Replace __s390x__ with CONFIG_64BIT in all places that are not exported
to userspace or guarded with #ifdef __KERNEL__.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Whenever the cpu loads an enabled wait PSW it will appear as idle to the
underlying host system. The code in default_idle calls vtime_stop_cpu
which does the necessary voodoo to get the cpu time accounting right.
The udelay code just loads an enabled wait PSW. To correct this rework
the vtime_stop_cpu/vtime_start_cpu logic and move the difficult parts
to entry[64].S, vtime_stop_cpu can now be called from anywhere and
vtime_start_cpu is gone. The correction of the cpu time during wakeup
from an enabled wait PSW is done with a critical section in entry[64].S.
As vtime_start_cpu is gone, s390_idle_check can be removed as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define struct pcpu and merge some of the NR_CPUS arrays into it, including
__cpu_logical_map, current_set and smp_cpu_state. Split smp related
functions to those operating on physical cpus and the functions operating
on a logical cpu number. Make the functions for physical cpus use a
pointer to a struct pcpu. This hides the knowledge about cpu addresses in
smp.c, entry[64].S and swsusp_asm64.S, thus remove the sigp.h header.
The PSW restart mechanism is used to start secondary cpus, calling a
function on an online cpu, calling a function on the ipl cpu, and for
the nmi signal. Replace the different assembler functions with a
single function restart_int_handler. The new entry point calls a function
whose pointer is stored in the lowcore of the target cpu and it can wait
for the source cpu to stop. This covers all existing use cases.
Overall the code is now simpler and there are ~380 lines less code.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split out addressing mode bits from PSW_BASE_BITS, rename PSW_BASE_BITS
to PSW_MASK_BASE, get rid of psw_user32_bits, remove unused function
enabled_wait(), introduce PSW_MASK_USER, and drop PSW_MASK_MERGE macros.
Change psw_kernel_bits / psw_user_bits to contain only the bits that
are always set in the respective mode.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The alignment is missing for various global symbols in s390 assembly code.
With a recent gcc and an instruction like stgrl this can lead to a
specification exception if the instruction uses such a mis-aligned address.
Specify the alignment explicitely and while add it define __ALIGN for s390
and use the ENTRY define to save some lines of code.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Implement ndelay() on s390 as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change futex_atomic_op_inuser and futex_atomic_cmpxchg_inatomic
prototypes to use u32 types for the futex as this is the data type the
futex core code uses all over the place.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311025058.GD26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cmpxchg_futex_value_locked API was funny in that it returned either
the original, user-exposed futex value OR an error code such as -EFAULT.
This was confusing at best, and could be a source of livelocks in places
that retry the cmpxchg_futex_value_locked after trying to fix the issue
by running fault_in_user_writeable().
This change makes the cmpxchg_futex_value_locked API more similar to the
get_futex_value_locked one, returning an error code and updating the
original value through a reference argument.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile]
Acked-by: Tony Luck <tony.luck@intel.com> [ia64]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michal Simek <monstr@monstr.eu> [microblaze]
Acked-by: David Howells <dhowells@redhat.com> [frv]
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311024851.GC26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The uaccess functions copy_in_user_std and clear_user_std fail to
switch back from secondary space mode to primary space mode with sacf
in case of an unresolvable page fault. We need to make sure that the
switch back to primary mode is done in all cases, otherwise the code
following the uaccess inline assembly will crash.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let local_tick_enable/disable() reprogram the clock comparator so the
function names make semantically more sense.
Also that way the functions are more symmetric since normally each
local_tick_enable() call usually would have a subsequent call to
set_clock_comparator() anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On each machine check all registers are revalidated. The save area for
the clock comparator however only contains the upper most seven bytes
of the former contents, if valid.
Therefore the machine check handler uses a store clock instruction to
get the current time and writes that to the clock comparator register
which in turn will generate an immediate timer interrupt.
However within the lowcore the expected time of the next timer
interrupt is stored. If the interrupt happens before that time the
handler won't be called. In turn the clock comparator won't be
reprogrammed and therefore the interrupt condition stays pending which
causes an interrupt loop until the expected time is reached.
On NOHZ machines this can result in unresponsive machines since the
time of the next expected interrupted can be a couple of days in the
future.
To fix this just revalidate the clock comparator register with the
expected value.
In addition the special handling for udelay must be changed as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If there is no in kernel image caller modules will suffer:
ERROR: "copy_from_user_overflow" [net/core/pktgen.ko] undefined!
ERROR: "copy_from_user_overflow" [net/can/can-raw.ko] undefined!
ERROR: "copy_from_user_overflow" [fs/cifs/cifs.ko] undefined!
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces a new function that checks the running status
of a cpu in a hypervisor. This status is not virtualized, so the check
is only correct if running in an LPAR. On acquiring a spinlock, if the
cpu holding the lock is scheduled by the hypervisor, we do a busy wait
on the lock. If it is not scheduled, we yield over to that cpu.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Same as on x86 and sparc, besides the fact that enabling the option
will just emit compile time warnings instead of errors.
Keeps allyesconfig kernels compiling.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Finally move it to the place where it belongs to and make get rid of
it for !CONFIG_SMP.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Name space cleanup for rwlock functions. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
Not strictly necessary for -rt as -rt does not have non sleeping
rwlocks, but it's odd to not have a consistent naming convention.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
Name space cleanup. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
The raw_spin* namespace was taken by lockdep for the architecture
specific implementations. raw_spin_* would be the ideal name space for
the spinlocks which are not converted to sleeping locks in preempt-rt.
Linus suggested to convert the raw_ to arch_ locks and cleanup the
name space instead of using an artifical name like core_spin,
atomic_spin or whatever
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: linux-arch@vger.kernel.org
The pagetable walk usercopy functions have used a modified copy of the
do_exception() function for fault handling. This lead to inconsistencies
with recent changes to do_exception(), e.g. performance counters. This
patch changes the pagetable walk usercopy code to call do_exception()
directly, eliminating the redundancy. A new parameter is added to
do_exception() to specify the fault address.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce user_mode to replace the two variables switch_amode and
s390_noexec. There are three valid combinations of the old values:
1) switch_amode == 0 && s390_noexec == 0
2) switch_amode == 1 && s390_noexec == 0
3) switch_amode == 1 && s390_noexec == 1
They get replaced by
1) user_mode == HOME_SPACE_MODE
2) user_mode == PRIMARY_SPACE_MODE
3) user_mode == SECONDARY_SPACE_MODE
The new kernel parameter user_mode=[primary,secondary,home] lets
you choose the address space mode the user space processes should
use. In addition the CONFIG_S390_SWITCH_AMODE config option
is removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds an EX_TABLE entry to mvc{p|s|os} usercopy functions that
may be called with KERNEL_DS. In combination with collaborative memory
management, kernel pages marked as unused may trigger an adressing exception
in the usercopy functions. This fixes an unhandled addressing exception bug
where strncpy_from_user() is used with len > strnlen and KERNEL_DS, crossing
a page boundary to an unused page.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use an own implementation instead of the common code udelay loop.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When udelay() gets called with a delay that would expire before the
next clock event it reprograms the clock comparator.
When the interrupt happens the clock comparator won't be resetted
therefore the interrupt condition doesn't get cleared.
The result is an endless timer interrupt loop until the next clock
event would expire (stored in lowcore).
So udelay() usually would wait much longer for small delays than it
should.
Fix this by disabling the local tick which makes sure that the clock
comparator will be resetted when a timer interrupt happens.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide __ucmpdi2() helper function on 31 bit so we don't run
again and again in compile errors like this one:
kernel/built-in.o: In function `T.689':
perf_counter.c:(.text+0x56c86): undefined reference to `__ucmpdi2'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use builtin variants if gcc 4 or newer is used to compile the kernel.
Generates better code than the asm variants.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move all EXPORT_SYMBOLs to their corresponding definitions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pfn_valid() actually checks for a valid struct page and not for a
valid pfn. Using xip mappings w/o struct pages, this will result in
-EFAULT returned by the (page table walk) user copy functions,
even though there is valid memory. Those user copy functions don't
need a struct page, so this patch just removes the pfn_valid() check.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The implementation of __div64_31 for G5 machines is broken. The comments
in __div64_31 are correct, only the code does not do what the comments
say. The part "If the remainder has overflown subtract base and increase
the quotient" is only partially realized, the base is subtracted correctly
but the quotient is only increased if the dividend had the last bit set.
Using the correct instruction fixes the problem.
Cc: stable@kernel.org
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move cio's private simple udelay function to lib/delay.c and turn it
into something much more readable. So we have all implementations
at one place.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This fixes a regression that came with 934b2857cc
("[S390] nohz/sclp: disable timer on synchronous waits.").
If udelay() gets called from a disabled context it sets the clock comparator
to a value where it expects the next interrupt. When the interrupt happens
the clock comparator gets not reset and therefore the interrupt condition
doesn't get cleared. The result is an endless timer interrupt loop.
In addition this patch fixes also the following:
rcutorture reveals that our __udelay implementation is still buggy,
since it might schedule tasklets, but prevents their execution:
NOHZ: local_softirq_pending 42
NOHZ: local_softirq_pending 02
NOHZ: local_softirq_pending 142
NOHZ: local_softirq_pending 02
To fix this we make sure that only the clock comparator interrupt
is enabled when the enabled wait psw is loaded.
Also no code gets called anymore which might schedule tasklets.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sclp_sync_wait wait synchronously for an sclp interrupt and disables
timer interrupts. However on the irq enter paths there is an extra
check if a timer interrupt would be due and calls the timer callback.
This would schedule softirqs in the wrong context.
So introduce local_tick_enable/disable which prevents this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch/s390/lib/uaccess_mvcos.c:166:
warning: 'strnlen_user_mvcos' defined but not used
arch/s390/lib/uaccess_mvcos.c:186:
warning: 'strncpy_from_user_mvcos' defined but not used
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current uaccess page table walk code assumes at a few places that
any access is a user space access. This is not correct if somebody
has issued a set_fs(KERNEL_DS) in advance.
Add code which checks which address space we are in and with this make
sure we access the correct address space. This way we get also rid of
the dirty
if (!currrent-mm)
return -EFAULT;
hack in futex_atomic_cmpxchg_pt.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This way we get rid of s390's NO_IDLE_HZ and use the generic dynticks
variant instead. In addition we get high resolution timers for free.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
a0c1e9073e "futex: runtime enable pi and
robust functionality" introduces a test wether futex in atomic stuff
works or not.
It does that by writing to address 0 of the kernel address space. This
will crash on older machines where addressing mode switching is enabled
but where the mvcos instruction is not available. Page table walking is
done by hand and therefore the code tries to access current->mm which
is NULL.
Therefore add an extra check, so we survive the early test.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add missing exception table entry so that the kernel can handle
proctection exceptions as well on the cs instruction. Currently only
specification exceptions are handled correctly.
The missing entry allows user space to crash the kernel.
Cc: stable <stable@kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In s390's spin_lock_irqsave, interrupts remain disabled while
spinning. In other architectures like x86 and powerpc, interrupts are
re-enabled while spinning if IRQ is not masked before spin_lock_irqsave
is called.
The following patch re-enables interrupts through local_irq_restore
while spinning for a lock acquisition.
This can improve system response.
[heiko.carstens@de.ibm.com: removed saving of pc]
Signed-off-by: Hisashi Hifumi <hifumi.hisashi@oss.ntt.co.jp>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Used to contain the address of the holder of the lock. But since the
spinlock code is not inlined anymore all locks contain the same address
anyway. And since in addtition nobody complained about that for ages
its obviously unused. So remove it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
is_init() is an ambiguous name for the pid==1 check. Split it into
is_global_init() and is_container_init().
A cgroup init has it's tsk->pid == 1.
A global init also has it's tsk->pid == 1 and it's active pid namespace
is the init_pid_ns. But rather than check the active pid namespace,
compare the task structure with 'init_pid_ns.child_reaper', which is
initialized during boot to the /sbin/init process and never changes.
Changelog:
2.6.22-rc4-mm2-pidns1:
- Use 'init_pid_ns.child_reaper' to determine if a given task is the
global init (/sbin/init) process. This would improve performance
and remove dependence on the task_pid().
2.6.21-mm2-pidns2:
- [Sukadev Bhattiprolu] Changed is_container_init() calls in {powerpc,
ppc,avr32}/traps.c for the _exception() call to is_global_init().
This way, we kill only the cgroup if the cgroup's init has a
bug rather than force a kernel panic.
[akpm@linux-foundation.org: fix comment]
[sukadev@us.ibm.com: Use is_global_init() in arch/m32r/mm/fault.c]
[bunk@stusta.de: kernel/pid.c: remove unused exports]
[sukadev@us.ibm.com: Fix capability.c to work with threaded init]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Herbert Poetzel <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bogomips calculation triggered via reading from /proc/cpuinfo
can return incorrect values if the qrnnd assembly is called with a
pointer in %r2 with any of the upper 32 bits set.
Fix this by using 64 bit division / remainder operation provided by
gcc instead of calling the assembly.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow s390 to properly override the generic
__div64_32() implementation by:
1) Using obj-y for div64.o in s390's makefile instead
of lib-y
2) Adding the weak attribute to the generic implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens