ] Remote Controller support
This provides an interface that is clearer to end users that
are compiling the Kernel, and will allow the building system
to automatically unselect drivers for unused functions.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 9ef449c6b3 ("[media] rc: Postpone ISR
registration") fixed an early ISR registration on several drivers. It did
however also introduced a bug by moving the invocation of pnp_port_start()
to the end of the probe function.
This patch fixes this issue by moving the invocation of pnp_port_start() to
an earlier stage in the probe function.
Cc: stable@vger.kernel.org
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it possible for gpio-ir-recv users to choose a map name.
Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing information so that udev can create an entry for gpio-ir-recv under
/dev/input/by-path/ .
Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch just removes the second assignment "rc->priv = &loopdev;"
that happens a fews lines after the first one.
Signed-off-by: Michel Machado <michel@digirati.com.br>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
CC: "David Härdeman" <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fintek-cir, ite-cir and nuvoton-cir may try to free an I/O region
and/or IRQ handler that was never allocated after a failure in their
respective probe functions. Add and use separate labels on the
failure path so they will do the right cleanup after each possible
point of failure.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are many different Medion X10 remotes that need slightly different
keymaps. We may not yet have all the needed keymaps, in which case a
wrong keymap may be used. This happened with Medion X10 OR2x remotes
before the keymap for them was added, causing the ati_remote driver to
select the Medion Digitainer keymap instead. Unfortunately, the Medion
Digitainer keymap doesn't have the standard X10 up/down scancodes
assigned to KEY_UP and KEY_DOWN keycodes, making wrongly assigned
remotes mostly unusable.
Add the regular KEY_UP and KEY_DOWN scancodes to the Medion X10
Digitainer keymap, making any Medion remote mostly usable even when
wrongly used with that keymap (standard buttons, such as
up/down/left/right, 0-9, play/stop/pause, have the same scancode in all
the X10 remotes).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add another Medion X10 remote keymap. This is for the Medion OR2x
remotes with the Windows MCE button.
The receiver shipped with this remote has the same USB ID as the other
Medion receivers, but the name is different and is therefore used to
detect this variant.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus/master: (805 commits)
tty: Fix LED error return
openvswitch: checking wrong variable in queue_userspace_packet()
bonding: Fix LACPDU rx_dropped commit.
Linux 3.4-rc7
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
MAINTAINERS: Add myself as the cpufreq maintainer
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
ks8851: Update link status during link change interrupt
...
Conflicts:
drivers/media/common/tuners/xc5000.c
drivers/media/common/tuners/xc5000.h
drivers/usb/gadget/uvc_queue.c
Drivers that refer to a __devexit function in an operations
structure need to annotate that pointer with __devexit_p so
replace it with a NULL pointer when the section gets discarded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IR sony decoder is making use of 'bitrev8' that,
in turn, requires BITREVERSE.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
media_build/v4l/drxk_hard.c: In function 'DownloadMicrocode':
media_build/v4l/drxk_hard.c:1388:6: warning: variable 'BlockCRC' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1384:6: warning: variable 'Drain' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1383:6: warning: variable 'Flags' set but not used [-Wunused-but-set-variable]
media_build/v4l/lmedm04.c: In function 'lme2510_probe':
media_build/v4l/lmedm04.c:1208:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hopper_cards.c: In function 'hopper_irq_handler':
media_build/v4l/hopper_cards.c:68:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_cards.c: In function 'mantis_irq_handler':
media_build/v4l/mantis_cards.c:76:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c: In function 'mantis_dma_stop':
media_build/v4l/mantis_dma.c:202:16: warning: variable 'mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c:202:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_evm.c: In function 'mantis_hifevm_work':
media_build/v4l/mantis_evm.c:44:17: warning: variable 'gpif_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_init_calc':
media_build/v4l/stb0899_drv.c:640:5: warning: variable 'agc1cn' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_diseqc_init':
media_build/v4l/stb0899_drv.c:830:13: warning: variable 'f22_rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c:826:31: warning: variable 'tx_data' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0900_sw.c: In function 'stv0900_track_optimization':
media_build/v4l/stv0900_sw.c:838:26: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/ir-sanyo-decoder.c: In function 'ir_sanyo_decode':
media_build/v4l/ir-sanyo-decoder.c:59:14: warning: variable 'not_address' set but not used [-Wunused-but-set-variable]
media_build/v4l/mceusb.c: In function 'mceusb_dev_printdata':
media_build/v4l/mceusb.c:523:46: warning: variable 'data5' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current condition is always true, so everything uses
LOGICAL_DEV_CIR_REV2 (8). It should be that Fintek products
0x0408(F71809) and 0x0804(F71855) use logical device
LOGICAL_DEV_CIR_REV1 (5) and other chip ids use logical device 8.
In other words, this fixes hardware detection for 0x0408 and 0x0804.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An early registration of an ISR was causing a crash to several users (for
example, with the ite-cir driver: http://bugs.launchpad.net/bugs/972723).
The reason was that IRQs were being triggered before a driver
initialisation was completed.
This patch fixes this by moving the invocation to request_irq() and to
request_region() to a later stage on the driver probe function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setting the correct mode is required by rc-core or scancodes won't be
generated (which isn't very user-friendly).
This one-line fix should be suitable for 3.4-rc2.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for another Medion X10 remote. This was apparently
originally used with the Medion Digitainer box, but is now sold
separately without any Digitainer labeling.
A peculiarity of this remote is a scrollwheel in place of up/down
buttons. Each direction is mapped to 8 different scancodes, each
corresponding to 1..8 notches, allowing multiple notches to the same
direction to be transmitted in a single scancode. The driver transforms
the multi-notch scancodes to multiple events of the single-notch
scancode.
(0x70..0x77 = 1..8 notches down, 0x78..0x7f = 1..8 notches up)
Since the scrollwheel scancodes are the same that are used for mouse on
some other X10 (ati_remote) remotes, the driver will now check whether
the active keymap has a keycode defined for the single-notch scancode
when a mouse/scrollwheel scancode (0x70..0x7f) is received. If set,
scrollwheel is assumed, otherwise mouse is assumed.
This remote ships with a different receiver than the already supported
Medion X10 remote, but they share the same USB ID. The only difference
in the USB descriptors is that the Digitainer receiver has the Remote
Wakeup bit set in bmAttributes of the Configuration Descriptor.
Therefore that is used to select the default keymap.
Thanks to Stephan Raue from OpenELEC (www.openelec.tv) for providing me
both a Medion X10 Digitainer remote+receiver and an already supported
Medion X10 remote+receiver. Thanks to Martin Beyss for providing some
useful information about the remote (including the "Digitainer" name).
This patch has been tested by both of them and myself.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Stephan Raue <stephan@openelec.tv>
Tested-by: Martin Beyss <Martin.Beyss@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the ati_remote default keymap is selected directly based on
the USB device id.
Add support for instead specifying a function returning the default
keymap, allowing more complex selection logic to be added when needed.
This will be used for Medion X10 remotes in a following commit.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes BUG_ON in ir_raw_event_thread which IMO is a
over-kill, and this kills the ir_raw_event_thread too. With a bit of
additional logic in this patch, we nomore need to kill this thread.
Other disadvantage of having a BUG-ON is,
wake_up_process(dev->raw->thread) called on dead thread via
ir_raw_event_handle will result in total lockup in SMP system.
Advantage of this patch is ir-raw event thread is left in a usable state
even if the fifo does not have enough bytes.
This patch sets the thread into TASK_INTERRUPTIBLE if raw-fifo has less
then sizeof(struct ir_raw_event) bytes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes rc_core to not load the IR decoders at load time,
postponing it to load only if a RC_DRIVER_IR_RAW device is
registered via rc_register_device.
We use a static boolean variable, to ensure decoders modules
are only loaded once.
Tested with rc-loopback device only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Yet another device ID that has started showing up in the wild.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are couple places where we check unsigned values for negative. I
changed ->gpin_nr to signed because in gpio_ir_recv_probe() we do:
if (pdata->gpio_nr < 0)
return -EINVAL;
I also change gval to a signed int in gpio_ir_recv_irq() because that's
the type that gpio_get_value_cansleep() returns and we test for negative
returns.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3': (1646 commits)
Linux 3.3
Don't limit non-nested epoll paths
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
nilfs2: clamp ns_r_segments_percentage to [1, 99]
afs: Remote abort can cause BUG in rxrpc code
afs: Read of file returns EBADMSG
C6X: remove dead code from entry.S
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
MAINTAINERS: Add Serge as maintainer of capabilities
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
...
The raw Sony IR decoder decodes 15bit messages slightly incorrectly.
To decode the function number, it shifts the bits right by 7 so that the
function is in bits 7:1, masks with 0xFD (0b11111101), and does an 8 bit
reverse so it ends up in bits 6:0. The mask should be 0xFE to correspond
with bits 7:1 (0b11111110).
The old mask had the effect of dropping the MSB of the function number
from bit 6, and leaving the LSB of the device number in bit 7.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds GPIO based IR Receiver driver. It decodes signals using decoders
available in rc framework.
Signed-off-by: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Raw IR events are passed to the raw event thread through a kfifo. The
size of the event struct is 12 bytes, and space for 512 events is
reserved in the kfifo (6144 bytes), however this is rounded down to 4096
bytes (the next power of 2) by __kfifo_alloc().
4096 bytes is not divisible by 12 therefore if the fifo fills up a third
of a record will be written in the end of the kfifo by
ir_raw_event_store() because the recsize of the fifo is 0 (it doesn't
have records). When this is read by ir_raw_event_thread() a corrupted or
partial record will be read, and in the case of a partial record the
BUG_ON(retval != sizeof(ev)) gets hit too.
According to samples/kfifo/record-example.c struct kfifo_rec_ptr_1 can
handle records of a length between 0 and 255 bytes, so change struct
ir_raw_event_ctrl to use that instead of struct kfifo.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] hdpvr: update picture controls to support firmware versions > 0.15
[media] wl128x: fix build errors when GPIOLIB is not enabled
[media] hdpvr: fix race conditon during start of streaming
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
[media] imon: don't wedge hardware after early callbacks
This patch is just a minor update to one titled "imon: Input from ffdc
device type ignored" from Corinna Vinschen. An earlier patch to prevent
an oops when we got early callbacks also has the nasty side-effect of
wedging imon hardware, as we don't acknowledge the urb. Rework the check
slightly here to bypass processing the packet, as the driver isn't yet
fully initialized, but still acknowlege the urb and submit a new rx_urb.
Do this for both interfaces -- irrelevant for ffdc hardware, but
relevant for newer hardware, though newer hardware doesn't spew the
constant stream of data as soon as the hardware is initialized like the
older ffdc devices, so they'd be less likely to trigger this anyway...
Tested with both an ffdc device and an 0042 device.
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3-rc1': (8187 commits)
Linux 3.3-rc1
x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
qnx4: don't leak ->BitMap on late failure exits
qnx4: reduce the insane nesting in qnx4_checkroot()
qnx4: di_fname is an array, for crying out loud...
KEYS: Permit key_serial() to be called with a const key pointer
keys: fix user_defined key sparse messages
ima: fix cred sparse warning
uml: fix compile for x86-64
MPILIB: Add a missing ENOMEM check
tpm: fix (ACPI S3) suspend regression
nvme: fix merge error due to change of 'make_request_fn' fn type
xen: using EXPORT_SYMBOL requires including export.h
gpio: tps65910: Use correct offset for gpio initialization
acpi/apei/einj: Add extensions to EINJ from rev 5.0 of acpi spec
intel_idle: Split up and provide per CPU initialization func
ACPI processor: Remove unneeded variable passed by acpi_processor_hotadd_init V2
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
...
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (655 commits)
[media] revert patch: HDIC HD29L2 DMB-TH USB2.0 reference design driver
mb86a20s: Add a few more register settings at the init seq
mb86a20s: Group registers into the same line
[media] [PATCH] don't reset the delivery system on DTV_CLEAR
[media] [BUG] it913x-fe fix typo error making SNR levels unstable
[media] cx23885: Query the CX25840 during enum_input for status
[media] cx25840: Add support for g_input_status
[media] rc-videomate-m1f.c Rename to match remote controler name
[media] drivers: media: au0828: Fix dependency for VIDEO_AU0828
[media] convert drivers/media/* to use module_platform_driver()
[media] drivers: video: cx231xx: Fix dependency for VIDEO_CX231XX_DVB
[media] Exynos4 JPEG codec v4l2 driver
[media] doc: v4l: selection: choose pixels as units for selection rectangles
[media] v4l: s5p-tv: mixer: fix setup of VP scaling
[media] v4l: s5p-tv: mixer: add support for selection API
[media] v4l: emulate old crop API using extended crop/compose API
[media] doc: v4l: add documentation for selection API
[media] doc: v4l: add binary images for selection API
[media] v4l: add support for selection api
[media] hd29l2: fix review findings
...
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This remote was added with support for card Compro VideoMate M1F.
This remote is shipped with various Compro cards, not this one only.
Furthermore this remote can be bought separately under name Compro
VideoMate K100.
http://compro.com.tw/en/product/k100/k100.html
So give it a proper name.
[mchehab@redhat.com: Fix the Makefile]
Signed-off-by: Samuel Rakitničan <samuel.rakitnican@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
both callers of device_get_devnode() are only interested in lower 16bits
and nobody tries to return anything wider than 16bit anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linux 3.2-rc7
* tag 'v3.2-rc7': (1304 commits)
Linux 3.2-rc7
netfilter: xt_connbytes: handle negation correctly
Btrfs: call d_instantiate after all ops are setup
Btrfs: fix worker lock misuse in find_worker
net: relax rcvbuf limits
rps: fix insufficient bounds checking in store_rps_dev_flow_table_cnt()
net: introduce DST_NOPEER dst flag
mqprio: Avoid panic if no options are provided
bridge: provide a mtu() method for fake_dst_ops
md/bitmap: It is OK to clear bits during recovery.
md: don't give up looking for spares on first failure-to-add
md/raid5: ensure correct assessment of drives during degraded reshape.
md/linear: fix hot-add of devices to linear arrays.
sparc64: Fix MSIQ HV call ordering in pci_sun4v_msiq_build_irq().
pata_of_platform: Add missing CONFIG_OF_IRQ dependency.
ipv4: using prefetch requires including prefetch.h
VFS: Fix race between CPU hotplug and lglocks
vfs: __read_cache_page should use gfp argument rather than GFP_KERNEL
USB: Fix usb/isp1760 build on sparc
net: Add a flow_cache_flush_deferred function
...
Conflicts:
drivers/media/common/tuners/tda18218.c
drivers/media/video/omap3isp/ispccdc.c
drivers/staging/media/as102/as102_drv.h
The ati_remote driver currently uses 2-byte scancodes. However, one of
those bytes is actually a checksum and therefore shouldn't be considered
as part of the scancode.
Fix the driver to only use the actual data byte as a scancode and to
check the checksum itself. Update the bundled keymaps accordingly.
Since ati_remote was only migrated to the rc subsystem for 3.2, the
previous scancodes weren't emitted on any stable kernel.
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed submit urb logic so hardware doesn't hang trying to transmit
signal data
Removed unneeded enable/disable detector commands in
redrat3_transmit_ir (the hardware does this anyway) and converted
arguments to unsigned as per 5588dc2
Signed-off-by: Andrew Vincer <andrew@redrat.co.uk>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I get this error when compiling for_v3.3:
There is a include <linux/module.h> missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch to the IR RC6 decoder adds support for variable length
mode-6A frames which can range in size from 8 to 128 bits. Please refer
to the following link for a detailed explanation or RC6 frames:
http://slydiman.narod.ru/scr/kb/rc6.htm
This change removes the assumption that frames are fixed length
(currently either 24 or 32 data bits) and actually counts the number of
bits until an end of frame marker is seen.
[mchehab@redhat.com: Tested with a RC-6(0) IR - 16 bits]
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.2-rc2': (3068 commits)
Linux 3.2-rc2
hfs: add sanity check for file name length
fsl-rio: fix compile error
blackfin: Fixup export.h includes
Blackfin: add serial TX IRQ in individual platform resource
virtio-pci: fix use after free
ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
drm/radeon/kms/combios: fix dynamic allocation of PM clock modes
[CPUFREQ] db8500: fix build error due to undeclared i variable
bma023: Add SFI translation for this device
vrtc: change its year offset from 1960 to 1972
ce4100: fix a build error
arm/imx: fix imx6q mmc error when mounting rootfs
arm/imx: fix AUTO_ZRELADDR selection
arm/imx: fix the references to ARCH_MX3
ARM: mx51/53: set pwm clock parent to ipg_perclk
btrfs: rename the option to nospace_cache
drm/radeon/kms/pm: switch to dynamically allocating clock mode array
drm/radeon/kms: optimize r600_pm_profile_init
drm/radeon/kms/pm: add a proper pm profile init function for fusion
...
Conflicts:
drivers/media/radio/Kconfig
This converts the drivers in drivers/media/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Frank Zago <frank@zago.net>
Cc: Olivier Lorin <o.lorin@laposte.net>
Cc: Erik Andren <erik.andren@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Brian Johnson <brijohn@gmail.com>
Cc: Leandro Costantino <lcostantino@gmail.com>
Cc: Antoine Jacquet <royale@zerezo.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Florian Mickler <florian@mickler.org>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Michael Krufky <mkrufky@kernellabs.com>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Florent Audebert <florent.audebert@anevia.com>
Cc: Sam Doshi <sam@metal-fish.co.uk>
Cc: Manu Abraham <manu@linuxtv.org>
Cc: Olivier Grenie <olivier.grenie@dibcom.fr>
Cc: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Cc: "Igor M. Liplianin" <liplianin@me.by>
Cc: Derek Kelly <user.vdr@gmail.com>
Cc: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: "André Weidemann" <Andre.Weidemann@web.de>
Cc: Martin Wilks <m.wilks@technisat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jose Alberto Reguero <jareguero@telefonica.net>
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Rafi Rubin <rafi@seas.upenn.edu>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Paul Bender <pebender@gmail.com>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: "Márcio A Alves" <froooozen@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Chris Rankin <rankincj@yahoo.com>
Cc: Lee Jones <lee.jones@canonical.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Dean Anderson <linux-dev@sensoray.com>
Cc: Pete Eberlein <pete@sensoray.com>
Cc: Arvydas Sidorenko <asido4@gmail.com>
Cc: Andrea Anacleto <andreaanacleto@libero.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in clocksource
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These two macros were in module.h but now module.h is no longer
sprayed across every source file imaginable, so the users need
to expicitly call out their use of them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To fix:
drivers/media/rc/ir-raw.c: In function 'init_decoders':
drivers/media/rc/ir-raw.c:354:2: error: implicit declaration of function 'request_module'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The code here treated user pointers correctly, but the __user tags
weren't used correctly so it caused Sparse warnings:
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts some ifdef'd wrapper functions from macros to static inline
functions to kill the following warnings issued by GCC:
CC [M] drivers/media/rc/ir-raw.o
drivers/media/rc/ir-raw.c: In function ‘init_decoders’:
drivers/media/rc/ir-raw.c:353:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:354:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:355:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:356:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:357:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:359:2: warning: statement with no effect [-Wunused-value]
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The protocol differs by having two toggle bits in the scancode. Since
one of the bits is otherwise unused, we can safely handle the bits
unconditionally.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ati_remote_dump() function tries to not print "Weird byte" warning
for 1-byte responses that contain 0xff or 0x00, but it doesn't work
properly as it simply falls back to the "Weird data" warning in the else
clause.
Fix that by adding an inner if clause.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The keycode mangling algorithm is kept the same, so the new external
keymap has the same values as the old static table.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver will be migrated to the RC driver API in a following
commit.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon devices have either 1 or 2 usb interfaces on them, each wired
up to its own urb callback. The interface 0 urb callback is wired up
before the imon context's rc_dev pointer is filled in, which is
necessary for imon 0xffdc device auto-detection to work properly, but we
need to make sure we don't actually run the callback routines until
we've entirely filled in the necessary bits for each given interface,
lest we wind up oopsing. Technically, any imon device could have hit
this, but the issue is exacerbated on the 0xffdc devices, which send a
constant stream of interrupts, even when they have no valid key data.
CC: Andy Walls <awalls@md.metrocast.net>
CC: Chris W <lkml@psychogeeks.com>
Reported-by: Chris W <lkml@psychogeeks.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.1-rc6': (1902 commits)
Linux 3.1-rc6
ioctl: register LTTng ioctl
fuse: fix memory leak
fuse: fix flock breakage
Btrfs: add dummy extent if dst offset excceeds file end in
Btrfs: calc file extent num_bytes correctly in file clone
btrfs: xattr: fix attribute removal
Btrfs: fix wrong nbytes information of the inode
Btrfs: fix the file extent gap when doing direct IO
Btrfs: fix unclosed transaction handle in btrfs_cont_expand
Btrfs: fix misuse of trans block rsv
Btrfs: reset to appropriate block rsv after orphan operations
Btrfs: skip locking if searching the commit root in csum lookup
btrfs: fix warning in iput for bad-inode
Btrfs: fix an oops when deleting snapshots
[media] vp7045: fix buffer setup
[media] nuvoton-cir: simplify raw IR sample handling
[media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL
[media] v4l2: Fix documentation of the codec device controls
[media] gspca - sonixj: Fix the darkness of sensor om6802 in 320x240
...
The nuvoton-cir driver was storing up consecutive pulse-pulse and
space-space samples internally, for no good reason, since
ir_raw_event_store_with_filter() already merges back to back like
samples types for us. This should also fix a regression introduced late
in 3.0 that related to a timeout change, which actually becomes correct
when coupled with this change. Tested with RC6 and RC5 on my own
nuvoton-cir hardware atop vanilla 3.0.0, after verifying quirky
behavior in 3.0 due to the timeout change.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add pr_fmt.
Convert ene_warn and ene_notice to pr_<level>.
Use pr_debug in __dbg macro and a little neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
The following patch adds the IR code for the missing "OK" key to the Pinnacle
PCTV HD map. This map is now used by the PCTV 290e DVB-T2 device, whose remote
control has 26 buttons.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add note about recent updates coming from Microsoft's publicly available
specs on Windows Media Center remotes and receivers/transmitters.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than dumping out hex values, lets print the actual calculated
frequency and period the hardware has been configured for. After this
[ 2643.276215] mceusb 3-1:1.0: tx data: 9f 07 (length=2)
[ 2643.276218] mceusb 3-1:1.0: Get carrier mode and freq
[ 2643.277206] mceusb 3-1:1.0: rx data: 9f 06 01 42 (length=4)
[ 2643.277209] mceusb 3-1:1.0: Got carrier of 37037 Hz (period 27us)
Matches up perfectly with the table in Microsoft's docs.
Of course, I've noticed on one of my devices that the MS-recommended
default value of 1 for carrier pre-scaler and 66 for carrier period was
butchered, and instead of converting 66 to hex (0x42 like above), they
put in 0x66, so the hardware reports a default carrier of 24390Hz.
Fortunately, I guess, this particular device is rx-only, but I wouldn't
put it past other hw to screw up here too.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the specs, you can read the number of tx ports, number of
rx sensors, which tx ports have cables plugged into them, and which rx
sensors are active. In practice, most of my devices do seem to report
sane values for tx ports and rx sensors (but not all -- one without any
tx ports reports having them), and most report the active sensor
correctly, but only one of eight reports cabled tx ports correctly. So
for the most part, this is just for informational purposes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Supposedly, there are essentially three different classes of devices
that are compatible with Microsoft's specs. First are the "legacy"
devices, which are built using Microsoft-provided hardware specs and
firmware. Second are "emulator" devices, which are built using custom
hardware and firmware, written to emulate Microsoft's firmware. Third
are "port" devices, which have their own device driver and firmware,
which provides compatible data to higher levels of the stack.
>From what I can tell, things like nuvoton-cir and fintek-cir are
essentially "port" devices -- their raw IR buffer format is very similar
to that of the mceusb devices. Now, within the mceusb driver, we have
three different "generations", which at first, seemed like maybe they
mapped to emulator versions. Unfortuantely, every single device I have
responds "illegal command" to the query to get firmware emulator version
from the hardware, which means they're either all emulator version 1, or
they're legacy devices, and our different "generations" aren't at all
related here. Though in theory, its possible the gen1 devices are
"legacy" devices and the rest are emulator v1. There are some useful
features of the v2 interface I was hoping to play with, but alas...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to MS docs, the device firmware may halt after receiving an
unknown instruction, but that it should be possible to tell the firmware
to continue running by simply sending a device resume command. So lets
do that.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Its not uncommon for folks to force these bits enabled, because people
do want to wake their htpc kit via their remote. Lets just set the bits
for 'em.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes the init routine is blasting commands out to the hardware
faster than it can reply. Throw a brief delay in there to give the
hardware a chance to reply before we send the next command.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I was recently pointed to the document titled
Windows-Media-Center-RC-IR-Collection-Green-Button-Specification-03-08-2011-V2.pdf
which as of this writing, is publicly available from
download.microsoft.com. It covers a LOT of the gaps in the mceusb
driver, which to this point, was written almost entirely by
reverse-engineering. First up, I'm updating the defines for all the MCE
commands and responses to match their names in the spec. More to come...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are folks with flaky imon hardware out there that doesn't always
respond to requests to write to their displays for some reason, which
can flood logs quickly when something like lcdproc is trying to
constantly update the display, so lets rate-limit all that error spew.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc unregister logic were deadly broken, preventing some drivers to
be removed. Among the broken things, rc_dev_uevent() is being called
during device_del(), causing a data filling on an area that it is
not ready anymore.
Also, some drivers have a stop callback defined, that needs to be called
before data removal, as it stops data polling.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: warning: function declaration isn't a prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is admittedly a bit of a hack, but if we change our timeout value
to something longer and fudge our synthesized trailing space sample
based on the initial pulse sample, rc-core decode continues to work just
fine with both rc-6 and rc-5, and now lirc userspace decode shows proper
repeats for both of those protocols as well. Also tested NEC
successfully with both decode options.
We do still need a reset timer callback using the hardware's timeout
value to make sure we actually process samples correctly, regardless of
our somewhat hacky timeout and synthesized trailer above.
This also adds a missing del_timer_sync call to the module unload path.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trying to cap duration before multiplying it was obviously wrong.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already add a trailing space, this wasn't doing anything useful, and
actually confused lirc userspace a bit. Rip it out.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Microsoft's Windows Media Center specification and requirements doc from
2011.03.18 now refers to the former Power Toggle button as the Sleep
Toggle, and recommends using a new moon sleep icon for it. Its the same
key, but its apparently always been meant to put the system to sleep,
not power it off. Adjust accordingly. While we're here, lets also remove
the duplicate KEY_PLAYPAUSE entry.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Durations can never be negative, so it makes sense to consistently use
unsigned int for LIRC transmission. Contrary to the initial impression,
this shouldn't actually change the userspace API.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The conversion of winbond-cir to use rc-core seems to have missed a
a few bits and pieces which were in my local tree. Kudos to
Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing.
[mchehab@redhat.com: fix two UTF-8 violations]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the original code, if the allocation failed we dereference "rr3"
when it was NULL.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If change_protocol() fails and we goto out_raw, then it calls unlock
twice. I noticed that the other time we called change_protocol() we
held the &dev->lock, so I changed it to hold it here too.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
The nuvoton-cir inherited an insanely low idle timeout value from the
mceusb driver. We're fixing mceusb, should fix this driver too.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This matches the typical timeout advertised by hardware, once we're
actually interpreting it correctly.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unit missmatch in mceusb_handle_command. It should be converting to us,
not 1/10th of ms.
mceusb_dev_printdata 100us/ms -> 1000us/ms
Alter format of fix slightly and update comment to match proper reality.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to commit cdda911c34, evdev only
becomes readable when the buffer contains an EV_SYN/SYN_REPORT event. If
we get a repeat or a scancode we don't have a mapping for, we never call
input_sync, and thus those events don't get reported in a timely
fashion.
For example, take an mceusb transceiver with a default rc6 keymap. Press
buttons on an rc5 remote while monitoring with ir-keytable, and you'll
see nothing. Now press a button on the rc6 remote matching the keymap.
You'll suddenly get the rc5 key scancodes, the rc6 scancode and the rc6
key spit out all at the same time.
Pressing and holding a button on a remote we do have a keymap for also
works rather unreliably right now, due to repeat events also happening
without a call to input_sync (we bail from ir_do_keydown before getting
to the point where it calls input_sync).
Easy fix though, just add two strategically placed input_sync calls
right after our input_event calls for EV_MSC, and all is well again.
Technically, we probably should have been doing this all along, its just
that it never caused any functional difference until the referenced
change went into the input layer.
input_sync once per IR signal. There was another hidden bug in the code
where we were calling input_report_key using last_keycode instead of our
just discovered keycode, which manifested with the reordering of calling
input_report_key and setting last_keycode.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Jeff Brown <jeffbrown@android.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While 0xffdc devices have their IR protocol hard-coded into the firmware
of the device, we have no known way of telling what it is if we don't
have the device's config byte already in the driver. Unknown devices
default to the imon native protocol, but might actually be rc6, so we
should set the driver up such that the user can load the rc6 keytable
from userspace and still have a working device ahead of its config byte
being added to the driver.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Another device with the 0xffdc device id, this one with 0x7e in the
config byte. Its an iMON VFD + RC6 IR, in a CoolerMaster 260 case.
Reported-by: Filip Streibl <filip@streibl.cz>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With hardware that has to use ir_raw_event_store_edge to collect IR
sample durations, we were not doing an event reset unless
IR_MAX_DURATION had passed. That's around 4 seconds. So if someone
presses up, then down, with less than 4 seconds in between, they'd get
the initial up, then up and down upon pressing down.
To fix this, I've lowered the "send a reset event" logic's threshold to
the input device's REP_DELAY (defaults to 500ms), and with an
saa7134-based GPIO-driven IR receiver in a Hauppauge HVR-1150, I get
*much* better behavior out of the remote now. Special thanks to Devin
for providing the hardware to investigate this issue.
CC: stable@kernel.org
CC: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both consumers of RC_MAP_PINNACLE_PCTV_HD send along full RC-5
scancodes, so this update makes this keymap actually *have* full
scancodes, heisted from rc-dib0700-rc5.c. This should fix out of the box
remote functionality for the Pinnacle PCTV HD 800i (cx88 pci card) and
PCTV HD Pro 801e (em28xx usb stick).
CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to the intrepid testing and debugging of Matthijs van Drunen, it
was uncovered that at least some variants of the ITE8709 need to use pnp
resource 2, rather than 0, for things to function properly. Resource 0
has a length of only 1, and if you try to bypass the pnp_port_len check
and use it anyway (with either a length of 1 or 2), the system in
question's trackpad ceased to function.
The circa lirc 0.8.7 lirc_ite8709 driver used resource 2, but the value
was (amusingly) changed to 0 by way of a patch from ITE themselves, so I
don't know if there may be variants where 0 actually *is* correct, but
at least in this case and in the original lirc_ite8709 driver author's
case, it sure looks like 2 is the right value.
This fix should probably be applied to all stable kernels with the
ite-cir driver, lest we nuke more people's trackpads.
Tested-by: Matthijs van Drunen
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As pointed out on the lirc list by Andreas Dick, initial panel key
repeat suppression wasn't working, as we had no timevals accumulated
until after the first repeat. Also add a missing locking call.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Courtesy of information from Andreas Dick on the lirc list.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Petter Selasky pointed out to me that we're leaking urbs when
mce_async_out is called. Its used both for configuring the hardware and
for transmitting IR data. In the tx case, mce_request_packet actually
allocates both a urb and the transfer buffer, neither of which was being
torn down. Do that in the tx callback.
CC: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a missing lock in fintek_suspend. Without the lock, its
possible the system will be in the middle of receiving IR (draining the
RX buffer) when we try to disable CIR interrupts.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Store the cdev pointer in struct irctl, allocated dynamically as needed,
rather than having a static array. At the same time, recycle some of the
saved memory to nudge the maximum number of lirc devices supported up a
ways -- its not that uncommon these days, now that we have the rc-core
lirc bridge driver, to see a system with at least 4 raw IR receivers.
(consider a mythtv backend with several video capture devices and the
possible need for IR transmit hardware).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Aside from the initial "hey, lets make sure we've flushed any
pre-existing data on the device" call to mce_sync_in, every other one of
the calls was entirely superfluous. Ergo, remove them all, and rename
the one and only (questionably) useful one to reflect what it really
does. Verified on both gen2 and gen3 hardware to make zero difference.
Well, except that you no longer get a bunch of urb submit failures from
the unneeded mce_sync_in calls. Oh. And move that flush to a point
*after* we've wired up the inbound urb, or it won't do squat. I have
half a mind to just remove it entirely, but someone thought it was
necessary at some point, and it doesn't seem to hurt, so lets leave it
for the time being.
This excercise took place due to insightful questions asked by Hans
Petter Selasky, about the possible reuse of the inbound urb before it
was actually availble by mce_sync_in, so thanks to him for motivating
this cleanup.
Reported-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's an SMK-device-id remote kit from I-O Data avaiable primarily in
Japan, which appears to have no tx hardware, but has rx functionality
that works with the mceusb driver by simply adding its device ID.
Reported-by: Jeremy Kwok <jeremykwok@desu.ca>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using dev_dbg is more complexity than many users are able to deal with.
Make it easier to get debug spew feedback from them by adding an mce_dbg
printk macro that spews using dev_info when debug=1 is set for the
mceusb module.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
driver to use dvb-usb-remote.
The remote(s) generates 24 bit NEC codes, lme2510 keymaps redefined.
Other minor fixes
fix le warning.
make sure frontend is detached on firmware change.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new driver for the Fintek LPC SuperIO CIR function, in the
Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so
thanks go to them for supporting this effort.
This driver started out as a copy of the nuvoton-cir driver, and was
then modified as needed for the Fintek chip. The two share many
similaries, though the buffer handling for the Fintek chip is actually
nearly identical to the mceusb buffer handling, so the parser routine is
almost a drop-in copy of the mceusb buffer parser (a candidate for being
abstracted out into shared code at some point).
This initial code drop *only* supports receive, but the hardware does
support transmit as well. I really haven't even started to look at
what's required, but my guess is that its also pretty similar to mceusb.
Most people are probably only really interested in RX anyway though, so
I think its good to get this out there even with only RX.
(Nb: there are also Fintek-made mceusb receivers, which presumably, this
chip shares CIR hardware with).
This hardware can be found on at least Jetway NC98 boards and derivative
systems, and likely others as well. Functionality was tested with an
NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge)
and NEC-ish (tivo) remotes all successful, as was lirc userspace decode
of the RC6 remote.
CC: Aaron Huang <aaron_huang@fintek.com.tw>
CC: Tom Tsai <tom_tsai@fintek.com.tw>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default REP_PERIOD is 33 ms. This doesn't make sense for IR's,
as, in general, an IR repeat scancode is provided at every 110/115ms,
depending on the RC protocol. So, increase its default, to do a
better job avoiding ghost repeat events.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
ictx->touch is intialied in imon_init_intf1, to the result of calling the
function that contains this code. Thus, in this code, input_free_device
should be called on touch itself.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression struct input_dev * x;
expression ra,rr;
position p1,p2;
@@
x = input_allocate_device@p1(...)
... when != x = rr
when != input_free_device(x,...)
when != if (...) { ... input_free_device(x,...) ...}
if(...) { ... when != x = ra
when forall
when != input_free_device(x,...)
\(return <+...x...+>; \| return@p2...; \) }
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("input_allocate_device",p1)
cocci.print_secs("input_free_device",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new rc-core device driver for the IR transceivers made by
RedRat Ltd. (http://redrat.co.uk/). It started out life as an
out-of-lirc-tree lirc driver, maintained in its own repo on sourceforge,
by Stephen Cox. He started porting it to what was then ir-core, and I
finally picked it up about two week ago and did a fairly large overhaul
on it, and its now into a state where I'm fairly comfortable submitting
it here for review and inclusion in the kernel. I'm claiming authorship
of this driver, since while it started out as Stephen's work, its
definitely a derivative work now, at 876 lines added and 1698 lines
removed since grabbing it from sourceforge. Stephen's name is retained
as secondary author though, and credited in the headers. Those
interested in seeing how the changes evolved can (at least for now) look
at this branch in my git tree:
http://git.kernel.org/?p=linux/kernel/git/jarod/linux-2.6-ir.git;a=shortlog;h=refs/heads/redrat3
That won't be around forever though, and I'm doing this as a single
commit to go into mainline. Anyway...
I've successfully tested in-kernel decode of rc5, rc6 and nec remotes,
as well as lirc userspace decode of rc5 and rc6. There are still some
quirks here to sort out with rc5 lirc userspace decode, but I'm working
with the RedRat folks themselves to figure out what's going on there
(rc5 lirc decode works, but you only get an event on key release --
in-kernel rc5 decode behaves perfectly fine). Note that lirc decode of
rc6 is working perfectly. Transmit is also working, tested by pointing
the redrat3 at an mceusb transceiver, which happily picked up the
transmitted signals and properly decoded them.
There's no default remote for this hardware, so its somewhat arbitrarily
set to use the Hauppauge RC5 keymap by default. Easily changed out by
way of ir-keytable and irrelevant if you're using lircd for decode.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <Andrew.Vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Continuing with IR transmit after resuming from suspend seems fairly
useless, given that the only place we can actually end up suspending is
after IR has been send and we're simply mdelay'ing. Lets simplify the
resume path by just waiting on tx to complete in the suspend path, then
we know we can't be transmitting on resume, and reinitialization of the
hardware registers becomes more straight-forward.
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was some rather odd spacing in a few of the ite8709-specific
functions that made it hard to read those sections of code. This is just
a simple reformatting.
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just recently acquired an Asus Eee Box PC with an onboard IR receiver
driven by ite-cir (ITE8713 sub-variant). Works out of the box with the
ite-cir driver in 2.6.39, but stops working after a suspend/resume
cycle. Its fixed by simply reinitializing registers after resume,
similar to what's done in the nuvoton-cir driver. I've not tested with
any other ITE variant, but code inspection suggests this should be safe
on all variants.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Eliminate a possible circular locking lockdep warning
- Make sure we don't try to unregister a vfd on a device w/a vga screen
- Always free imon context after devices are removed (display_close can
just error out w/no context)
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Set a default timeout (matching mceusb.c) and use
ir_raw_event_store_with_filter, which leads to better behavior when
using lirc userspace decoding with this hardware
- Fill in rx_resolution with the value we're using here (50us)
- Wire up input phys and device parent pointer
- Use device_init_wakeup() instead of device_set_wakeup_*()
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using ir_raw_event_store_with_filter() saves about 20 lines of code.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If an IR command is sent (using the LIRC userspace) to rc-loopback
which doesn't include a trailing space, the result is that the message
won't be completely decoded. In addition, "leftovers" from a previous
transmission can be left until the next one. Fix this by faking a long
silence after the end of TX data.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds preliminary IR TX capabilities to the
winbond-cir driver.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using bool instead of an int helps readability a bit.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per hardware provided to me, the Formosa Industrial Computing eHome
Infrared Receiver, 0x147a:0xe017, has no tx capability, it is rx only.
Thanks go to Paul Rae for the hardware.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to some excellent investigative work by Douglas Clowes, it was
uncovered that the older w83667hg Nuvoton chip functions with this
driver after actually enabling the CIR function via its multi-function
chip config register. The CIR and CIR wide-band sensor enable bits are
just in a different place on this hardware, so we only poke register
0x27 on 677 hardware now, and we poke register 0x2c on the 667 now.
Reported-by: Douglas Clowes <dclowes1@optusnet.com.au>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are additional chip IDs that report a PNP ID of NTN0530, which we
were refusing to load on. Instead, lets just warn if we encounter an
unknown chip, as there's a chance it will work just fine.
Also, expand the list of known hardware to include both an earlier and a
later generation chip that this driver should function with. Douglas has
an older w83667hg variant, that with a touch more work, will be
supported by this driver, and Lutz has a newer w83677hg variant that
works without any further modifications to the driver.
Reported-by: Douglas Clowes <dclowes1@optusnet.com.au>
Reported-by: Lutz Sammer <johns98@gmx.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the newly introduced KEY_IMAGES where appropriate, and standardize
on KEY_MEDIA for media center/application launcher button (such as the
Windows logo key on the Windows Media Center Ed. remotes).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kevin Baradon