New wmi-tlv firmware for qca6174 supports this.
This should fix issues related to multi-vif WMM.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.
This prepares per-vif WMM param setup.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Software encryption was never necessary.
Tested with fw 636 and fw 10.x.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only userspace can make an educated decision when
a trigger frame is required so make sure the
autotrigger service is disabled.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The workaround couldn't work correctly because the
802.11 header wasn't properly stripped of QoS Data
bit so it wasn't recognized in the later parts of
tx path as NullFunc frame and ended up in HTT Tx
instead of HTT Mgmt Tx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware supporting beacon templates (i.e. wmi-tlv
for qca6174) doesn't implicitly take dtim period
from the template. Instead it requires vdev param
to be set accordingly.
This fixes dtim period being stuck at 3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a comment for indicating that the ATH10K_SCAN_RUNNING case falls
through to the ATH10K_SCAN_ABORTING case in __ath10k_scan_finish. This
will document that the lack of a break is intentional.
Coverity: CID 1260017
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions support beacon and probe
response templates instead. This means SWBA events
are no longer delivered for these firmware
revisions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_for_completion_timeout does not return negative values so the tests
for <= 0 are not needed and the case differentiation in the error handling
path unnecessary.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add per station debugfs files when a station is added to mac80211's
station list. This helps to group peer specific debugfs entries
altogether. Right now this callback adds support to test aggregation
procedures (addba/addba_resp/delba) manually.
To enable automatic aggregation in target,
echo 0 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
phymode should use 11b only if NO_OFDM flags is set.
Hence check up channel flag for NO_OFDM and set to
11b.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Assoc peer command contain information about NSS.
When we will get IEEE80211_RC_NSS_CHANGED we should
also send (re) assoc peer command to be sure firmware
will know about it and RC will work correctly.
This was found during code review.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fix TX problem when IBSS used in HT mode.
Before we used 6Mbps all the time for TX direction.
Reported-by: Yeoh Chun-Yeow <yeohchunyeow@gmail.com>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware uses bitmask in wmi_resource_config to configure
10.2 firmware features like airtime fairness and rx batch mode instead
of maintaining separete bool entry. This allows new features that can be
configure during init time without breaking backward compatibility.
kvalo: use WMI op version, bump up FW API to 4 to not break older versions of
ath10k
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ATH10K_FW_FEATURE_WMI_10X should not be used for anymore as that's
now deprecated, instead use wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't allow precise tx rate control so
P2P wasn't entirely spec compliant (it was using
CCK rates in some cases).
The only way to make sure firmware doesn't use CCK
rates is to have a vdev with P2P subtype used for
scanning and tx. This can be done via a special
dedicated P2P device interface support.
This also removes the ancient hack from ath10k in
favor of p2pdev.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per-vif bss_conf.ps should be used to configure
powersave.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting 0 ps timeout to firmware yields very poor
latency and traffic issues. This is the case when
multi-vif is active.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To comply with WMM-PS the device shouldn't wake up
with a NullFunc frame pair when tx-ing. Instead PM
bit on each tx frame should be used.
To make this work correctly firmware needs to be
told to use a different STA PS wake threshold when
u-APSD is enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions need peer phymode to be
specified as MODE_11B when associating as station
to a 11b AP. Otherwise they can starve other
stations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting fragmentation threshold has not been supported by
any of firmware versions, hence unregister the callback and
remove the function.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.
The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Increase the rts threshold from the legacy value of 2347 to support higher
threshold limit.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of peers isn't directly translatable to
the number of stations because ath10k needs to
reserve a few extra peers for special cases like
multi-vif concurrency.
The previous limit was 126 and 15 stations in AP
mode for 10.x and main firmware branches
respectively. The limit is now 128 and 16 which
was the original intention.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The var was supposed to be protected by data_lock
but it wasn't so in all instances. It's actually
not necessary to have a spinlock protected
num_peers so drop it.
All instances of num_peers are already within
conf_mutex sections so use that.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents warning spamming if peer creation
fails during sta_state in some cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_tx_wep_key_work() acquires conf_mutex, so
cancelling it when conf_mutex is already taken
in ath10k_remove_interface() is incorrect, so
move it outside the lock.
Snippet from the lockdep report:
kernel: ======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.18.0-rc5-wl-debug #34 Tainted: G O
kernel: -------------------------------------------------------
kernel: hostapd/451 is trying to acquire lock:
kernel: ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290
kernel: but task is already holding lock:
kernel: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core]
kernel: which lock already depends on the new lock.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
peer->keys needs to be protected by data_lock
since it is also accessed from the WMI path.
Both install() and clear() routines for peer
keys modify the key contents, so use the data_lock
to avoid races.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When static keys are used in shared WEP, when a
station is associated, message 3 is sent with an
encrypted payload. But, for subsequent
authentications that are triggered without a
deauth, the auth frame is decrypted by the HW.
To handle this, check if the WEP keys have already
been set for the peer and if so, mark the
frame as decrypted. This scenario can happen
when a station changes its default TX key and initiates
a new authentication sequence.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When mac80211 requests driver to cancel a hw roc
the driver must not call the expired() callback or
else roc will fail in some cases depending on how
things get scheduled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With P2P concurrency requested hw roc duration
time can be very small. Some firmware revisions
refuse scan requests with too small channel dwell
time.
This prevents messages like, e.g. with connected
STA vif and performing P2P Find:
ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan
ieee80211 phy3: failed to start next HW ROC (-110)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions don't need peer creation
when doing offchannel tx. Earlier revisions would
queue and never release frames without a peer.
This prevent new firmware revisions from stopping
replenishing wmi-htc tx credits and improves
reliability of offchannel tx which would sometimes
silently fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Comment was out-of-date. The headroom is no longer
necessary because HTT Tx fragment list is stored
in dma pool item associated with each sk_buff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When re-associating a station, the nss was set back to
maximum value even if user had configured small number
of tx chains. So, pay attention to user's config in
this case as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It appears it takes more than just setting the
hardware's chainmask to make things work well. Without
this patch, a vdev would only use 1x1 rates when chainmask
was set to 0x3.
Setting the 'nss' (number of spatial streams) on the vdev
helps the firmware's rate-control algorithm work properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions
-----BEGIN PGP SIGNATURE-----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=6GIj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases hw recovery was taking an absurdly
long time due to ath10k waiting for things that
would never really complete.
Instead of waiting for inevitable timeouts poke
all completions and wakequeues and check if it's
still worth waiting.
Reading/writing ar->state requires conf_mutex.
Since waiters might be holding it introduce a new
flag CRASH_FLUSH so it's possible to tell waiters
to abort whatever they were waiting for.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rts threshold was being configured instead of
fragmentation threshold.
Keep in mind available firmware binaries don't
seem to support fragmentation anyway so this
doesn't fix fragmentation threshold per se.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When user space requests survey info, it is useful to know which of the survey
data refers to the channel that is currently actively being used. One of the
use cases is getting the current channel noise for status output. Without this
flag you would have to look up the channel separately and then compare it
against the frequency in the survey output in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This simply changes the source for txpower setup.
It does not make ath10k use different txpower
values for different vifs.
This will make it easier to implement chanctx in
ath10k in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code can be symmetrical so make it so. This
makes it easier to understand and work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to reconfigure peer
completely upon reassociation. This will make it
easier to have a more uniform association code
across different modes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to pass bss_conf explicitly as it
is accessible via vif pointer. This requires
slight changes in function prototypes. While at it
clean up listen interval workaround/command.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Based on GFP flag given to DMA coherent allocation, the behaviour of
dma_free_coherent is changed. This behavioural diffrence is noticeable
in ARM platform. If DMA memory is allocated with GFP_KERNEL, free
coherent can not be called inside spin lock. This is causing kernel
crash in ARM platforms. Fix this by changing GFP flag to atomic.
This is most likely a regression from commit 64badcb6d6 ("ath10k: workaround
fw beaconing bug").
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary to create bssid peer for
bssid. Self-address peer is sufficient.
This prevents some firmware revisions from crashing.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior