This is part of a patch series to add support for a new HCA. This patch
adds new fields to the header files.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes chip reset more robust and reduces lock contention
between user and kernel TID register updates.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Newer HCAs support MSI interrupts and also INTx interrupts. Fix the
code so that INTx can be reliably enabled if MSI interrupts are not
working.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Newer HCAs have a threshold counter to reduce the number of DMAs the
chip makes to update the PIO buffer availability status bits. This
patch enables the feature.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Whenever the LID is set, notify the HCA specific code so that the
appropriate HW registers can be updated. Also log the info on the
console at low priority.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds code to enable/disable the IBTA 1.2 heartbeat for testing
if the HCA supports it.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware-based recovery doesn't need any intervention, and in a few
cases we can get a bit confused about state and skip steps such as
turning off the link state LED when we consider recovery to be "down".
So ignore this transition, and either we recover in hardware, or we
transition to down, and will handle it then.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Newer HCAs have a HW option to write a sequence number to each receive
queue entry and avoid a separate DMA of the tail register to memory.
This patch adds support for these changes.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes some white space changes and minor non-functional
changes to more closely match the code in OFED-1.3.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch checks for old and new format writes to send a packet via the
diagnostic interface.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Raw comparison against jiffies will fail if jiffies wraps, although
since ipath currently only supports 64-bit architectures, this is rather
far-fetched. Still, it's better to use time_after_eq().
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a create_flags member to struct ib_qp_init_attr that will allow a
kernel verbs consumer to create a pass special flags when creating a QP.
Add a flag value for telling low-level drivers that a QP will be used
for IPoIB UD LSO. The create_flags member will also be useful for XRC
and ehca low-latency QP support.
Since no create_flags handling is implemented yet, add code to all
low-level drivers to return -EINVAL if create_flags is non-zero.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for reading newer card's EEPROMs while continuing to support
older EEPROMs.
Also, add support for the temperature sensor if present.
Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This reduces the latency for RC ACKs when a PIO buffer is available.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A fixed partitioning of send buffers is determined at driver load time
for user processes and kernel use. Since send buffers are a scarce
resource, it makes sense to allow the kernel to use the buffers if they
are not in use by a user process.
Also, eliminate code duplication for ipath_force_pio_avail_update().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link can be put in LINKDOWN_DISABLE state either locally or via a
MAD. However, the link-recovery code will take it out of that state as
a side-effect of attempts to clear SerDes/XGXS issues.
We add a flag to indicate "link is down on purpose, leave it alone."
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update the module author to the current email address.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In slave_or_pri_blk(), pci_write_config_byte() is used to write a
16-bit quantity to clear linkctrl CRC error bits. This is clearly a
bug and also causes the warning
drivers/infiniband/hw/ipath/ipath_iba6110.c: In function 'slave_or_pri_blk':
drivers/infiniband/hw/ipath/ipath_iba6110.c:849: warning: overflow in implicit constant conversion
Fix this by using pci_write_config_word() instead.
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The receive queue number of WRs and SGEs shouldn't be checked if a
SRQ is specified.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove useless comment about list removal since locks are held and
the code checks that the QP is on the list before removing it.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Workaround a QLE7140 problem that in rare cases causes flow control
problems after link recovery by forcing a link retrain after recovery.
A module parameter is provided to control the behavior in case it causes
problems.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds code to get/set portinfo to support multiple link speeds
and widths.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's a conflict between our need to quiesce PSM-based applications
to avoid HoL blocking when the IB link goes down and the apps' desire
to remain running so that their quiescence timout mechanism can keep
running.
The compromise is to STOP the processes for a fixed period of time and
then alternate between CONT and STOP until the link is again active.
If there are poor interactions with subnet manager configuration at a
given site, the interval can be adjusted via a module paramter.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't try to handle freeze mode HW errors if the driver is in diagnostic
mode since some tests can cause errors that shouldn't be processed.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The check for link up was incorrect, thus setting the LED display
inconsistently with the link state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error recovery code for updating the driver's cached status information
for which send buffers are busy or free wasn't updated for IBA7220.
It should be similar to the initialization code in enable_chip().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix byte order of value assigned to pioavailshadow. This bug was
detected by sparse endianness warnings.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable use of 4KB MTU. Since the driver uses more pinned memory for
receive buffers when the 4KB MTU is enabled, whether or not the fabric
supports that MTU, add a "mtu4096" module parameter that can be used to
limit the MTU to 2KB when it is known that 4KB MTUs can't be used
anyway.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code was checking if units are present, but not that present units
were usable (link up, etc.)
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modern I/O buses like PCIe and HT can be configured for multiple speeds
and widths. When an ipath HCA seems to have lower than expected
performance, it is very useful to be able to display what the driver
thinks the bus speed is.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes some constants chip-specific, and makes some related
changes to prepare for supporting another HCA.
Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recent sparse versions and kernel cleanups knock down the false positive
rate of the ipath driver code to a point where having it be sparse clean
is worthwhile. Here we fixup the sparse warnings. Some of these warnings
(and the impetus to run sparse again) are due to work by Roland Dreier.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix
drivers/infiniband/hw/ipath/ipath_init_chip.c:526:10: warning: symbol 'val' shadows an earlier one
drivers/infiniband/hw/ipath/ipath_init_chip.c:473:6: originally declared here
by giving the second val a different name.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Arthur Jones <arthur.jones@qlogic.com>
There's no reason for the third parameter of ipath_count_units() to be
a u32 *, so change it to be an int * instead. This fixes the sparse
warning:
drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: warning: incorrect type in argument 3 (different signedness)
drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: expected unsigned int [usertype] *maxportsp
drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: got int *<noident>
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reset the retry counter when we get a good RDMA_READ_RESPONSE_MIDDLE
packet. This fix will prevent the requester from reporting a retry
exceeded error too early.
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
A work completion entry could be placed on the wrong completion
queue when an RC QP is placed in the error state.
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the initialization of RC QPs, since we would rely on
the queue pair type (ibqp->qp_type) being set, but this field is only
initialized when we return from ipath_create_qp (it is initialized by
the user-level verbs library).
The fix is to not depend on this field to initialize the send and
the receive state of the RC QP.
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There can be a case where the requester's rnr retry counter
(s_rnr_retry) is less than the number of rnr retries allowed per QP
(s_rnr_retry_cnt). This can happen if the s_rnr_retry counter is being
decremented and an ipath_query_qp call is issued during that time frame.
The fix is to always return the number of rnr retries allowed per QP
instead of the requester's rnr counter.
Found by code review.
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Subnet manager SetPortinfo messages distingush between changing the link
state (DOWN, ARM, ACTIVE) and the link physical state (POLL, SLEEP,
DISABLED). These are somewhat independent commands and affect when link
width and speed changes take effect. Without this patch, a link DOWN
physical state NOP command was causing the link width and speed settings
to take effect which should only happen when the link physical state is
goes down (either by a SMP or some link physical error like link errors
exceeding the threshold).
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the increment of s_hdrwords into the existing if block that tests
if we're doing a send with immediate, to save one test of the opcode.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new mappings from port physical state (a HW register value) to the
IB SubnGet(PortInfo) port physical state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBA7220 uses a count-based triggering mechanism, and therefore
can't use the same bandwidth verification mechanism as older chips.
To support the 7220, allow enabling and disabling armlaunch errors on
application request. Minor robustness improvements as well.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up some unused header fields, minor related cleanup.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IBA7220 includes many more configurable IB settings. Getting/setting
these is now grouped into a pair of chip specific functions accessed via
function pointers. Provide sysfs access to these settings.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This adds the new (sometimes empty) chip-specific functions to the older
chips, and makes the initialization and related functions consistent across
all 3 chips.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This code has been unused for some time, but still had leftovers
from when it was used.
Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are a few places in the ipath driver where a variable is
re-declared within a block where it is already in scope. Most of these
extra declarations can simply be removed, since the variable from the
outer scope is used in a way so that it does not need to keep its
variable across the block with the re-declaration.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The original QHT7040 had significant performance issues so there was an
additional check in the driver for a newer serial number. Support for
the small quantities of that board shipped has been dropped, so this
patch removes the special checks to simplify the code.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different chips have different width interrupt status registers, so add
a flag and accessor function to decide which width register read to use.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 6110 had a bug that caused some registers to be swapped; it was
fixed for the 7220 (and didn't affect the 6120 because it had fewer
registers). This adds a flag and related code to handle that, and
includes some minor cleanups in the same area.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
The number of configured ports for the 7220 changes the number of eager
TIDs available per port, for all but port 0 (kernel port) which remains
constant, so add a field to give port0 count separate from the portdata
structure.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
User registers have different alignments on different chips (4KB on
older, 64KB on 7220). Allow mapping the user registers on kernels with
page sizes up to 64K.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Various hardware counters are exported via the ipath file system (since
it is binary data). The old file format was very dependent on the HW
offsets for these registers. Newer HCA chips can have different
counters at different offsets. This patch adds a level of indirection
to make the file format consistent across HCAs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for QLogic HCAs which have hardware performance sampling
registers for PortSamplesControl and PortSamplesResult MADs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch moves some arrays that were defined per-device to be
variables defined in the per context data structure, thus avoiding extra
kzalloc() calls.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In preparation for upcoming chips that have different values for
INFINIPATH_R_PORTENABLE_SHIFT, INFINIPATH_R_INTRAVAIL_SHIFT,
INFINIPATH_R_TAILUPD_SHIFT, and portcfg_shift, remove the shared
#defines and use device-specific variables instead.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
kreceive is now portdata * instead of devdata * and other kreceive
related cleanups....
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove an unused parameter and fix up the comment.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a couple of minor problems with RNR NAK handling:
- The insertion sort was causing extra delay when inserting ahead
vs. behind an existing entry on the list.
- A resend of a first packet of a message which is still not ready,
needs another RNR NAK (i.e., it was suppressed when it shouldn't).
- Also, the resend tasklet doesn't need to be woken up unless the
ACK/NAK actually indicates progress has been made.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add the work completion error code to the QP error debug output.
This makes it easier to determine the cause of the error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An internal code review found the comment here lacking -- update it with
more specifics of how and why the rmb() is there.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a code review, someone noticed the comments didn't match the code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The gen2_basic tests check for the errno value when a CQ is resized
smaller than the number of outstanding completions queue on the CQ.
This patch changes ib_ipath to return EINVAL which is what ib_mthca
returns and what gen2_basic expects.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code review pointed out that the locking around uses of ipath_sendctrl
and kr_sendctrl were, in several places, incorrect and/or inconsistent.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one point in time there was code to allow a user process to
wait for a send buffer if none were available. This feature was
never used and most of the code was removed. This removes
some missed unused code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Tested-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch is in response to reviewing a patch to the core MAD
processing which fixes loopback of directed route packets to/from user
level MAD agents. This change enables the core code to work for
ib_ipath by fixing the return code from the ipath process_mad method.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve interrupt handler cache footprint by noinline'ing error
functions that are rarely called.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 23b9c1ab ("Infiniband: make ipath driver use default driver
groups.") introduced a bug in the ipath driver where
ipath_device_create_group() fell through into the error path, even on
success, which meant that the sysfs groups it created would always get
removed right away. This made ipath_device_remove_group() hit the
BUG_ON() in sysfs_remove_group() when it tried to remove those groups a
second time.
Correct the return path so that the groups stick around until they are
supposed to be cleaned up.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the ipath driver use the new driver functions so that it does not
touch the sysfs portion of the driver structure.
We also remove the redundant symlink from the device back to the driver,
as it is already in the sysfs tree. Any userspace tools should be using
the standard symlink, not some driver specific one.
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Arthur Jones <arthur.jones@qlogic.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a small bug in ipath_ud_rcv()'s handling of UD messages
with immediate data. We need to test whether immediate data is
present and update the header size accordingly *before* testing the
packet size from the header against the actual received length.
Otherwise the wrong header size will be used and all messages with
immediate data will be dropped.
This bug keeps MVAPICH-UD and HP MPI from working at all on ipath devices.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error codes for ib_post_send(), ib_post_recv(), and ib_post_srq_recv()
were inconsistent. Use EINVAL for too many SGEs and ENOMEM for too many
WRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_modify_srq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the code which frees the partially allocated QP
resources if there was an error while creating the QP. In particular,
the QPN wasn't deallocated and the QP wasn't removed from the hash
table.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_resize_cq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an ACK is received, the QP is removed from the timeout list and
then if there are still pending send WQEs, the QP is put back on the
timeout list. It is possible that another post send has put the QP on
the timeout list thus, a check needs to be made before trying to do it
again or the list is corrupted.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Inside a function declared as
void foo(char bar[512])
the value of sizeof bar is the size of a pointer, not 512. So avoid
constructions like this by passing the size explicitly.
Also reduce the size of the buffer to 128 bytes (512 was overly generous).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The small eeprom that holds the GUID etc. contains a data-length, but if
the actual eeprom is new or has been erased, that byte will be 0xFF,
which is greater than the maximum physical length of the eeprom, and
more importantly greater than the length of the buffer we vmalloc'd.
Sanity-check the length to avoid the possbility of reading past end of
buffer.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a small window where a send work queue entry could be
overwritten by ib_post_send() because s_last is updated before the
entry is read.
This patch closes the window by acquiring the lock and updating
the last send work queue entry index after reading the wr_id.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixed to be the same as everywhere else. copy and then zero the page *
in the array first, and then pass the copy to the VM routines.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch removes some redundant checks when the SMA changes the link
state since the same checks are made in the lower level function that
sets the state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link state event calls were being generated when the SM told the SMA
to change link states. This works for IB_EVENT_PORT_ACTIVE but not if
the link goes down and stays down. The fix is to generate event calls
from the interrupt handler when the HW link state changes.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The General Purpose I/O pins can be configured to cause interrupts. At
the end of the interrupt code dealing with all known causes, a message
is output if any bits remain un-handled. Since this is a "can't happen"
scenario, it should only be triggered by bugs elsewhere. It is harmless,
and potentially beneficial, to limit the damage by masking any such
unexpected interrupts.
This patch adds disabling of interrupts from any pins that should
not have been allowed to interrupt, in addition to emitting a message.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a count of "active hours" maintained in EEPROM, to aid
troubleshooting. The definition of "active" is based on traffic
exceeding a threshold in any given 5-second polling interval. As
originally written, the check was inadvertently bypassed for chips whose
counters were 64-bits wide, and only applied to chips with 32-bit wide
counters.
This patch moves the test for amount of traffic "out" to a more common
location, rather than depending on a side-effect of the software
emulation of 64-bit counts on chips whose hardware is only 32-bits wide.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove all the OEM and bringup boards, and complain and fail
initialization if one is found. QHT7040 with GPIO rework (128ywwuuuu)
is OK, older 112ywwuuuu is no longer supported). The check that had been
added was failing both the 112 and 128 series.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A couple of chip bugs in the iba6110 and in the iba6120 are not in more
recent chips. This first bug swaps two of the pioavail register
locations. In the second bug, the chip can sometimes forget to dma the
pio avail register to memory. We indicate the presence of these bugs
with runtime flags and we indicate the presence of the flags by bumping
the SWMINOR.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iba6110 rev3 and earlier had a chip bug where the chip could overrun the
recv header queue. rev4 fixed this chip bug so userspace no longer needs
to workaround it. Now we only set the workaround flag for older chip
versions.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_poll() suffered from a couple subtle bugs. Under the right
conditions we could leave recv interrupts enabled on an ipath user
context on close, thereby taking potentially unwanted interrupts on the
next open -- this is fixed by unconditionally turning off recv
interrupts on close. Also, we now use counters rather than set/clear
bits which allows us to make sure we catch all interrupts at the cost of
changing the semantics slightly (it's now give me all events since the
last time I called poll() rather than give me all events since I called
_this_ poll routine). We also added some memory barriers which may help
ensure we get all notifications in a timely manner.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The LMC value was being saved by the SMA in two places. This patch
cleans it up so only one copy is kept.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds the ability to set the LMC via a sysfs file as if the SM
sent a SubnSet(PortInfo) MAD. It is useful for debugging when no SM is
running.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to add an entry to the completion queue stored the QPN which is
needed for the user level verbs view of the completion queue entry but
the kernel struct ib_wc contains a pointer to the QP instead of a QPN.
When the kernel polled for a completion queue entry, the QPN was lookup
up and the QP pointer recovered. This patch stores the CQE differently
based on whether the CQ is a kernel CQ or a user CQ thus avoiding the
QPN to QP lookup overhead.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch implements the IB_EVENT_QP_LAST_WQE_REACHED event which is
needed by ib_ipoib to destroy the QP when used in connected mode.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Follow the IB spec. (C10-96) for post send which states that a flushed
completion event should be generated for work requests posted when a QP
is in the error state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch removes some redundant initialization code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In an earlier change, the amount of data read from the flash was
mistakenly limited to the size known to the current driver. This causes
problems when the length is increased, and written with the new longer
version; the checksum would fail because not enough data was read.
Always read the full 128 byte length to prevent this.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a bug in the receive processing for UC RDMA WRITE with
immediate which caused the last packet to be dropped.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a comment change, only, correcting the comment to match the
implemented workaround, rather than the original workaround, and
clarifying why it's needed.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipathfs file system is used to export binary data verses ASCII data
such as through /sys. This patch removes some unneeded files since the
data is available through other /sys files.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There have been a number of issues where host bandwidth via HT or PCIe
to the InfiniPath chip has been limited in some fashion (BIOS,
configuration, etc.), resulting in user confusion. This check gives a
clear warning that something is wrong and needs to be resolved.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to post UD sends tried to process work requests at the time
ib_post_send() is called without using a WQE queue. This was fine as
long as HW resources were available for sending a packet. This patch
changes UD to be handled more like RC and UC and shares more code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different processors have different ordering restrictions for write
combining. By taking advantage of this, we can eliminate some write
barriers when writing to the send buffers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On iba6110 rev4, support for three more IB counters were added. The
LocalLinkIntegrityError counter, the ExcessiveBufferOverrunErrors
counter and support for error counting of flow control packets on an
invalid VL. These counters trigger GPIO interrupts and the sw keeps
track of the counts. Since we also use GPIO interrupts to signal packet
reception, we need to turn off the fast interrupts, or we risk losing a
GPIO interrupt.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: Workaround problem of errormask register being overwritten
IB/ipath: Fix some issues with buffer cancel and sendctrl register update
IB/ipath: Use faster put_tid_2 routine after initialization
IB/ipath: Remove unsafe fastrcvint code from interrupt handler
IB/ehca: Move extern declarations from .c files to .h files
IB/mlx4: Whitespace fix
IB/ehca: Fix include order to better match kernel style
mlx4_core: Remove kfree() in mlx4_mr_alloc() error flow
RDMA/amso1100: Initialize the wait_queue_head_t in the c2_qp structure
On some system hardware, we are seeing moderately common cases of the
chip errormask register being overwritten due to a chip bug in iba6120
that is triggered by a vendor-specific PCIe broadcast message. This
patch merely checks periodically, and corrects it if needed (the
overwrite can cause us to not get error and hardware error
interrupts). Also, make dd->ipath_errormask the one, true canonical
source for kr_errormask, and remove references to ipath_ignorederrs as
it is currently unused.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There was confused use of INFINIPATH_S_PIOBUFAVAILUPD (value) and
IPATH_S_PIOBUFAVAILUPD (bit position). Also, some callers of
ipath_cancel_sends() need kr_sendctrl restored, and some want to do it
later.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one time the ipath_minrev field was initialized prior to the
ipath_init_iba6120_funcs call, but that is no longer the case, so the
slower put_tid routine was always being used.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The fastrcvint code's purpose was to avoid reading the interrupt
status if kernel packets were in the receive queue (to reduce
overhead). Because intstatus was not read, we could miss the error
interrupt bit indicating freeze mode, since it only delivers a single
interrupt, even if still pending after intclear is written.
This patch removes that unsafe optimization.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipath_layer.[ch] code was an attempt to provide a single interface
for the ipath verbs and ipath_ether code to use. As verbs
functionality increased, the layer's functionality became insufficient
and the verbs code broke away to interface directly to the driver.
The failed attempt to get ipath_ether upstream was the final nail in
the coffin and now it sits quietly in a dark kernel.org corner waiting
for someone to notice the smell and send it along to it's final
resting place. Roland Dreier was that someone -- this patch expands
on his work...
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make some functions that are only used in a single .c file static. In
addition to being a cleanup, this shrinks the generated code. On x86_64:
add/remove: 1/3 grow/shrink: 2/1 up/down: 4777/-4956 (-179)
function old new delta
handle_errors - 3994 +3994
__verbs_timer 42 710 +668
ipath_do_ruc_send 2131 2246 +115
ipath_no_bufs_available 136 - -136
ipath_disarm_senderrbufs 639 - -639
ipath_ib_timer 658 - -658
ipath_intr 5878 2355 -3523
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (76 commits)
IB: Update MAINTAINERS with Hal's new email address
IB/mlx4: Implement query SRQ
IB/mlx4: Implement query QP
IB/cm: Send no match if a SIDR REQ does not match a listen
IB/cm: Fix handling of duplicate SIDR REQs
IB/cm: cm_msgs.h should include ib_cm.h
IB/cm: Include HCA ACK delay in local ACK timeout
IB/cm: Use spin_lock_irq() instead of spin_lock_irqsave() when possible
IB/sa: Make sure SA queries use default P_Key
IPoIB: Recycle loopback skbs instead of freeing and reallocating
IB/mthca: Replace memset(<addr>, 0, PAGE_SIZE) with clear_page(<addr>)
IPoIB/cm: Fix warning if IPV6 is not enabled
IB/core: Take sizeof the correct pointer when calling kmalloc()
IB/ehca: Improve latency by unlocking after triggering the hardware
IB/ehca: Notify consumers of LID/PKEY/SM changes after nondisruptive events
IB/ehca: Return QP pointer in poll_cq()
IB/ehca: Change idr spinlocks into rwlocks
IB/ehca: Refactor sync between completions and destroy_cq using atomic_t
IB/ehca: Lock renaming, static initializers
IB/ehca: Report RDMA atomic attributes in query_qp()
...
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return the PortGUID of the correct port when responding to a NodeInfo
query. Returning the SystemImageGUID causes issues when there are
multiple HCAs in a single system.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The changeset 3859e39d ("IB/ipath: Support larger IB_QP_MAX_DEST_RD_ATOMIC
and IB_QP_MAX_QP_RD_ATOMIC") added support for larger RD_ATOMIC values,
but it failed to take out the stricter checks that were before these and
hence had no effect. This patch takes out the bogus checks....
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All too often, interrupts do not get enabled for our card due to BIOS
misconfiguration and other issues. This patch checks for that
condition on startup and warns the user. This patch is based on work
(check LID availability) by Robert Walsh.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The default calculation for the number of send buffers to allocate to
the kernel was too high for the PCIe version of the chip thus leaving
fewer than desired send buffers for user MPI applications.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We are more careful to be sure that we don't lose information about
changes that occurred while we were in freeze mode, when the chip will
not notify us, and try to avoid false error interrupts while doing
cleanup. Put all of this logic in a new function ipath_clear_freeze().
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a barrier to make sure the CPU doesn't reorder writes to memory,
since user programs can be polling on the head index update and the
entry should be written before that.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that it's June, it's about time to update
the copyright notices of files that have changed.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix ipath_poll and enhance it so we can poll for urgent packets or
regular packets and receive notifications of when a header queue
overflows.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB specification ch. 9.9.3 table 58 says that a QP which isn't set
up for the operation should return a NAK invalid request.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During compliance testing and when debugging some interconnect issues,
it is very useful to be able to send malformed packets, without having
the device signal them as malformed (drop, or terminate with EBP). The
hardware supports this, but the driver "diagnostic packet" interface
did not.
Extend capability to send specific malformed packets for testing.
Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Previously the driver and userspace code handled the case of 1 subport
somewhat inconsistently. The new interpretation of this situation is
that if one subport is requested, the driver turns on the subport
mechanism and arranges for the port to be "shared" by one process. In
normal use the userspace library does not use this configuration and
instead arranges for the port not to be shared at all. This
particular idiom can be useful for testing purposes.
Signed-off-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When subports are required to run a program, this patch checks that
the driver and the userspace library have compatible subport
implementations. This is achieved through checks on the swminor
version field built into the driver and userspace library. Bad
combinations are reported through syslog and result in an error when
opening the port.
Signed-off-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A duplicate RDMA read request can fool the responder into NAKing a new
RDMA read request because the responder wasn't keeping track of
whether the queue of RDMA read requests had been sent at least once.
For example, requester sends 4 2K byte RDMA read requests, times out,
and resends the first, then sees the 4 responses, then sends a 5th
RDMA read or atomic operation. The responder sees the 4 requests,
sends 4 responses, sees the resent 1st request, rewinds the queue,
then sees the 5th request but thinks the queue is full and that the
requester is invalidly sending a 5th new request.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to copy data from the receive queue buffers to the IB SGEs
doesn't check the SGE length, only the memory region/page length when
copying data. This could overwrite parts of the user's memory that
were not intended to be written. It can only happen if multiple SGEs
are used to describe a receive buffer which almost never happens in
practice.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The send function is called when posting new send work requests.
There is no point in trying to send a packet if the QP is already
waiting for a HW send buffer so don't clear the busy bit until the
buffer available interrupt happens.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A RDMA read response or atomic response can ACK earlier sends and RDMA
writes. In this case, the wrong work request pointer was being used
to store the read first response or atomic result. Also, if a RDMA
read request is retried, the code to compute which request to resend
was incorrect.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This centralizes the use of the abort functionality, removes the
unneeded buffer cancel (abort does the same thing), sets up to ignore
launch errors after abort, same as cancel. We need abort on exit from
freeze mode to avoid having buffers stuck in the busy state, if a user
process happened to complete the send while we were in freeze mode
doing the recovery.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The values passed have never been right for iba 6120 chips, but just
happened to work. We needed to select the right buffer offset in the
chip (both are in same register), and the total length was wrong also,
but was covered by the rounding up.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define pkt rcvd 'type' in a way consistent with HW spec and chips.
The hardware considers received packets of type 0 to be expected, and
type 1 to be eager. The driver was calling the ipath_f_put_tid
functions using a variable called 'type' set to 0 for eager and to 1
for expected packets. Worse, the iba6110 and iba6120 drivers used
those values inconsistently. This was quite confusing. Now
everything is consistent with the hardware.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to chapter 17.2.8.1.1, QPs start in the migrated state and
should send packets with the M bit set in the BTH.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a minor bug where the wrong QP was checked for a send
work request that should wait for an RNR timeout.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a bug introduced when moving some code around for
readability.
Setting the wqe pointer at the end of the function is a NOP since it
isn't used. Move it back to where it is used.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In ipath_query_device(), some of the struct ib_device_attr fields were
not being initialized.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Although our chip supports 4K MTUs, our driver doesn't yet support
this feature, so limit the maximum MTU to 2K until we get support for
4K MTUs implemented.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recognize IBA 6110 Revision 4: same feature set, etc. as earlier revisions.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We currently track various errors, now we enhance that capability by
logging some of them to EEPROM. We also now log a cumulative "active"
time defined by traffic though the InfiniPath HCA beyond the normal SM
traffic.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPATH_RUNTIME_PBC_REWRITE and the IPATH_RUNTIME_LOOSE_DMA_ALIGN
flags were not ever implemented correctly and did not turn out to be
necessary. Remove the last vestiges of these flags but mark the spot
with a comment to remind us to not reuse these flags in the interest
of binary compatibility. The INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR
bit was also not found to be useful, so it was dropped in the cleanup
as well.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new LED blinking interface adds more contention for the
unprotected GPIO pins that were already shared, though not commonly at
the same time. We add locks to the accesses to these pins so that
Read-Modify-Write is now safe. Some of these locks are added at
interrupt context, so we shadow the registers which drive and inspect
these pins to avoid the mmio read/writes. This mitigates the effects
of the locks and hastens us through the interrupt.
Add locking and always use shadows for registers controlling GPIO pins
(ExtCtrl and GPIOout). The use of shadows implies doing less I/O,
which can make I2C operation too fast on some platforms. An explicit
udelay(1) in SCL manipulation fixes that.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we want to find an InfiniPath HCA in a rack of nodes, it is often
expeditious to blink the status LEDs via a userspace /sys file.
A write-only led_override "file" is published per device. Writes to
this file are interpreted as (string form) numbers, and the resulting
value sent to ipath_set_led_override(). The upper eight bits are
interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom
two 4-bit values are alternately (D0..3, then D4..7) used by the
board-specific LED-setting function to override the normal state.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Lockdep found the following potential deadlock between mcast_lock and
n_mcast_grps_lock: mcast_lock is taken from both interrupt context and
process context, so spin_lock_irqsave() must be used to take it.
n_mcast_grps_lock is only taken from process context, so at first it
seems safe to take it with plain spin_lock(); however, it also nests
inside mcast_lock, and hence we could deadlock:
cpu A cpu B
ipath_mcast_add():
spin_lock_irq(&mcast_lock);
ipath_mcast_detach():
spin_lock(&n_mcast_grps_lock);
<enter interrupt>
ipath_mcast_find():
spin_lock_irqsave(&mcast_lock);
spin_lock(&n_mcast_grps_lock);
Fix this by using spin_lock_irq() to take n_mcast_grps_lock.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Once upon a time, GPIO interrupts were rare. But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception. This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips. Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on. An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.
Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export ib_umem_get()/ib_umem_release() and put low-level drivers in
control of when to call ib_umem_get() to pin and DMA map userspace,
rather than always calling it in ib_uverbs_reg_mr() before calling the
low-level driver's reg_user_mr method.
Also move these functions to be in the ib_core module instead of
ib_uverbs, so that driver modules using them do not depend on
ib_uverbs.
This has a number of advantages:
- It is better design from the standpoint of making generic code a
library that can be used or overridden by device-specific code as
the details of specific devices dictate.
- Drivers that do not need to pin userspace memory regions do not
need to take the performance hit of calling ib_mem_get(). For
example, although I have not tried to implement it in this patch,
the ipath driver should be able to avoid pinning memory and just
use copy_{to,from}_user() to access userspace memory regions.
- Buffers that need special mapping treatment can be identified by
the low-level driver. For example, it may be possible to solve
some Altix-specific memory ordering issues with mthca CQs in
userspace by mapping CQ buffers with extra flags.
- Drivers that need to pin and DMA map userspace memory for things
other than memory regions can use ib_umem_get() directly, instead
of hacks using extra parameters to their reg_phys_mr method. For
example, the mlx4 driver that is pending being merged needs to pin
and DMA map QP and CQ buffers, but it does not need to create a
memory key for these buffers. So the cleanest solution is for mlx4
to call ib_umem_get() in the create_qp and create_cq methods.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes it so that simple_fill_super and get_sb_pseudo assign their
root inodes to be number 1. It also fixes up a couple of callers of
simple_fill_super that were passing in files arrays that had an index at
number 1, and adds a warning for any caller that sends in such an array.
It would have been nice to have made it so that it wasn't possible to make
such a collision, but some callers need to be able to control what inode
number their entries get, so I think this is the best that can be done.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Convert to NAPI
IB: Return "maybe missed event" hint from ib_req_notify_cq()
IB: Add CQ comp_vector support
IB/ipath: Fix a race condition when generating ACKs
IB/ipath: Fix two more spin lock problems
IB/fmr_pool: Add prefix to all printks
IB/srp: Set proc_name
IB/srp: Add orig_dgid sysfs attribute to scsi_host
IPoIB/cm: Don't crash if remote side uses one QP for both directions
RDMA/cxgb3: Support for new abort logic
RDMA/cxgb3: Initialize cpu_idx field in cpl_close_listserv_req message
RDMA/cxgb3: Fail qp creation if the requested max_inline is too large
RDMA/cxgb3: Fix TERM codes
IPoIB/cm: Fix error handling in ipoib_cm_dev_open()
IB/ipath: Don't corrupt pending mmap list when unmapped objects are freed
IB/mthca: Work around kernel QP starvation
IB/ipath: Don't put QP in timeout queue if waiting to send
IB/ipath: Don't call spin_lock_irq() from interrupt context
The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a problem where simple ACKs can be sent ahead of RDMA read
responses thus implicitly NAKing the RDMA read.
Signed-off-by: Ralph Campbell <ralph.cambpell@qlogic.com>
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a missing unlock in ipath_rc_rcv_resp() and remove an extra unlock
from ipath_rc_rcv_error().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the pending mmap code so it doesn't corrupt the list of pending
mmaps and crash the machine when pending mmaps are destroyed without
first being mapped. Also, remove an unused variable, and use standard
kernel lists instead of our own homebrewed linked list implementation
to keep the pending mmap list.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes a problem which causes too many RC timeouts and
retransmits.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the problem reported by Bernd Schubert <bs@q-leap.de>
with kernel debug options enabled:
BUG: at kernel/lockdep.c:1860 trace_hardirqs_on()
This was caused by using spin_lock_irq()/spin_unlock_irq() from
interrupt context. Fix all the places that might be called from
interrupts to use spin_lock_irqsave()/spin_unlock_irqrestore().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All RDMA drivers except ehca set class_dev->dev to their dma_device
value (ehca leaves this unset). dma_device is the only value that
makes any sense, so move this assignment to core/sysfs.c. This reduce
the duplicated code in the rest of the drivers and gives ehca a nice
/sys/class/infiniband/ehcaX/device symlink.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The kernel ib_wc structure now uses a QP pointer, but the user space
equivalent uses a QP number instead. This means we can no longer use
a simple structure copy to copy stuff into user space.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't let userspace use the direct-physical-map L_key or R_key.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At some point things changed so that all the affinity bits can be set,
but cpus_full() macro is not true. This caused problems with the unit
selection logic on multi-unit (board) configurations.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the code that shuts down the IB link earlier in the unload
process, to be sure no new packets can arrive while we are unloading.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To prevent random utility reads and writes of the diag interface to the
chip, we first require a handshake of reading from offset 0 and writing
to offset 0 before any other reads or writes can be done through the
diags device. Otherwise chip errors can be triggered.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the chip is no longer usable, LEDs should be turned off so system
can be found easily in the cluster.
Also some minor reorganizing so both chips print hardware error
message at same point and only if there were unrecovered errors
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Re-init of the kernel structures after a chip reset was leaving the
portdata structure for port zero in an inconsistent state, and a
pointer to it either stale (in re-init code) or NULL (in devdata)
Fixing the order of operations on this struct, and the condition for
interrupt access, prevents the crashes.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a chip bug, the PIOAvail register is not always updated to
memory. This patch allows userspace to force an update.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In initialization, if we bailed at chip specific initialization, we
forgot to clean up the irq we had requested.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a bug where multicast packets without a GRH were not
being dropped as per the IB spec.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the module parameter "kpiobufs" is set too high, the calculation to
reset it to a sane value was incorrect.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix RDMA read response length checking for RDMA_READ_RESPONSE_ONLY to
allow a zero length response. RDMA read responses which don't match
the expected length or occur in response to some other operation
should generate a completion queue error (see table 56, ch. 9.9.2.3 in
the IB spec).
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve port-sharing performance by allowing any process to receive
packets from the shared hardware port under a spin lock for mutual
exclusion. Previously, one process was nominated as the master and
that process was responsible for receiving all packets from the shared
hardware port and either consuming them or forwarding them to their
destination. This led to starvation problems for other processes when
the master process was busy in computation phases.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The port sharing feature mixed kernel virtual addresses as well as
physical addresses for the offset used to describe the mmap address to
map the InfiniPath hardware into user space. This had a conflict on
powerpc. The new scheme converts it to a physical address so it
doesn't conflict with chip addresses and yet still fits in 40/44 bits
so it isn't truncated by 32-bit applications calling mmap64().
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a receive work request has been removed from the queue but has not
had a CQ entry generated for it and the QP is modified to the error
state, the completion entry generated is incorrect. This patch fixes
the problem.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code was converted from a &= ~mask to clear_bit, but the bit was left
shifted instead of being used directly, so we were either trashing
memory several pages away, or sometimes taking a kernel page fault on
an invalid page.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some types of packet errors are moderately common with longer IB
cables and large clusters, and are not reported with prints by other
IB HCA drivers. This suppresses those messages unless the new
__IPATH_ERRPKTDBG bit is set in ipath_debug. Reporting of temporarily
disabled frequent error interrupts was also made clearer
We also distinguish between chip errors, and bad packets sent or
received in the wording of the messages.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a number of bugs with updating the PSN for retries of
RC requests.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When switching to the QP error state, the completion queue entries
(error or flush) were not being generated correctly.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_dbg doesn't need the same prefixes that printk does.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds support for multiple RDMA reads and atomics to be sent
before an ACK is required to be seen by the requester.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a post send is done in loopback and there is no receive queue
entry, the sending QP is put on a timeout list for a while so the
receiver has a chance to post a receive buffer. If the another post
send is done, the code incorrectly tried to put the QP on the timeout
list again an corrupted the timeout list. This eventually leads to a
spin lock deadlock NMI due to the timer function looping forever with
the lock held.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A silly programming error causes a CQ entry to not be generated if a
SRQ limit event is generated.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A recent change was made to allocate memory for a port after CPU
affinity is set. That change didn't account for subports and was
trying to allocate memory for the port twice.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The chip documentation on the expected TID vs eager TID parity error
bits was reversed from what was implemented in the RTL, for both
chips. This corrects the definitions.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell