If we do a direct IO read or write when the buffer given by the user is
memory mapped to the file range we are going to do IO, we end up ending
in a deadlock. This is triggered by the new test case generic/647 from
fstests.
For a direct IO read we get a trace like this:
[967.872718] INFO: task mmap-rw-fault:12176 blocked for more than 120 seconds.
[967.874161] Not tainted 5.14.0-rc7-btrfs-next-95 #1
[967.874909] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[967.875983] task:mmap-rw-fault state:D stack: 0 pid:12176 ppid: 11884 flags:0x00000000
[967.875992] Call Trace:
[967.875999] __schedule+0x3ca/0xe10
[967.876015] schedule+0x43/0xe0
[967.876020] wait_extent_bit.constprop.0+0x1eb/0x260 [btrfs]
[967.876109] ? do_wait_intr_irq+0xb0/0xb0
[967.876118] lock_extent_bits+0x37/0x90 [btrfs]
[967.876150] btrfs_lock_and_flush_ordered_range+0xa9/0x120 [btrfs]
[967.876184] ? extent_readahead+0xa7/0x530 [btrfs]
[967.876214] extent_readahead+0x32d/0x530 [btrfs]
[967.876253] ? lru_cache_add+0x104/0x220
[967.876255] ? kvm_sched_clock_read+0x14/0x40
[967.876258] ? sched_clock_cpu+0xd/0x110
[967.876263] ? lock_release+0x155/0x4a0
[967.876271] read_pages+0x86/0x270
[967.876274] ? lru_cache_add+0x125/0x220
[967.876281] page_cache_ra_unbounded+0x1a3/0x220
[967.876291] filemap_fault+0x626/0xa20
[967.876303] __do_fault+0x36/0xf0
[967.876308] __handle_mm_fault+0x83f/0x15f0
[967.876322] handle_mm_fault+0x9e/0x260
[967.876327] __get_user_pages+0x204/0x620
[967.876332] ? get_user_pages_unlocked+0x69/0x340
[967.876340] get_user_pages_unlocked+0xd3/0x340
[967.876349] internal_get_user_pages_fast+0xbca/0xdc0
[967.876366] iov_iter_get_pages+0x8d/0x3a0
[967.876374] bio_iov_iter_get_pages+0x82/0x4a0
[967.876379] ? lock_release+0x155/0x4a0
[967.876387] iomap_dio_bio_actor+0x232/0x410
[967.876396] iomap_apply+0x12a/0x4a0
[967.876398] ? iomap_dio_rw+0x30/0x30
[967.876414] __iomap_dio_rw+0x29f/0x5e0
[967.876415] ? iomap_dio_rw+0x30/0x30
[967.876420] ? lock_acquired+0xf3/0x420
[967.876429] iomap_dio_rw+0xa/0x30
[967.876431] btrfs_file_read_iter+0x10b/0x140 [btrfs]
[967.876460] new_sync_read+0x118/0x1a0
[967.876472] vfs_read+0x128/0x1b0
[967.876477] __x64_sys_pread64+0x90/0xc0
[967.876483] do_syscall_64+0x3b/0xc0
[967.876487] entry_SYSCALL_64_after_hwframe+0x44/0xae
[967.876490] RIP: 0033:0x7fb6f2c038d6
[967.876493] RSP: 002b:00007fffddf586b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000011
[967.876496] RAX: ffffffffffffffda RBX: 0000000000001000 RCX: 00007fb6f2c038d6
[967.876498] RDX: 0000000000001000 RSI: 00007fb6f2c17000 RDI: 0000000000000003
[967.876499] RBP: 0000000000001000 R08: 0000000000000003 R09: 0000000000000000
[967.876501] R10: 0000000000001000 R11: 0000000000000246 R12: 0000000000000003
[967.876502] R13: 0000000000000000 R14: 00007fb6f2c17000 R15: 0000000000000000
This happens because at btrfs_dio_iomap_begin() we lock the extent range
and return with it locked - we only unlock in the endio callback, at
end_bio_extent_readpage() -> endio_readpage_release_extent(). Then after
iomap called the btrfs_dio_iomap_begin() callback, it triggers the page
faults that resulting in reading the pages, through the readahead callback
btrfs_readahead(), and through there we end to attempt to lock again the
same extent range (or a subrange of what we locked before), resulting in
the deadlock.
For a direct IO write, the scenario is a bit different, and it results in
trace like this:
[1132.442520] run fstests generic/647 at 2021-08-31 18:53:35
[1330.349355] INFO: task mmap-rw-fault:184017 blocked for more than 120 seconds.
[1330.350540] Not tainted 5.14.0-rc7-btrfs-next-95 #1
[1330.351158] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[1330.351900] task:mmap-rw-fault state:D stack: 0 pid:184017 ppid:183725 flags:0x00000000
[1330.351906] Call Trace:
[1330.351913] __schedule+0x3ca/0xe10
[1330.351930] schedule+0x43/0xe0
[1330.351935] btrfs_start_ordered_extent+0x108/0x1c0 [btrfs]
[1330.352020] ? do_wait_intr_irq+0xb0/0xb0
[1330.352028] btrfs_lock_and_flush_ordered_range+0x8c/0x120 [btrfs]
[1330.352064] ? extent_readahead+0xa7/0x530 [btrfs]
[1330.352094] extent_readahead+0x32d/0x530 [btrfs]
[1330.352133] ? lru_cache_add+0x104/0x220
[1330.352135] ? kvm_sched_clock_read+0x14/0x40
[1330.352138] ? sched_clock_cpu+0xd/0x110
[1330.352143] ? lock_release+0x155/0x4a0
[1330.352151] read_pages+0x86/0x270
[1330.352155] ? lru_cache_add+0x125/0x220
[1330.352162] page_cache_ra_unbounded+0x1a3/0x220
[1330.352172] filemap_fault+0x626/0xa20
[1330.352176] ? filemap_map_pages+0x18b/0x660
[1330.352184] __do_fault+0x36/0xf0
[1330.352189] __handle_mm_fault+0x1253/0x15f0
[1330.352203] handle_mm_fault+0x9e/0x260
[1330.352208] __get_user_pages+0x204/0x620
[1330.352212] ? get_user_pages_unlocked+0x69/0x340
[1330.352220] get_user_pages_unlocked+0xd3/0x340
[1330.352229] internal_get_user_pages_fast+0xbca/0xdc0
[1330.352246] iov_iter_get_pages+0x8d/0x3a0
[1330.352254] bio_iov_iter_get_pages+0x82/0x4a0
[1330.352259] ? lock_release+0x155/0x4a0
[1330.352266] iomap_dio_bio_actor+0x232/0x410
[1330.352275] iomap_apply+0x12a/0x4a0
[1330.352278] ? iomap_dio_rw+0x30/0x30
[1330.352292] __iomap_dio_rw+0x29f/0x5e0
[1330.352294] ? iomap_dio_rw+0x30/0x30
[1330.352306] btrfs_file_write_iter+0x238/0x480 [btrfs]
[1330.352339] new_sync_write+0x11f/0x1b0
[1330.352344] ? NF_HOOK_LIST.constprop.0.cold+0x31/0x3e
[1330.352354] vfs_write+0x292/0x3c0
[1330.352359] __x64_sys_pwrite64+0x90/0xc0
[1330.352365] do_syscall_64+0x3b/0xc0
[1330.352369] entry_SYSCALL_64_after_hwframe+0x44/0xae
[1330.352372] RIP: 0033:0x7f4b0a580986
[1330.352379] RSP: 002b:00007ffd34d75418 EFLAGS: 00000246 ORIG_RAX: 0000000000000012
[1330.352382] RAX: ffffffffffffffda RBX: 0000000000001000 RCX: 00007f4b0a580986
[1330.352383] RDX: 0000000000001000 RSI: 00007f4b0a3a4000 RDI: 0000000000000003
[1330.352385] RBP: 00007f4b0a3a4000 R08: 0000000000000003 R09: 0000000000000000
[1330.352386] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000003
[1330.352387] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
Unlike for reads, at btrfs_dio_iomap_begin() we return with the extent
range unlocked, but later when the page faults are triggered and we try
to read the extents, we end up btrfs_lock_and_flush_ordered_range() where
we find the ordered extent for our write, created by the iomap callback
btrfs_dio_iomap_begin(), and we wait for it to complete, which makes us
deadlock since we can't complete the ordered extent without reading the
pages (the iomap code only submits the bio after the pages are faulted
in).
Fix this by setting the nofault attribute of the given iov_iter and retry
the direct IO read/write if we get an -EFAULT error returned from iomap.
For reads, also disable page faults completely, this is because when we
read from a hole or a prealloc extent, we can still trigger page faults
due to the call to iov_iter_zero() done by iomap - at the moment, it is
oblivious to the value of the ->nofault attribute of an iov_iter.
We also need to keep track of the number of bytes written or read, and
pass it to iomap_dio_rw(), as well as use the new flag IOMAP_DIO_PARTIAL.
This depends on the iov_iter and iomap changes introduced in commit
c03098d4b9 ("Merge tag 'gfs2-v5.15-rc5-mmap-fault' of
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2").
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Functions gfs2_file_read_iter and gfs2_file_write_iter are both
accessing the user buffer to write to or read from while holding the
inode glock. In the most basic scenario, that buffer will not be
resident and it will be mapped to the same file. Accessing the buffer
will trigger a page fault, and gfs2 will deadlock trying to take the
same inode glock again while trying to handle that fault.
Fix that and similar, more complex scenarios by disabling page faults
while accessing user buffers. To make this work, introduce a small
amount of new infrastructure and fix some bugs that didn't trigger so
far, with page faults enabled.
-----BEGIN PGP SIGNATURE-----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=WeNd
-----END PGP SIGNATURE-----
Merge tag 'gfs2-v5.15-rc5-mmap-fault' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 mmap + page fault deadlocks fixes from Andreas Gruenbacher:
"Functions gfs2_file_read_iter and gfs2_file_write_iter are both
accessing the user buffer to write to or read from while holding the
inode glock.
In the most basic deadlock scenario, that buffer will not be resident
and it will be mapped to the same file. Accessing the buffer will
trigger a page fault, and gfs2 will deadlock trying to take the same
inode glock again while trying to handle that fault.
Fix that and similar, more complex scenarios by disabling page faults
while accessing user buffers. To make this work, introduce a small
amount of new infrastructure and fix some bugs that didn't trigger so
far, with page faults enabled"
* tag 'gfs2-v5.15-rc5-mmap-fault' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix mmap + page fault deadlocks for direct I/O
iov_iter: Introduce nofault flag to disable page faults
gup: Introduce FOLL_NOFAULT flag to disable page faults
iomap: Add done_before argument to iomap_dio_rw
iomap: Support partial direct I/O on user copy failures
iomap: Fix iomap_dio_rw return value for user copies
gfs2: Fix mmap + page fault deadlocks for buffered I/O
gfs2: Eliminate ip->i_gh
gfs2: Move the inode glock locking to gfs2_file_buffered_write
gfs2: Introduce flag for glock holder auto-demotion
gfs2: Clean up function may_grant
gfs2: Add wrapper for iomap_file_buffered_write
iov_iter: Introduce fault_in_iov_iter_writeable
iov_iter: Turn iov_iter_fault_in_readable into fault_in_iov_iter_readable
gup: Turn fault_in_pages_{readable,writeable} into fault_in_{readable,writeable}
powerpc/kvm: Fix kvm_use_magic_page
iov_iter: Fix iov_iter_get_pages{,_alloc} page fault return value
In order to make 'real_root' used only in ref-verify it's required to
have the necessary context to perform the same checks that this member
is used for. So add 'mod_root' which will contain the root on behalf of
which a delayed ref was created and a 'skip_group' parameter which
will contain callsite-specific override of skip_qgroup.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have a few flags that are inconsistently used to describe the fs in
different states of failure. As of 5963ffcaf3 ("btrfs: always abort
the transaction if we abort a trans handle") we will always set
BTRFS_FS_STATE_ERROR if we abort, so we don't have to check both ABORTED
and ERROR to see if things have gone wrong. Add a helper to check
BTRFS_FS_STATE_ERROR and then convert all checkers of FS_STATE_ERROR to
use the helper.
The TRANS_ABORTED bit check was added in af72273381 ("Btrfs: clean up
resources during umount after trans is aborted") but is not actually
specific.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Although in btrfs we have very limited usage of PageChecked flag, it's
still some page flag not yet subpage compatible.
Fix it by introducing btrfs_subpage::checked_offset to do the convert.
For most call sites, especially for free-space cache, COW fixup and
btrfs_invalidatepage(), they all work in full page mode anyway.
For other call sites, they work as subpage compatible mode.
Some call sites need extra modification:
- btrfs_drop_pages()
Needs extra parameter to get the real range we need to clear checked
flag.
Also since btrfs_drop_pages() will accept pages beyond the dirtied
range, update btrfs_subpage_clamp_range() to handle such case
by setting @len to 0 if the page is beyond target range.
- btrfs_invalidatepage()
We need to call subpage helper before calling __btrfs_releasepage(),
or it will trigger ASSERT() as page->private will be cleared.
- btrfs_verify_data_csum()
In theory we don't need the io_bio->csum check anymore, but it's
won't hurt. Just change the comment.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since setup_items_for_insert() is not used anymore outside of ctree.c,
make it static and remove its prototype from ctree.h. This also requires
to move the definition of setup_item_for_insert() from ctree.h to ctree.c
and move down btrfs_duplicate_item() so that it's defined after
setup_items_for_insert().
Further, since setup_item_for_insert() is used outside ctree.c, rename it
to btrfs_setup_item_for_insert().
This patch is part of a small patchset that is comprised of the following
patches:
btrfs: loop only once over data sizes array when inserting an item batch
btrfs: unexport setup_items_for_insert()
btrfs: use single bulk copy operations when logging directories
This is patch 2/3 and performance results, and the specific tests, are
included in the changelog of patch 3/3.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When inserting a batch of items into a btree, we end up looping over the
data sizes array 3 times:
1) Once in the caller of btrfs_insert_empty_items(), when it populates the
array with the data sizes for each item;
2) Once at btrfs_insert_empty_items() to sum the elements of the data
sizes array and compute the total data size;
3) And then once again at setup_items_for_insert(), where we do exactly
the same as what we do at btrfs_insert_empty_items(), to compute the
total data size.
That is not bad for small arrays, but when the arrays have hundreds of
elements, the time spent on looping is not negligible. For example when
doing batch inserts of delayed items for dir index items or when logging
a directory, it's common to have 200 to 260 dir index items in a single
batch when using a leaf size of 16K and using file names between 8 and 12
characters. For a 64K leaf size, multiply that by 4. Taking into account
that during directory logging or when flushing delayed dir index items we
can have many of those large batches, the time spent on the looping adds
up quickly.
It's also more important to avoid it at setup_items_for_insert(), since
we are holding a write lock on a leaf and, in some cases, on upper nodes
of the btree, which causes us to block other tasks that want to access
the leaf and nodes for longer than necessary.
So change the code so that setup_items_for_insert() and
btrfs_insert_empty_items() no longer compute the total data size, and
instead rely on the caller to supply it. This makes us loop over the
array only once, where we can both populate the data size array and
compute the total data size, taking advantage of spatial and temporal
locality. To make this more manageable, use a structure to contain
all the relevant details for a batch of items (keys array, data sizes
array, total data size, number of items), and use it as an argument
for btrfs_insert_empty_items() and setup_items_for_insert().
This patch is part of a small patchset that is comprised of the following
patches:
btrfs: loop only once over data sizes array when inserting an item batch
btrfs: unexport setup_items_for_insert()
btrfs: use single bulk copy operations when logging directories
This is patch 1/3 and performance results, and the specific tests, are
included in the changelog of patch 3/3.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a done_before argument to iomap_dio_rw that indicates how much of
the request has already been transferred. When the request succeeds, we
report that done_before additional bytes were tranferred. This is
useful for finishing a request asynchronously when part of the request
has already been completed synchronously.
We'll use that to allow iomap_dio_rw to be used with page faults
disabled: when a page fault occurs while submitting a request, we
synchronously complete the part of the request that has already been
submitted. The caller can then take care of the page fault and call
iomap_dio_rw again for the rest of the request, passing in the number of
bytes already tranferred.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Turn iov_iter_fault_in_readable into a function that returns the number
of bytes not faulted in, similar to copy_to_user, instead of returning a
non-zero value when any of the requested pages couldn't be faulted in.
This supports the existing users that require all pages to be faulted in
as well as new users that are happy if any pages can be faulted in.
Rename iov_iter_fault_in_readable to fault_in_iov_iter_readable to make
sure this change doesn't silently break things.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Error injection testing uncovered a case where we'd end up with a
corrupt file system with a missing extent in the middle of a file. This
occurs because the if statement to decide if we should abort is wrong.
The only way we would abort in this case is if we got a ret !=
-EOPNOTSUPP and we called from the file clone code. However the
prealloc code uses this path too. Instead we need to abort if there is
an error, and the only error we _don't_ abort on is -EOPNOTSUPP and only
if we came from the clone file code.
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
I hit a stuck relocation on btrfs/061 during my overnight testing. This
turned out to be because we had left over extent entries in our extent
root for a data reloc inode that no longer existed. This happened
because in btrfs_drop_extents() we only update refs if we have SHAREABLE
set or we are the tree_root. This regression was introduced by
aeb935a455 ("btrfs: don't set SHAREABLE flag for data reloc tree")
where we stopped setting SHAREABLE for the data reloc tree.
The problem here is we actually do want to update extent references for
data extents in the data reloc tree, in fact we only don't want to
update extent references if the file extents are in the log tree.
Update this check to only skip updating references in the case of the
log tree.
This is relatively rare, because you have to be running scrub at the
same time, which is what btrfs/061 does. The data reloc inode has its
extents pre-allocated, and then we copy the extent into the
pre-allocated chunks. We theoretically should never be calling
btrfs_drop_extents() on a data reloc inode. The exception of course is
with scrub, if our pre-allocated extent falls inside of the block group
we are scrubbing, then the block group will be marked read only and we
will be forced to cow that extent. This means we will call
btrfs_drop_extents() on that range when we COW that file extent.
This isn't really problematic if we do this, the data reloc inode
requires that our extent lengths match exactly with the extent we are
copying, thankfully we validate the extent is correct with
get_new_location(), so if we happen to COW only part of the extent we
won't link it in when we do the relocation, so we are safe from any
other shenanigans that arise because of this interaction with scrub.
Fixes: aeb935a455 ("btrfs: don't set SHAREABLE flag for data reloc tree")
CC: stable@vger.kernel.org # 5.8+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add support for fsverity in btrfs. To support the generic interface in
fs/verity, we add two new item types in the fs tree for inodes with
verity enabled. One stores the per-file verity descriptor and btrfs
verity item and the other stores the Merkle tree data itself.
Verity checking is done in end_page_read just before a page is marked
uptodate. This naturally handles a variety of edge cases like holes,
preallocated extents, and inline extents. Some care needs to be taken to
not try to verity pages past the end of the file, which are accessed by
the generic buffered file reading code under some circumstances like
reading to the end of the last page and trying to read again. Direct IO
on a verity file falls back to buffered reads.
Verity relies on PageChecked for the Merkle tree data itself to avoid
re-walking up shared paths in the tree. For this reason, we need to
cache the Merkle tree data. Since the file is immutable after verity is
turned on, we can cache it at an index past EOF.
Use the new inode ro_flags to store verity on the inode item, so that we
can enable verity on a file, then rollback to an older kernel and still
mount the file system and read the file. Since we can't safely write the
file anymore without ruining the invariants of the Merkle tree, we mark
a ro_compat flag on the file system when a file has verity enabled.
Acked-by: Eric Biggers <ebiggers@google.com>
Co-developed-by: Chris Mason <clm@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
There is a possible use-after-free bug when running generic/095.
BUG: Unable to handle kernel data access on write at 0x6b6b6b6b6b6b725b
Faulting instruction address: 0xc000000000283654
c000000000283078 do_raw_spin_unlock+0x88/0x230
c0000000012b1e14 _raw_spin_unlock_irqrestore+0x44/0x90
c000000000a918dc btrfs_subpage_clear_writeback+0xac/0xe0
c0000000009e0458 end_bio_extent_writepage+0x158/0x270
c000000000b6fd14 bio_endio+0x254/0x270
c0000000009fc0f0 btrfs_end_bio+0x1a0/0x200
c000000000b6fd14 bio_endio+0x254/0x270
c000000000b781fc blk_update_request+0x46c/0x670
c000000000b8b394 blk_mq_end_request+0x34/0x1d0
c000000000d82d1c lo_complete_rq+0x11c/0x140
c000000000b880a4 blk_complete_reqs+0x84/0xb0
c0000000012b2ca4 __do_softirq+0x334/0x680
c0000000001dd878 irq_exit+0x148/0x1d0
c000000000016f4c do_IRQ+0x20c/0x240
c000000000009240 hardware_interrupt_common_virt+0x1b0/0x1c0
[CAUSE]
There is very small race window like the following in generic/095.
Thread 1 | Thread 2
--------------------------------+------------------------------------
end_bio_extent_writepage() | btrfs_releasepage()
|- spin_lock_irqsave() | |
|- end_page_writeback() | |
| | |- if (PageWriteback() ||...)
| | |- clear_page_extent_mapped()
| | |- kfree(subpage);
|- spin_unlock_irqrestore().
The race can also happen between writeback and btrfs_invalidatepage(),
although that would be much harder as btrfs_invalidatepage() has much
more work to do before the clear_page_extent_mapped() call.
[FIX]
Here we "wait" for the subapge spinlock to be released before we detach
subpage structure.
So this patch will introduce a new function, wait_subpage_spinlock(), to
do the "wait" by acquiring the spinlock and release it.
Since the caller has ensured the page is not dirty nor writeback, and
page is already locked, the only way to hold the subpage spinlock is
from endio function.
Thus we only need to acquire the spinlock to wait for any existing
holder.
Reported-by: Ritesh Harjani <riteshh@linux.ibm.com>
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
When running generic/095, there is a high chance to crash with subpage
data RW support:
assertion failed: PagePrivate(page) && page->private
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.h:3403!
Internal error: Oops - BUG: 0 [#1] SMP
CPU: 1 PID: 3567 Comm: fio Tainted: 5.12.0-rc7-custom+ #17
Hardware name: Khadas VIM3 (DT)
Call trace:
assertfail.constprop.0+0x28/0x2c [btrfs]
btrfs_subpage_assert+0x80/0xa0 [btrfs]
btrfs_subpage_set_uptodate+0x34/0xec [btrfs]
btrfs_page_clamp_set_uptodate+0x74/0xa4 [btrfs]
btrfs_dirty_pages+0x160/0x270 [btrfs]
btrfs_buffered_write+0x444/0x630 [btrfs]
btrfs_direct_write+0x1cc/0x2d0 [btrfs]
btrfs_file_write_iter+0xc0/0x160 [btrfs]
new_sync_write+0xe8/0x180
vfs_write+0x1b4/0x210
ksys_pwrite64+0x7c/0xc0
__arm64_sys_pwrite64+0x24/0x30
el0_svc_common.constprop.0+0x70/0x140
do_el0_svc+0x28/0x90
el0_svc+0x2c/0x54
el0_sync_handler+0x1a8/0x1ac
el0_sync+0x170/0x180
Code: f0000160 913be042 913c4000 955444bc (d4210000)
---[ end trace 3fdd39f4cccedd68 ]---
[CAUSE]
Although prepare_pages() calls find_or_create_page(), which returns the
page locked, but in later prepare_uptodate_page() calls, we may call
btrfs_readpage() which will unlock the page before it returns.
This leaves a window where btrfs_releasepage() can sneak in and release
the page, clearing page->private and causing above ASSERT().
[FIX]
In prepare_uptodate_page(), we should not only check page->mapping, but
also PagePrivate() to ensure we are still holding the correct page which
has proper fs context setup.
Reported-by: Ritesh Harjani <riteshh@linux.ibm.com>
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pull iov_iter updates from Al Viro:
"iov_iter cleanups and fixes.
There are followups, but this is what had sat in -next this cycle. IMO
the macro forest in there became much thinner and easier to follow..."
* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
csum_and_copy_to_pipe_iter(): leave handling of csum_state to caller
clean up copy_mc_pipe_to_iter()
pipe_zero(): we don't need no stinkin' kmap_atomic()...
iov_iter: clean csum_and_copy_...() primitives up a bit
copy_page_from_iter(): don't need kmap_atomic() for kvec/bvec cases
copy_page_to_iter(): don't bother with kmap_atomic() for bvec/kvec cases
iterate_xarray(): only of the first iteration we might get offset != 0
pull handling of ->iov_offset into iterate_{iovec,bvec,xarray}
iov_iter: make iterator callbacks use base and len instead of iovec
iov_iter: make the amount already copied available to iterator callbacks
iov_iter: get rid of separate bvec and xarray callbacks
iov_iter: teach iterate_{bvec,xarray}() about possible short copies
iterate_bvec(): expand bvec.h macro forest, massage a bit
iov_iter: unify iterate_iovec and iterate_kvec
iov_iter: massage iterate_iovec and iterate_kvec to logics similar to iterate_bvec
iterate_and_advance(): get rid of magic in case when n is 0
csum_and_copy_to_iter(): massage into form closer to csum_and_copy_from_iter()
iov_iter: replace iov_iter_copy_from_user_atomic() with iterator-advancing variant
[xarray] iov_iter_npages(): just use DIV_ROUND_UP()
iov_iter_npages(): don't bother with iterate_all_kinds()
...
By way of inverting the list_empty conditional the insert label can be
eliminated, making the function's flow entirely linear.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
With current subpage RW support, the following script can hang the fs
with 64K page size.
# mkfs.btrfs -f -s 4k $dev
# mount $dev -o nospace_cache $mnt
# fsstress -w -n 50 -p 1 -s 1607749395 -d $mnt
The kernel will do an infinite loop in btrfs_punch_hole_lock_range().
[CAUSE]
In btrfs_punch_hole_lock_range() we:
- Truncate page cache range
- Lock extent io tree
- Wait any ordered extents in the range.
We exit the loop until we meet all the following conditions:
- No ordered extent in the lock range
- No page is in the lock range
The latter condition has a pitfall, it only works for sector size ==
PAGE_SIZE case.
While can't handle the following subpage case:
0 32K 64K 96K 128K
| |///////||//////| ||
lockstart=32K
lockend=96K - 1
In this case, although the range crosses 2 pages,
truncate_pagecache_range() will invalidate no page at all, but only zero
the [32K, 96K) range of the two pages.
Thus filemap_range_has_page(32K, 96K-1) will always return true, thus we
will never meet the loop exit condition.
[FIX]
Fix the problem by doing page alignment for the lock range.
Function filemap_range_has_page() has already handled lend < lstart
case, we only need to round up @lockstart, and round_down @lockend for
truncate_pagecache_range().
This modification should not change any thing for sector size ==
PAGE_SIZE case, as in that case our range is already page aligned.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since the extent io tree operations in btrfs_dirty_pages() are already
subpage compatible, we only need to make the page status update to use
subpage helpers.
Tested-by: Ritesh Harjani <riteshh@linux.ibm.com> # [ppc64]
Tested-by: Anand Jain <anand.jain@oracle.com> # [aarch64]
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of calling list_entry with head->prev simply call
list_last_entry which makes it obvious which member of the list is
being referred. This allows to remove the extra 'prev' pointer.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Replacement is called copy_page_from_iter_atomic(); unlike the old primitive the
callers do *not* need to do iov_iter_advance() after it. In case when they end
up consuming less than they'd been given they need to do iov_iter_revert() on
everything they had not consumed. That, however, needs to be done only on slow
paths.
All in-tree callers converted. And that kills the last user of iterate_all_kinds()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We always return 0 even in case of an error in btrfs_mark_extent_written().
Fix it to return proper error value in case of a failure. All callers
handle it.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing a fast fsync on a file, there is a race which can result in the
fsync returning success to user space without logging the inode and without
durably persisting new data.
The following example shows one possible scenario for this:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ touch /mnt/bar
$ xfs_io -f -c "pwrite -S 0xab 0 1M" -c "fsync" /mnt/baz
# Now we have:
# file bar == inode 257
# file baz == inode 258
$ mv /mnt/baz /mnt/foo
# Now we have:
# file bar == inode 257
# file foo == inode 258
$ xfs_io -c "pwrite -S 0xcd 0 1M" /mnt/foo
# fsync bar before foo, it is important to trigger the race.
$ xfs_io -c "fsync" /mnt/bar
$ xfs_io -c "fsync" /mnt/foo
# After this:
# inode 257, file bar, is empty
# inode 258, file foo, has 1M filled with 0xcd
<power failure>
# Replay the log:
$ mount /dev/sdc /mnt
# After this point file foo should have 1M filled with 0xcd and not 0xab
The following steps explain how the race happens:
1) Before the first fsync of inode 258, when it has the "baz" name, its
->logged_trans is 0, ->last_sub_trans is 0 and ->last_log_commit is -1.
The inode also has the full sync flag set;
2) After the first fsync, we set inode 258 ->logged_trans to 6, which is
the generation of the current transaction, and set ->last_log_commit
to 0, which is the current value of ->last_sub_trans (done at
btrfs_log_inode()).
The full sync flag is cleared from the inode during the fsync.
The log sub transaction that was committed had an ID of 0 and when we
synced the log, at btrfs_sync_log(), we incremented root->log_transid
from 0 to 1;
3) During the rename:
We update inode 258, through btrfs_update_inode(), and that causes its
->last_sub_trans to be set to 1 (the current log transaction ID), and
->last_log_commit remains with a value of 0.
After updating inode 258, because we have previously logged the inode
in the previous fsync, we log again the inode through the call to
btrfs_log_new_name(). This results in updating the inode's
->last_log_commit from 0 to 1 (the current value of its
->last_sub_trans).
The ->last_sub_trans of inode 257 is updated to 1, which is the ID of
the next log transaction;
4) Then a buffered write against inode 258 is made. This leaves the value
of ->last_sub_trans as 1 (the ID of the current log transaction, stored
at root->log_transid);
5) Then an fsync against inode 257 (or any other inode other than 258),
happens. This results in committing the log transaction with ID 1,
which results in updating root->last_log_commit to 1 and bumping
root->log_transid from 1 to 2;
6) Then an fsync against inode 258 starts. We flush delalloc and wait only
for writeback to complete, since the full sync flag is not set in the
inode's runtime flags - we do not wait for ordered extents to complete.
Then, at btrfs_sync_file(), we call btrfs_inode_in_log() before the
ordered extent completes. The call returns true:
static inline bool btrfs_inode_in_log(...)
{
bool ret = false;
spin_lock(&inode->lock);
if (inode->logged_trans == generation &&
inode->last_sub_trans <= inode->last_log_commit &&
inode->last_sub_trans <= inode->root->last_log_commit)
ret = true;
spin_unlock(&inode->lock);
return ret;
}
generation has a value of 6 (fs_info->generation), ->logged_trans also
has a value of 6 (set when we logged the inode during the first fsync
and when logging it during the rename), ->last_sub_trans has a value
of 1, set during the rename (step 3), ->last_log_commit also has a
value of 1 (set in step 3) and root->last_log_commit has a value of 1,
which was set in step 5 when fsyncing inode 257.
As a consequence we don't log the inode, any new extents and do not
sync the log, resulting in a data loss if a power failure happens
after the fsync and before the current transaction commits.
Also, because we do not log the inode, after a power failure the mtime
and ctime of the inode do not match those we had before.
When the ordered extent completes before we call btrfs_inode_in_log(),
then the call returns false and we log the inode and sync the log,
since at the end of ordered extent completion we update the inode and
set ->last_sub_trans to 2 (the value of root->log_transid) and
->last_log_commit to 1.
This problem is found after removing the check for the emptiness of the
inode's list of modified extents in the recent commit 209ecbb858
("btrfs: remove stale comment and logic from btrfs_inode_in_log()"),
added in the 5.13 merge window. However checking the emptiness of the
list is not really the way to solve this problem, and was never intended
to, because while that solves the problem for COW writes, the problem
persists for NOCOW writes because in that case the list is always empty.
In the case of NOCOW writes, even though we wait for the writeback to
complete before returning from btrfs_sync_file(), we end up not logging
the inode, which has a new mtime/ctime, and because we don't sync the log,
we never issue disk barriers (send REQ_PREFLUSH to the device) since that
only happens when we sync the log (when we write super blocks at
btrfs_sync_log()). So effectively, for a NOCOW case, when we return from
btrfs_sync_file() to user space, we are not guaranteeing that the data is
durably persisted on disk.
Also, while the example above uses a rename exchange to show how the
problem happens, it is not the only way to trigger it. An alternative
could be adding a new hard link to inode 258, since that also results
in calling btrfs_log_new_name() and updating the inode in the log.
An example reproducer using the addition of a hard link instead of a
rename operation:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ touch /mnt/bar
$ xfs_io -f -c "pwrite -S 0xab 0 1M" -c "fsync" /mnt/foo
$ ln /mnt/foo /mnt/foo_link
$ xfs_io -c "pwrite -S 0xcd 0 1M" /mnt/foo
$ xfs_io -c "fsync" /mnt/bar
$ xfs_io -c "fsync" /mnt/foo
<power failure>
# Replay the log:
$ mount /dev/sdc /mnt
# After this point file foo often has 1M filled with 0xab and not 0xcd
The reasons leading to the final fsync of file foo, inode 258, not
persisting the new data are the same as for the previous example with
a rename operation.
So fix by never skipping logging and log syncing when there are still any
ordered extents in flight. To avoid making the conditional if statement
that checks if logging an inode is needed harder to read, place all the
logic into an helper function with separate if statements to make it more
manageable and easier to read.
A test case for fstests will follow soon.
For NOCOW writes, the problem existed before commit b5e6c3e170
("btrfs: always wait on ordered extents at fsync time"), introduced in
kernel 4.19, then it went away with that commit since we started to always
wait for ordered extent completion before logging.
The problem came back again once the fast fsync path was changed again to
avoid waiting for ordered extent completion, in commit 487781796d
("btrfs: make fast fsyncs wait only for writeback"), added in kernel 5.10.
However, for COW writes, the race only happens after the recent
commit 209ecbb858 ("btrfs: remove stale comment and logic from
btrfs_inode_in_log()"), introduced in the 5.13 merge window. For NOCOW
writes, the bug existed before that commit. So tag 5.10+ as the release
for stable backports.
CC: stable@vger.kernel.org # 5.10+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In commit d77815461f ("btrfs: Avoid trucating page or punching hole
in a already existed hole."), existing holes can be skipped by calling
find_first_non_hole() to adjust start and len. However, if the given len
is invalid and large, when an EXTENT_MAP_HOLE extent is found, len will
not be set to zero because (em->start + em->len) is less than
(start + len). Then the ret will be 1 but len will not be set to 0.
The propagated non-zero ret will result in fallocate failure.
In the while-loop of btrfs_replace_file_extents(), len is not updated
every time before it calls find_first_non_hole(). That is, after
btrfs_drop_extents() successfully drops the last non-hole file extent,
it may fail with ENOSPC when attempting to drop a file extent item
representing a hole. The problem can happen. After it calls
find_first_non_hole(), the cur_offset will be adjusted to be larger
than or equal to end. However, since the len is not set to zero, the
break-loop condition (ret && !len) will not be met. After it leaves the
while-loop, fallocate will return 1, which is an unexpected return
value.
We're not able to construct a reproducible way to let
btrfs_drop_extents() fail with ENOSPC after it drops the last non-hole
file extent but with remaining holes left. However, it's quite easy to
fix. We just need to update and check the len every time before we call
find_first_non_hole(). To make the while loop more readable, we also
pull the variable updates to the bottom of loop like this:
while (cur_offset < end) {
...
// update cur_offset & len
// advance cur_offset & len in hole-punching case if needed
}
Reported-by: Robbie Ko <robbieko@synology.com>
Fixes: d77815461f ("btrfs: Avoid trucating page or punching hole in a already existed hole.")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There is a comment at btrfs_replace_file_extents() that mentions that we
set the full sync flag on an inode when cloning into a file with a size
greater than or equals to 16MiB, through try_release_extent_mapping() when
we truncate the page cache after replacing file extents during a clone
operation.
That is not true anymore since commit 5e548b3201 ("btrfs: do not set
the full sync flag on the inode during page release"), so update the
comment to remove that part and rephrase it slightly to make it more
clear why the full sync flag is set at btrfs_replace_file_extents().
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have a race between marking that an inode needs to be logged, either
at btrfs_set_inode_last_trans() or at btrfs_page_mkwrite(), and between
btrfs_sync_log(). The following steps describe how the race happens.
1) We are at transaction N;
2) Inode I was previously fsynced in the current transaction so it has:
inode->logged_trans set to N;
3) The inode's root currently has:
root->log_transid set to 1
root->last_log_commit set to 0
Which means only one log transaction was committed to far, log
transaction 0. When a log tree is created we set ->log_transid and
->last_log_commit of its parent root to 0 (at btrfs_add_log_tree());
4) One more range of pages is dirtied in inode I;
5) Some task A starts an fsync against some other inode J (same root), and
so it joins log transaction 1.
Before task A calls btrfs_sync_log()...
6) Task B starts an fsync against inode I, which currently has the full
sync flag set, so it starts delalloc and waits for the ordered extent
to complete before calling btrfs_inode_in_log() at btrfs_sync_file();
7) During ordered extent completion we have btrfs_update_inode() called
against inode I, which in turn calls btrfs_set_inode_last_trans(),
which does the following:
spin_lock(&inode->lock);
inode->last_trans = trans->transaction->transid;
inode->last_sub_trans = inode->root->log_transid;
inode->last_log_commit = inode->root->last_log_commit;
spin_unlock(&inode->lock);
So ->last_trans is set to N and ->last_sub_trans set to 1.
But before setting ->last_log_commit...
8) Task A is at btrfs_sync_log():
- it increments root->log_transid to 2
- starts writeback for all log tree extent buffers
- waits for the writeback to complete
- writes the super blocks
- updates root->last_log_commit to 1
It's a lot of slow steps between updating root->log_transid and
root->last_log_commit;
9) The task doing the ordered extent completion, currently at
btrfs_set_inode_last_trans(), then finally runs:
inode->last_log_commit = inode->root->last_log_commit;
spin_unlock(&inode->lock);
Which results in inode->last_log_commit being set to 1.
The ordered extent completes;
10) Task B is resumed, and it calls btrfs_inode_in_log() which returns
true because we have all the following conditions met:
inode->logged_trans == N which matches fs_info->generation &&
inode->last_subtrans (1) <= inode->last_log_commit (1) &&
inode->last_subtrans (1) <= root->last_log_commit (1) &&
list inode->extent_tree.modified_extents is empty
And as a consequence we return without logging the inode, so the
existing logged version of the inode does not point to the extent
that was written after the previous fsync.
It should be impossible in practice for one task be able to do so much
progress in btrfs_sync_log() while another task is at
btrfs_set_inode_last_trans() right after it reads root->log_transid and
before it reads root->last_log_commit. Even if kernel preemption is enabled
we know the task at btrfs_set_inode_last_trans() can not be preempted
because it is holding the inode's spinlock.
However there is another place where we do the same without holding the
spinlock, which is in the memory mapped write path at:
vm_fault_t btrfs_page_mkwrite(struct vm_fault *vmf)
{
(...)
BTRFS_I(inode)->last_trans = fs_info->generation;
BTRFS_I(inode)->last_sub_trans = BTRFS_I(inode)->root->log_transid;
BTRFS_I(inode)->last_log_commit = BTRFS_I(inode)->root->last_log_commit;
(...)
So with preemption happening after setting ->last_sub_trans and before
setting ->last_log_commit, it is less of a stretch to have another task
do enough progress at btrfs_sync_log() such that the task doing the memory
mapped write ends up with ->last_sub_trans and ->last_log_commit set to
the same value. It is still a big stretch to get there, as the task doing
btrfs_sync_log() has to start writeback, wait for its completion and write
the super blocks.
So fix this in two different ways:
1) For btrfs_set_inode_last_trans(), simply set ->last_log_commit to the
value of ->last_sub_trans minus 1;
2) For btrfs_page_mkwrite() only set the inode's ->last_sub_trans, just
like we do for buffered and direct writes at btrfs_file_write_iter(),
which is all we need to make sure multiple writes and fsyncs to an
inode in the same transaction never result in an fsync missing that
the inode changed and needs to be logged. Turn this into a helper
function and use it both at btrfs_page_mkwrite() and at
btrfs_file_write_iter() - this also fixes the problem that at
btrfs_page_mkwrite() we were setting those fields without the
protection of the inode's spinlock.
This is an extremely unlikely race to happen in practice.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing an fsync we flush all delalloc, lock the inode (VFS lock), flush
any new delalloc that might have been created before taking the lock and
then wait either for the ordered extents to complete or just for the
writeback to complete (depending on whether the full sync flag is set or
not). We then start logging the inode and assume that while we are doing it
no one else is touching the inode's file extent items (or adding new ones).
That is generally true because all operations that modify an inode acquire
the inode's lock first, including buffered and direct IO writes. However
there is one exception: memory mapped writes, which do not and can not
acquire the inode's lock.
This can cause two types of issues: ending up logging file extent items
with overlapping ranges, which is detected by the tree checker and will
result in aborting the transaction when starting writeback for a log
tree's extent buffers, or a silent corruption where we log a version of
the file that never existed.
Scenario 1 - logging overlapping extents
The following steps explain how we can end up with file extents items with
overlapping ranges in a log tree due to a race between a fsync and memory
mapped writes:
1) Task A starts an fsync on inode X, which has the full sync runtime flag
set. First it starts by flushing all delalloc for the inode;
2) Task A then locks the inode and flushes any other delalloc that might
have been created after the previous flush and waits for all ordered
extents to complete;
3) In the inode's root we have the following leaf:
Leaf N, generation == current transaction id:
---------------------------------------------------------
| (...) [ file extent item, offset 640K, length 128K ] |
---------------------------------------------------------
The last file extent item in leaf N covers the file range from 640K to
768K;
4) Task B does a memory mapped write for the page corresponding to the
file range from 764K to 768K;
5) Task A starts logging the inode. At copy_inode_items_to_log() it uses
btrfs_search_forward() to search for leafs modified in the current
transaction that contain items for the inode. It finds leaf N and copies
all the inode items from that leaf into the log tree.
Now the log tree has a copy of the last file extent item from leaf N.
At the end of the while loop at copy_inode_items_to_log(), we have the
minimum key set to:
min_key.objectid = <inode X number>
min_key.type = BTRFS_EXTENT_DATA_KEY
min_key.offset = 640K
Then we increment the key's offset by 1 so that the next call to
btrfs_search_forward() leaves us at the first key greater than the key
we just processed.
But before btrfs_search_forward() is called again...
6) Dellaloc for the page at offset 764K, dirtied by task B, is started.
It can be started for several reasons:
- The async reclaim task is attempting to satisfy metadata or data
reservation requests, and it has reached a point where it decided
to flush delalloc;
- Due to memory pressure the VMM triggers writeback of dirty pages;
- The system call sync_file_range(2) is called from user space.
7) When the respective ordered extent completes, it trims the length of
the existing file extent item for file offset 640K from 128K to 124K,
and a new file extent item is added with a key offset of 764K and a
length of 4K;
8) Task A calls btrfs_search_forward(), which returns us a path pointing
to the leaf (can be leaf N or some other) containing the new file extent
item for file offset 764K.
We end up copying this item to the log tree, which overlaps with the
last copied file extent item, which covers the file range from 640K to
768K.
When writeback is triggered for log tree's extent buffers, the issue
will be detected by the tree checker which will dump a trace and an
error message on dmesg/syslog. If the writeback is triggered when
syncing the log, which typically is, then we also end up aborting the
current transaction.
This is the same type of problem fixed in 0c713cbab6 ("Btrfs: fix race
between ranged fsync and writeback of adjacent ranges").
Scenario 2 - logging a version of the file that never existed
This scenario only happens when using the NO_HOLES feature and results in
a silent corruption, in the sense that is not detectable by 'btrfs check'
or the tree checker:
1) We have an inode I with a size of 1M and two file extent items, one
covering an extent with disk_bytenr == X for the file range [0, 512K)
and another one covering another extent with disk_bytenr == Y for the
file range [512K, 1M);
2) A hole is punched for the file range [512K, 1M);
3) Task A starts an fsync of inode I, which has the full sync runtime flag
set. It starts by flushing all existing delalloc, locks the inode (VFS
lock), starts any new delalloc that might have been created before
taking the lock and waits for all ordered extents to complete;
4) Some other task does a memory mapped write for the page corresponding to
the file range [640K, 644K) for example;
5) Task A then logs all items of the inode with the call to
copy_inode_items_to_log();
6) In the meanwhile delalloc for the range [640K, 644K) is started. It can
be started for several reasons:
- The async reclaim task is attempting to satisfy metadata or data
reservation requests, and it has reached a point where it decided
to flush delalloc;
- Due to memory pressure the VMM triggers writeback of dirty pages;
- The system call sync_file_range(2) is called from user space.
7) The ordered extent for the range [640K, 644K) completes and a file
extent item for that range is added to the subvolume tree, pointing
to a 4K extent with a disk_bytenr == Z;
8) Task A then calls btrfs_log_holes(), to scan for implicit holes in
the subvolume tree. It finds two implicit holes:
- one for the file range [512K, 640K)
- one for the file range [644K, 1M)
As a result we end up neither logging a hole for the range [640K, 644K)
nor logging the file extent item with a disk_bytenr == Z.
This means that if we have a power failure and replay the log tree we
end up getting the following file extent layout:
[ disk_bytenr X ] [ hole ] [ disk_bytenr Y ] [ hole ]
0 512K 512K 640K 640K 644K 644K 1M
Which does not corresponding to any layout the file ever had before
the power failure. The only two valid layouts would be:
[ disk_bytenr X ] [ hole ]
0 512K 512K 1M
and
[ disk_bytenr X ] [ hole ] [ disk_bytenr Z ] [ hole ]
0 512K 512K 640K 640K 644K 644K 1M
This can be fixed by serializing memory mapped writes with fsync, and there
are two ways to do it:
1) Make a fsync lock the entire file range, from 0 to (u64)-1 / LLONG_MAX
in the inode's io tree. This prevents the race but also blocks any reads
during the duration of the fsync, which has a negative impact for many
common workloads;
2) Make an fsync write lock the i_mmap_lock semaphore in the inode. This
semaphore was recently added by Josef's patch set:
btrfs: add a i_mmap_lock to our inode
btrfs: cleanup inode_lock/inode_unlock uses
btrfs: exclude mmaps while doing remap
btrfs: exclude mmap from happening during all fallocate operations
and is used to solve races between memory mapped writes and
clone/dedupe/fallocate. This also makes us have the same behaviour we
have regarding other writes (buffered and direct IO) and fsync - block
them while the inode logging is in progress.
This change uses the second approach due to the performance impact of the
first one.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There's a small window where a deadlock can happen between fallocate and
mmap. This is described in detail by Filipe:
"""
When doing a fallocate operation we lock the inode, flush delalloc within
the target range, wait for any ordered extents to complete and then lock
the file range. Before we lock the range and after we flush delalloc,
there is a time window where another task can come in and do a memory
mapped write for a page within the fallocate range.
This means that after fallocate locks the range, there can be a dirty page
in the range. More often than not, this does not cause any problem.
The exception is when we are low on available metadata space, because an
fallocate operation needs to start a transaction while holding the file
range locked, either through btrfs_prealloc_file_range() or through the
call to btrfs_fallocate_update_isize(). If that's the case, we can end up
in a deadlock. The following list of steps explains how that happens:
1) A fallocate operation starts, locks the inode, flushes delalloc in the
range and waits for ordered extents in the range to complete;
2) Before the fallocate task locks the file range, another task does a
memory mapped write for a page in the fallocate target range. This is
possible since memory mapped writes do not (and can not) lock the
inode;
3) The fallocate task locks the file range. At this point there is one
dirty page in the range (due to the memory mapped write);
4) When the fallocate task attempts to start a transaction, it blocks when
attempting to reserve metadata space, since we are low on available
metadata space. Before blocking (wait on its reservation ticket), it
starts the async reclaim task (if not running already);
5) The async reclaim task is not able to release space through any other
means, so it decides to flush delalloc for inodes with dirty pages.
It finds that the inode used in the fallocate operation has a dirty
page and therefore queues a job (fs_info->flush_workers workqueue) to
flush delalloc for that inode and waits on that job to complete;
6) The flush job blocks when attempting to lock the file range because
it is currently locked by the fallocate task;
7) The fallocate task keeps waiting for its metadata reservation, waiting
for a wakeup on its reservation ticket. The async reclaim task is
waiting on the flush job, which in turn is waiting for locking the file
range that is currently locked by the fallocate task. So unless some
other task is able to release enough metadata space, for example an
ordered extent for some other inode completes, we end up in a deadlock
between all these tasks.
When this happens stack traces like the following show up in dmesg/syslog:
INFO: task kworker/u16:11:1810830 blocked for more than 120 seconds.
Tainted: G B W 5.10.0-rc4-btrfs-next-73 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:11 state:D stack: 0 pid:1810830 ppid: 2 flags:0x00004000
Workqueue: btrfs-flush_delalloc btrfs_work_helper [btrfs]
Call Trace:
__schedule+0x5d1/0xcf0
schedule+0x45/0xe0
lock_extent_bits+0x1e6/0x2d0 [btrfs]
? finish_wait+0x90/0x90
btrfs_invalidatepage+0x32c/0x390 [btrfs]
? __mod_memcg_state+0x8e/0x160
__extent_writepage+0x2d4/0x400 [btrfs]
extent_write_cache_pages+0x2b2/0x500 [btrfs]
? lock_release+0x20e/0x4c0
? trace_hardirqs_on+0x1b/0xf0
extent_writepages+0x43/0x90 [btrfs]
? lock_acquire+0x1a3/0x490
do_writepages+0x43/0xe0
? __filemap_fdatawrite_range+0xa4/0x100
__filemap_fdatawrite_range+0xc5/0x100
btrfs_run_delalloc_work+0x17/0x40 [btrfs]
btrfs_work_helper+0xf1/0x600 [btrfs]
process_one_work+0x24e/0x5e0
worker_thread+0x50/0x3b0
? process_one_work+0x5e0/0x5e0
kthread+0x153/0x170
? kthread_mod_delayed_work+0xc0/0xc0
ret_from_fork+0x22/0x30
INFO: task kworker/u16:1:2426217 blocked for more than 120 seconds.
Tainted: G B W 5.10.0-rc4-btrfs-next-73 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:1 state:D stack: 0 pid:2426217 ppid: 2 flags:0x00004000
Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
Call Trace:
__schedule+0x5d1/0xcf0
? kvm_clock_read+0x14/0x30
? wait_for_completion+0x81/0x110
schedule+0x45/0xe0
schedule_timeout+0x30c/0x580
? _raw_spin_unlock_irqrestore+0x3c/0x60
? lock_acquire+0x1a3/0x490
? try_to_wake_up+0x7a/0xa20
? lock_release+0x20e/0x4c0
? lock_acquired+0x199/0x490
? wait_for_completion+0x81/0x110
wait_for_completion+0xab/0x110
start_delalloc_inodes+0x2af/0x390 [btrfs]
btrfs_start_delalloc_roots+0x12d/0x250 [btrfs]
flush_space+0x24f/0x660 [btrfs]
btrfs_async_reclaim_metadata_space+0x1bb/0x480 [btrfs]
process_one_work+0x24e/0x5e0
worker_thread+0x20f/0x3b0
? process_one_work+0x5e0/0x5e0
kthread+0x153/0x170
? kthread_mod_delayed_work+0xc0/0xc0
ret_from_fork+0x22/0x30
(...)
several tasks waiting for the inode lock held by the fallocate task below
(...)
RIP: 0033:0x7f61efe73fff
Code: Unable to access opcode bytes at RIP 0x7f61efe73fd5.
RSP: 002b:00007ffc3371bbe8 EFLAGS: 00000202 ORIG_RAX: 000000000000013c
RAX: ffffffffffffffda RBX: 00007ffc3371bea0 RCX: 00007f61efe73fff
RDX: 00000000ffffff9c RSI: 0000560fbd5d90a0 RDI: 00000000ffffff9c
RBP: 00007ffc3371beb0 R08: 0000000000000001 R09: 0000000000000003
R10: 0000560fbd5d7ad0 R11: 0000000000000202 R12: 0000000000000001
R13: 000000000000005e R14: 00007ffc3371bea0 R15: 00007ffc3371beb0
task:fdm-stress state:D stack: 0 pid:2508243 ppid:2508153 flags:0x00000000
Call Trace:
__schedule+0x5d1/0xcf0
? _raw_spin_unlock_irqrestore+0x3c/0x60
schedule+0x45/0xe0
__reserve_bytes+0x4a4/0xb10 [btrfs]
? finish_wait+0x90/0x90
btrfs_reserve_metadata_bytes+0x29/0x190 [btrfs]
btrfs_block_rsv_add+0x1f/0x50 [btrfs]
start_transaction+0x2d1/0x760 [btrfs]
btrfs_replace_file_extents+0x120/0x930 [btrfs]
? btrfs_fallocate+0xdcf/0x1260 [btrfs]
btrfs_fallocate+0xdfb/0x1260 [btrfs]
? filename_lookup+0xf1/0x180
vfs_fallocate+0x14f/0x440
ioctl_preallocate+0x92/0xc0
do_vfs_ioctl+0x66b/0x750
? __do_sys_newfstat+0x53/0x60
__x64_sys_ioctl+0x62/0xb0
do_syscall_64+0x33/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
"""
Fix this by disallowing mmaps from happening while we're doing any of
the fallocate operations on this inode.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
A few places we intermix btrfs_inode_lock with a inode_unlock, and some
places we just use inode_lock/inode_unlock instead of btrfs_inode_lock.
None of these places are using this incorrectly, but as we adjust some
of these callers it would be nice to keep everything consistent, so
convert everybody to use btrfs_inode_lock/btrfs_inode_unlock.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=tlU3
-----END PGP SIGNATURE-----
Merge tag 'for-5.12-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"More regression fixes and stabilization.
Regressions:
- zoned mode
- count zone sizes in wider int types
- fix space accounting for read-only block groups
- subpage: fix page tail zeroing
Fixes:
- fix spurious warning when remounting with free space tree
- fix warning when creating a directory with smack enabled
- ioctl checks for qgroup inheritance when creating a snapshot
- qgroup
- fix missing unlock on error path in zero range
- fix amount of released reservation on error
- fix flushing from unsafe context with open transaction,
potentially deadlocking
- minor build warning fixes"
* tag 'for-5.12-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: do not account freed region of read-only block group as zone_unusable
btrfs: zoned: use sector_t for zone sectors
btrfs: subpage: fix the false data csum mismatch error
btrfs: fix warning when creating a directory with smack enabled
btrfs: don't flush from btrfs_delayed_inode_reserve_metadata
btrfs: export and rename qgroup_reserve_meta
btrfs: free correct amount of space in btrfs_delayed_inode_reserve_metadata
btrfs: fix spurious free_space_tree remount warning
btrfs: validate qgroup inherit for SNAP_CREATE_V2 ioctl
btrfs: unlock extents in btrfs_zero_range in case of quota reservation errors
btrfs: ref-verify: use 'inline void' keyword ordering
If btrfs_qgroup_reserve_data returns an error (i.e quota limit reached)
the handling logic directly goes to the 'out' label without first
unlocking the extent range between lockstart, lockend. This results in
deadlocks as other processes try to lock the same extent.
Fixes: a7f8b1c2ac ("btrfs: file: reserve qgroup space after the hole punch range is locked")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Rename generic_file_buffered_read to match the naming of filemap_fault,
also update the written parameter to a more descriptive name and improve
the kerneldoc comment.
Link: https://lkml.kernel.org/r/20210122160140.223228-18-willy@infradead.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Adjust the final parameter of iomap_dio_rw.
- Add a new flag to request that iomap directio writes return EAGAIN if
the write is not a pure overwrite within EOF; this will be used to
reduce lock contention with unaligned direct writes on XFS.
- Amend XFS' directio code to eliminate exclusive locking for unaligned
direct writes if the circumstances permit
-----BEGIN PGP SIGNATURE-----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=AR07
-----END PGP SIGNATURE-----
Merge tag 'iomap-5.12-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull iomap updates from Darrick Wong:
"The big change in this cycle is some new code to make it possible for
XFS to try unaligned directio overwrites without taking locks. If the
block is fully written and within EOF (i.e. doesn't require any
further fs intervention) then we can let the unlocked write proceed.
If not, we fall back to synchronizing direct writes.
Summary:
- Adjust the final parameter of iomap_dio_rw.
- Add a new flag to request that iomap directio writes return EAGAIN
if the write is not a pure overwrite within EOF; this will be used
to reduce lock contention with unaligned direct writes on XFS.
- Amend XFS' directio code to eliminate exclusive locking for
unaligned direct writes if the circumstances permit"
* tag 'iomap-5.12-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: reduce exclusive locking on unaligned dio
xfs: split the unaligned DIO write code out
xfs: improve the reflink_bounce_dio_write tracepoint
xfs: simplify the read/write tracepoints
xfs: remove the buffered I/O fallback assert
xfs: cleanup the read/write helper naming
xfs: make xfs_file_aio_write_checks IOCB_NOWAIT-aware
xfs: factor out a xfs_ilock_iocb helper
iomap: add a IOMAP_DIO_OVERWRITE_ONLY flag
iomap: pass a flags argument to iomap_dio_rw
iomap: rename the flags variable in __iomap_dio_rw
Enable zone append writing for zoned mode. When using zone append, a
bio is issued to the start of a target zone and the device decides to
place it inside the zone. Upon completion the device reports the actual
written position back to the host.
Three parts are necessary to enable zone append mode. First, modify the
bio to use REQ_OP_ZONE_APPEND in btrfs_submit_bio_hook() and adjust the
bi_sector to point the beginning of the zone.
Second, record the returned physical address (and disk/partno) to the
ordered extent in end_bio_extent_writepage() after the bio has been
completed. We cannot resolve the physical address to the logical address
because we can neither take locks nor allocate a buffer in this end_bio
context. So, we need to record the physical address to resolve it later
in btrfs_finish_ordered_io().
And finally, rewrite the logical addresses of the extent mapping and
checksum data according to the physical address using btrfs_rmap_block.
If the returned address matches the originally allocated address, we can
skip this rewriting process.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
To support subpage sector size, data also need extra info to make sure
which sectors in a page are uptodate/dirty/...
This patch will make pages for data inodes get btrfs_subpage structure
attached, and detached when the page is freed.
This patch also slightly changes the timing when
set_page_extent_mapped() is called to make sure:
- We have page->mapping set
page->mapping->host is used to grab btrfs_fs_info, thus we can only
call this function after page is mapped to an inode.
One call site attaches pages to inode manually, thus we have to modify
the timing of set_page_extent_mapped() a bit.
- As soon as possible, before other operations
Since memory allocation can fail, we have to do extra error handling.
Calling set_page_extent_mapped() as soon as possible can simply the
error handling for several call sites.
The idea is pretty much the same as iomap_page, but with more bitmaps
for btrfs specific cases.
Currently the plan is to switch iomap if iomap can provide sector
aligned write back (only write back dirty sectors, but not the full
page, data balance require this feature).
So we will stick to btrfs specific bitmap for now.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Often an fsync needs to fallback to a transaction commit for several
reasons (to ensure consistency after a power failure, a new block group
was allocated or a temporary error such as ENOMEM or ENOSPC happened).
In that case the log is marked as needing a full commit and any concurrent
tasks attempting to log inodes or commit the log will also fallback to the
transaction commit. When this happens they all wait for the task that first
started the transaction commit to finish the transaction commit - however
they wait until the full transaction commit happens, which is not needed,
as they only need to wait for the superblocks to be persisted and not for
unpinning all the extents pinned during the transaction's lifetime, which
even for short lived transactions can be a few thousand and take some
significant amount of time to complete - for dbench workloads I have
observed up to 4~5 milliseconds of time spent unpinning extents in the
worst cases, and the number of pinned extents was between 2 to 3 thousand.
So allow fsync tasks to skip waiting for the unpinning of extents when
they call btrfs_commit_transaction() and they were not the task that
started the transaction commit (that one has to do it, the alternative
would be to offload the transaction commit to another task so that it
could avoid waiting for the extent unpinning or offload the extent
unpinning to another task).
This patch is part of a patchset comprised of the following patches:
btrfs: remove unnecessary directory inode item update when deleting dir entry
btrfs: stop setting nbytes when filling inode item for logging
btrfs: avoid logging new ancestor inodes when logging new inode
btrfs: skip logging directories already logged when logging all parents
btrfs: skip logging inodes already logged when logging new entries
btrfs: remove unnecessary check_parent_dirs_for_sync()
btrfs: make concurrent fsyncs wait less when waiting for a transaction commit
After applying the entire patchset, dbench shows improvements in respect
to throughput and latency. The script used to measure it is the following:
$ cat dbench-test.sh
#!/bin/bash
DEV=/dev/sdk
MNT=/mnt/sdk
MOUNT_OPTIONS="-o ssd"
MKFS_OPTIONS="-m single -d single"
echo "performance" | tee /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
umount $DEV &> /dev/null
mkfs.btrfs -f $MKFS_OPTIONS $DEV
mount $MOUNT_OPTIONS $DEV $MNT
dbench -D $MNT -t 300 64
umount $MNT
The test was run on a physical machine with 12 cores (Intel corei7), 64G
of ram, using a NVMe device and a non-debug kernel configuration (Debian's
default configuration).
Before applying patchset, 32 clients:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 9627107 0.153 61.938
Close 7072076 0.001 3.175
Rename 407633 1.222 44.439
Unlink 1943895 0.658 44.440
Deltree 256 17.339 110.891
Mkdir 128 0.003 0.009
Qpathinfo 8725406 0.064 17.850
Qfileinfo 1529516 0.001 2.188
Qfsinfo 1599884 0.002 1.457
Sfileinfo 784200 0.005 3.562
Find 3373513 0.411 30.312
WriteX 4802132 0.053 29.054
ReadX 15089959 0.002 5.801
LockX 31344 0.002 0.425
UnlockX 31344 0.001 0.173
Flush 674724 5.952 341.830
Throughput 1008.02 MB/sec 32 clients 32 procs max_latency=341.833 ms
After applying patchset, 32 clients:
After patchset, with 32 clients:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 9931568 0.111 25.597
Close 7295730 0.001 2.171
Rename 420549 0.982 49.714
Unlink 2005366 0.497 39.015
Deltree 256 11.149 89.242
Mkdir 128 0.002 0.014
Qpathinfo 9001863 0.049 20.761
Qfileinfo 1577730 0.001 2.546
Qfsinfo 1650508 0.002 3.531
Sfileinfo 809031 0.005 5.846
Find 3480259 0.309 23.977
WriteX 4952505 0.043 41.283
ReadX 15568127 0.002 5.476
LockX 32338 0.002 0.978
UnlockX 32338 0.001 2.032
Flush 696017 7.485 228.835
Throughput 1049.91 MB/sec 32 clients 32 procs max_latency=228.847 ms
--> +4.1% throughput, -39.6% max latency
Before applying patchset, 64 clients:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 8956748 0.342 108.312
Close 6579660 0.001 3.823
Rename 379209 2.396 81.897
Unlink 1808625 1.108 131.148
Deltree 256 25.632 172.176
Mkdir 128 0.003 0.018
Qpathinfo 8117615 0.131 55.916
Qfileinfo 1423495 0.001 2.635
Qfsinfo 1488496 0.002 5.412
Sfileinfo 729472 0.007 8.643
Find 3138598 0.855 78.321
WriteX 4470783 0.102 79.442
ReadX 14038139 0.002 7.578
LockX 29158 0.002 0.844
UnlockX 29158 0.001 0.567
Flush 627746 14.168 506.151
Throughput 924.738 MB/sec 64 clients 64 procs max_latency=506.154 ms
After applying patchset, 64 clients:
Operation Count AvgLat MaxLat
----------------------------------------
NTCreateX 9069003 0.303 43.193
Close 6662328 0.001 3.888
Rename 383976 2.194 46.418
Unlink 1831080 1.022 43.873
Deltree 256 24.037 155.763
Mkdir 128 0.002 0.005
Qpathinfo 8219173 0.137 30.233
Qfileinfo 1441203 0.001 3.204
Qfsinfo 1507092 0.002 4.055
Sfileinfo 738775 0.006 5.431
Find 3177874 0.936 38.170
WriteX 4526152 0.084 39.518
ReadX 14213562 0.002 24.760
LockX 29522 0.002 1.221
UnlockX 29522 0.001 0.694
Flush 635652 14.358 422.039
Throughput 990.13 MB/sec 64 clients 64 procs max_latency=422.043 ms
--> +6.8% throughput, -18.1% max latency
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The original comment is from the initial merge, which has several
problems:
- No holes check any more
- No inline decision is made
Update the out-of-date comment with more correct one.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
First replace all inode instances with a pointer to btrfs_inode. This
removes multiple invocations of the BTRFS_I macro, subsequently remove
2 local variables as they are called only once and simply refer to
them directly.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pass a set of flags to iomap_dio_rw instead of the boolean
wait_for_completion argument. The IOMAP_DIO_FORCE_WAIT flag
replaces the wait_for_completion, but only needs to be passed
when the iocb isn't synchronous to start with to simplify the
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
[djwong: rework xfs_file.c so that we can push iomap changes separately]
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
fallocate() is implemented by reserving actual extent instead of
reservations. This can result in exposing the sequential write
constraint of host-managed zoned block devices to the application, which
would break the POSIX semantic for the fallocated file. To avoid this,
report fallocate() as not supported when in ZONED mode for now.
In the future, we may be able to implement "in-memory" fallocate() in
ZONED mode by utilizing space_info->bytes_may_use or similar, so this
returns EOPNOTSUPP.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are several occasions where we do not update the inode's number of
used bytes atomically, resulting in a concurrent stat(2) syscall to report
a value of used blocks that does not correspond to a valid value, that is,
a value that does not match neither what we had before the operation nor
what we get after the operation completes.
In extreme cases it can result in stat(2) reporting zero used blocks, which
can cause problems for some userspace tools where they can consider a file
with a non-zero size and zero used blocks as completely sparse and skip
reading data, as reported/discussed a long time ago in some threads like
the following:
https://lists.gnu.org/archive/html/bug-tar/2016-07/msg00001.html
The cases where this can happen are the following:
-> Case 1
If we do a write (buffered or direct IO) against a file region for which
there is already an allocated extent (or multiple extents), then we have a
short time window where we can report a number of used blocks to stat(2)
that does not take into account the file region being overwritten. This
short time window happens when completing the ordered extent(s).
This happens because when we drop the extents in the write range we
decrement the inode's number of bytes and later on when we insert the new
extent(s) we increment the number of bytes in the inode, resulting in a
short time window where a stat(2) syscall can get an incorrect number of
used blocks.
If we do writes that overwrite an entire file, then we have a short time
window where we report 0 used blocks to stat(2).
Example reproducer:
$ cat reproducer-1.sh
#!/bin/bash
MNT=/mnt/sdi
DEV=/dev/sdi
stat_loop()
{
trap "wait; exit" SIGTERM
local filepath=$1
local expected=$2
local got
while :; do
got=$(stat -c %b $filepath)
if [ $got -ne $expected ]; then
echo -n "ERROR: unexpected used blocks"
echo " (got: $got expected: $expected)"
fi
done
}
mkfs.btrfs -f $DEV > /dev/null
# mkfs.xfs -f $DEV > /dev/null
# mkfs.ext4 -F $DEV > /dev/null
# mkfs.f2fs -f $DEV > /dev/null
# mkfs.reiserfs -f $DEV > /dev/null
mount $DEV $MNT
xfs_io -f -s -c "pwrite -b 64K 0 64K" $MNT/foobar >/dev/null
expected=$(stat -c %b $MNT/foobar)
# Create a process to keep calling stat(2) on the file and see if the
# reported number of blocks used (disk space used) changes, it should
# not because we are not increasing the file size nor punching holes.
stat_loop $MNT/foobar $expected &
loop_pid=$!
for ((i = 0; i < 50000; i++)); do
xfs_io -s -c "pwrite -b 64K 0 64K" $MNT/foobar >/dev/null
done
kill $loop_pid &> /dev/null
wait
umount $DEV
$ ./reproducer-1.sh
ERROR: unexpected used blocks (got: 0 expected: 128)
ERROR: unexpected used blocks (got: 0 expected: 128)
(...)
Note that since this is a short time window where the race can happen, the
reproducer may not be able to always trigger the bug in one run, or it may
trigger it multiple times.
-> Case 2
If we do a buffered write against a file region that does not have any
allocated extents, like a hole or beyond EOF, then during ordered extent
completion we have a short time window where a concurrent stat(2) syscall
can report a number of used blocks that does not correspond to the value
before or after the write operation, a value that is actually larger than
the value after the write completes.
This happens because once we start a buffered write into an unallocated
file range we increment the inode's 'new_delalloc_bytes', to make sure
any stat(2) call gets a correct used blocks value before delalloc is
flushed and completes. However at ordered extent completion, after we
inserted the new extent, we increment the inode's number of bytes used
with the size of the new extent, and only later, when clearing the range
in the inode's iotree, we decrement the inode's 'new_delalloc_bytes'
counter with the size of the extent. So this results in a short time
window where a concurrent stat(2) syscall can report a number of used
blocks that accounts for the new extent twice.
Example reproducer:
$ cat reproducer-2.sh
#!/bin/bash
MNT=/mnt/sdi
DEV=/dev/sdi
stat_loop()
{
trap "wait; exit" SIGTERM
local filepath=$1
local expected=$2
local got
while :; do
got=$(stat -c %b $filepath)
if [ $got -ne $expected ]; then
echo -n "ERROR: unexpected used blocks"
echo " (got: $got expected: $expected)"
fi
done
}
mkfs.btrfs -f $DEV > /dev/null
# mkfs.xfs -f $DEV > /dev/null
# mkfs.ext4 -F $DEV > /dev/null
# mkfs.f2fs -f $DEV > /dev/null
# mkfs.reiserfs -f $DEV > /dev/null
mount $DEV $MNT
touch $MNT/foobar
write_size=$((64 * 1024))
for ((i = 0; i < 16384; i++)); do
offset=$(($i * $write_size))
xfs_io -c "pwrite -S 0xab $offset $write_size" $MNT/foobar >/dev/null
blocks_used=$(stat -c %b $MNT/foobar)
# Fsync the file to trigger writeback and keep calling stat(2) on it
# to see if the number of blocks used changes.
stat_loop $MNT/foobar $blocks_used &
loop_pid=$!
xfs_io -c "fsync" $MNT/foobar
kill $loop_pid &> /dev/null
wait $loop_pid
done
umount $DEV
$ ./reproducer-2.sh
ERROR: unexpected used blocks (got: 265472 expected: 265344)
ERROR: unexpected used blocks (got: 284032 expected: 283904)
(...)
Note that since this is a short time window where the race can happen, the
reproducer may not be able to always trigger the bug in one run, or it may
trigger it multiple times.
-> Case 3
Another case where such problems happen is during other operations that
replace extents in a file range with other extents. Those operations are
extent cloning, deduplication and fallocate's zero range operation.
The cause of the problem is similar to the first case. When we drop the
extents from a range, we decrement the inode's number of bytes, and later
on, after inserting the new extents we increment it. Since this is not
done atomically, a concurrent stat(2) call can see and return a number of
used blocks that is smaller than it should be, does not match the number
of used blocks before or after the clone/deduplication/zero operation.
Like for the first case, when doing a clone, deduplication or zero range
operation against an entire file, we end up having a time window where we
can report 0 used blocks to a stat(2) call.
Example reproducer:
$ cat reproducer-3.sh
#!/bin/bash
MNT=/mnt/sdi
DEV=/dev/sdi
mkfs.btrfs -f $DEV > /dev/null
# mkfs.xfs -f -m reflink=1 $DEV > /dev/null
mount $DEV $MNT
extent_size=$((64 * 1024))
num_extents=16384
file_size=$(($extent_size * $num_extents))
# File foo has many small extents.
xfs_io -f -s -c "pwrite -S 0xab -b $extent_size 0 $file_size" $MNT/foo \
> /dev/null
# File bar has much less extents and has exactly the same data as foo.
xfs_io -f -c "pwrite -S 0xab 0 $file_size" $MNT/bar > /dev/null
expected=$(stat -c %b $MNT/foo)
# Now deduplicate bar into foo. While the deduplication is in progres,
# the number of used blocks/file size reported by stat should not change
xfs_io -c "dedupe $MNT/bar 0 0 $file_size" $MNT/foo > /dev/null &
dedupe_pid=$!
while [ -n "$(ps -p $dedupe_pid -o pid=)" ]; do
used=$(stat -c %b $MNT/foo)
if [ $used -ne $expected ]; then
echo "Unexpected blocks used: $used (expected: $expected)"
fi
done
umount $DEV
$ ./reproducer-3.sh
Unexpected blocks used: 2076800 (expected: 2097152)
Unexpected blocks used: 2097024 (expected: 2097152)
Unexpected blocks used: 2079872 (expected: 2097152)
(...)
Note that since this is a short time window where the race can happen, the
reproducer may not be able to always trigger the bug in one run, or it may
trigger it multiple times.
So fix this by:
1) Making btrfs_drop_extents() not decrement the VFS inode's number of
bytes, and instead return the number of bytes;
2) Making any code that drops extents and adds new extents update the
inode's number of bytes atomically, while holding the btrfs inode's
spinlock, which is also used by the stat(2) callback to get the inode's
number of bytes;
3) For ranges in the inode's iotree that are marked as 'delalloc new',
corresponding to previously unallocated ranges, increment the inode's
number of bytes when clearing the 'delalloc new' bit from the range,
in the same critical section that decrements the inode's
'new_delalloc_bytes' counter, delimited by the btrfs inode's spinlock.
An alternative would be to have btrfs_getattr() wait for any IO (ordered
extents in progress) and locking the whole range (0 to (u64)-1) while it
it computes the number of blocks used. But that would mean blocking
stat(2), which is a very used syscall and expected to be fast, waiting
for writes, clone/dedupe, fallocate, page reads, fiemap, etc.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are many arguments for __btrfs_drop_extents() and its wrapper
btrfs_drop_extents(), which makes it hard to add more arguments to it and
requires changing every caller. I have added a couple myself back in 2014
commit 1acae57b16 ("Btrfs: faster file extent item replace operations")
and therefore know firsthand that it is a bit cumbersome to add additional
arguments to these functions.
Since I will need to add more arguments in a subsequent bug fix, this
change is preparatory work and adds a data structure that holds all the
arguments, for both input and output, that are passed to this function,
with some comments in the structure's definition mentioning what each
field is and how it relates to other fields.
Callers of this function need only to zero out the content of the
structure and setup only the fields they need. This also removes the
need to have both __btrfs_drop_extents() and btrfs_drop_extents(), so
now we have a single function named btrfs_drop_extents() that takes a
pointer to this new data structure (struct btrfs_drop_extents_args).
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we're using a rw_semaphore we no longer need to indicate if a
lock is blocking or not, nor do we need to flip the entire path from
blocking to spinning. Remove these helpers and all the places they are
called.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana