Add support for the SM8350 SoC, which includes IPA version 4.9.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SC7280 SoC, which includes IPA version 4.11.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SDX55 SoC, which includes IPA version 4.5.
Starting with IPA v4.5, a few of the memory regions have a different
number of "canary" values; update comments in the where the region
identifers are defined to accurately reflect that.
I'll note three differences in SDX55 versus the other two existing
platforms (SDM845 and SC7180):
- SDX55 uses a 32-bit Linux kernel
- SDX55 has four interconnects rather than three
- SDX55 uses IPA v4.5, which uses inline checksum offload
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch avoided doing 64-bit modulo operations by checking
the alignment of some DMA allocations using only the lower 32 bits
of the address.
David Laight pointed out (after the fix was committed) that DMA
allocations might already satisfy the alignment requirements. And
he was right.
Remove the alignment checks that occur after DMA allocation requests,
and update comments to explain why the constraint is satisfied. The
only place IPA_TABLE_ALIGN was used was to check the alignment; it is
therefore no longer needed, so get rid of it.
Add comments where GSI_RING_ELEMENT_SIZE and the tre_count and
event_count channel data fields are defined to make explicit they
are required to be powers of 2.
Revise a comment in gsi_trans_pool_init_dma(), taking into account
that dma_alloc_coherent() guarantees its result is aligned to a page
size (or order thereof).
Don't bother printing an error if a DMA allocation fails.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the SC7180 configuration data file so that its name is
derived from its IPA version.
Update a few other references to the code that talk about the SC7180
rather than just IPA v4.2.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the SDM845 configuration data file so that its name is
derived from its IPA version. I am not aware of any special IPA
behavior or handling that would be based on a specific SoC (as
opposed to a specific version of the IPA it contains).
Update a few other references to the code that talk about the SDM845
rather than just IPA v3.5.1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The backward compatibility register value is a platform-specific
property that is not stored in the platform data. Create a data
field where this can be represented, and get rid ipa_reg_bcr_val().
This register is not present starting with IPA v4.5.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA versions 3.0 and 3.1 support up to 8 resource groups. There is
some interest in supporting these older versions of the hardware, so
update the resource configuration code to program resource limits
for these groups if specified.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arrays of source and destination resource limits defined in
configuration data are of a fixed size--which is the maximum number
of resource groups supported for any platform. Most platforms will
use fewer than that many groups.
Add new members to the ipa_rsrc_group_id enumerated type to define
the number of source and destination resource groups are defined for
the platform. (This type is defined for each platform in its data
file.)
Add a new field to the resource configuration data that indicates
how many of the source and destination resource groups are actually
used for the platform, and initialize it with the count value. This
allows us to determine the number of groups defined for the platform
without exposing the ipa_rsrc_group_id enumerated type.
As a result, we no longer need ipa_resource_group_src_count()
and ipa_resource_group_dst_count(), because each platform now
defines its supported number of resource groups. So get rid of
those two functions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipa_resource_src and ipa_resource_dst structures are identical
in form, so just replace them with a single structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace IPA_RESOURCE_GROUP_SRC_MAX and IPA_RESOURCE_GROUP_DST_MAX
with a single symbol, IPA_RESOURCE_GROUP_MAX.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most platforms have the same set of source and destination resource
types. But some older platforms have some additional ones, and it's
possible different resources will be used in the future.
Move the definition of the ipa_resource_type enumerated type so it
is defined for each platform in its configuration data file. This
permits each to have a distinct set of resources.
Shorten the data files slightly, by putting the min and max limit
values on the same line.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the type field from the ipa_resource_src and ipa_resource_dst
structures, and instead use that value as the index into the arrays
of source and destination resources.
Change ipa_resource_config_src() and ipa_resource_config_dst() so
the resource type is passed in as an argument.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine the ipa_resource_type_src and ipa_resource_type_dst
enumerated types into a single enumerated type, ipa_resource_type.
Assign value 0 to the first element for the source and destination
types, so their numeric values are preserved. Add some additional
commentary where these are defined, stating explicitly that code
assumes the first source and first destination member must have
numeric value 0.
Fix the kerneldoc comments for the ipa_gsi_endpoint_data structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only program the sequencer type for TX endpoints. So move the
definition of the sequencer type fields into the TX-specific portion
of the endpoint configuration data. There's no need to maintain
this in the IPA structure; we can extract it from the configuration
data it points to in the one spot it's needed.
We previously specified the sequencer type for RX endpoints with
INVALID values. These are no longer needed, so get rid of them.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IPA endpoint has a sequencer that must be configured based on how
the endpoint is to be used. Currently the IPA code programs the
sequencer type by splitting a value into four 4-bit nibbles. Doing
that doesn't really add much value, and regardless, a better way of
splitting the sequencer type is into two halves--the lower byte
describing how normal packet processing is handled, and the next
byte describing information about processing replicas.
So split the sequencer type into two sub-parts: the sequencer type
and the replication sequencer type. Define the values supported for
the "main" sequencer type, and define the values supported for the
replication part separately.
In addition, the sequencer type names are quite verbose, encoding
what the type includes, but also what it *excludes*. Rename the
sequencer types in a way that mainly describes the number of passes
that a packet takes through the IPA processing pipeline, and how
many of those passes end by supplying the processed packet to the
microprocessor.
The result expands the supported types beyond what is required for
now, but simplifies the way these are defined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.0, a limit is placed on the number of bytes
outstanding in a transaction, to reduce latency. The limit is
imposed only if this value is non-zero.
We don't use a non-zero value for SC7180, but newer versions of IPA
do. Prepare for that by allowing a programmed value to be specified
in the platform configuration data.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the maximum number of reads and writes to configure for the
QSB masters used for IPA in configuration data.
We don't use these values yet; the next commit takes care of that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we assume that the IPA hardware has exactly three
interconnects. But that won't be guaranteed for all platforms,
so allow any number of interconnects to be specified in the
configuration data.
For each platform, define an array of interconnect data entries
(still associated with the IPA clock structure), and record the
number of entries initialized in that array.
Loop over all entries in this array when initializing, enabling,
disabling, or tearing down the set of interconnects.
With this change we no longer need the ipa_interconnect_id
enumerated type, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the name to the configuration data for each interconnect. Use
this information rather than a constant string during initialization.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use "bandwidth" rather than "rate" in describing the average and
peak values to use for IPA interconnects. They should have been
named that way to begin with.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define a new type of configuration data, used to initialize the
IPA core clock and interconnects. This is the first of three
patches, and defines the data types and interface but doesn't
yet use them.
Switch the return value if there is no matching configuration data
to ENODEV instead of ENOTSUPP (to avoid using the nonstandard errno).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous commit added support for IPA having up to six source
and destination resources. But currently nothing uses more than
four. (Five of each are used in a newer version of the hardware.)
I find that in one of my build environments the compiler complains
about newly-added code in two spots. Inspection shows that the
warnings have no merit, but this compiler does not recognize that.
ipa_main.c:457:39: warning: array index 5 is past the end of the
array (which contains 4 elements) [-Warray-bounds]
(and the same warning at line 483)
We can make this warning go away by changing the number of elements
in the source and destination resource limit arrays--now rather than
waiting until we need it to support the newer hardware. This change
was coming soon anyway; make it now to get rid of the warning.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201031151524.32132-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The number of resource groups supported by the hardware can be
different for source and destination resources. Determine the
number supported for each using separate functions. Make the
functions inline end move their definitions into "ipa_reg.h",
because they determine whether certain register definitions are
valid. Pass just the IPA hardware version as argument.
IPA_RESOURCE_GROUP_COUNT represents the maximum number of resource
groups the driver supports for any hardware version. Change that
symbol to be two separate constants, one for source and the other
for destination resource groups. Rename them to end with "_MAX"
rather than "_COUNT", to reflect their true purpose.
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA hardware manages various resources (e.g. descriptors)
internally to perform its functions. The resources are grouped,
allowing different endpoints to use separate resource pools. This
way one group of endpoints can be configured to operate unaffected
by the resource use of endpoints in a different group.
Endpoints should be assigned to a resource group, but we currently
don't do that.
Define a new resource_group field in the endpoint configuration
data, and use it to assign the proper resource group to use for
each AP endpoint.
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A "delay mode" feature was put in place to work around a problem
that was observed during development of the upstream IPA driver. It
used TX endpoint "delay mode" in order to prevent transmitting
packets toward the modem before it was ready.
A race condition that would explain the problem has long since been
fixed, and we have concluded that the "delay mode" feature is no
longer required. So get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arrange to use an item from SMEM memory for IPA. SMEM item number
497 is designated to be used by the IPA. Specify the item ID and
size of the region in platform configuration data. Allocate and get
a pointer to this region from ipa_mem_init(). The memory must be
mapped for access through an SMMU.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a region of IMEM memory available for use by IPA in the
platform configuration data. Initialize it from ipa_mem_init().
The memory must be mapped for access through an SMMU.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipa_mem_data structure type was never actually used. Instead,
the IPA memory regions were defined using the ipa_mem structure.
Redefine struct ipa_mem_data so it encapsulates the array of IPA-local
memory region descriptors along with the count of entries in that
array. Pass just an ipa_mem structure pointer to ipa_mem_init().
Rename the ipa_mem_data[] array ipa_mem_local_data[] to emphasize
that the memory regions it defines are IPA-local memory.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines configuration data that is used to specify some
of the details of IPA hardware supported by the driver. It is built
as Device Tree match data, discovered at boot time. The driver
supports the Qualcomm SDM845 SoC. Data for the Qualcomm SC7180 is
also defined here, but it is not yet completely supported.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder