According to my schematics, on Lite5200 board ethernet phy uses address
0 (all ADDR lines are pulled down). With this change I can talk to
onboard phy (LXT971) and correctly use autonegotiation.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When going to standby mode mpc code maps the whole soc5200 node
to access warious MBAR registers. However as of_iomap uses 'reg'
property of device node, only small part of MBAR is getting mapped.
Thus pm code gets oops when trying to access high parts of MBAR.
As a way to overcome this, make mpc52xx_pm_prepare() explicitly
map whole MBAR (0xc0000).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch probes for the Super IO chip and reserves the IO range when
found. It avoids enabling the IDE interface on the Avanti family, since
none has IDE. It enables the Enhanced Parallel Port v1.9 feature.
Signed-off-by: Morten H. Larsen <m-larsen@post6.tele.dk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
mpic_resume() on G5 macs blindly dereferences mpic->fixups, but
it may legitimately be NULL (as on PowerMac7,2). Add an explicit
check.
This fixes suspend-to-disk with one processor (maxcpus=1) for me.
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When trying to flash a machine via the update_flash command, Anton received the
following error:
Restarting system.
FLASH: kernel bug...flash list header addr above 4GB
The code in question has a comment that the flash list should be in
the kernel data and therefore under 4GB:
/* NOTE: the "first" block list is a global var with no data
* blocks in the kernel data segment. We do this because
* we want to ensure this block_list addr is under 4GB.
*/
Unfortunately the Kconfig option is marked tristate which means the variable
may not be in the kernel data and could be above 4GB.
Instead of relying on the data segment being below 4GB, use the static
data buffer allocated by the kernel for use by rtas. Since we don't
use the header struct directly anymore, convert it to a simple pointer.
Reported-By: Anton Blanchard <anton@samba.org>
Signed-Off-By: Milton Miller <miltonm@bga.com
Tested-By: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Irq stacks provide an essential protection from stack overflows through
external interrupts, at the cost of two additionals stacks per CPU.
Enable them unconditionally to simplify the kernel build and prevent
people from accidentally disabling them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
kexec_perpare_cpus_wait() iterates i through NR_CPUS to check
paca[i].kexec_state of each to make sure they have quiesced.
However now we have dynamic PACA allocation, paca[NR_CPUS] is not necessarily
valid and we overrun the array; spurious "cpu is not possible, ignoring"
errors result. This patch iterates for_each_online_cpu so stays
within the bounds of paca[] -- and every CPU is now 'possible'.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
On 5 May 2010 21:33, "Anton Blanchard" <anton@samba.org> wrote:
CONFIG_SYSFS_DEPRECATED can cause issues with newer distros and should not
be required for any distro in the last 3 or 4 years, so disable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It was used in the dim distant past for adding initrds to images
for legacy iSeries, but it's not even used for that now that we
have initramfs. So remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing boot fails on some System p machines when using the kdump
crashkernel= boot option. The default kdump base address is 32MB, so if we
reserve 256MB for kdump then we reserve all of the RMO except the first 32MB.
We really want kdump to reserve some memory in the RMO and most of it
elsewhere but that will require more significant changes. For now we can shift
the default base address to 64MB when CONFIG_PPC64 and CONFIG_RELOCATABLE are
set. This isn't quite correct since what we really care about is the kdump
kernel is relocatable, but we already make the assumption that base kernel
and kdump kernel have the same CONFIG_RELOCATABLE setting, eg:
#ifndef CONFIG_RELOCATABLE
if (crashk_res.start != KDUMP_KERNELBASE)
printk("Crash kernel location must be 0x%x\n",
KDUMP_KERNELBASE);
...
RTAS is instantiated towards the top of our RMO, so if we were to go any
higher we risk not having enough RMO memory for the kdump kernel on boxes
with a 128MB RMO.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CONFIG_HIGHPTE doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PMU is not tested and enabled on MMP architecture at this moment,
the device IRQ number, IRQ_PMU depends on ARCH_PXA. Build PMU only
for ARCH_PXA.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since commit a48c24a696, the
camera is not working anymore.
After the v4l2 migration, the mt9m111 camera board
information was not passed to the i2c layer anymore, but
stored for future use of v4l2 (through soc_camera).
Because mioa701_i2c_devices[] was tagged as "__initdata",
and because after the v4l2 migration, the new structure
"iclink" references it, the mt9m111 driver is not probed
anymore, as part of "iclink" is not valid (discarded after
kernel init).
Although there is not compilation error, nor runtime oops,
this patch restores a working camera on the mioa701 board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch fixes flash layout to it's final version. Also, I fixed the
authorship information of this file as it's been totally reworked since Ken
released his last version.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
gpio must be int, not u16, otherwise -1 isn't recognised
by gpio_is_valid().
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
subtree_max_end that was recently added to struct memtype was not getting
properly initialized resulting in
WARNING: kmemcheck: Caught 64-bit read from uninitialized memory
in memtype_rb_augment_cb()
reported here
https://bugzilla.kernel.org/show_bug.cgi?id=16092
This change fixes the problem.
Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Tested-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
LKML-Reference: <1276217101-11515-1-git-send-email-venki@google.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Yannick found that video does not work with 2.6.34. The cause of this
bug was that the BIOS had assigned the wrong range to the PCI bridge
above the video device. Before 2.6.34 the kernel would have shrunk
the size of the bridge window, but since
d65245c PCI: don't shrink bridge resources
the kernel will avoid shrinking BIOS ranges.
So zero out the old range if we fail to claim it at boot time; this will
cause us to allocate a new range at startup, restoring the 2.6.34
behavior.
Fixes regression https://bugzilla.kernel.org/show_bug.cgi?id=16009.
Reported-by: Yannick <yannick.roehlly@free.fr>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apparently UML cannot stomach callee reg-saving trickery
introduced with d61931d89b
(x86: Add optimized popcnt variants) and oopses during boot:
http://marc.info/?l=linux-kernel&m=127522065202435&w=2
Redirect arch_hweight.h include from the x86 portion to the generic
arch_hweight.h which is a fallback to the software hweight routines.
LKML-Reference: <201005271944.09541.toralf.foerster@gmx.de>
Signed-off-by: Borislav Petkov <bp@alien8.de>
LKML-Reference: <4C0F4B00.4090307@panasas.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Catch missing conversion to the register structure "glove box" scheme.
Found by gcc 4.6's new warnings.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20100610111040.F1781B1A2B@basil.firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'kvm-updates/2.6.35' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: read apic->irr with ioapic lock held
KVM: ia64: Add missing spin_unlock in kvm_arch_hardware_enable()
KVM: Fix order passed to iommu_unmap
KVM: MMU: Remove user access when allowing kernel access to gpte.w=0 page
KVM: MMU: invalidate and flush on spte small->large page size change
KVM: SVM: Implement workaround for Erratum 383
KVM: SVM: Handle MCEs early in the vmexit process
KVM: powerpc: fix init/exit annotation
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix null pointer deref with SEND_SIG_FORCED
perf: Fix signed comparison in perf_adjust_period()
powerpc/oprofile: fix potential buffer overrun in op_model_cell.c
perf symbols: Set the DSO long name when using symbol_conf.vmlinux_name
Saving platform non-volatile state may be required for suspend to RAM as
well as hibernation. Move it to more generic code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6164/1: Add kto and kfrom to input operands list.
ARM: 6166/1: Proper prefetch abort handling on pre-ARMv6
ARM: 6165/1: trap overflows on highmem pages from kmap_atomic when debugging
ARM: 6152/1: ux500 make it possible to disable localtimers
[ARM] pxa/spitz: Correctly register WM8750
[ARM] pxa/palmtc: storage class should be before const qualifier
ARM: 6146/1: sa1111: Prevent deadlock in resume path
ARM: 6145/1: ux500 MTU clockrate correction
ARM: 6144/1: TCM memory bug freeing bug
ARM: VFP: Fix vfp_put_double() for d16-d31
Checking to se if the IO daisy chain is enabled should be checking the
PM_WKEN register, not the PM_WKST register. Reading PM_WKST tells us
if an event occurred, not whether or not it is enabled.
Apparently, we've been lucky until now in that a pending event has not
been there during enable. However, on 3630/Zoom3, I noticed because
of the WARN that this timeout was always happening.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The addition of the new debounce code (commit
168ef3d9a5) broke the auto-disable of
debounce clocks on idle by forgetting to update the debounce clock
enable mask.
Add back the updating of bank->dbck_enable_mask so debounce clocks are
auto-disabled.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The kernel timer queue is being run currently from a GP timer running in a one
shot mode, which works in a way that when it expires, it will also stop.
Usually during this situation, the interrupt handler will ack the interrupt,
load a new value to the timer and start it again. During suspend, the
situation is slightly different, as we disable interrupts just before
timekeeping is suspended, which leaves a small window where the timer can
expire before it is stopped, and will leave the interrupt flag pending.
This pending interrupt will prevent ARM sleep entry, thus now we ack it always
when we are attempting to stop a timer.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: removed the ifdef to make the patch cover omap1 also]
Signed-off-by: Tony Lindgren <tony@atomide.com>
When I introduced the global variable gsi_end I thought gsi_end on
io_apics was one past the end of the gsi range for the io_apic. After
it was pointed out the the range on io_apics was inclusive I changed
my global variable to match. That was a big mistake. Inclusive
semantics without a range start cannot describe the case when no gsi's
are allocated. Describing the case where no gsi's are allocated is
important in sfi.c and mpparse.c so that we can assign gsi numbers
instead of blindly copying the gsi assignments the BIOS has done as we
do in the acpi case.
To keep from getting the global variable confused with the gsi range
end rename it gsi_top.
To allow describing the case where no gsi's are allocated have gsi_top
be one place the highest gsi number seen in the system.
This fixes an off by one bug in sfi.c:
Reported-by: jacob pan <jacob.jun.pan@linux.intel.com>
This fixes the same off by one bug in mpparse.c:
This fixes an off unreachable by one bug in acpi/boot.c:irq_to_gsi
Reported-by: Yinghai <yinghai.lu@oracle.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <m17hm9jre7.fsf_-_@fess.ebiederm.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Reinstate the null behaviour that the in-kernel gdbstub had for the GDB
remote protocol 'p' command (retrieve a single register value) prior to
commit 7ca8b9c0da ("frv: extend gdbstub to support more features of
gdb").
Before that, the 'p' command just returned an empty reply, which causes
gdb to then go and use the 'g' command. However, since that commit, the
'p' command returns an error string, which causes gdb to abort its
connection to the target.
Not all gdb versions are affected, some use try 'g' first, and if that
works, don't bother with 'p', and so don't see the error.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a spin_unlock missing on the error path.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* spin_lock(E1,...);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* spin_unlock(E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Avi Kivity <avi@redhat.com>
If cr0.wp=0, we have to allow the guest kernel access to a page with pte.w=0.
We do that by setting spte.w=1, since the host cr0.wp must remain set so the
host can write protect pages. Once we allow write access, we must remove
user access otherwise we mistakenly allow the user to write the page.
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Always invalidate spte and flush TLBs when changing page size, to make
sure different sized translations for the same address are never cached
in a CPU's TLB.
Currently the only case where this occurs is when a non-leaf spte pointer is
overwritten by a leaf, large spte entry. This can happen after dirty
logging is disabled on a memslot, for example.
Noticed by Andrea.
KVM-Stable-Tag
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements a workaround for AMD erratum 383 into
KVM. Without this erratum fix it is possible for a guest to
kill the host machine. This patch implements the suggested
workaround for hypervisors which will be published by the
next revision guide update.
[jan: fix overflow warning on i386]
[xiao: fix unused variable warning]
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch moves handling of the MC vmexits to an earlier
point in the vmexit. The handle_exit function is too late
because the vcpu might alreadry have changed its physical
cpu.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvmppc_e500_exit() is a module_exit function, so it should be tagged
with __exit, not __init. The incorrect annotation was added by commit
2986b8c72c.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The commit "asm-generic: add NEED_SG_DMA_LENGTH to define sg_dma_len()"
18e98307de broke microblaze compilation.
dma_direct_map_sg() sets sg->dma_length, however microblaze doesn't
set NEED_SG_DMA_LENGTH so scatterlist strcutres doesn't include
dma_length.
sg->dma_length is always equal to sg->length on microblaze. So we
don't need to set set dma_length, that is, microblaze can simply use
sg->length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Michal Simek <monstr@monstr.eu>
The commit "mm: Move ARCH_SLAB_MINALIGN and
ARCH_KMALLOC_MINALIGN to <linux/slab_def.h>"
1f0ce8b3dd which moved the ARCH_SLAB_MINALIGN
default into the global header broke FLAT for Microblaze.
Error message:
slab error in verify_redzone_free(): cache `idr_layer_cache':
memory outside object was overwritten
Signed-off-by: Michal Simek <monstr@monstr.eu>
Commit 48feb33747 arm: omap: switch over to gpio_set_debounce caused
"undefined reference to omap_set_gpio_debounce" build error.
The fix is to use the generic gpiolib function.
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes following error,
CC arch/arm/mach-omap2/usb-ehci.o
arch/arm/mach-omap2/usb-ehci.c:263: error: implicit declaration of function
'DMA_BIT_MASK'
arch/arm/mach-omap2/usb-ehci.c:263: error: initializer element is not constant
make[1]: *** [arch/arm/mach-omap2/usb-ehci.o] Error 1
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The memory allocated for sgt structure is not freed on error
when sg_alloc_table is called in sgtable_alloc().
Signed-off-by: Satish Kumar <x0124230@ti.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Cc: Vimal Singh <vimal.newwork@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgen <tony@atomide.com>
When functions incoming parameters are not in input operands list gcc
4.5 does not load the parameters into registers before calling this
function but the inline assembly assumes valid addresses inside this
function. This breaks the code because r0 and r1 are invalid when
execution enters v4wb_copy_user_page ()
Also the constant needs to be used as third input operand so account
for that as well.
Tested on qemu arm.
CC: <stable@kernel.org>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instruction faults on pre-ARMv6 CPUs are interpreted as
a 'translation fault', but do_translation_fault doesn't
handle well if user mode trying to run instruction above
TASK_SIZE, and result in the infinite retry of that
instruction.
CC: <stable@kernel.org>
Signed-off-by: Anfei Zhou <anfei.zhou@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_DEBUG_HIGHMEM is used, the fixmap entry used for a highmem page
by kmap_atomic() is always cleared by kunmap_atomic(). This helps find
bad usages such as dereferences after the unmap, or overflow into the
adjacent fixmap areas.
But this debugging aid is completely bypassed when a kmap for the same
page already exists as the kmap is reused instead. ON VIVT systems we
have no choice but to reuse that kmap due to cache coherency issues,
but on non VIVT systems we should always force the fixmap usage when
debugging is active.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently compilation of ux500 fails if you deselect the kernel
feature for localtimers.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The containing function is called from several places. At one of them, in
the function __sigp_stop, the spin lock &fi->lock is held.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@gfp exists@
identifier fn;
position p;
@@
fn(...) {
... when != spin_unlock
when any
GFP_KERNEL@p
... when any
}
@locked@
identifier gfp.fn;
@@
spin_lock(...)
... when != spin_unlock
fn(...)
@depends on locked@
position gfp.p;
@@
- GFP_KERNEL@p
+ GFP_ATOMIC
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When unregistering kprobes, kprobes calls module_free() and
always passes NULL for the mod parameter. Add a check to
prevent NULL pointer dereferences.
See commit 740a8de079 for more details.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add missing GFP flag to memory allocations. The part in cio only
changes a comment.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As Ingo pointed out in a separate patch, we should be using __ASSEMBLY__.
Make that the case in pgtable headers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
LKML-Reference: <20100605114042.35ac69c1@dev.queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
At some point this was exposed (not sure how),
linux-2.6/arch/arm/mach-msm/dma.c:92: error: field 'complete' has incomplete type
linux-2.6/arch/arm/mach-msm/dma.c: In function 'dmov_exec_cmdptr_complete_func':
linux-2.6/arch/arm/mach-msm/dma.c:108: error: implicit declaration of function 'complete'
linux-2.6/arch/arm/mach-msm/dma.c: In function 'msm_dmov_exec_cmd':
linux-2.6/arch/arm/mach-msm/dma.c:120: error: implicit declaration of function 'init_completion'
linux-2.6/arch/arm/mach-msm/dma.c:123: error: implicit declaration of function 'wait_for_completion'
and the fix is just to add the header.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Save/restore MISC_ENABLE register on suspend/resume.
This fixes OOPS (invalid opcode) on resume from STR on Asus P4P800-VM,
which wakes up with MWAIT disabled.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15385
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix potential initial_lfsr buffer overrun.
Writing past the end of the buffer could happen when index == ENTRIES
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
pcibios_fixup_device_resources() presently skips over resources flagged
with IORESOURCE_PCI_FIXED, which is a remnant of the old PCI-auto code.
The only user for this at present is the Dreamast GAPSPCI code which
can't tolerate any adjustments to the BARs, but a combination of the
IORESOURCE_PCI_FIXED and zeroed out hose offsets does the right thing for
this case already, so we simply kill off the special casing.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At the point of the test, action cannot be NULL, as it has been dereferenced
in the code just above.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Make intc messages consistent via pr_fmt.
sh: make sure static declaration on ms7724se
sh: make sure static declaration on mach-migor
sh: make sure static declaration on mach-ecovec24
sh: make sure static declaration on mach-ap325rxa
clocksource: sh_cmt: compute mult and shift before registration
clocksource: sh_tmu: compute mult and shift before registration
sh: PIO disabling for x3proto and urquell.
sh: mach-sdk7786: conditionally disable PIO support.
sh: support for platforms without PIO.
usb: r8a66597-hcd pio to mmio accessor conversion.
usb: gadget: r8a66597-udc pio to mmio accessor conversion.
usb: gadget: m66592-udc pio to mmio accessor conversion.
sh: add romImage MMCIF boot for sh7724 and Ecovec V2
sh: add boot code to MMCIF driver header
sh: prepare MMCIF driver header file
sh: allow romImage data between head.S and the zero page
sh: Add support MMCIF for ecovec
sh: remove duplicated #include
input: serio: disable i8042 for non-cayman sh platforms.
...
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core: (83 commits)
i7core_edac: Better describe the supported devices
Add support for Westmere to i7core_edac driver
i7core_edac: don't free on success
i7core_edac: Add support for X5670
Always call i7core_[ur]dimm_check_mc_ecc_err
i7core_edac: fix memory leak of i7core_dev
EDAC: add __init to i7core_xeon_pci_fixup
i7core_edac: Fix wrong device id for channel 1 devices
i7core: add support for Lynnfield alternate address
i7core_edac: Add initial support for Lynnfield
i7core_edac: do not export static functions
edac: fix i7core build
edac: i7core_edac produces undefined behaviour on 32bit
i7core_edac: Use a more generic approach for probing PCI devices
i7core_edac: PCI device is called NONCORE, instead of NOCORE
i7core_edac: Fix ringbuffer maxsize
i7core_edac: First store, then increment
i7core_edac: Better parse "any" addrmask
i7core_edac: Use a lockless ringbuffer
edac: Create an unique instance for each kobj
...
kunmap_atomic() takes a pointer to within the page, not the struct page.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, smpboot: Fix cores per node printing on boot
x86/amd-iommu: Fall back to GART if initialization fails
x86/amd-iommu: Fix crash when request_mem_region fails
x86/mm: Remove unused DBG() macro
arch/x86/kernel: Add missing spin_unlock
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/macio: Fix probing of macio devices by using the right of match table
agp/uninorth: Fix oops caused by flushing too much
powerpc/pasemi: Update MAINTAINERS file
powerpc/cell: Fix integer constant warning
powerpc/kprobes: Remove resume_execution() in kprobes
powerpc/macio: Don't dereference pointer before null check
* 'for-linus/bugfixes' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: avoid allocation causing potential swap activity on the resume path
xen: ensure timer tick is resumed even on CPU driving the resume
* 'perf-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix crash in swevents
perf buildid-list: Fix --with-hits event processing
perf scripts python: Give field dict to unhandled callback
perf hist: fix objdump output parsing
perf-record: Check correct pid when forking
perf: Do the comm inheritance per thread in event__process_task
perf: Use event__process_task from perf sched
perf: Process comm events by tid
blktrace: Fix new kernel-doc warnings
perf_events: Fix unincremented buffer base on partial copy
perf_events: Fix event scheduling issues introduced by transactional API
perf_events, trace: Fix perf_trace_destroy(), mutex went missing
perf_events, trace: Fix probe unregister race
perf_events: Fix races in group composition
perf_events: Fix races and clean up perf_event and perf_mmap_data interaction
The core suspend/resume code is run from stop_machine on CPU0 but
parts of the suspend/resume machinery (including xen_arch_resume) are
run on whichever CPU happened to schedule the xenwatch kernel thread.
As part of the non-core resume code xen_arch_resume is called in order
to restart the timer tick on non-boot processors. The boot processor
itself is taken care of by core timekeeping code.
xen_arch_resume uses smp_call_function which does not call the given
function on the current processor. This means that we can end up with
one CPU not receiving timer ticks if the xenwatch thread happened to
be scheduled on CPU > 0.
Use on_each_cpu instead of smp_call_function to ensure the timer tick
is resumed everywhere.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Stable Kernel <stable@kernel.org> # .32.x
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix smatch warning: warning: constant 0x800000000 is so big it is long
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
emulate_step() in kprobe_handler() would've already determined if the
probed instruction can be emulated. We single-step in hardware only if
the instruction couldn't be emulated. resume_execution() therefore is
superfluous -- all we need is to fix up the instruction pointer after
single-stepping.
Thanks to Paul Mackerras for catching this.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes bug introduced by commit 61c7a080a5
(of: Always use 'struct device.of_node' to get device node pointer)
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Percpu initialization happens now after booting the cores on the
machine and this causes them all to be displayed as belonging to
node 0:
Jun 8 05:57:21 kepek kernel: [ 0.106999] Booting Node 0,
Processors #1#2#3#4#5#6#7#8#9#10#11#12#13#14#15#16#17#18#19#20#21#22#23 Ok.
Use early_cpu_to_node() to get the correct node of each core
instead.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mike Travis <travis@sgi.com>
LKML-Reference: <20100601190455.GA14237@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
urquell only provides PIO in the PCI case, while the x3proto board never
had a working PCIe controller, so it can simply disable it outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This extends some of the existing special casing for HAS_IOPORT
platforms and gets it to the point where platforms can begin to
conditionally select it.
The major changes here are that the PIO routines themselves go away
completely, including all of the machvec port mapping wrappers. With this
in place it's possible for any non-machvec abusing platform to disable
PIO completely. At present this is left as an opt-in until the abusers
are the odd ones out instead of the majority.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Don't export cvt_fd & _df when CONFIG_PPC_FPU is not set
powerpc/44x: icon: select SM502 and frame buffer console support
powerpc/85xx: Add P1021MDS board support
powerpc/85xx: Change MPC8572DS camp dtses for MSI sharing
powerpc/fsl_msi: add removal path and probe failing path
powerpc/fsl_msi: enable msi sharing through AMP OSes
powerpc/fsl_msi: enable msi allocation in all banks
powerpc/fsl_msi: fix the conflict of virt_msir's chip_data
powerpc/fsl_msi: Add multiple MSI bank support
powerpc/kexec: Add support for FSL-BookE
powerpc/fsl-booke: Move the entry setup code into a seperate file
powerpc/fsl-booke: fix the case where we are not in the first page
powerpc/85xx: Enable support for ports 3 and 4 on 8548 CDS
powerpc/fsl-booke: Add hibernation support for FSL BookE processors
powerpc/e500mc: Implement machine check handler.
powerpc/44x: Add basic ICON PPC440SPe board support
powerpc/44x: Fix UART clocks on 440SPe
powerpc/44x: Add reset-type to katmai.dts
powerpc/44x: Adding PCI-E support for PowerPC 460SX based SOC.
* 'for-35' of git://repo.or.cz/linux-kbuild: (81 commits)
kbuild: Revert part of e8d400a to resolve a conflict
kbuild: Fix checking of scm-identifier variable
gconfig: add support to show hidden options that have prompts
menuconfig: add support to show hidden options which have prompts
gconfig: remove show_debug option
gconfig: remove dbg_print_ptype() and dbg_print_stype()
kconfig: fix zconfdump()
kconfig: some small fixes
add random binaries to .gitignore
kbuild: Include gen_initramfs_list.sh and the file list in the .d file
kconfig: recalc symbol value before showing search results
.gitignore: ignore *.lzo files
headerdep: perlcritic warning
scripts/Makefile.lib: Align the output of LZO
kbuild: Generate modules.builtin in make modules_install
Revert "kbuild: specify absolute paths for cscope"
kbuild: Do not unnecessarily regenerate modules.builtin
headers_install: use local file handles
headers_check: fix perl warnings
export_report: fix perl warnings
...
* 'for-linus' of git://www.jni.nu/cris:
CRIS: Don't use mask_irq as symbol name
CRIS: Simplify param.h by simply including <asm-generic/param.h>
CRISv10: Whitespace fixes for hw_settings.S
CRISv10: Trivial fixes.
CRISv32: Fix RS485 port 4 CD Kconfig item.
CRISv32: Remove duplicated Kconfig items.
cris: push down BKL into some device drivers
This patch implements a fallback to the GART IOMMU if this
is possible and the AMD IOMMU initialization failed.
Otherwise the fallback would be nommu which is very
problematic on machines with more than 4GB of memory or
swiotlb which hurts io-performance.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When request_mem_region fails the error path tries to
disable the IOMMUs. This accesses the mmio-region which was
not allocated leading to a kernel crash. This patch fixes
the issue.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The transactional API patch between the generic and model-specific
code introduced several important bugs with event scheduling, at
least on X86. If you had pinned events, e.g., watchdog, and were
over-committing the PMU, you would get bogus counts. The bug was
showing up on Intel CPU because events would move around more
often that on AMD. But the problem also existed on AMD, though
harder to expose.
The issues were:
- group_sched_in() was missing a cancel_txn() in the error path
- cpuc->n_added was not properly maintained, leading to missing
actions in hw_perf_enable(), i.e., n_running being 0. You cannot
update n_added until you know the transaction has succeeded. In
case of failed transaction n_added was not adjusted back.
- in case of failed transactions, event_sched_out() was called
and eventually invoked x86_disable_event() to touch the HW reg.
But with transactions, on X86, event_sched_in() does not touch
HW registers, it simply collects events into a list. Thus, you
could end up calling x86_disable_event() on a counter which
did not correspond to the current event when idx != -1.
The patch modifies the generic and X86 code to avoid all those problems.
First, we keep track of the number of events added last. In case the
transaction fails, we substract them from n_added. This approach is
necessary (as opposed to delaying updates to n_added) because not all
event updates use the transaction API, e.g., single events.
Second, we encapsulate the event_sched_in() and event_sched_out() in
group_sched_in() inside the transaction. That makes the operations
symmetrical and you can also detect that you are inside a transaction
and skip the HW reg access by checking cpuc->group_flag.
With this patch, you can now overcommit the PMU even with pinned
system-wide events present and still get valid counts.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1274796225.5882.1389.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch is V2 of the MMCIF romImage boot support
for sh7724 and the Ecovec board. With this patch
applied and CONFIG_ROMIMAGE_MMCIF selected the
romImage kernel image can be written to a MMC card
and booted directly by the sh7724 cpu.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the romImage code to allow putting data between
the head.S file and the empty_zero_page. Needed in the
case of more advanced loader code in a separate C file.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MMCIF platform data for the Ecovec board.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch registers the WM8750 codec on a proper place on the SPITZ machine
after the WM8750 driver was converted to new API.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This partially reverts commit 4ec37de89d
("[IA64] Fix build breakage"), since the commit that made it necessary
got reverted earlier (see commit 35926ff5fb, 'Revert "cpusets:
randomize node rotor used in cpuset_mem_spread_node()"')
Even if we ever re-introduce this, there is no reason to make
__node_random be some architecture-specific function.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (47 commits)
mfd: Rename twl5031 sih modules
mfd: Storage class for timberdale should be before const qualifier
mfd: Remove unneeded and dangerous clearing of clientdata
mfd: New AB8500 driver
gpio: Fix inverted rdc321x gpio data out registers
mfd: Change rdc321x resources flags to IORESOURCE_IO
mfd: Move pcf50633 irq related functions to its own file.
mfd: Use threaded irq for pcf50633
mfd: pcf50633-adc: Fix potential race in pcf50633_adc_sync_read
mfd: Fix pcf50633 bitfield logic in interrupt handler
gpio: rdc321x needs to select MFD_CORE
mfd: Use menuconfig for quicker config editing
ARM: AB3550 board configuration and irq for U300
mfd: AB3550 core driver
mfd: AB3100 register access change to abx500 API
mfd: Renamed ab3100.h to abx500.h
gpio: Add TC35892 GPIO driver
mfd: Add Toshiba's TC35892 MFD core
mfd: Delay to mask tsc irq in max8925
mfd: Remove incorrect wm8350 kfree
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cpufeature: Unbreak compile with gcc 3.x
x86, pat: Fix memory leak in free_memtype
x86, k8: Fix section mismatch for powernowk8_exit()
lib/atomic64_test: fix missing include of linux/kernel.h
x86: remove last traces of quicklist usage
x86, setup: Phoenix BIOS fixup is needed on Dell Inspiron Mini 1012
x86: "nosmp" command line option should force the system into UP mode
arch/x86/pci: use kasprintf
x86, apic: ack all pending irqs when crashed/on kexec
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: Call pagefault_disable/pagefault_enable in kmap_atomic/kunmap_atomic
parisc: Remove unnecessary macros from entry.S
parisc: LWS fixes for syscall.S
parisc: Delete unnecessary nop's in entry.S
parisc: Avoid interruption in critical region in entry.S
parisc: invoke oom-killer from page fault
parisc: clear floating point exception flag on SIGFPE signal
parisc: Use of align_frame provides stack frame.
This reverts commit 0ac0c0d0f8, which
caused cross-architecture build problems for all the wrong reasons.
IA64 already added its own version of __node_random(), but the fact is,
there is nothing architectural about the function, and the original
commit was just badly done. Revert it, since no fix is forthcoming.
Requested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on the generic implementation of kmap_atomic and kunmap_atomic,
we should call pagefault_disable and pagefault_enable in our PA8000
implementation.
The define for kmap_atomic_prot was also missing, and I updated
kmap_atomic_pfn to use the generic implementation because of the
change to kmap_atomic.
I believe that this change is needed to fix the fork copy-on-write
bug.
Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The EXTR, DEP and DEPI macros are unnecessary. There are PA 1.X
pneumonics available with the same functionality, and the DEP and DEPI
macros conflict with assembler pneumonics.
Tested on a variety of 32 and 64-bit systems.
Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
1) Gate immediately and save a branch.
2) Fix off by one error in checking entry number.
3) Use sr7 instead of sr3 in error return path as sr3 might not
contain correct value.
4) Enable locking on UP systems to prevent incorrect operation of
the cas_action critical region on page faults.
Tested on several systems, including UP c3750 with 2.6.33.2 kernel.
Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
As explained in commit 1c0fe6e3bd, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.
Cc: linux-parisc@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Clear the floating point exception flag before returning to
user space. This is needed, else the libc trampoline handler
may hit the same SIGFPE again while building up a trampoline
to a signal handler.
Fixes debian bug #559406.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Any assembly constant generated with the use of
align_frame includes size for a full stack frame.
Signed-off-by: Carlos O'Donell <carlos@systemhalted.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
intel_idle: native hardware cpuidle driver for latest Intel processors
ACPI: acpi_idle: touch TS_POLLING only in the non-MWAIT case
acpi_pad: uses MONITOR/MWAIT, so it doesn't need to clear TS_POLLING
sched: clarify commment for TS_POLLING
ACPI: allow a native cpuidle driver to displace ACPI
cpuidle: make cpuidle_curr_driver static
cpuidle: add cpuidle_unregister_driver() error check
cpuidle: fail to register if !CONFIG_CPU_IDLE
Commit 38516ab59f ("tracing: Let
tracepoints have data passed to tracepoint callbacks") requires this
fixup to the powerpc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARCH_KMALLOC_MINALIGN was already defined in asm/mem-layout.h and so shouldn't
have been added to asm/cache.h as well, but rather altered in place.
The commit that added it to asm/cache.h was:
commit 69dcf3db03
Author: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Date: Mon May 24 14:32:54 2010 -0700
frv: set ARCH_KMALLOC_MINALIGN
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is
DMA-safe: the buffer doesn't share a cache with the others.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the framebuffer driver and some basic LCD configurations
that should be suitable for the SMDK boards.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The SPI driver was added last kernel round, so enable
the core SPI and add the 64XX and bitbang driver as
modules.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_xusbxti clock is added to the list of clocks to be
registred during boot time clock registration.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: edited title]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the USB OTG HCLK clock to the list of clocks to be registered
during initialization.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the documentation on the gpio configuration calls to add more
references to useful information and also to document the values that
are passed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We don't name our generic fsync implementations very well currently.
The no-op implementation for in-memory filesystems currently is called
simple_sync_file which doesn't make too much sense to start with,
the the generic one for simple filesystems is called simple_fsync
which can lead to some confusion.
This patch renames the generic file fsync method to generic_file_fsync
to match the other generic_file_* routines it is supposed to be used
with, and the no-op implementation to noop_fsync to make it obvious
what to expect. In addition add some documentation for both methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
TS_POLLING set tells the scheduler an idle_task will poll
need_resched() to look for work.
TS_POLLING clear tells resched_task() and wake_up_idle_cpu()
that the remote CPU's idle_task is now sleeping in idle,
and thus requires a reschedule interrupt notice work.
Update the description of TS_POLLING to reflect how it works.
"idle task polling need_resched, skip sending interrupt"
Wordsmithing-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Add a new driver to support the AB8500 Power Management chip, replacing
the current AB4500. The new driver replaces the old one, instead of an
incremental modification, because this is a substantial overhaul
including:
- Split of the driver into -core and -spi portions, to allow another
interface layer to be added
- Addition of interrupt support
- Switch to MFD core API for handling subdevices
- Simplification of the APIs to remove a redundant block parameter
- Rename of the APIs and macros from ab4500_* to ab8500_*
- Rename of the files from ab4500* to ab8500*
- Change of the driver name from ab4500 to ab8500
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the i2c board configuration needed for the
Mixed Signal chip AB3550. It also adds the irq numbers needed
for the irq_chip implementation.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The goal here is to make way for a more general interface for the
analog baseband chips ab3100 ab3550 ab550 and future chips.
This patch have been divided into two parts since both changing name
and content of a file is not recommended in git.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The touch screen controller in the TPS6507x chip needs values that are
dependent on the characteristics of the touch screen hardware being used
in the board design. In addition, the board provides version information
that is exposed via the kernel input sub-system.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This file is replaced by a cleaner version with the adding of a MFD driver for
the southbridge.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In commit 0ac0c0d0f8
cpusets: randomize node rotor used in cpuset_mem_spread_node()
Jack Steiner fixed a problem with too many small tasks being
assigned to node 0. Copy his code to ia64 to avoid build error.
arch/ia64/kernel/smpboot.c:641: error: ‘cpu_to_node_map’ undeclared (first use in this function)
In commit 3bccd99627
numa: ia64: use generic percpu var numa_node_id() implementation
Lee Schermerhorn added some set_numa_node() calls - but these
only work on CONFIG_NUMA=y configurations. Surround the calls
with #ifdef CONFIG_NUMA
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (61 commits)
tracing: Add __used annotation to event variable
perf, trace: Fix !x86 build bug
perf report: Support multiple events on the TUI
perf annotate: Fix up usage of the build id cache
x86/mmiotrace: Remove redundant instruction prefix checks
perf annotate: Add TUI interface
perf tui: Remove annotate from popup menu after failure
perf report: Don't start the TUI if -D is used
perf: Fix getline undeclared
perf: Optimize perf_tp_event_match()
perf: Remove more code from the fastpath
perf: Optimize the !vmalloc backed buffer
perf: Optimize perf_output_copy()
perf: Fix wakeup storm for RO mmap()s
perf-record: Share per-cpu buffers
perf-record: Remove -M
perf: Ensure that IOC_OUTPUT isn't used to create multi-writer buffers
perf, trace: Optimize tracepoints by using per-tracepoint-per-cpu hlist to track events
perf, trace: Optimize tracepoints by removing IRQ-disable from perf/tracepoint interaction
perf tui: Allow disabling the TUI on a per command basis in ~/.perfconfig
...
This completes the DMA40 support with the platform-specific
configuration for U8500/DB8500.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson_nomadik_linux@list.st.com
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
[fixed up dma40_{tx|rx}_map declaration/initialization]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
gcc 3 is too braindamaged to be able to compile static_cpu_has() --
apparently it can't tell that a constant passed to an inline function
is still a constant -- so if we're using gcc 3, just use the dynamic
test. This is bad for performance, but if you care about performance,
don't use an ancient, known-to-optimize-poorly compiler.
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
LKML-Reference: <4BF2FF82.7090005@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add mx31moboard MC13783 led support
leds: Add mc13783 LED support
leds: leds-ss4200: fix led_classdev_unregister twice in error handling
leds: leds-lp3944: properly handle lp3944_configure fail in lp3944_probe
leds: led-class: set permissions on max_brightness file to 0444
leds: leds-gpio: Change blink_set callback to be able to turn off blinking
leds: Add LED driver for the Soekris net5501 board
leds: 88pm860x - fix checking in probe function
x86 arch specific changes to use generic numa_node_id() based on generic
percpu variable infrastructure. Back out x86's custom version of
numa_node_id()
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rework the generic version of the numa_node_id() function to use the new
generic percpu variable infrastructure.
Guard the new implementation with a new config option:
CONFIG_USE_PERCPU_NUMA_NODE_ID.
Archs which support this new implemention will default this option to 'y'
when NUMA is configured. This config option could be removed if/when all
archs switch over to the generic percpu implementation of numa_node_id().
Arch support involves:
1) converting any existing per cpu variable implementations to use
this implementation. x86_64 is an instance of such an arch.
2) archs that don't use a per cpu variable for numa_node_id() will
need to initialize the new per cpu variable "numa_node" as cpus
are brought on-line. ia64 is an example.
3) Defining USE_PERCPU_NUMA_NODE_ID in arch dependent Kconfig--e.g.,
when NUMA is configured. This is required because I have
retained the old implementation by default to allow archs to
be modified incrementally, as desired.
Subsequent patches will convert x86_64 and ia64 to use this implemenation.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
parisc uses iova and iova_length in scatterlist structure instead of
dma_address and dma_length. However, the accessor are used so we can
convert parisc to use asm-generic/scatterlist.h easily.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are more architectures that don't support ARCH_HAS_SG_CHAIN than
those that support it. This removes removes ARCH_HAS_SG_CHAIN in
asm-generic/scatterlist.h and lets arhictectures to define it.
It's clearer than defining ARCH_HAS_SG_CHAIN asm-generic/scatterlist.h and
undefing it in arhictectures that don't support it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are only two ways to define sg_dma_len(); use sg->dma_length or
sg->length. This patch introduces NEED_SG_DMA_LENGTH that enables
architectures to choose sg->dma_length or sg->length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the first half of the attempt to use asm-generic/scatterlist.h
on every architecture.
There are only two ways to define scatterlist structure. So it's easy
to convert every architecture to use asm-generic/scatterlist.h.
This patch:
The trick for ISA_DMA_THRESHOLD in asm-generic/scatterlist.h doesn't work
for powerpc. This lets architectures defin ISA_DMA_THRESHOLD.
Hopefully, we can remove ISA_DMA_THRESHOLD in the future; we can do better
to decide if the bouncing is necessary or not.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sync_single_range_for_cpu and sync_single_range_for_device hooks in
swiotlb_dma_ops are unnecessary because sync_single_for_cpu and
sync_single_for_device are used there.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Becky Bruce <beckyb@kernel.crashing.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sync_single_range_for_cpu and sync_single_range_for_device hooks in
swiotlb_dma_ops are unnecessary because sync_single_for_cpu and
sync_single_for_device are used there.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sync_single_range_for_cpu and sync_single_range_for_device hooks in
swiotlb_dma_ops are unnecessary because sync_single_for_cpu and
sync_single_for_device are used there.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the maintenance access functions to farend RapidIO devices.
1. Fixed shift of the given offset, to open the maintenance window
2. Mask offset to limit access to the opened maintenance window
3. Added extended destid part to rowtear register, required for 16bit mode
This method is matching maintenance transactions generation described
by Freescale in the appnote AN2932. With this modification full access
to a 16MB maintenance window is possible, this patch is required for
IDT cps switches. For easier handling of the access routines, the
access was limited to aligned memory regions. This should be no problem
because all registers are 32bit wide.
Signed-off-by: Thomas Moll <thomas.moll@sysgo.com>
Tested-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Machine Check exception handling into RapidIO port driver for
Freescale SoCs (MPC85xx).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Tested-by: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add RapidIO Port-Write message handler for Freescale SoCs with RapidIO
port.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Tested-by: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add RapidIO Port-Write message handling in the context of Error
Management Extensions Specification Rev.1.3.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Tested-by: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By the previous modification, the cpu notifier can return encapsulate
errno value. This converts the cpu notifiers for s390.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By the previous modification, the cpu notifier can return encapsulate
errno value. This converts the cpu notifiers for msr, cpuid, and
therm_throt.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Preparation to make task->signal immutable, no functional changes.
It doesn't matter which pointer we check under tasklist to ensure the task
was not released, ->signal or ->sighand. But we are going to make
->signal refcountable, change the code to use ->sighand.
Note: this code doesn't need this check and tasklist_lock at all, it
should be converted to use lock_task_sighand(). And, the code under
SIGNAL_STOP_STOPPED check looks wrong.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin/FRV/SuperH guys all have the same exact FDPIC ptrace code in
their arch handlers (since they were probably copied & pasted). Since
these ptrace interfaces are an arch independent aspect of the FDPIC code,
unify them in the common ptrace code so new FDPIC ports don't need to copy
and paste this fundamental stuff yet again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some workloads that create a large number of small files tend to assign
too many pages to node 0 (multi-node systems). Part of the reason is that
the rotor (in cpuset_mem_spread_node()) used to assign nodes starts at
node 0 for newly created tasks.
This patch changes the rotor to be initialized to a random node number of
the cpuset.
[akpm@linux-foundation.org: fix layout]
[Lee.Schermerhorn@hp.com: Define stub numa_random() for !NUMA configuration]
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Paul Menage <menage@google.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody uses that anymore, so remove and expect drivers to use the gpiolib
implementation.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stop using the omap-specific implementations for gpio debouncing now that
gpiolib provides its own support.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP supports debouncing of gpio lines, implement the method using
gpiolib.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some platforms like DM355, the number of EDMA parameter slots available
for EDMA_SLOT_ANY usage are few. In such cases, if MMC/SD uses 16 slots
for each instance of MMC controller, then the number of slots available
for other modules will be very few.
By passing the number of EDMA slots to be used in MMC driver from platform
data, EDMA slots available for other purposes can be controlled.
Most of the platforms will not use this platform data variable. But on
DM355, as the number of EDMA resources available is limited, the number of
scatter- gather segments used inside the MMC driver can be 8 (passed as
platform data) instead of 16. On DM355, when the number of scatter-gather
segments was reduced to 8, I saw a performance difference of about
0.25-0.4 Mbytes/sec during write. Read performance variations were
negligible.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a spin_unlock missing on the error path. The locks and unlocks are
balanced in other functions, so it seems that the same should be the case
here.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* spin_lock(E1,...);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* spin_unlock(E1,...);
// </smpl>
Cc: stable@kernel.org
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch reorganises the sa1111_resume() function in a manner the spinlock
happens after calling the sa1111_wake(). This fixes two bugs:
1) This function called sa1111_wake() which tried to claim the same spinlock
the sa1111_resume() already claimed. This would result in certain deadlock.
Original idea for this part: Russell King <rmk+kernel@arm.linux.org.uk>
2) The function didn't unlock the spinlock in case the chip didn't report
correct ID.
Original idea for this part: Julia Lawall <julia@diku.dk>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adjusts the clockrate for the MTU timer. On the different
UX500 variants this rate is different. The platform can also have
been set up at hardware initialization, bootloader or early init
for different clock speeds. To have the clock framework available
early so the timers can use them, the clock initialization for
Nomadik and ux500 is moved to IRQ init time. A custom per-clock
callback is added to handle special cases like this.
This solves a user-visible bug: without this patch the current
UX500 platforms will not be synchronized to wall-clock time and
the platform will drift in time.
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a bug in mm/init.c when freeing the TCM compile memory,
this was being referred to as a char * which is incorrect: this
will dereference the pointer and feed in the value at the location
instead of the address to it. Change it to a plain char and use
&(char) to reference it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
vfp_put_double() takes the double value in r0,r1 not r1,r2.
Reported-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move from SLUB to SLAB, as this is what the world plans to align
to, every distribution enables, and thus is what everyone actually
is testing.
Signed-off-by: David S. Miller <davem@davemloft.net>
All distros have this option switched on, so lets get rid of at least
one of the tons of config options that are available.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove superfluous EXPORT_SYMBOLS and do coding style cleanup while
being at it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Send unit checks that occur during internal I/O to the device driver
and react according to its return code.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This config option enables or disables three single instructions
which aren't expensive. This is too fine grained.
Besided that everybody who uses kvm would enable it anyway in order
to debug performance problems.
Just remove it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The probed instructions will be executed in a single stepped and irq
disabled context. Therefore the results of stnsm, stosm and epsw would
be wrong if probed.
So let's just disallow probing of these functions. If really needed a
fixup could be written for each of them, but I doubt it's worth it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There might be a scheduled cmm_timer if the cmm module gets unloaded.
That timer was not deleted during module unload and thus could lead
to system crash later on.
Besides that reorder function calls in module init and exit code to
avoid a couple of other races which could lead to accesses to
uninitialized data.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reserve_memtype will allocate memory for new memtype, but
in free_memtype, after the memtype erased from rbtree, the
memory is not freed.
Changes since V1:
make rbt_memtype_erase return erased memtype so that
it can be freed in free_memtype.
[ hpa: not for -stable: 2.6.34 and earlier not affected ]
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
LKML-Reference: <1274838670-8731-1-git-send-email-dfeng@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Jack Steiner <steiner@sgi.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Use the pcf50633 backlight driver instead of the platform backlight driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This reverts commit b3b77c8cae, which was
also totally broken (see commit 0d2daf5cc8 that reverted the crc32
version of it). As reported by Stephen Rothwell, it causes problems on
big-endian machines:
> In file included from fs/jfs/jfs_types.h:33,
> from fs/jfs/jfs_incore.h:26,
> from fs/jfs/file.c:22:
> fs/jfs/endian24.h:36:101: warning: "__LITTLE_ENDIAN" is not defined
The kernel has never had that crazy "__BYTE_ORDER == __LITTLE_ENDIAN"
model. It's not how we do things, and it isn't how we _should_ do
things. So don't go there.
Requested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two RGB led on mx31moboard using MC13783 led subsystem
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The leds-gpio blink_set() callback follows the same prototype as the
main leds subsystem blink_set() one.
The problem is that to stop blink, normally, a leds driver does it
in the brightness_set() callback when asked to set a new fixed value.
However, with leds-gpio, the platform has no hook to do so, as this
later callback results in a standard GPIO manipulation.
This changes the leds-gpio specific callback to take a new argument
that indicates whether the LED should be blinking or not and in what
state it should be set if not. We also update the dns323 platform
which seems to be the only user of this so far.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The commit 45c79433c0 got things building
but then commit 17d2f877ae8b68b09bf88a9949ee64fbbda5ee10 and others
where merged in from a seperate tree and this has resulted from a build
failure due to the redefinition of IRQ_EINT().
Fix this by merging a new commit.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch does the following:
1. Corrects the common platform code for external interrupts for using the
VIC mask/unmask bits also.
2. Moves the common defines related to external interrupt for plat-s5p
to common files.
3. Based on the new common defines, corresponding changes are made in the
affected platforms (S5P6440, S5P6442 and S5PC100).
Signed-off-by: Pannaga Bhushan <p.bhushan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For some reason, the pte_none() calculation for srmmu sparc32
chips was masking out the top 4 bits. That doesn't make any
sense, as those are just some of the physical bits of the PTE
encoding.
Furthermore, this mistake breaks things when the offset of of a swap
entry has a large enough offset as reported by Тхай Кирилл.
Sun4c always set it to zero, so it's really completely useless,
kill it.
Reported-by: Тхай Кирилл <tkhai@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'alpha-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: simplify and optimize sched_find_first_bit
alpha: invoke oom-killer from page fault
Convert alpha to use clocksources instead of arch_gettimeoffset
Fix the following warning:
"WARNING: arch/x86/kernel/built-in.o(.exit.text+0x72):
Section mismatch in reference from the function powernowk8_exit() to the variable .cpuinit.data:cpb_nb
The function __exit powernowk8_exit() references a variable
__cpuinitdata cpb_nb. This is often seen when error handling in the exit
function uses functionality in the init path. The fix is often to remove
the __cpuinitdata annotation of cpb_nb so it may be used outside an init
section."
Cc: <stable@kernel.org>
Reported-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100525152858.GA24836@aftab>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Search only the first 100 bits instead of 140, saving a couple
instructions. The resulting code is about 1/3 faster (40K ticks/1000
iterations down to 30K ticks/1000 iterations).
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Matt Turner <mattst88@gmail.com>
As explained in commit 1c0fe6e3bd, we want to call the architecture
independent oom killer when getting an unexplained OOM from
handle_mm_fault, rather than simply killing current.
[mattst88: kill now unused 'survive' label]
Cc: linux-alpha@vger.kernel.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: linux-arch@vger.kernel.org
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Alpha has a tsc like rpcc counter that it uses to manage time.
This can be converted to an actual clocksource instead of utilizing
the arch_gettimeoffset method that is really only there for legacy
systems with no continuous counter.
Further cleanups could be made if alpha converted to the clockevent
model.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Richard Henderson <rth@twiddle.net>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Tested-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
This adds:
alias: devname:<name>
to some common kernel modules, which will allow the on-demand loading
of the kernel module when the device node is accessed.
Ideally all these modules would be compiled-in, but distros seems too
much in love with their modularization that we need to cover the common
cases with this new facility. It will allow us to remove a bunch of pretty
useless init scripts and modprobes from init scripts.
The static device node aliases will be carried in the module itself. The
program depmod will extract this information to a file in the module directory:
$ cat /lib/modules/2.6.34-00650-g537b60d-dirty/modules.devname
# Device nodes to trigger on-demand module loading.
microcode cpu/microcode c10:184
fuse fuse c10:229
ppp_generic ppp c108:0
tun net/tun c10:200
dm_mod mapper/control c10:235
Udev will pick up the depmod created file on startup and create all the
static device nodes which the kernel modules specify, so that these modules
get automatically loaded when the device node is accessed:
$ /sbin/udevd --debug
...
static_dev_create_from_modules: mknod '/dev/cpu/microcode' c10:184
static_dev_create_from_modules: mknod '/dev/fuse' c10:229
static_dev_create_from_modules: mknod '/dev/ppp' c108:0
static_dev_create_from_modules: mknod '/dev/net/tun' c10:200
static_dev_create_from_modules: mknod '/dev/mapper/control' c10:235
udev_rules_apply_static_dev_perms: chmod '/dev/net/tun' 0666
udev_rules_apply_static_dev_perms: chmod '/dev/fuse' 0666
A few device nodes are switched to statically allocated numbers, to allow
the static nodes to work. This might also useful for systems which still run
a plain static /dev, which is completely unsafe to use with any dynamic minor
numbers.
Note:
The devname aliases must be limited to the *common* and *single*instance*
device nodes, like the misc devices, and never be used for conceptually limited
systems like the loop devices, which should rather get fixed properly and get a
control node for losetup to talk to, instead of creating a random number of
device nodes in advance, regardless if they are ever used.
This facility is to hide the mess distros are creating with too modualized
kernels, and just to hide that these modules are not compiled-in, and not to
paper-over broken concepts. Thanks! :)
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Ian Kent <raven@themaw.net>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/xilinx: Fix compile error
spi/davinci: Fix clock prescale factor computation
spi: move bitbang txrx utility functions to private header
spi/mpc5121: Add SPI master driver for MPC5121 PSC
powerpc/mpc5121: move PSC FIFO memory init to platform code
spi/ep93xx: implemented driver for Cirrus EP93xx SPI controller
Documentation/spi/* compile warning fix
spi/omap2_mcspi: Check params before dereference or use
spi/omap2_mcspi: add turbo mode support
spi/omap2_mcspi: change default DMA_MIN_BYTES value to 160
spi/pl022: fix stop queue procedure
spi/pl022: add support for the PL023 derivate
spi/pl022: fix up differences between ARM and ST versions
spi/spi_mpc8xxx: Do not use map_tx_dma to unmap rx_dma
spi/spi_mpc8xxx: Fix QE mode Litte Endian
spi/spi_mpc8xxx: fix potential memory corruption.
Dmitry Baryshkov