- added MIPS support for brcmstb PCIe controller
- added Loongson 2K1000 reset driver
- removed board support for rbtx4938/rbtx4939
- removed support for TX4939 SoCs
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQJOBAABCAA4FiEEbt46xwy6kEcDOXoUeZbBVTGwZHAFAmHhNi8aHHRzYm9nZW5k
QGFscGhhLmZyYW5rZW4uZGUACgkQeZbBVTGwZHDjGBAAogFGgNYUSzLUHQfGdBcx
fk/Lo+psvZ03cz5i9L4+7D0N3/K55/GXhSvDIHMhbYX41qklCy/ie+hxp3rwbjD3
RTLV3D4YdoJkcn+lPcKgtvGxKXjLE0A2ho/TmrAce2mvrei3BWu7dDmJC0WFjmt7
SZeg3ALjEdYVObO3vaN3pBMuuUuNvYS8DlLadzGwx1rDPHxGOZBri025bl9g6I+m
rQHSTa3p5DY4VsqEOXy1fUZchys1pZC6D7Ja4FPracnxYF0F4jLoWVhN+xt4QpcW
Q6o4+ykIDuL6kEKOwfTB094CeumIZSpcEwIKRYorIHeApG/XdgVBxJfcsaxBxI7V
4KYBkxG93AWwsp9CtxGEfOADoX3XnRbMZk58d6pVW7KUPXNin73jghxkc4vmaK1R
9lDyiq8RC8sh+HA5jkksCmf4otXstVlZGxNMKG3/qJy62pqEuFOIoB1Q8hN15c7w
HlFM7ZFf/6ZWVWm3dSKdB+hZNWTBVL2ucH9bf4s6f408Mj2sMMRIuFUKH/zJzVZZ
SeXy+tv5BcWbU+1EdaHzQJWM69iBCxasNyhPJkk3Hq+vqZdjkdPruzD3pVxdm169
E6cBUSWjwrJTt8EsBWKb1+hzjZk56Brff+9AlhbLWSChto/4SJmT/wZWGvTC2hqS
GBIIDNnd2G5k5xhuVs6qQIM=
=wsIG
-----END PGP SIGNATURE-----
Merge tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for more BCM47XX based devices
- add MIPS support for brcmstb PCIe controller
- add Loongson 2K1000 reset driver
- remove board support for rbtx4938/rbtx4939
- remove support for TX4939 SoCs
- fixes and cleanups
* tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (59 commits)
MIPS: ath79: drop _machine_restart again
PCI: brcmstb: Augment driver for MIPs SOCs
MIPS: bmips: Remove obsolete DMA mapping support
MIPS: bmips: Add support PCIe controller device nodes
dt-bindings: PCI: Add compatible string for Brcmstb 74[23]5 MIPs SOCs
MIPS: compressed: Fix build with ZSTD compression
MIPS: BCM47XX: Add support for Netgear WN2500RP v1 & v2
MIPS: BCM47XX: Add support for Netgear R6300 v1
MIPS: BCM47XX: Add LEDs and buttons for Asus RTN-10U
MIPS: BCM47XX: Add board entry for Linksys WRT320N v1
MIPS: BCM47XX: Define Linksys WRT310N V2 buttons
MIPS: Remove duplicated include in local.h
MIPS: retire "asm/llsc.h"
MIPS: rework local_t operation on MIPS64
MIPS: fix local_{add,sub}_return on MIPS64
mips/pci: remove redundant ret variable
MIPS: Loongson64: Add missing of_node_put() in ls2k_reset_init()
MIPS: new Kconfig option ZBOOT_LOAD_ADDRESS
MIPS: enable both vmlinux.gz.itb and vmlinuz for generic
MIPS: signal: Return immediately if call fails
...
It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
* ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
* ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
* HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
* Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1.
-----BEGIN PGP SIGNATURE-----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=csTR
-----END PGP SIGNATURE-----
Merge tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
JFFS2:
- Fix for a deadlock in jffs2_write_begin()
UBI:
- Fixes in comments
UBIFS:
- Expose error counters in sysfs
- Many bugfixes found by Hulk Robot and others
-----BEGIN PGP SIGNATURE-----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=rpfR
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fix for a deadlock in jffs2_write_begin()
UBI:
- Fixes in comments
UBIFS:
- Expose error counters in sysfs
- Many bugfixes found by Hulk Robot and others"
* tag 'for-linus-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: GC deadlock reading a page that is used in jffs2_write_begin()
ubifs: read-only if LEB may always be taken in ubifs_garbage_collect
ubifs: fix double return leb in ubifs_garbage_collect
ubifs: fix slab-out-of-bounds in ubifs_change_lp
ubifs: fix snprintf() length check
ubifs: Document sysfs nodes
ubifs: Export filesystem error counters
ubifs: Error path in ubifs_remount_rw() seems to wrongly free write buffers
ubifs: Make use of the helper macro kthread_run()
ubi: Fix a mistake in comment
ubifs: Fix spelling mistakes
* mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
* gen_probe: Use bitmap_zalloc() when applicable
* Introduce an expert mode for forensics and debugging purposes
* Clear out unregistered devices a bit more
* Provide unique name for nvmem device
* Remove unused header file <linux/mtd/latch-addr-flash.h>
* Fixed breaking list in __mtd_del_partition.
MTD device changes:
* sst25l, mchp48l640, mchp23k256, dataflash:
- Warn about failure to unregister mtd device
Raw NAND core changes:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
* Add Pratyush as SPI NOR co-maintainer.
* Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
* Rework the flash_info flags and clarify where one should be used.
* Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
* Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
* Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
* Fix mtd size for s3an flashes.
* Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
Hyperbus changes:
* Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO+g8ACgkQJWrqGEe9
VoRW1AgAjFC58ARNBw7asYerGyiUWv7b8RjPIRWZqmcSQ6D5m20cGNBTa15c2NrC
v0dNMf2+3FrCECso6wKPbkEbLt9lHjlMmt+AdlraV0QvHBXrJq/Tc2p2ATI5kTqq
WaP4oCx1mccgO+IrEIiGikOcFx/TLBBJEk+U0Anbm16eia9Cjw+uD/q7X2HbF5xQ
MOFZyQ+rAVqkM8tCh6VHhCpX85pn9pj2ZdouOhPWsqjULaGqDbUopC70YPZLVJyx
9u4xHFaVLVae6AS5Gitser2ie8klypTN/H+1weSao43GGmwIrT0wK0mCOVIm90Zd
4frlpnt4QE/IIAKgAm+HxkWg+KV9qg==
=E8lV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
- gen_probe: Use bitmap_zalloc() when applicable
- Introduce an expert mode for forensics and debugging purposes
- Clear out unregistered devices a bit more
- Provide unique name for nvmem device
- Remove unused header file <linux/mtd/latch-addr-flash.h>
- Fixed breaking list in __mtd_del_partition.
MTD device changes:
- Warn about failure to unregister mtd device in sst25l, mchp48l640,
mchp23k256, and dataflash drivers.
Raw NAND core changes:
- Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
- OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
- Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
- Onenand:
- Remove redundant variable ooblen
- MPC5121:
- Remove unused variable in ads5121_select_chip()
- GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
- Ingenic:
- JZ4740 needs 'oob_first' read page function
- Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where
possible. Flash parameters and settings that are SFDP discoverable
should not be duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP
standard, or the SFDP tables which define those flash parameters
are not defined by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long
transactions are not allowed in 8D-8D-8D mode.
Hyperbus changes:
- Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe"
* tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (71 commits)
mtd: spi-nor: Remove debugfs entries that duplicate sysfs entries
mtd: spi-nor: micron-st: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: spansion: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: core: use 2 data bytes for template ops
mtd: spi-nor: Constify part specific fixup hooks
mtd: spi-nor: core: Remove reference to spi-nor.c
mtd: rawnand: gpmi: Use platform_get_irq_byname() to get the interrupt
mtd: rawnand: omap_elm: Use platform_get_irq() to get the interrupt
mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3
memory: omap-gpmc: Use a compatible match table when checking for NAND controller
memory: omap-gpmc: Add support for GPMC on AM64 SoC
dt-bindings: memory-controllers: ti,gpmc: Add compatible for AM64
memory: omap-gpmc: Use platform_get_irq() to get the interrupt
MAINTAINERS: Add an entry for Renesas NAND controller
mtd: rawnand: renesas: Add new NAND controller driver
dt-bindings: mtd: renesas: Describe Renesas R-Car Gen3 & RZ/N1 NAND controller
mtd: rawnand: gpmi: remove unneeded variable
mtd: rawnand: omap2: drop unused variable
mtd: rawnand: omap2: fix force_8bit flag behaviour for DMA mode
mtd: rawnand: omap2: Add compatible for AM64 SoC
...
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----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=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
After removal of RBTX4939 board support remove code for the TX4939 SoC.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
No active MIPS user own this board, so let's remove it.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO9D0ACgkQJWrqGEe9
VoRglwf/SsGcY+7vlBM1VSbUMIF/j5/xuigHIW6AxiN/hu672GMVi7nP7aHg4t3m
DpO5X6ngYFHyW79uksRfwSun/JF1mOqF4De9zhs+cy8hlV12tgEmUNB3cbv4kuFQ
e/N8/mlNrNJ2oQ1C3G3HWe3sngh2vrkhuG49t7M2TJaGAo7V4RW3z9+glNpWMb7m
YIj6gXPjPx7vuEWv80GBUcWNKBzNdRVkrQnj3C2I/ZCslnwYWBLBQxX/U9/KDkPH
7i7MgeknAlV0G/W4TfnNSAKiWOcmWdbmuJ/lOWv4+skdXoMb0/rlC6kvJqOLvbF6
2nUrc9yFTwkNfVTGJm5eWJ0yDUHMgA==
=DQck
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.17' into mtd/next
Raw NAND core:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer drivers changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmHMJxcACgkQS1VPR6WN
FOk1Ywf9GrDTrGx8Brg08qC7m2ExIiyRBFnUL4yeD9/d8p0vqqGryXeyjbaVutHR
fKf/SFrrP+gmcJS7wx4EttafgV8MPMiV1ICu/vyq2JsOlKekSEk38BXpfNOXzsgQ
UPE92AW8+BTgoL5XohnHqHrFqs+FEHAa3jCEpntWoShznZMhZ6IDwZbVlrHJC5Ts
C0S0S45X5aFgOXdNC4B0UrxAu0OryxL+vjjzG3Jl1g8GbrC/vkbR5vkMXaVgZiie
RpZtsbkcYm9vhUxOgMY+rRi4mwiTxy5Z2/Vg4Jr8nQOurO/aIvC9IZVIS4zbFOTk
08WtqtexR5S/+GCGIijJ+0BlS58hgg==
=tiIB
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.17' into mtd/next
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer drivers changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Hyperbus changes:
Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAmHFzxgQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW462AB/93JmhhKIPM6F0gwlm5fCUT6Q0HRUeXeGRS
42z21CbxG7dlf8/VUbNpNJjrMv1wYBVUlyIDZejIdLmXQVK3cdrbHv5lls96uDq6
0tmCemctHfUjbMfINy7cwTMmOkLkimtV59pilP2eXDq63O2AIUc1guGiSwbiCQ9u
yl0/tOVu2BTpahiMk+Us6ljFMhAdS7vSGpW8QbmNt9Z0Dh8B9qr3iahQswHP/cEa
Y1NxZz84QZRWb1TZ6x9LHEsqNf3SFM6NIaA+qUnS8fguQaEMBzrkabsgSZ7eHKY5
8ffqEQ8XVpNxqNBiBx3tjVIZmYJLOPsW95QV4VjzU/jjSd++f24M
=tzl8
-----END PGP SIGNATURE-----
Merge tag 'cfi/for-5.17' into mtd/next
Hyperbus changes for v5.17-rc1
Hyperbus changes:
Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
1. Add support for AM64 SoC.
2. Minor improvement: use platform_get_irq().
-----BEGIN PGP SIGNATURE-----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=eb46
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-omap-5.17' into nand/next
Memory controller drivers for v5.17 - OMAP GPMC
1. Add support for AM64 SoC.
2. Minor improvement: use platform_get_irq().
[miquel.raynal@bootlin.com: A first commit introduced a new omap
compatible and another moved the IDs to a header which created a
conflict: moving the new ID as well in the header fixed it.]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI NOR sysfs defines partname and jedec_id device attributes, which
duplicate the information from debugfs. Since the sysfs directory
structure and the attributes in each directory define an ABI between the
kernel and user space, thus it can never be removed, remove the debugfs
entries so that we don't duplicate the information.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211217122636.474976-2-tudor.ambarus@microchip.com
Fixes: 2a734bb8d5 ("UBI: use debugfs for the extra checks knobs")
There is a mistake in docstrings, it should be ubi_debugfs_exit_dev
instead of dbg_debug_exit_dev.
Signed-off-by: Kai Song <songkai01@inspur.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The Octal DTR configuration is stored in the CFR0V register. This
register is 1 byte wide. But 1 byte long transactions are not allowed in
8D-8D-8D mode. The next byte address contains the CFR1V register, which
contains the number of dummy cycles. This is very fortunate since the
enable path changes the value of this register. Reset the value to its
default when disabling Octal DTR mode. This way, both changes to the
flash state made when enabling can be reverted in one single
transaction.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210531181757.19458-4-p.yadav@ti.com
The Octal DTR configuration is stored in the CFR5V register. This
register is 1 byte wide. But 1 byte long transactions are not allowed in
8D-8D-8D mode. Since the next byte address does not contain any
register, it is safe to write any value to it. Write a 0 to it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210531181757.19458-3-p.yadav@ti.com
The template ops used in spi_nor_spimem_check_pp() and
spi_nor_spimem_check_readop() currently set the data phase to 1 byte
long. This is problematic for 8D-8D-8D protocol where odd length data
phase is invalid since one cycle transfers 2 bytes and odd number of
bytes would mean half a cycle is left over. This could result in a
controller rejecting the op as "not supported" even though it actually
supports the protocol.
Change the data length to 2 bytes in these templates. One might argue
that this should only be done for 8D-8D-8D operations but when talking
about these templates, there is no functional difference between one and
two bytes, even in STR modes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210531181757.19458-2-p.yadav@ti.com
Remove the references to the old spi-nor.c file.
The old drivers/mtd/spi-nor/spi-nor.c file
is not more present and now some of its code is contained in:
drivers/mtd/spi-nor/core.c
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
[tudor.ambarus@microchip.com:
- remove change in Documentation/driver-api/mtd/spi-nor.rst.
The documentation has to be rewritten entirely.
- update commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20210126092516.1431913-1-f.suligoi@asem.it
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-3-prabhakar.mahadev-lad.rj@bp.renesas.com
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-2-prabhakar.mahadev-lad.rj@bp.renesas.com
The GPMC device driver is required for NAND controller
to work on K3 Architecture. Select it if required.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-5-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As more compatibles can be added to the GPMC NAND controller driver
use a compatible match table.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-4-rogerq@kernel.org
[krzysztof: remove "is_nand" variable]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Introduce Renesas NAND controller driver which currently supports the
following features on R-Car Gen3 and RZ/N1 SoCs:
- All ONFI timing modes
- Different configurations of its internal ECC controller
- On-die (not tested) and software ECC support
- Several chips (not tested)
- Subpage accesses
- DMA and PIO
This controller was originally provided by Evatronix before being bought
by Cadence.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/linux-mtd/20211217142033.353599-3-miquel.raynal@bootlin.com
This is an assortment of driver patches that rely on some of the changes
in the for-5.17/soc branch. These have all been acked by the respective
maintainers and go through the Tegra tree to more easily handle the
build dependency.
-----BEGIN PGP SIGNATURE-----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=YfSG
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=lWBt
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.17-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
drivers: Changes for v5.17-rc1
This is an assortment of driver patches that rely on some of the changes
in the for-5.17/soc branch. These have all been acked by the respective
maintainers and go through the Tegra tree to more easily handle the
build dependency.
* tag 'tegra-for-5.17-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
media: staging: tegra-vde: Support generic power domain
spi: tegra20-slink: Add OPP support
mtd: rawnand: tegra: Add runtime PM and OPP support
mmc: sdhci-tegra: Add runtime PM and OPP support
pwm: tegra: Add runtime PM and OPP support
bus: tegra-gmi: Add runtime PM and OPP support
usb: chipidea: tegra: Add runtime PM and OPP support
soc/tegra: Add devm_tegra_core_dev_init_opp_table_common()
soc/tegra: Enable runtime PM during OPP state-syncing
Link: https://lore.kernel.org/r/20211217162253.1801077-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In DMA mode we were not considering the force_8bit flag.
Fix it by using regular non-DMA 8-bit I/O if force_8bit flag is set.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211209090458.24830-6-rogerq@kernel.org
The slave_id was previously used to pick one DMA slave instead of another,
but this is now done through the DMA descriptors in device tree.
For the qcom_adm driver, the configuration is documented in the DT
binding to contain a tuple of device identifier and a "crci" field,
but the implementation ends up using only a single cell for identifying
the slave, with the crci getting passed in nonstandard properties of
the device, and passed through the dma driver using the old slave_id
field. Part of the problem apparently is that the nand driver ends up
using only a single DMA request ID, but requires distinct values for
"crci" depending on the type of transfer.
Change both the dmaengine driver and the two slave drivers to allow
the documented binding to work in addition to the ad-hoc passing
of crci values. In order to no longer abuse the slave_id field, pass
the data using the "peripheral_config" mechanism instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-9-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The NAND on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now NAND must be resumed using
runtime PM API in order to initialize the NAND power state. Add runtime PM
and OPP support to the NAND driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In the mtdchar_write_ioctl() function, memdup_user() is called with its
'len' parameter set to verbatim values provided by user space via a
struct mtd_write_req. Both the 'len' and 'ooblen' fields of that
structure are 64-bit unsigned integers, which means the MEMWRITE ioctl
can trigger unbounded kernel memory allocation requests.
Fix by iterating over the buffers provided by user space in a loop,
processing at most mtd->erasesize bytes in each iteration. Adopt some
checks from mtd_check_oob_ops() to retain backward user space
compatibility.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211130113149.21848-1-kernel@kempniu.pl
'chip_map' is a bitmap. So use 'bitmap_zalloc()' to simplify code,
improve the semantic and avoid some open-coded arithmetic in allocator
arguments.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/a6fe58dffe553a3e79303777d3ba9c60d7613c5b.1637510255.git.christophe.jaillet@wanadoo.fr
When developping NAND controller drivers or when debugging filesystem
corruptions, it is quite common to need hacking locally into the
MTD/NAND core in order to get access to the content of the bad
blocks. Instead of having multiple implementations out there let's
provide a simple yet effective specific MTD-wide debugfs entry to fully
disable these checks on purpose.
A warning is added to inform the user when this mode gets enabled.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211118114659.1282855-1-miquel.raynal@bootlin.com
Variable ooblen is being initialized with a value that is never read.
The variable is never used after this, so it is redundant and can be
removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211205230729.79337-1-colin.i.king@gmail.com
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4_4B 0xec,
for erases SPINOR_OP_BE_4K_4B 0x21, and for writes SPINOR_OP_PP_4B 0x12.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-15-tudor.ambarus@microchip.com
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4_4B 0xec,
for erases SPINOR_OP_BE_4K_4B 0x21, and for writes SPINOR_OP_PP_1_1_4_4B
0x34.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-14-tudor.ambarus@microchip.com
s25fl256s0 does not define the SFDP tables nor implements the
RDSFDP 0x5a command. Skip the SFDP parsing in order to avoid
issuing an unsupported command to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-13-tudor.ambarus@microchip.com
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4 0xeb,
for erases SPINOR_OP_BE_4K 0x20, and for writes SPINOR_OP_PP 0x02.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-12-tudor.ambarus@microchip.com
spi_nor_setup() configures the SPI NOR memory. Setting the addr width
is too a configuration, hence we can move the spi_nor_set_addr_width()
in spi_nor_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211207140254.87681-11-tudor.ambarus@microchip.com
New flash additions that support SFDP should be declared with
PARSE_SFDP and with all the other flags that are not SFDP
discoverable.
Keep the old way of initializing the flash, until all the flashes
are converted to use either PARSE_SFDP or SPI_NOR_SKIP_SFDP.
Flashes that declare PARSE_SFDP do not have a roll-back mechanism
because if spi_nor_parse_sfdp() returns an error it means that either
BFPT is not supported, thus SFDP is not supported and the user didn't
correctly declared the flash_info entry, or some memalloc failed.
Either way we should return an error. The rest of the SFDP tables are
optional, if one of the optional SFDP tables fails, we just continue.
We would like to get rid of the default_init() hook, so the
spi_nor_manufacturer_init_params() is not called in the new sequnce
of flash initialization.
Split spi_nor_info_init_params() in spi_nor_init_default_params()
and spi_nor_no_sfdp_init_params(). spi_nor_init_default_params() is
called for all the flashes regardless if they support SFDP or not.
spi_nor_no_sfdp_init_params() is called just for the flashes that
do not define SFDP and initializes parameters and setting solely
based on flash_info data.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-10-tudor.ambarus@microchip.com
Group NOR flags initialization. Introduce a dedicated function for
setting the fixup_flags and emphasise when those flash_info flags
should be set: when the SNOR_F_4B_OPCODES/SNOR_F_IO_MODE_EN_VOLATILE
setttings can not be discovered by SFDP for this particular flash
because the SFDP table that indicates this support is not defined
in the flash.
In case the table for his support is defined but has wrong values,
one should instead use a post_sfdp() hook to set the SNOR_F equivalent
flag.
No functional change intended in this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-9-tudor.ambarus@microchip.com
Used to initialize the NOR flags for settings that are not defined
in the JESD216 SFDP standard, thus can not be retrieved when parsing
SFDP.
This moves the setting of SNOR_F_READY_XSR_RDY and SNOR_F_HAS_LOCK
late in the init call, without any functional change expected.
The rest of the flags were already set after the spi_nor_init_params().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-8-tudor.ambarus@microchip.com
Clarify for what the flash_info flags are used for. Split them in
four categories and a bool:
1/ FLAGS: flags that indicate support that is not defined by the JESD216
standard in its SFDP tables.
2/ NO_SFDP_FLAGS: these flags are used when the flash does not define the
SFDP tables. These flags indicate support that can be discovered via
SFDP. Used together with SPI_NOR_SKIP_SFDP flag.
3/ FIXUP_FLAGS: flags that indicate support that can be discovered
via SFDP ideally, but can not be discovered for this particular flash
because the SFDP table that indicates this support is not defined by
the flash. In case the table for this support is defined but has wrong
values, one should instead use a post_sfdp() hook to set the SNOR_F
equivalent flag.
4/ MFR_FLAGS: manufacturer private flags. Used in the manufacturer
fixup hooks to differentiate support between flashes of the same
manufacturer.
5/ PARSE_SFDP: sets info->parse_sfdp to true. All flash_info entries
that support SFDP should be converted to set info->parse_sfdp to true.
SPI NOR flashes that statically declare one of the
SPI_NOR_{DUAL, QUAD, OCTAL, OCTAL_DTR}_READ flags and do not support
the RDSFDP command are gratuiously receiving the RDSFDP command
in the attempt of parsing the SFDP tables. It is not desirable to issue
commands that are not supported, so introduce PARSE_SFDP to help on this
situation.
New flash additions/updates should be declared/updated to use either
PARSE_SFDP or SPI_NOR_SKIP_SFDP. Once all the flash_info entries are
converted to use SPI_NOR_SKIP_SFDP or PARSE_SFDP, we can get rid of the
SPI_NOR_SKIP_SFDP flag and use just the bool nor->info->parse_sfdp to
determine whether to parse SFDP or not. SPI_NOR_SKIP_SFDP flag is kept
just as a way to differentiate whether a flash is converted to the new
flags logic or not.
Support that can be discovered when parsing SFDP should not be duplicated
by explicit flags at flash declaration. All the flash parameters will be
discovered when parsing SFDP. Sometimes manufacturers wrongly define some
fields in the SFDP tables. If that's the case, SFDP data can be amended
with the fixups() hooks. It is not common, but if the SFDP tables are
entirely wrong, and it does not worth the hassle to tweak the SFDP
parameters by using the fixups hooks, or if the flash does not define the
SFDP tables at all, then statically init the flash with the
SPI_NOR_SKIP_SFDP flag and specify the rest of flash capabilities with
the flash info flags.
With time, we want to convert all flashes to use PARSE_SFDP and
stop triggering the SFDP parsing with the
SPI_NOR_{DUAL, QUAD, OCTAL*}_READ flags. Getting rid of the
SPI_NOR_{OCTAL, OCTAL_DTR}_READ trigger is easily achievable,
the rest are a long term goal.
Manufacturer specific flags like USE_CLSR, USE_FSR, SPI_NOR_XSR_RDY,
will be removed in a future series.
No functional changes intended in this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-7-tudor.ambarus@microchip.com
Used in the manufacturer fixup hooks to differentiate support
between flashes of the same manufacturer. Not used in the
SPI NOR core.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-6-tudor.ambarus@microchip.com
spi_nor_post_sfdp_fixups() was called even when there were no SFDP
tables defined. late_init() should be instead used for flashes that
do not define SFDP tables.
Use spi_nor_post_sfdp_fixups() just to fix SFDP data. post_sfdp()
hook is as of now used just by s28hs512t, mt35xu512aba, and both
support SFDP, there's no functional change with this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-5-tudor.ambarus@microchip.com
Used to init all the mtd_info fields. Move the mtd_info init
the last thing in the spi_nor_scan(), so that we avoid superfluous
initialization of the mtd_info fields in case of errors.
While here use common naming scheme for functions that are setting
mtd_info fields:
s/spi_nor_register_locking_ops/spi_nor_set_mtd_locking_ops
s/spi_nor_otp_init/spi_nor_set_mtd_otp_ops
The functions names are self explanatory, get rid of the comment
for the OTP function.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-4-tudor.ambarus@microchip.com
Linus Torvalds