This driver handles the variants pca9530-pca9533, so it chose the name
"pca953x". However, there is a gpio driver which decided on the same
name. As a result, those two can't be loaded at the same time. Add a
subsystem prefix to make the driver name unique. Device matching will not
suffer, because both are I2C drivers which match using a
i2c_device_id-table which is not altered.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pca953x family are only different in number of leds and register
layout Adding chipinfo to use driver with whole pca953x family Rename
driver to pca953x, but left files and platformflags named pca9532.
Tested with pca9530 and pca9533
Tested-by: Juergen Kilb <j.kilb@phytec.de>
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Acked-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Tested-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow unused leds on pca9532 to be used as gpio. The board I am working
on now has no less than 6 pca9532 chips. One chips is used for only leds,
one has 14 leds and 2 gpio and the rest of the chips are gpio only.
There is also one board in mainline which could use this capabilty;
arch/arm/mach-iop32x/n2100.c
232 { .type = PCA9532_TYPE_NONE }, /* power OFF gpio */
233 { .type = PCA9532_TYPE_NONE }, /* reset gpio */
This patch defines a new pin type, PCA9532_TYPE_GPIO, and registers a
gpiochip if any pin has this type set. The gpio will registers all chip
pins but will filter on gpio_request.
[randy.dunlap@oracle.com: fix build when GPIOLIB is not enabled]
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jan Weitzel <j.weitzel@phytec.de>
Cc: Juergen Kilb <j.kilb@phytec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Remove unneeded input_free_device() after input_unregister_device().
- Add pca9532_destroy_devices() function for destroy devices.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The leds-pca9532 driver doesn't, so there
is no point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Riku Voipio <riku.voipio@iki.fi>
Indent using tabs, not spaces.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This fixes the expression in the driver to do the correct thing,
not that I think anyone would send SND_* without EV_SND.
Thanks to Roel Kluin <roel.kluin@gmail.com> for noticing.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Apparently these might be called under atomic context,
and i2c operations may sleep. BUG found by
Ross Burton <ross@burtonini.com>
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
When the registration fails, we need to release the memory we allocated.
Also we need to save the error from led_classdev_register and propagate
it up, else we'll return success, even if we failed.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
NXP pca9532 is a LED dimmer/controller attached to i2c bus. It allows
attaching upto 16 leds which can either be on, off or dimmed and/or blinked
with the two PWM modulators available.
This driver is a "new-style" i2c driver that adheres to the driver model and
implements the led framework api. Since the leds connected to the driver are
platform specific, it is only useful when platform data is passed to the
driver to define what leds are connected to which pins.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Wolfram Sang