Implement SPDIF bypass mode. It implies internal SoC
routing of SPDIF input signal to SPDIF output signal. The
test bed requires two boards: B1 configured in bypass mode,
and B2 to feed B1 SPDIF RX port and read B1 SPDIF TX port:
B2 TX -> B1 RX,
B2 RX <- B1 TX.
The test procedure:
a) Boot both boards
b) B2: start "arecord <spdifcard> -r 48kHz | aplay <local DAC>"
c) B2: start "aplay <spdifcard> -r 48kHz <2ch 48kHz audio file>"
d) B1: enable bypass mode:
amixer -cimxspdif cset numid=8,iface=PCM,name='Bypass Mode' on
e) B2: check DAC audio, make sure the same sample rate is used at
steps b) and c), in example above the rate is 48kHz.
f) B1: try to run "aplay" or "arecord" on imxspdif card while in
bypass mode - both must fail until bypass mode is disabled
g) B1: disable bypass mode:
amixer -cimxspdif cset numid=8,iface=PCM,name='Bypass Mode' off
h) B1: check the usual playback and capture on imxspdif card.
During this test try to set bypass mode - must not be allowed
while playback or capture is running.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1632649760-1651-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()
snd_soc_register_card()
-> snd_soc_bind_card()
-> snd_soc_add_pcm_runtime()
-> adding cpu dai
-> adding codec dai
-> adding platform component.
So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.
As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.
Fixes: a2388a498a ("ASoC: fsl: Add S/PDIF CPU DAI driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1630665006-31437-5-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When system enter suspend, the machine driver suspend callback
function will be called, then the cpu driver trigger callback
(SNDRV_PCM_TRIGGER_SUSPEND) be called, it would disable the
interrupt.
But the machine driver suspend and cpu dai driver suspend order
maybe changed, the cpu dai driver's suspend callback is called before
machine driver's suppend callback, then the interrupt is not cleared
successfully in trigger callback.
So need to clear interrupts in cpu dai driver's suspend callback
to avoid such issue.
Fixes: 9cb2b3796e ("ASoC: fsl_spdif: Add pm runtime function")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1624365084-7934-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is error message when defer probe happens:
fsl-spdif-dai 2dab0000.spdif: Unbalanced pm_runtime_enable!
Fix the error handler with pm_runtime_enable and add
fsl_spdif_remove() for pm_runtime_disable.
Fixes: 9cb2b3796e ("ASoC: fsl_spdif: Add pm runtime function")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1623392318-26304-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_get_irq() prints error message telling that interrupt is
missing, hence there is no need to duplicated that message.
Signed-off-by: Tan Zhongjun <tanzhongjun@yulong.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20210610040037.1064-1-hbut_tan@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since i.MX8MM SPDIF interface is able to capture raw data.
Add support in SPDIF driver for this functionality.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1619425444-8666-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When there is power domain bind with core clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk,but explicitly enable
clock when it is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1616579928-22428-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only way this driver can be probed is via devicetree, which always
provides driver data.
Remove the unneeded of_device_get_match_data() error check, as it
can never fail.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210118123815.1630882-6-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 88200Hz and 176400Hz sample rates support for TX.
Add 88200Hz, 176400Hz, 192000Hz sample rates support for RX.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1602557360-18795-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On i.MX8QM, there are separate interrupts for TX and RX.
As the EDMA can't be configured to swing back to first FIFO
after writing the second FIFO, so we need to force the burst
size to be 2 on i.MX8QM. And EDMA don't support to shift
the data from S24_LE to S16_LE, so the supported TX format
is also different on i.MX8QM.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1602739728-4433-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function fsl_spdif_probe() is only called with an openfirmware
platform device. Therefore there is no need to check that the passed
in device is NULL.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20200826150918.16116-1-tangbin@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add one kctl for configuring TX validity bit from user
space.
The type of this kctl is boolean:
on - Outgoing validity always set
off - Outgoing validity always clear
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1594112066-31297-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In IEC958 spec, "The validity bit is logical "0" if the
information in the main data field is reliable, and it
is logical "1" if it is not".
The default value of "ValCtrl" is zero, which means
"Outgoing Validity always set", then all the data is not
reliable, then some spdif sink device will drop the data.
So set "ValCtrl" to 1, that is to clear "Outgoing Validity"
in default.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1594112066-31297-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add pm runtime support and move clock handling there.
Close the clocks at suspend to reduce the power consumption.
fsl_spdif_suspend is replaced by pm_runtime_force_suspend.
fsl_spdif_resume is replaced by pm_runtime_force_resume.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/579c0d71e976f34f23f40daa9f1aa06c4baca2f1.1592552389.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The one difference on imx6sx platform is that the root clock
is shared with ASRC module, so we add a new flags
"shared_root_clock" which means the root clock is not independent,
then we will not do the clk_set_rate and clk_round_rate to avoid
impact ASRC module usage.
As add a new flags, we include the soc specific data struct.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/7a343edd5f8487abad248a0b862f45fd95067751.1592376770.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have snd_soc_dai/dai_stream/component_active() macro
This patch uses it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87v9ky58iy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-50-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
According to RM SPDIF STC SYSCLK_DF field is 9-bit wide, values
being in 0..511 range. Use a proper type to handle sysclk_df.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Probe deferral is to be expected during normal operation, so avoid
printing an error when it is encountered.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 64 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
rate[index] * txclk_df * 64
Addresses-Coverity-ID: 1222129 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const arrays rate on the stack, instead make them
static. Makes the object code smaller by 220 bytes:
Before:
text data bss dec hex filename
24385 9776 128 34289 85f1 sound/soc/fsl/fsl_spdif.o
After:
text data bss dec hex filename
24005 9936 128 34069 8515 sound/soc/fsl/fsl_spdif.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same as commit ce492b3b8f
Subject: drm/fsl-dcu: use flat regmap cache
Using flat regmap cache instead of RB-tree to avoid the following
lockdep warning on driver load:
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2871 lockdep_trace_alloc+0x104/0x128
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
The RB-tree regmap cache needs to allocate new space on first
writes. However, allocations in an atomic context (e.g. when a
spinlock is held) are not allowed. The function regmap_write
calls map->lock, which acquires a spinlock in the fast_io case.
Since the driver uses MMIO, the regmap bus of type regmap_mmio
is being used which has fast_io set to true.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPDIF need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to SPDIF registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
STL and STR registers are writable and not readable. So they are non volatile.
Remove them from volatile list, and add default register value for them.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power source of
modules during system suspend and resume procedure. Thus, SPDIF needs to save
all the values of registers before the system suspend and restore them after
the system resume.
The SRPC register should be volatile, LOCK bit is set by the hardware.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are too much noise about the typos for fsl's drivers. So I fix
all the typos here in this patch in almost every file I touched.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need "i" to be signed or it leads to a forever loop in the error
handling.
Fixes: fa3be9208d ('ASoC: fsl: fsl_spdif: Check for clk_prepare_enable() error')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the ssi is not the only cpu dai, there are esai, spdif, sai.
and imx_pcm_dma can be used by all of them. Especially ESAI need
a larger DMA buffer size. So Add dedicated DMA buffer for each cpu
dai.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As commit 6c8ca30eec ("ASoC: fsl_ssi: Don't try to round-up for PM
divisor calculation") mentioned that there's no more need to use a
round up work around to get a better divisor since the clk-divider
driver has been refined a lot.
So this patch applies the same modification to fsl_spdif driver.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'name' array is currently stored inside the fsl_spdif_priv private structure
only for registering the interrupt name.
This can be simplified by registering it with dev_name() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Viorel Suman