* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits)
sh: Move SH-4 CPU headers down one more level.
sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
sh: Migrate common board headers to mach-common/.
sh: Move the CPU definition headers from asm/ to cpu/.
serial: sh-sci: Add support SCIF of SH7723
video: add sh_mobile_lcdc platform flags
video: remove unused sh_mobile_lcdc platform data
sh: remove consistent alloc cruft
sh: add dynamic crash base address support
sh: reduce Migo-R smc91x overruns
sh: Fix up some merge damage.
Fix debugfs_create_file's error checking method for arch/sh/mm/
Fix debugfs_create_dir's error checking method for arch/sh/kernel/
sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board
sh: Use sh7720 GPIO on magicpanelr2 board
sh: Add sh7720 pinmux code
sh: Use sh7203 GPIO on rsk7203 board
sh: Add sh7203 pinmux code
sh: Use sh7723 GPIO on AP325RXA board
sh: Add sh7723 pinmux code
...
o elfcorehdr_addr is used by not only the code under CONFIG_PROC_VMCORE
but also by the code which is not inside CONFIG_PROC_VMCORE. For
example, is_kdump_kernel() is used by powerpc code to determine if
kernel is booting after a panic then use previous kernel's TCE table.
So even if CONFIG_PROC_VMCORE is not set in second kernel, one should be
able to correctly determine that we are booting after a panic and setup
calgary iommu accordingly.
o So remove the assumption that elfcorehdr_addr is under
CONFIG_PROC_VMCORE.
o Move definition of elfcorehdr_addr to arch dependent crash files.
(Unfortunately crash dump does not have an arch independent file
otherwise that would have been the best place).
o kexec.c is not the right place as one can Have CRASH_DUMP enabled in
second kernel without KEXEC being enabled.
o I don't see sh setup code parsing the command line for
elfcorehdr_addr. I am wondering how does vmcore interface work on sh.
Anyway, I am atleast defining elfcoredhr_addr so that compilation is not
broken on sh.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pinmux management is tied in to this code, while it is presently only
used by platforms that select GENERIC_GPIO. The asm/gpio.h definitions
are not referenced when GENERIC_GPIO is disabled, resulting in a build
failure for all of the platforms that don't select it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove left overs from the generic declared coherent rework.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve Migo-R ethernet performance by reducing smc91x overruns.
This is done by enabling SMC91X_NOWAIT and optimizing CS4 setup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
debugfs_create_file() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Renesas AP325RXA board has Epson RX-8564LC of RTC.
This patch supports RTC of this board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch hooks up the magicpanelr2 board with the sh7720 pinmux code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7720 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make the rsk7203 board use the newly added sh7203 pinmux code.
Only a single LED plus the serial console pins for now.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7203 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on AP325RXA and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
While at it 2 LEDs and one switch are added and exported to user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7723 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on Migo-R and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
Fix whitespace damage while at it and add 2 LEDs and export them to
user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7722 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds gpio code together with the pinmux table parser.
In the future we should optimize this and switch back to gpiolib.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This tidies up a lot of the PIO/MMIO split. No in-tree platforms were
making use of the MMIO overloading through the machvec (nor have any of
them been in some time), so we just kill all of that off. The ISA I/O
routine wrapping remains unaffected, which remains the only special
casing outside of the iomap API that boards need to think about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a workaround for users of sh_mobile_lcdcfb that don't
define HAVE_CLK and have otherwise sane clock initialization.
At the same time, move the sh_mobile_lcdc.h header to include/video/.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The INTC code will be re-used across different architectures, so move
this out to drivers/sh/ and include/linux/sh_intc.h respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were doing largely bogus things and using the wrong typing for
the address. Bring these in line with the ARM definitions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
AP320 and AP325RXA has CPLD data in NOR Flash.
If this area erased, this board can not boot.
This patch create CPLD data area and set writeable mask bit.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for ftrace to SH. This only includes CONFIG_FTRACE,
and does not handle dynamic ftrace presently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a few trace points across events that are deemed
interesting. This implements a number of trace points:
- The page fault handler / TLB miss
- IPC calls
- Kernel thread creation
The original LTTng patch had the slow-path instrumented, which
fails to account for the vast majority of events. In general
placing this in the fast-path is not a huge performance hit, as
we don't take page faults for kernel addresses.
The other bits of interest are some of the other trap handlers, as
well as the syscall entry/exit (which is better off being handled
through the tracehook API). Most of the other trap handlers are corner
cases where alternate means of notification exist, so there is little
value in placing extra trace points in these locations.
Based on top of the points provided both by the LTTng instrumentation
patch as well as the patch shipping in the ST-Linux tree, albeit in a
stripped down form.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are other places where we want to have access to the trap/exception
number, so move out the lookup_exception_vector() helper. While we're at
it, refactor it slightly to return the vector instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is 256K instead of 1M.
[ Converted to use asm/sizes.h. -- PFM ]
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the powerpc commit f6a616800e
'[POWERPC] Fix kernel stack allocation alignment'.
SH has traditionally forced the thread order to be relative to the page
size, so there were never any situations where the same bug was
triggered by slub. Regardless, the usage of > 8kB stacks for the larger
page sizes is overkill, so we switch to using slab allocations there,
as per the powerpc change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This combination triggers a divide by zero in kernel/fork.c when
calculating the initial max_threads value:
max_threads = mempages / (8 * THREAD_SIZE / PAGE_SIZE);
Simply disable 4K stacks on 64kB PAGE_SIZE to work around this,
as it's not a terribly useful combination to begin with.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds