This reverts commit 906b40b246 ("dmaengine: stm32-mdma: Add a check on
read_u32_array")
As stated by bindings "st,ahb-addr-masks" is optional.
The statement inserted by this commit makes this property
mandatory and prevents MDMA to be probed in case property not present.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers
multi-block support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
-----BEGIN PGP SIGNATURE-----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=Ykvn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
Patch series "Replace all open encodings for NUMA_NO_NODE", v3.
All these places for replacement were found by running the following
grep patterns on the entire kernel code. Please let me know if this
might have missed some instances. This might also have replaced some
false positives. I will appreciate suggestions, inputs and review.
1. git grep "nid == -1"
2. git grep "node == -1"
3. git grep "nid = -1"
4. git grep "node = -1"
This patch (of 2):
At present there are multiple places where invalid node number is
encoded as -1. Even though implicitly understood it is always better to
have macros in there. Replace these open encodings for an invalid node
number with the global macro NUMA_NO_NODE. This helps remove NUMA
related assumptions like 'invalid node' from various places redirecting
them to a common definition.
Link: http://lkml.kernel.org/r/1545127933-10711-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [ixgbe]
Acked-by: Jens Axboe <axboe@kernel.dk> [mtip32xx]
Acked-by: Vinod Koul <vkoul@kernel.org> [dmaengine.c]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Doug Ledford <dledford@redhat.com> [drivers/infiniband]
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without the copy being aligned sdma1 fails ~10% of the time
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On i.mx8mq, there are two sdma instances, and the common dma framework
will get a channel dynamically from any available sdma instance whether
it's the first sdma device or the second sdma device. Some IPs like
SAI only work with sdma2 not sdma1. To make sure the sdma channel is from
the correct sdma device, use the node pointer to match.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On i.mx8 mscale B0 chip, AHB/SDMA clock ratio 2:1 can't be supportted,
since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach
to 500Mhz, so use 1:1 instead.
Based on NXP commit MLK-16841-1 by Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch starts to take advantage of the `dmatest_data` struct by moving
the common allocation & free-ing bits into functions.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is just a cosmetic change, since this variable gets used quite a bit
inside the dmatest_func() routine.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This change wraps the data for the source & destination buffers into a
`struct dmatest_data`. The rename patterns are:
* src_cnt -> src->cnt
* dst_cnt -> dst->cnt
* src_off -> src->off
* dst_off -> dst->off
* thread->srcs -> src->aligned
* thread->usrcs -> src->raw
* thread->dsts -> dst->aligned
* thread->udsts -> dst->raw
The intent is to make a function that moves duplicate parts of the code
into common alloc & free functions, which will unclutter the
`dmatest_func()` function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
IOATDMA 3.4 supports PCIe LTR mechanism. The registers are non-standard
PCIe LTR support. This needs to be setup in order to not suffer performance
impact and provide proper power management. The channel is set to active
when it is allocated, and to passive when it's freed.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adding support for new feature on ioatdma 3.4 hardware that provides
descriptor pre-fetching in order to reduce small DMA latencies.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add Snowridge Xeon-D ioatdma PCI device id. Also applies for Icelake
SP Xeon. This introduces ioatdma v3.4 platform. Also bumping driver version
to 5.0 since we are adding additional code for 3.4 support.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We will describe the slave id in DMA cell specifier instead of DMA channel
id, thus we should save the slave id from DMA engine translation function,
and remove the channel id validation.
Meanwhile we do not need set default slave id in sprd_dma_alloc_chan_resources(),
remove it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using dma_dev->dev for mappings before it's assigned with the correct
device is unlikely to work as expected, and with future dma-direct
changes, passing a NULL device may end up crashing entirely. I don't
know enough about this hardware or the mv_xor_prep_dma_interrupt()
operation to implement the appropriate error-handling logic that would
have revealed those dma_map_single() calls failing on arm64 for as long
as the driver has been enabled there, but moving the assignment earlier
will at least make the current code operate as intended.
Fixes: 22843545b2 ("dma: mv_xor: Add support for DMA_INTERRUPT")
Reported-by: John David Anglin <dave.anglin@bell.net>
Tested-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dmaengine fixes for v5.0-rc6
- Fix in at_xdmac fr wrongful channel state
- Fix for imx driver for wrong callback invocation
- Fix to bcm driver for interrupt race & transaction abort.
- Fix in dmatest to abort in mapping error
-----BEGIN PGP SIGNATURE-----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=NTGY
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- Fix in at_xdmac fr wrongful channel state
- Fix for imx driver for wrong callback invocation
- Fix to bcm driver for interrupt race & transaction abort.
- Fix in dmatest to abort in mapping error
* tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dmatest: Abort test in case of mapping error
dmaengine: bcm2835: Fix abort of transactions
dmaengine: bcm2835: Fix interrupt race on RT
dmaengine: imx-dma: fix wrong callback invoke
dmaengine: at_xdmac: Fix wrongfull report of a channel as in use
Add dma-channel-mask as a property for k3dma, it defines
available dma channels which a non-secure mode driver can use.
One sample usage of this is in Hi3660 SoC. DMA channel 0 is
reserved to lpm3, which is a coprocessor for power management. So
as a result, any request in kernel (which runs on main processor
and in non-secure mode) should start from at least channel 1.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Tanglei Han <hantanglei@huawei.com>
Cc: Zhuangluan Su <suzhuangluan@hisilicon.com>
Cc: Ryan Grachek <ryan@edited.us>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Li Yu <liyu65@hisilicon.com>
[jstultz: Reworked to use a channel mask]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Axi_config controls whether DMA resources can be accessed in non-secure
mode, such as linux kernel. The register should be set by the bootloader
stage and depends on the device.
Thus, this patch removes axi_config from k3dma driver.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Tanglei Han <hantanglei@huawei.com>
Cc: Zhuangluan Su <suzhuangluan@hisilicon.com>
Cc: Ryan Grachek <ryan@edited.us>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: dmaengine@vger.kernel.org
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Li Yu <liyu65@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
[jstultz: Minor tweaks to commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On the hi3660 hardware there are two (at least) DMA controllers,
the DMA-P (Peripheral DMA) and the DMA-A (Audio DMA). The
two blocks are similar, but have some slight differences. This
resulted in the vendor implementing two separate drivers, which
after review, they have been able to condense and re-use the
existing k3dma driver.
Thus, this patch adds support for the new "hisi-pcm-asp-dma-1.0"
compatible string in the binding.
One difference with the DMA-A controller, is that it does not
need to initialize a clock. So we skip this by adding and using
soc data flags.
After above this driver will support both k3 and hisi_asp dma
hardware.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Zhuangluan Su <suzhuangluan@hisilicon.com>
Cc: Ryan Grachek <ryan@edited.us>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: dmaengine@vger.kernel.org
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Youlin Wang <wwx575822@notesmail.huawei.com>
Signed-off-by: Tanglei Han <hantanglei@huawei.com>
[jstultz: Reworked to use of_match_data, commit msg improvements]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Otherwise 64-bit PPC builds fail with undefined references
to these accessors.
Cc: Peng Ma <peng.ma@nxp.com>
Cc: Wen He <wen.he_1@nxp.com>
Fixes: 68997fff94afa (" dmaengine: fsldma: Adding macro FSL_DMA_IN/OUT implement for ARM platform")
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove an outdated comment claiming the driver only supports cyclic
transactions. The driver has been supporting other transaction types
for more than two years.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The BCM2835 DMA driver deletes a channel from a list upon termination
without having added it to a list first. Moreover that operation is
protected by a spinlock which isn't taken anywhere else. These appear
to be remnants of an older version of the driver which accidentally
got mainlined. Remove the dead code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Per section 4.2.1.1 of the BCM2835 ARM Peripherals spec, control blocks
"must start at a 256 bit aligned address":
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
This rule is currently satisfied only by accident because struct
bcm2835_dma_cb has a size of 256 bit and the DMA pool API happens to
allocate blocks consecutively. It seems safer to be explicit and tell
the DMA pool allocator about the required alignment.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
bcm2835_dma_abort() returns an int but bcm2835_dma_terminate_all() (its
sole caller) does not evaluate the return value. Change the return type
to void.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are multiple issues with bcm2835_dma_abort() (which is called on
termination of a transaction):
* The algorithm to abort the transaction first pauses the channel by
clearing the ACTIVE flag in the CS register, then waits for the PAUSED
flag to clear. Page 49 of the spec documents the latter as follows:
"Indicates if the DMA is currently paused and not transferring data.
This will occur if the active bit has been cleared [...]"
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
So the function is entering an infinite loop because it is waiting for
PAUSED to clear which is always set due to the function having cleared
the ACTIVE flag. The only thing that's saving it from itself is the
upper bound of 10000 loop iterations.
The code comment says that the intention is to "wait for any current
AXI transfer to complete", so the author probably wanted to check the
WAITING_FOR_OUTSTANDING_WRITES flag instead. Amend the function
accordingly.
* The CS register is only read at the beginning of the function. It
needs to be read again after pausing the channel and before checking
for outstanding writes, otherwise writes which were issued between
the register read at the beginning of the function and pausing the
channel may not be waited for.
* The function seeks to abort the transfer by writing 0 to the NEXTCONBK
register and setting the ABORT and ACTIVE flags. Thereby, the 0 in
NEXTCONBK is sought to be loaded into the CONBLK_AD register. However
experimentation has shown this approach to not work: The CONBLK_AD
register remains the same as before and the CS register contains
0x00000030 (PAUSED | DREQ_STOPS_DMA). In other words, the control
block is not aborted but merely paused and it will be resumed once the
next DMA transaction is started. That is absolutely not the desired
behavior.
A simpler approach is to set the channel's RESET flag instead. This
reliably zeroes the NEXTCONBK as well as the CS register. It requires
less code and only a single MMIO write. This is also what popular
user space DMA drivers do, e.g.:
https://github.com/metachris/RPIO/blob/master/source/c_pwm/pwm.c
Note that the spec is contradictory whether the NEXTCONBK register
is writeable at all. On the one hand, page 41 claims:
"The value loaded into the NEXTCONBK register can be overwritten so
that the linked list of Control Block data structures can be
dynamically altered. However it is only safe to do this when the DMA
is paused."
On the other hand, page 40 specifies:
"Only three registers in each channel's register set are directly
writeable (CS, CONBLK_AD and DEBUG). The other registers (TI,
SOURCE_AD, DEST_AD, TXFR_LEN, STRIDE & NEXTCONBK), are automatically
loaded from a Control Block data structure held in external memory."
Fixes: 96286b5766 ("dmaengine: Add support for BCM2835")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.14+
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Cc: Clive Messer <clive.m.messer@gmail.com>
Cc: Matthias Reichl <hias@horus.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If IRQ handlers are threaded (either because CONFIG_PREEMPT_RT_BASE is
enabled or "threadirqs" was passed on the command line) and if system
load is sufficiently high that wakeup latency of IRQ threads degrades,
SPI DMA transactions on the BCM2835 occasionally break like this:
ks8851 spi0.0: SPI transfer timed out
bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
ks8851 spi0.0 eth2: ks8851_rdfifo: spi_sync() failed
The root cause is an assumption made by the DMA driver which is
documented in a code comment in bcm2835_dma_terminate_all():
/*
* Stop DMA activity: we assume the callback will not be called
* after bcm_dma_abort() returns (even if it does, it will see
* c->desc is NULL and exit.)
*/
That assumption falls apart if the IRQ handler bcm2835_dma_callback() is
threaded: A client may terminate a descriptor and issue a new one
before the IRQ handler had a chance to run. In fact the IRQ handler may
miss an *arbitrary* number of descriptors. The result is the following
race condition:
1. A descriptor finishes, its interrupt is deferred to the IRQ thread.
2. A client calls dma_terminate_async() which sets channel->desc = NULL.
3. The client issues a new descriptor. Because channel->desc is NULL,
bcm2835_dma_issue_pending() immediately starts the descriptor.
4. Finally the IRQ thread runs and writes BCM2835_DMA_INT to the CS
register to acknowledge the interrupt. This clears the ACTIVE flag,
so the newly issued descriptor is paused in the middle of the
transaction. Because channel->desc is not NULL, the IRQ thread
finalizes the descriptor and tries to start the next one.
I see two possible solutions: The first is to call synchronize_irq()
in bcm2835_dma_issue_pending() to wait until the IRQ thread has
finished before issuing a new descriptor. The downside of this approach
is unnecessary latency if clients desire rapidly terminating and
re-issuing descriptors and don't have any use for an IRQ callback.
(The SPI TX DMA channel is a case in point.)
A better alternative is to make the IRQ thread recognize that it has
missed descriptors and avoid finalizing the newly issued descriptor.
So first of all, set the ACTIVE flag when acknowledging the interrupt.
This keeps a newly issued descriptor running.
If the descriptor was finished, the channel remains idle despite the
ACTIVE flag being set. However the ACTIVE flag can then no longer be
used to check whether the channel is idle, so instead check whether
the register containing the current control block address is zero
and finalize the current descriptor only if so.
That way, there is no impact on latency and throughput if the client
doesn't care for the interrupt: Only minimal additional overhead is
introduced for non-cyclic descriptors as one further MMIO read is
necessary per interrupt to check for idleness of the channel. Cyclic
descriptors are sped up slightly by removing one MMIO write per
interrupt.
Fixes: 96286b5766 ("dmaengine: Add support for BCM2835")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.14+
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Cc: Clive Messer <clive.m.messer@gmail.com>
Cc: Matthias Reichl <hias@horus.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Once the "ld_queue" list is not empty, next descriptor will migrate
into "ld_active" list. The "desc" variable will be overwritten
during that transition. And later the dmaengine_desc_get_callback_invoke()
will use it as an argument. As result we invoke wrong callback.
That behaviour was in place since:
commit fcaaba6c71 ("dmaengine: imx-dma: fix callback path in tasklet").
But after commit 4cd13c21b2 ("softirq: Let ksoftirqd do its job")
things got worse, since possible delay between tasklet_schedule()
from DMA irq handler and actual tasklet function execution got bigger.
And that gave more time for new DMA request to be submitted and
to be put into "ld_queue" list.
It has been noticed that DMA issue is causing problems for "mxc-mmc"
driver. While stressing the system with heavy network traffic and
writing/reading to/from sd card simultaneously the timeout may happen:
10013000.sdhci: mxcmci_watchdog: read time out (status = 0x30004900)
That often lead to file system corruption.
Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cc: stable@vger.kernel.org
This mapping needs to be created in order for slave dma transfers
to work on systems with SMMU. The implementation mostly mimics the
one in pl330 dma driver, authored by Robin Murphy.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
atchan->status variable is used to store two different information:
- pass channel interrupts status from interrupt handler to tasklet;
- channel information like whether it is cyclic or paused;
This causes a bug when device_terminate_all() is called,
(AT_XDMAC_CHAN_IS_CYCLIC cleared on atchan->status) and then a late End
of Block interrupt arrives (AT_XDMAC_CIS_BIS), which sets bit 0 of
atchan->status. Bit 0 is also used for AT_XDMAC_CHAN_IS_CYCLIC, so when
a new descriptor for a cyclic transfer is created, the driver reports
the channel as in use:
if (test_and_set_bit(AT_XDMAC_CHAN_IS_CYCLIC, &atchan->status)) {
dev_err(chan2dev(chan), "channel currently used\n");
return NULL;
}
This patch fixes the bug by adding a different struct member to keep
the interrupts status separated from the channel status bits.
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This commit fixes the issue that USB-DMAC hangs silently after system
resumes on R-Car Gen3 hence renesas_usbhs will not work correctly
when using USB-DMAC for bulk transfer e.g. ethernet or serial
gadgets.
The issue can be reproduced by these steps:
1. modprobe g_serial
2. Suspend and resume system.
3. connect a usb cable to host side
4. Transfer data from Host to Target
5. cat /dev/ttyGS0 (Target side)
6. echo "test" > /dev/ttyACM0 (Host side)
The 'cat' will not result anything. However, system still can work
normally.
Currently, USB-DMAC driver does not have system sleep callbacks hence
this driver relies on the PM core to force runtime suspend/resume to
suspend and reinitialize USB-DMAC during system resume. After
the commit 17218e0092 ("PM / genpd: Stop/start devices without
pm_runtime_force_suspend/resume()"), PM core will not force
runtime suspend/resume anymore so this issue happens.
To solve this, make system suspend resume explicit by using
pm_runtime_force_{suspend,resume}() as the system sleep callbacks.
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() is used to make sure USB-DMAC
suspended after and initialized before renesas_usbhs."
Signed-off-by: Phuong Nguyen <phuong.nguyen.xw@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: <stable@vger.kernel.org> # v4.16+
[shimoda: revise the commit log and add Cc tag]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pass ->dev to dma_alloc_coherent() API. We need this
because dma_alloc_coherent() makes use of dev parameter
and receiving NULL will result in a crash.
Signed-off-by: Andy Duan <fugang.duan@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The warning got introduced by commit 930507c183 ("arm64: add basic
Kconfig symbols for i.MX8"). Since it got enabled for arm64. The warning
haven't been seen before since size_t was 'unsigned int' when built on
arm32.
../drivers/dma/imx-dma.c: In function ‘imxdma_sg_next’:
../include/linux/kernel.h:846:29: warning: comparison of distinct pointer types lacks a cast
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
^~
../include/linux/kernel.h:860:4: note: in expansion of macro ‘__typecheck’
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~
../include/linux/kernel.h:870:24: note: in expansion of macro ‘__safe_cmp’
__builtin_choose_expr(__safe_cmp(x, y), \
^~~~~~~~~~
../include/linux/kernel.h:879:19: note: in expansion of macro ‘__careful_cmp’
#define min(x, y) __careful_cmp(x, y, <)
^~~~~~~~~~~~~
../drivers/dma/imx-dma.c:288:8: note: in expansion of macro ‘min’
now = min(d->len, sg_dma_len(sg));
^~~
Rework so that we use min_t and pass in the size_t that returns the
minimum of two values, using the specified type.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/dma/xilinx/xilinx_dma.c: In function 'xilinx_vdma_start_transfer':
drivers/dma/xilinx/xilinx_dma.c:1104:33: warning:
variable 'tail_segment' set but not used [-Wunused-but-set-variable]
It not used since commit b8349172b4 ("dmaengine: xilinx_dma: Drop SG support
for VDMA IP")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pierre-Yves MORDRET