Otherwise, we go into an endless busy loop trying to enable PS mode when
the command queue is empty, dealing with the error response, and then
trying to enable PS mode again because the command queue is empty.... it
doesn't really save much power.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_send_confirmwake() is a bit ugly but matches the way we confirm
sleep. We'll deal with that whole thing later.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And handle the case where it times out more than once, too, instead of
locking up for ever.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, check that suspend is refused if HOST_SLEEP_CFG hasn't been done.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking issues with TX, especially TX from multiple netdevs, get
_so_ much easier if you do it like this.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There seems to be no point in doing it as an ieee80211 device instead of
a normal netdev, and when we override its ->priv and then call
free_ieee80211() it has a distressing tendency to crash horribly.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was buggy as hell anyway, since it was just spewing packets at the
device when it wasn't necessarily ready for them (in the USB case, while
the URB was still busy).
We could probably do with a better way of flushing packets to the device
_immediately_, before we stick it back into sleep mode. But we can no
longer just dequeue packets directly, it seems.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There seems to be no reason for a separate structure; move it all
into struct lbs_private.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need this. We can use adapter->currenttxskb instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least it doesn't oops when you attempt to read or write it now.
Only when you enable it and then later turn it off. And when it's
enabled I don't see how it actually works.
But one fewer oops is good, for now...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the code that is used for scanning and makes it hopefully
easier to understand:
* move function into logical blocks
* create a bunch of lbs_scan_add_XXXX_tlv() functions, that
help to create the TLV parameter of CMD_802_11_SCAN
* all of them are now called from the much simpler lbs_do_scan()
* no **puserscancfg double-pointers :-)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New typedefs are usually frowned upon. This patch changes
libertas_adapter -> struct libertas_adapter
libertas_priv -> struct libertas_priv
While passing, make everything checkpatch.pl-clean that gets touches.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Requires firmware version 5.110.19.p0 or newer, available here:
http://dev.laptop.org/pub/firmware/libertas/
Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transmit and receive traffic as soon as the mesh interface is
brought up.
Test case 1: Bring up only the mesh interface and ping. No need for
any iwconfig commands on the main interface.
$ ifconfig msh0 192.168.5.3
$ iwconfig msh0 channel X
$ ping 192.168.5.2
If ping succeeds, PASS
Test case 2: Associate with the main interface, and turn off AP. Mesh
interface should not lose connectivity.
$ iwconfig eth0 mode managed essid "my_ssid"
$ ifconfig msh0 192.168.5.3
$ ping 192.168.5.2
<turn off access point>
If ping continues uninterrupted, PASS
This feature requires firmware version 5.110.19.p0 or newer, available
here: http://dev.laptop.org/pub/firmware/libertas/
Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies the namespace of variables, functions defines
and structures. It does:
- rename libertas_XXX to lbs_XXX
- rename LIBERTAS_XXX to lbs_XXX
- rename wlan_XXX to lbs_XXX
- rename WLAN_XXX to LBS_XXX (but only those that were
defined in libertas-local *.h files, e.g. not defines
from net/ieee80211.h)
While passing, I fixed some checkpatch.pl errors too.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all firmware load responsibility into the interface-specific
code and gets rid of the firmware pointer in the generic card structure. It
also removes 3 fairly unecessary callbacks: hw_register_dev, hw_unregister_dev,
and hw_prog_firmware. It also makes the init sequence from interface
probe functions more logical, as there are paired add/remove and start/stop
calls into generic libertas code.
Because the USB driver code uses the same TX URB callback for both firmware
upload (where the generic libertas structure isn't initialized yet) and for
normal operation (where it is), some bits of USB code have to deal with
'priv' being NULL. All USB firmware upload bits have been changed to not
require 'priv' at all, but simply the USB card structure.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Boot2 version used to be hardcoded in the uploaded firmware,
this patch preserves the boot2 version before uploading firmware
and sends it to the firmware again on resume.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Push WEXT scan requests to a workqueue and have each partial scan queue
the next part, then only report results when the complete scan has finished.
Full scans don't go through the work queue.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver support for the monitor mode support that will be available in the next
OLPC 'bleeding edge' Marvell firmware release (most likely, 5.110.16.p2).
To activate monitor mode,
echo mode > /sys/class/net/{ethX,mshX}/device/libertas_rtap
where mode is the hex mask that specifies which frames to sniff (in short, 0x1
for data, 0x2 for all management but beacons, 0x4 for beacons). Any non zero
mode will activate the monitor mode, inhibiting transmission in ethX and mshX
interfaces and routing all the incoming traffic to a new rtapX interface that
will output the packets in 802.11+radiotap headers format.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After loading the firmware, mesh autostart will be disabled. After that, the
user will still be able to enable or disable it at will. On suspend, it will be
always activated and later on resume it will go back to the state it had before
going to sleep.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
scantype was initialized with CMD_SCAN_TYPE_ACTIVE, but there is no code
that would ever change it, so we can use that variable directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
scanmode was initialized with CMD_BSS_TYPE_ANY, but there is no code
that ever can store another value there, so it can go away.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
beaconperiod was initialized with MRVDRV_BEACON_INTERVAL, but there is
no code that would ever change it's value. We can use the define directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable was initialized with 0 (false). There is no code that would
ever change it, so we can use the false-patch directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
listeninterval was initialized with MRVDRV_DEFAULT_LISTEN_INTERVAL, but
there exists that would ever change it. So we can use this define directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The value was computed, but then never used.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This varaible was initialized with 0 but there is no code that would ever
change it's value. So it can go away.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
multipledtim was initialized with MRVDRV_DEFAULT_MULTIPLE_DTIM and then
kept at that value, so we could use that define directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
locallisteninterval was initialized with 0, but there is no code that
changes it, rendering it rather useless.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No code ever initialized this variable, so it was 0 because of kzalloc().
But no other code changes it, making it rather useless.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those two variables were initialized with some default values, but there
is no code that would ever change them. So we could use as well the defaults
directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No code uses the contents of this variable, so it can go.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The value of txrate was only set by a CMD_802_11_TX_RATE_QUERY command,
but there was no code in the driver that ever issued this command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable was initialized to 0 and nowhere else changed, so basically
the per-packet TX control wasn't used.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable was initialized to 0 and nowhere else to anything
different.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The value 1 was assigned to it and there was nowhere any code
that would have changed that to 0.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was nowhere any code that used the values of those
variables.
This patch also removes two static functions that are now unused.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were just used in some debug output, but nowhere else.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is nowhere any place that set's this variable.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused/duplicated fields and consolidate static data rate arrays,
for example the libertas_supported_rates[] and datarates[] arrays in
the bss_descriptor structure, and the libertas_supported_rates field
in the wlan_adapter structure.
Introduce libertas_fw_index_to_data_rate and libertas_data_rate_to_fw_index
functions and use them everywhere firmware requires a rate index rather
than a rate array.
The firmware requires the 4 basic rates to have the MSB set, but most
other stuff doesn't, like WEXT and mesh ioctls. Therefore, only set the MSB
on basic rates when pushing rate arrays to firmware instead of doing a ton
of (rate & 0x7f) everywhere.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the thread.h abstractions and opencode kthread stuff
to make it clearer.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't touch hardware and therefore doesn't need endian notations
either.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use standard BSS capability field constants from ieee80211.h.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace WLAN_802_11_SSID with direct 'ssid' and 'ssid_len' members
like ieee80211. In the process, remove private libertas_escape_essid
and depend on the ieee80211 implementation of escape_essid instead.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Woodhouse