Parse SMPS configuration from IEs and configure. Without this,
SMPS is not enabled for 6 GHz band.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913175510.193005-3-jouni@codeaurora.org
Currently A-MPDU aggregation parameters are not being configured
during peer association for 6 GHz band. Hence, extract these
parameters from station's capabilities received in association
request and send to firmware. Without this, A-MPDU aggregation
is not happening in 6 GHz band.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913175510.193005-2-jouni@codeaurora.org
Add IEEE80211_HE_6GHZ_MAX_AMPDU_FACTOR as per IEEE Std 802.11ax-2021,
9.4.2.263 to use for peer max A-MPDU factor in 6 GHz band.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913175510.193005-1-jouni@codeaurora.org
Scan failure can not be recovered from when running a loop of the
following steps:
1. run scan: "iw wlan scan".
2. run command: echo assert > /sys/kernel/debug/ath11k/qca6490\ hw2.0/simulate_fw_crash
immediately after step 1.
result:
scan failed and can not recover even when wlan recovery succeeds:
command failed: Device or resource busy (-16)
reason:
When scan arrives, WMI_START_SCAN_CMDID is sent to the firmware and
function ath11k_mac_op_hw_scan() returns, then simulate_fw_crash arrives
and the scan started event does not arrive, and then it starts to do
recovery of wlan. __ath11k_mac_scan_finish() which is called from
ath11k_core_halt() is one step of recovery, it will not call
ieee80211_scan_completed() by logic currently because the scan state is
ATH11K_SCAN_STARTING. Thus it leads the scan not being completed in
mac80211, and leads all consecutive scans failing with -EBUSY in
nl80211_trigger_scan even after wlan recovery success.
Indicate scan complete with aborted flag to mac80211 for
ATH11K_SCAN_STARTING to allow recovery from scan failed with "Device or
resource busy (-16)" after wlan recovery.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-3-jouni@codeaurora.org
ath11k prints "Received scan event for unknown vdev" when doing the
following test:
1. trigger scan
2. wait 0.2 second
3. iw reg set or 11d scan complete from firmware
Reason: When iw reg set or 11d scan complete, the new country code will
be set to the firmware, and the new regdomain info indicated to ath11k,
then the new channel list will be sent to the firmware. The firmware
will cancel the current scan after receiving WMI_SCAN_CHAN_LIST_CMDID
which is used for the new channel list, and the state of ath11k is
ATH11K_SCAN_RUNNING, then ath11k_get_ar_on_scan_abort() returns NULL and
ath11k_scan_event() returns at this point and does not indicate scan
completion to mac80211.
Indicate scan completion to mac80211 and get rid of the "Received scan
event for unknown vdev" print for the above case.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-2-jouni@codeaurora.org
When wlan interface is up, 11d scan is sent to the firmware, and the
firmware needs to spend couple of seconds to complete the 11d scan. If
immediately a normal scan from user space arrives to ath11k, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath11k until the 11d scan complete. When timed
out for the scan started in ath11k, ath11k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan.
ath11k has no handler for the event and then timed out for the scan
completed in ath11k_scan_stop(), and ath11k prints the following error
message.
[ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110
Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-1-jouni@codeaurora.org
Add HTT stats support for,
29-ATH11K_DBG_HTT_EXT_STATS_PEER_CTRL_PATH_TXRX_STATS:
Used to dump the control path txrx stats for each connected peer.
Usage:
echo 29 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type
cat /sys/kernel/debug/ieee80211/phyx/netdev\:wlan0/stations/
<sta mac>/htt_peer_stats.
31-ATH11K_DBG_HTT_EXT_STATS_PDEV_TX_RATE_TXBF_STATS:
Used to dump the per pdev tx rate txbf stats.
Usage:
echo 31 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type
cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats
32-ATH11k_DBG_HTT_EXT_STATS_TXBF_OFDMA:
Used to dump the TXBF ofdma stats for all ofdma users.
Usage:
echo 32 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type
cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats
37-ATH11K_DBG_HTT_EXT_PHY_COUNTERS_AND_PHY_STATS:
Used to dump the mac and phy txrx counts and phy stats like per chain rssi
and ANI level.
Usage:
echo 37 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type
cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00486-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-6-jouni@codeaurora.org
In debugfs_htt_stats.c, masking and shifting is done to get
stats values. Instead use GENMASK and FIELD_GET to improve
code readability and maintenance.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-5-jouni@codeaurora.org
To support the HTT Stats DebugFS interface a single large buffer that
contains the stats must be provided to the DebugFS infrastructure.
In the current code, for each class of stats, the stats are first
formatted in a local on-stack buffer, and then the local buffer is
copied to the large DebugFS buffer.
This logic has a problem when, for a given class, the formatted
stats exceed the size of the on-stack buffer. When this occurs the
stats for this class is truncated. In addition, this logic is
inefficient since it introduces an unnecessary memory copy.
To address these issues, update the logic to no longer use a local
on-stack buffer, and instead write the formatted data directly into
the large DebugFS buffer.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-4-jouni@codeaurora.org
Get rid of macro HTT_DBG_OUT and replace it with scnprintf().
The macro does not do anything else. Added required new line
characters to scnprintf() for proper display.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-3-jouni@codeaurora.org
Renaming of macro is done to describe the macro functionality
better as the macro functionality is modified in next patch-sets.
No functional changes are done.
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-2-jouni@codeaurora.org
The buffer pointed to by event is not freed in case
ATH11K_FLAG_UNREGISTERING bit is set, resulting in
memory leak, so fix it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-4-jouni@codeaurora.org
Current code clears debug registers after SOC global reset performed
in ath11k_pci_sw_reset. However at that time those registers are
not accessible due to reset, thus they are actually not cleared at all.
For WCN6855, it may cause target fail to initialize. This issue can be
fixed by moving clear action ahead.
In addition, on some specific platforms, need to add delay to wait
those registers to become accessible.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-3-jouni@codeaurora.org
There are MSDUs whose length are invalid. For example,
attackers may inject on purpose truncated A-MSDUs with
invalid MSDU length.
Such MSDUs are marked with an err bit set in rx attention
tlvs, so we can check and drop them.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-2-jouni@codeaurora.org
WCN6855 has 2 phys, one is 2G, another is 5G/6G, so it should copy the
cap info of 6G band under the check of WMI_HOST_WLAN_5G_CAP as well as
for the 5G band. Some chips like QCN9074 only have 6G, not have 2G and
5G, and this 6G capability is also under WMI_HOST_WLAN_5G_CAP, so this
change will not disturb it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-4-jouni@codeaurora.org
For some chips such as WCN6855, single_pdev_only is set in struct
ath11k_hw_params which means ath11k calls ieee80211_register_hw() only
once and create only one device interface, and that device interface
supports all 2G/5G/6G channels.
ath11k_mac_setup_channels_rates() sets up the channels and it is called
for each device interface. It is called only once for single_pdev_only,
and then set up all channels for 2G/5G/6G. The logic of
ath11k_mac_setup_channels_rates() is not suitable for single_pdev_only,
it leads to all 6G channels being disabled for the device interface
which is single_pdev_only such as WCN6855.
Add channel frequency checks for the 6G band and enable the 6G channels
properly based on what is supported by the chip.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-3-jouni@codeaurora.org
WCN6855 uses single_pdev_only, so it supports both the 5G and 6G bands
in the same ath11k/pdev and it needs to enable ht_cap/vht_cap for the 5G
band, otherwise it will downgrade to non-HT mode for the 5G band. Some
chips like QCN9074 only support the 6G band, not the 5G band, and use
the flag ar->supports_6ghz which is true to discard ht_cap/vht_cap.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-2-jouni@codeaurora.org
When ath11k receives survey request, choose the 6 GHz band when enabled.
Without this, survey request does not include any 6 GHz band results,
thereby causing auto channel selection to fail.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-3-jouni@codeaurora.org
Frequency in rx status is being filled incorrectly in the 6 GHz band as
channel number received is invalid in this case which is causing packet
drops. So fix that.
Fixes: 5dcf42f8b7 ("ath11k: Use freq instead of channel number in rx path")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-2-jouni@codeaurora.org
Add support for the 6 GHz channel 2 with center frequency 5935 MHz and
operating class 136 per IEEE Std 802.11ax-2021, Table E-4.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-1-jouni@codeaurora.org
When the driver sends a peer create cmd, the firmware responds with
WMI_PEER_CREATE_CONF_EVENTID to confirm the firmware received
WMI_PEER_CREATE_CMDID. Since the peer create conf event is not handled
in ath11k_wmi_tlv_op_rx, we are getting unknown event id warning prints
during peer creation.
Add WMI_PEER_CREATE_CONF_EVENTID in wmi_tlv_event_id and handle
the same as unsupported event id under wmi logs.
warning prints:
[ 4382.230817] ath11k_pci 0000:01:00.0: Unknown eventid: 0x601a
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-9-jouni@codeaurora.org
Facing below warning prints when we do wifi down in multiple VAPs scenario.
warning print:
ath11k c000000.wifi: No VIF found for vdev 2
...
ath11k c000000.wifi: No VIF found for vdev 0
In ath11k_mac_get_arvif_by_vdev_id(), we iterate all the radio to get the
arvif for the requested vdev_id through ath11k_mac_get_arvif().
ath11k_mac_get_arvif() throws a warning message if the given vdev_id is
not found in the given radio. So to avoid the warning message, add
the allocated_vdev_map cross check against the given vdev_id before using
ath11k_mac_get_arvif() to ensure that vdev_id is allocated in the
given radio.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-8-jouni@codeaurora.org
In scenario when a peer is disassociating, there could be
multiple places where a reo cmd ring is accessed, such as
during aggregation teardown, tid queue cleanup, etc.
When this happens during firmware recovery where accessing of FW/HW
resources/registers is not recommended, accessing reo cmd ring in
this case could lead to crash or undefined behaviour.
Hence avoid this by checking for corresponding flag to avoid
accessing reo cmd ring during firmware recovery.
Sample crash:
[ 3936.456050] Unhandled fault: imprecise external abort (0x1c06) at 0x54bb842a
[ 3936.456411] WARN: Access Violation!!!, Run "cat /sys/kernel/debug/qcom_debug_logs/tz_log" for more details
[ 3936.467997] pgd = b4474000
[ 3936.477440] [54bb842a] *pgd=6fa61831, *pte=7f95d59f, *ppte=7f95de7e
<snip>
[ 3937.177436] [<8030ab10>] (_raw_spin_unlock_bh) from [<7f5e9eb8>] (ath11k_hal_reo_cmd_send+0x440/0x458 [ath11k])
[ 3937.185730] [<7f5e9eb8>] (ath11k_hal_reo_cmd_send [ath11k]) from [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd+0x2c/0xcc [ath11k])
[ 3937.195524] [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd [ath11k]) from [<7f602f10>] (ath11k_peer_rx_tid_reo_update+0x84/0xbc [ath11k])
[ 3937.206984] [<7f602f10>] (ath11k_peer_rx_tid_reo_update [ath11k]) from [<7f605a9c>] (ath11k_dp_rx_ampdu_stop+0xa8/0x130 [ath11k])
[ 3937.218532] [<7f605a9c>] (ath11k_dp_rx_ampdu_stop [ath11k]) from [<7f5f6730>] (ath11k_mac_op_ampdu_action+0x6c/0x98 [ath11k])
[ 3937.230250] [<7f5f6730>] (ath11k_mac_op_ampdu_action [ath11k]) from [<c7b6e890>] (___ieee80211_stop_rx_ba_session+0x98/0x144 [mac80211])
[ 3937.241499] [<c7b6e890>] (___ieee80211_stop_rx_ba_session [mac80211]) from [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions+0x4c/0xf4 [)
[ 3937.253833] [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions [mac80211]) from [<c7b63460>] (ieee80211_sta_eosp+0x5b8/0x960 [mac80211])
[ 3937.266764] [<c7b63460>] (ieee80211_sta_eosp [mac80211]) from [<c7b66da8>] (__sta_info_flush+0x9c/0x134 [mac80211])
[ 3937.278826] [<c7b66da8>] (__sta_info_flush [mac80211]) from [<c7b7bd00>] (ieee80211_stop_ap+0x14c/0x28c [mac80211])
[ 3937.289240] [<c7b7bd00>] (ieee80211_stop_ap [mac80211]) from [<7f509cf0>] (__cfg80211_stop_ap+0x4c/0xd8 [cfg80211])
[ 3937.299629] [<7f509cf0>] (__cfg80211_stop_ap [cfg80211]) from [<7f4dddec>] (cfg80211_leave+0x24/0x30 [cfg80211])
[ 3937.310041] [<7f4dddec>] (cfg80211_leave [cfg80211]) from [<7f4de03c>] (cfg80211_netdev_notifier_call+0x174/0x48c [cfg80211])
[ 3937.320457] [<7f4de03c>] (cfg80211_netdev_notifier_call [cfg80211]) from [<80339928>] (notifier_call_chain+0x40/0x68)
[ 3937.331636] [<80339928>] (notifier_call_chain) from [<803399a8>] (raw_notifier_call_chain+0x14/0x1c)
[ 3937.342221] [<803399a8>] (raw_notifier_call_chain) from [<8073bb00>] (call_netdevice_notifiers+0xc/0x14)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01240-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-7-jouni@codeaurora.org
Firmware crash is seen randomly, because of sending wrong vdev_id
in vdev_create command. This is due to free_vdev_map value being 0.
free_vdev_map is getting assigned after ieee80211_register_hw. In
some race conditions, add_interface api is getting called before
assigning value to free_vdev_map. Fix this by assigning free_vdev_map
before ieee80211_register_hw.
Also, moved ar->cc_freq_hz and ar->txmgmt_idr initialization before
ieee80211_register_hw to avoid such race conditions.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00948-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-6-jouni@codeaurora.org
Firmware blocks all data traffic until the key is plumbed. But, with
software encryption mode, key is never plumbed to firmware. Due to this,
a traffic failure in software encryption mode has been observed. Hence,
firmware has introduced a flag to differentiate software encryption
mode. This flag can be passed during vdev_start command.
Enable WMI_VDEV_START_HW_ENCRYPTION_DISABLED flag in vdev_start command
to notify firmware to disable hardware encryption for a vdev. This is set
if raw mode software encryption is enabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-5-jouni@codeaurora.org
Whenever ath11k is bootup with a user country already set, cfg80211
notifies this country info to ath11k soon after registration, where the
notification is sent to the firmware for fetching the rules of this user
country input.
Multiple race conditions could be seen in this scenario where a new
request is either lost as pointed in [1] or a new regd overwrites the
default regd provided by the firmware during bootup. Note that, the
default regd is used for intersection purpose and hence it should not be
overwritten.
The main reason as pointed by [1] is the usage of ATH11K_FLAG_REGISTERED
flag which is updated after completion of core registration, whereas the
reg notification from cfg80211 and wmi events for the corresponding
request can happen much before that. Since the ATH11K_FLAG_REGISTERED is
currently used to determine if the event containing reg rules belong to
default regd or for user request, there is a possibility of the default
regd getting overwritten.
Since the default reg rules will be received only once per pdev on
firmware load, the above flag based check can be replaced with a check
to see if default_regd is already set, so that we can now always update
the new_regd. Also if the new_regd is set, this will be always used to
update the reg rules for the registered phy.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/1829665.1PRlr7bOQj@ripper/
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-4-jouni@codeaurora.org
During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.
See below snap for example,
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC
In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.
This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Update the fields of pdev tx and tx firmware stats structure.
Missing fields resulted in wrong fw stats to be displayed as below.
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/
ipq8074\ hw2.0/mac0/fw_stats/pdev_stats | grep Illegal
Illegal rate phy errors 36839112
Note that this struct was missing its members from initial driver
support and this change doesn't introduce/modify the structure for
firmware changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-2-jouni@codeaurora.org
Fix sending rx_buf_sz to ath11k_dp_tx_htt_rx_filter_setup()
to enable pktlog full or lite mode. Depending on mode update the
trace buffer with log type full/lite.
Pktlog lite is a lighter version of pktlog. This can be used to capture
PPDU stats. These are useful for firmware performance debugging.
pktlog lite dumps are enabled using,
echo "0x0 1" > ath11k/IPQ8074 hw2.0/mac0/pktlog_filter
Tested On: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01233-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-1-jouni@codeaurora.org
Add support for rx decapsulation offload by advertising
the support to mac80211 during registration. Also ensure
the frames have the RX_FLAG_8023 flag set in decap offload
frames before passing to mac80211.
Since the packets delivered to the driver are in 802.3 format, these
can be sent to the network core with minimal processing in mac80211.
This helps in releasing some CPU cycles in the host processor and
thereby improving the performance.
Two exceptions are made before passing decap frames, one is
for EAPOL packets since mac80211 8023 fast rx for the sta
is set only after authorization, other case is for multicast
packets to validate PN in mac80211. In both the cases the
decap frames are converted to 80211 frame and sent to mac80211.
Ethernet decap can be enabled by using frame_mode modparam:
insmod ath11k frame_mode=2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00844-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721204217.120572-1-jouni@codeaurora.org
The ath11k_dbring_bufs_replenish() and ath11k_dbring_fill_bufs()
take a "gfp" parameter but they since they take spinlocks, the
allocations they do have to be atomic. This causes a bug because
ath11k_dbring_buf_setup passes GFP_KERNEL for the gfp flags.
The fix is to use GFP_ATOMIC and remove the unused parameters.
Fixes: bd6478559e ("ath11k: Add direct buffer ring support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812070434.GE31863@kili
qmi tries to allocate a large contiguous dma memory at first,
on the AMD Ryzen platform it fails, then retries with small slices.
So set flag GFP_NOWARN to avoid flooding dmesg.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823063258.37747-1-aaron.ma@canonical.com
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members"[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code a bit according to the use of a flexible-array member in
struct scan_chan_list_params instead of a one-element array, and use the
struct_size() helper.
Also, save 25 (too many) bytes that were being allocated:
$ pahole -C channel_param drivers/net/wireless/ath/ath11k/reg.o
struct channel_param {
u8 chan_id; /* 0 1 */
u8 pwr; /* 1 1 */
u32 mhz; /* 2 4 */
/* Bitfield combined with next fields */
u32 half_rate:1; /* 4:16 4 */
u32 quarter_rate:1; /* 4:17 4 */
u32 dfs_set:1; /* 4:18 4 */
u32 dfs_set_cfreq2:1; /* 4:19 4 */
u32 is_chan_passive:1; /* 4:20 4 */
u32 allow_ht:1; /* 4:21 4 */
u32 allow_vht:1; /* 4:22 4 */
u32 allow_he:1; /* 4:23 4 */
u32 set_agile:1; /* 4:24 4 */
u32 psc_channel:1; /* 4:25 4 */
/* XXX 6 bits hole, try to pack */
u32 phy_mode; /* 8 4 */
u32 cfreq1; /* 12 4 */
u32 cfreq2; /* 16 4 */
char maxpower; /* 20 1 */
char minpower; /* 21 1 */
char maxregpower; /* 22 1 */
u8 antennamax; /* 23 1 */
u8 reg_class_id; /* 24 1 */
/* size: 25, cachelines: 1, members: 21 */
/* sum members: 23 */
/* sum bitfield members: 10 bits, bit holes: 1, sum bit holes: 6 bits */
/* last cacheline: 25 bytes */
} __attribute__((__packed__));
as previously, sizeof(struct scan_chan_list_params) was 32 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[1]; /* 6 25 */
/* size: 32, cachelines: 1, members: 3 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
and now with the flexible array transformation it is just 8 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[]; /* 6 0 */
/* size: 8, cachelines: 1, members: 3 */
/* padding: 2 */
/* last cacheline: 8 bytes */
};
This helps with the ongoing efforts to globally enable -Warray-bounds and
get us closer to being able to tighten the FORTIFY_SOURCE routines on
memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823172159.GA25800@embeddedor
Firmware updates EEPROM support capability in QMI FW caps, send QMI BDF
download request message with file type EEPROM, to get caldata download
from EEPROM. Firmware takes more time to update cal data from EEPROM, so
increase QMI timeout.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-5-jouni@codeaurora.org
In current code, AHB/PCI uses two separate functions to download
BDF file. Refactor code and make a common function to send QMI BDF
download request for both AHB and PCI devices. This patch has no
functional change.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-3-jouni@codeaurora.org
Reuse board_size from hw_params, add cal_offset to hw params.
This patch is clean up only, there is no change in functionality.
cal_size was unused, so remove that.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-2-jouni@codeaurora.org
gcc-11 with the kernel address sanitizer prints a warning for this
driver:
In function 'ath11k_peer_assoc_h_vht',
inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:1632:2:
drivers/net/wireless/ath/ath11k/mac.c:1164:13: error: 'ath11k_peer_assoc_h_vht_masked' reading 16 bytes from a region of size 4 [-Werror=stringop-overread]
1164 | if (ath11k_peer_assoc_h_vht_masked(vht_mcs_mask))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath11k/mac.c: In function 'ath11k_peer_assoc_prepare':
drivers/net/wireless/ath/ath11k/mac.c:1164:13: note: referencing argument 1 of type 'const u16 *' {aka 'const short unsigned int *'}
drivers/net/wireless/ath/ath11k/mac.c:969:1: note: in a call to function 'ath11k_peer_assoc_h_vht_masked'
969 | ath11k_peer_assoc_h_vht_masked(const u16 vht_mcs_mask[NL80211_VHT_NSS_MAX])
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
According to analysis from gcc developers, this is a glitch in the
way gcc tracks the size of struct members. This should really get
fixed in gcc, but it's also easy to work around this instance
by changing the function prototype to no include the length of
the array.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99673
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210322160253.4032422-5-arnd@kernel.org
Populate the below hw parameters as per the QCN9074 support
1. FFT bin size as two bytes
2. Maximum FFT bin count as 1024
3. Summary report pad size as 16
4. FFT report header length as 24
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-5-jouni@codeaurora.org
User was not able to configure the spectral with the FFT bin count 32.
In all supported platforms, the expected minimum FFT bin count is 32 but
it was wrongly defined as 64. This restrict the user to not configure
down to the actually supported minimum FFT bin count. So update the
minimum FFT bin count as 32.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-4-jouni@codeaurora.org
Below parameters have been identified as configurable across the platforms.
So to scale the spectral across the platforms, move these parameter
into hw param.
1. Maximum FFT bins
2. Summary report pad size
3. FFT report header length
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-3-jouni@codeaurora.org
In IPQ8074, actual FFT bin size is two bytes but hardware reports it
with extra pad size of two bytes for each FFT bin. So finally each FFT
bin advertise as four bytes size in the collected data. This FFT pad is
not advertised in IPQ6018 platform. To accommodate this different
behavior across the platforms, introduce the hw param fft_pad_sz and use
it in spectral process. Also group all the spectral params under the new
structure in hw param structure for scalable in future.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-2-jouni@codeaurora.org
For 160 MHz, nss_ratio_enabled flag is added to indicate firmware
supports sending NSS ratio information from firmware as a part of
service ready ext event. Extract this NSS ratio info from service
ready ext event and save this information in ath11k_pdev_cap to
calculate NSS ratio.
Current firmware configurations support two types of NSS ratio
which is WMI_NSS_RATIO_1_NSS for QCN9074 and WMI_NSS_RATIO_1BY2_NSS
for IPQ8074. Based on this two configuration, max supported
NSS getting calculated.
Move ath11k_peer_assoc_h_phymode() before ath11k_peer_assoc_h_vht()
to get arg->peer_phymode updated.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-00097-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Co-developed-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721173615.75637-2-jouni@codeaurora.org
Support setting fixed HE rate/gi/ltf values that we are now able to send
to the kernel using nl80211. The added code is reusing parts of the
existing code path already used for HT/VHT. The new helpers are
symmetric to how we do it for HT/VHT.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00235-QCAHKSWPL_SILICONZ-1
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Co-developed-by: Pradeep Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721173615.75637-1-jouni@codeaurora.org
If monitor interface is enabled in co-exist mode, only local traffic are
captured. It's caused by missing monitor vdev in co-exist mode. So,
monitor mode clean up is done with separate Monitor APIs. For this,
introduce flags monitor_started and monitor_vdev_created.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01725-QCAHKSWPL_SILICONZ-1
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-4-jouni@codeaurora.org
Add separate APIs for monitor_vdev_create/monitor_vdev_delete
and monitor_vdev_start/monitor_vdev_stop.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01725-QCAHKSWPL_SILICONZ-1
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-3-jouni@codeaurora.org
This is to prepare for monitor mode clean up.
No functional changes are done.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-2-jouni@codeaurora.org
Idle Mode Power Save (IMPS) is a power saving mechanism which when called
by wcn36xx will cause the radio hardware to enter power collapse.
This particular call maps nicely to a simple conjunction/disjunction around
IEEE80211_CONF_CHANGE_IDLE and IEEE80211_CONF_IDLE.
Here we enter idle when we are not associated with an AP. The kernel will
incrementally toggle idle on/off in the process of trying to establish a
connection, thus saving power until we are connected to the AP again, at
which point we give way to BMPS if power_save is on.
We've validated that with IMPS an apq8039 device which has the wcn36xx
module loaded but, has not authenticated with an AP will get to VMIN on
suspend and will not without IMPS.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909153320.2624649-1-bryan.odonoghue@linaro.org
Qcom documents suggest passing of negative values to the dump command,
however currently we convert from string to u32 not s32, so we cannot pass
a two's complement value to the firmware in this way.
There is in fact only one parameter which takes a two's complement value
<tigger threshold> in the antenna diversity switch command.
Downstream:
iwpriv wlan0 dump 71 3 <schedule period> <trigger threshold> <hysteresis value>
Upstream:
echo "71 3 <schedule period> <trigger threshold> <hysteresis value>" > /sys/kernel/debug/ieee80211/phy0/wcn36xx/dump
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-3-bryan.odonoghue@linaro.org
We have been tracking a strange bug with Antenna Diversity Switching (ADS)
on wcn3680b for a while.
ADS is configured like this:
A. Via a firmware configuration table baked into the NV area.
1. Defines if ADS is enabled.
2. Defines which GPIOs are connected to which antenna enable pin.
3. Defines which antenna/GPIO is primary and which is secondary.
B. WCN36XX_CFG_VAL(ANTENNA_DIVERSITY, N)
N is a bitmask of available antenna.
Setting N to 3 indicates a bitmask of enabled antenna (1 | 2).
Obviously then we can set N to 1 or N to 2 to fix to a particular
antenna and disable antenna diversity.
C. WCN36XX_CFG_VAL(ASD_PROBE_INTERVAL, XX)
XX is the number of beacons between each antenna RSSI check.
Setting this value to 50 means, every 50 received beacons, run the
ADS algorithm.
D. WCN36XX_CFG_VAL(ASD_TRIGGER_THRESHOLD, YY)
YY is a two's complement integer which specifies the RSSI decibel
threshold below which ADS will run.
We default to -60db here, meaning a measured RSSI <= -60db will
trigger an ADS probe.
E. WCN36XX_CFG_VAL(ASD_RTT_RSSI_HYST_THRESHOLD, Z)
Z is a hysteresis value, indicating a delta which the RSSI must
exceed for the antenna switch to be valid.
For example if HYST_THRESHOLD == 3 AntennaId1-RSSI == -60db and
AntennaId-2-RSSI == -58db then firmware will not switch antenna.
The threshold needs to be -57db or better to satisfy the criteria.
F. A firmware feature bit also exists ANTENNA_DIVERSITY_SELECTION.
This feature bit is used by the firmware to report if
ANTENNA_DIVERSITY_SELECTION is supported. The host is not required to
toggle this bit to enable or disable ADS.
ADS works like this:
A. Every XX beacons the firmware switches to or remains on the primary
antenna.
B. The firmware then sends a Request-To-Send (RTS) packet to the AP.
C. The firmware waits for a Clear-To-Send (CTS) response from the AP.
D. The firmware then notes the received RSSI on the CTS packet.
E. The firmware then repeats steps A-D on the secondary antenna.
F. Subsequently if the RSSI on the measured antenna is better than
ASD_TRIGGER_THRESHOLD + the active antenna's RSSI then the
measured antenna becomes the active antenna.
G. If RSSI rises past ASD_TRIGGER_THRESHOLD then ADS doesn't run at
all even if there is a substantially better RSSI on the alternative
antenna.
What we have been observing is that the RTS packet is being sent but the
MAC address is a byte-swapped version of the target MAC. The ADS/RTS MAC is
corrupted only when the link is encrypted, if the AP is open the RTS MAC is
correct. Similarly if we configure the firmware to an RTS/CTS sequence for
regular data - the transmitted RTS MAC is correctly formatted.
Internally the wcn36xx firmware uses the indexes in the SMD commands to
populate and extract data from specific entries in an STA lookup table. The
AP's MAC appears a number of times in different indexes within this lookup
table, so the MAC address extracted for the data-transmit RTS and the MAC
address extracted for the ADS/RTS packet are not the same STA table index.
Our analysis indicates the relevant firmware STA table index is
"bssSelfStaIdx".
There is an STA populate function responsible for formatting the MAC
address of the bssSelfStaIdx including byte-swapping the MAC address.
Its clear then that the required STA populate command did not run for
bssSelfStaIdx.
So taking a look at the sequence of SMD commands sent to the firmware we
see the following downstream when moving from an unencrypted to encrypted
BSS setup.
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_CONFIG_STA_REQ
- WLAN_HAL_SET_STAKEY_REQ
Upstream in wcn36xx we have
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_SET_STAKEY_REQ
The solution then is to add the missing WLAN_HAL_CONFIG_STA_REQ between
WLAN_HAL_CONFIG_BSS_REQ and WLAN_HAL_SET_STAKEY_REQ.
No surprise WLAN_HAL_CONFIG_STA_REQ is the routine responsible for
populating the STA lookup table in the firmware and once done the MAC sent
by the ADS routine is in the correct byte-order.
This bug is apparent with ADS but it is also the case that any other
firmware routine that depends on the "bssSelfStaIdx" would retrieve
malformed data on an encrypted link.
Fixes: 3e977c5c52 ("wcn36xx: Define wcn3680 specific firmware parameters")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-2-bryan.odonoghue@linaro.org
Pradeep Kumar Chitrapu