The Tegra clock driver contains legacy code which deasserts hardware reset
when peripheral clocks are enabled. This behaviour comes from a pre-CCF
era of the Tegra drivers. This is unacceptable for modern kernel drivers
which use generic CCF and reset-control APIs because it breaks assumptions
of the drivers about clk/reset sequences and about reset-propagation
delays. Hence remove the awkward legacy behaviour from the clk driver.
In particular PMC driver assumes that hardware blocks remains in reset
while power domain is turning on, but the clk driver deasserts the reset
before power clamp is removed, hence breaking the driver's assumption.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add modularization support to the Tegra124 EMC driver, which now can be
compiled as a loadable kernel module.
Note that EMC clock must be registered at clk-init time, otherwise PLLM
will be disabled as unused clock at boot time if EMC driver is compiled
as a module. Hence add a prepare/complete callbacks. similarly to what is
done for the Tegra20/30 EMC drivers.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201228154920.18846-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
CCLK should be re-parented away from PLLX if PLLX's rate is changing.
The PLLP parent is a common safe CPU parent for all Tegra SoCs, thus
CCLK will be re-parented to PLLP before PLLX rate-change begins and then
switched back to PLLX after the rate-change completion. This patch adds
helper functions which perform CCLK re-parenting, these helpers will be
utilized by further patches.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is a need to temporarily re-parent CCLK away from PLLX if PLLX's
rate is about to change. The newly introduced PLL pre/post rate-change
hooks allow to handle such case.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CCLK stands for "CPU Clock", CPU core is running off CCLK. CCLK supports
multiple parents, it has internal clock divider and a clock skipper.
PLLX is the main CCLK parent that provides clock rates above 1GHz and it
has special property such that the CCLK's internal divider is set into
bypass mode when PLLX is selected as a parent for CCLK.
This patch forks generic Super Clock into CCLK implementation which takes
into account all CCLK specifics. The proper CCLK implementation is needed
by the upcoming Tegra20 CPUFreq driver update that will allow to utilize
the generic cpufreq-dt driver by moving intermediate clock selection into
the clock driver.
Note that technically this patch could be squashed into clk-super.c, but
it is cleaner to have a separate source file. Also note that currently all
CCLKLP bits are left in the clk-super.c and only CCLKG is supported by
clk-tegra-super-cclk. It shouldn't be difficult to move the CCLKLP bits,
but CCLKLP is not used by anything in kernel and thus better not to touch
it for now.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock needs to carefully coordinate with the EMC controller
programming to make sure external memory can be properly clocked. Do so
by hooking up the EMC clock with an EMC provider that will specify which
rates are supported by the EMC and provide a callback to use for setting
the clock rate at the EMC.
Based on work by Peter De Schrijver <pdeschrijver@nvidia.com>.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code is only used on Tegra124, so rename it accordingly to make it
more consistent with other file names.
While at it, also get rid of the TEGRA_CLK_EMC Kconfig symbol that's
really just an alias for TEGRA124_EMC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current Tegra clock driver registers PMC clocks clk_out_1, clk_out_2,
clk_out_3 and 32KHz blink output in tegra_pmc_init() which does direct
PMC register access during clk_ops and these PMC register read and write
access will not happen when PMC is in secure mode.
Any direct PMC register access from non-secure world will not go
through.
All the PMC clocks are moved to Tegra PMC driver with PMC as a clock
provider.
This patch removes tegra_pmc_clk_init along with corresponding clk ids
from Tegra clock driver.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All the CAR controller settings are lost on suspend when core power goes
off. This implement saving and restoring context for all PLLs and clocks
during system suspend and resume to have the clocks back to same state
for normal operation.
Clock driver suspend and resume are registered as syscore_ops as clocks
restore need to happen before the other drivers resume to have all their
clocks back to the same state as before suspend.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move CLK_OUT_ENB and RST_DEVICES registers to clk.h to share these with
Tegra clock driver.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch has a fix to enable PLLP branches to CPU before changing
the CPU cluster clock source to PLLP for Gen5 Super clock and
disables PLLP branches to CPU when not in use.
During system suspend entry and exit, CPU source will be switched
to PLLP and this needs PLLP branches to be enabled to CPU prior to
the switch.
On system resume, warmboot code enables PLLP branches to CPU and
powers up the CPU with PLLP clock source.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support for saving OSC clock frequency and the
drive-strength during OSC clock init and creates an API to restore
OSC control register value from the saved context.
This API is invoked by Tegra210 clock driver during system resume
to restore the OSC clock settings.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A proper External Memory Controller clock rounding and parent selection
functionality is required by the EMC drivers, it is not available using
the generic clock implementation because only the Memory Controller driver
is aware of what clock rates are actually available for a particular
device. EMC drivers will have to register a Tegra-specific CLK-API
callback which will perform rounding of a requested rate. EMC clock users
won't be able to request EMC clock by getting -EPROBE_DEFER until EMC
driver is probed and the callback is set up.
The functionality is somewhat similar to the clk-emc.c which serves
Tegra124+ SoCs. The later HW generations support more parent clock sources
and the HW configuration / integration with the EMC drivers differs a tad
from the older gens, hence it's not really worth to try to squash
everything into a single source file.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum frequency supported for I2S on Tegra124 and Tegra210 is
24.576MHz (as stated in the Tegra TK1 data sheet for Tegra124 and the
Jetson TX1 module data sheet for Tegra210). However, the maximum I2S
frequency is limited to 24MHz because that is the maximum frequency of
the audio sync clock. Increase the maximum audio sync clock frequency
to 24.576MHz for Tegra124 and Tegra210 in order to support 24.576MHz
for I2S.
Update the tegra_clk_register_sync_source() function so that it does
not set the initial rate for the sync clocks and use the clock init
tables to set the initial rate instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock type to model the sdmmc switch divider clocks which have paths
to source clocks bypassing the divider (Low Jitter paths). These
are handled by selecting the lj path when the divider is 1 (ie the
rate is the parent rate), otherwise the normal path with divider
will be selected. Otherwise this clock behaves as a normal peripheral
clock.
Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Move this to a separate file so it can be used to calculate the sdmmc
clock dividers.
Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the missing linux/delay.h include statement for udelay() used by
fence_udelay() macro.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CDEV1 and CDEV2 clocks are a bit special case, their parent clock is
created by the pinctrl driver. It should be possible for clk user to
request these clocks before pinctrl driver got probed and hence user will
get an orphaned clock. That might be undesirable because user may expect
parent clock to be enabled by the child, so let's return -EPROBE_DEFER
till parent clock appears.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To ensure writes to clock registers have properly propagated through the
clock control logic and state machines, we need to ensure the writes have
been posted in the registers and wait for 1us after that.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is a common pattern that registers individual peripheral clocks
from an initialization table. Add a common implementation to remove the
duplication from various call sites.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 PLLX uses the same sequences than then PLLC instances. So there
is no need to have a special registration function and ops struct for it.
Simplify the code by changing all references to the Tegra210 PLLX
registration function to the Tegra210 PLLC registration function and
avoid duplicate functionality.
Based on work by Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The recent conversion of proper const usage was only partial and didn't
include Tegra20 and Tegra30 support. Fix that up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a super clock type which implements both mux and divider. This is
used for aclk.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
checkpatch now warns for const ** and expects const * const * to be used
instead. This means we have to update the prototypes and function
declarations to handle this change.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When used as part of fractional ndiv calculations, the current range is
not enough because the denominator of the fraction is multiplied with m.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move the UTMI PLL initialization code form clk-tegra<chip>.c files into
clk-pll.c. UTMI PLL was being configured and set in HW control right
after registration. However, when the clock init_table is processed and
child clks of PLLU are enabled, it will call in and enable PLLU as
well, and initiate SW enabling sequence even though PLLU is already in
HW control. This leads to getting UTMIPLL stuck with a SEQ_BUSY status.
Doing the initialization once during pllu_enable means we configure it
properly into HW control.
A side effect of the commonization/localization of the UTMI PLL init
code, is that it corrects some errors that were present for earlier
generations. For instance, in clk-tegra124.c, it used to have:
#define UTMIP_PLL_CFG1_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 6)
when the correct shift to use is present in the new version:
#define UTMIP_PLL_CFG1_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 27)
which matches the Tegra124 TRM register definition.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
[rklein: Merged in some later fixes for potential deadlocks]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding: coding style bike-shedding, remove unused variable]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a new Tegra210 version of the pll_register_pllre function to
allow setting the proper settings for the m and n div fields.
Additionally define PLL_RE_OUT1 on Tegra210.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding@nvidia.com: define PLLRE_OUT1 register offset]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the peripheral clocks on Tegra are derived from one of the top-
level PLLs with a fixed factor. Support these clocks by implementing the
->enable() and ->disable() callbacks using the peripheral clock register
banks and the ->recalc_rate() by dividing the parent rate by the fixed
factor.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The peripheral clock registers are defined in static tables. These
tables never need to be modified at runtime, so they can reside in
read-only memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Super clock divider control and clock source mux of Tegra210 has changed
a little against prior SoCs, this patch adds Gen5 logic to address those
differences.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add some logic for Spread Spectrum control. It is used in conjuncture
with SDM fractional dividers. SSC has to be disabled when we configure
the divider settings.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a callback to the pll_params for custom dynamic ramping
functions which can be specified per PLL.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add logic which (if specified for a pll) can verify that a PLL is set
to the proper default value and if not can set it. This can be
specified per PLL as each will have different default values.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code makes use of the SDM fractional divider if present to
constrain the allowable programming range of the PLL divider register
bitfields to take advantage of higher frequency granularity that can
be induced by the SDM divider.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 SoC's have 2 PLLs for memory usage. Add plumbing to register
and handle PLLMB.
PLLMB is used to allow switching between 2 PLLM's without having to use
and intermediate backup PLL, as we need to lock the PLL before we can
switch to it.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra210 SoC's, the logic to enable several of the plls is different
from previous generations. Therefore, add registration functions specific
to Tegra210 which will handle them appropriately.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If a PLL has a reset_reg specified, properly handle that in the
enable/disable logic paths.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For Tegra210, the logic to calculate out-of-table rates is different
from previous generations. Add callbacks that can be overridden to
allow for different ways of calculating rates. Default to
_cal_rate when not specified.
This patch also includes a new flag which is used to set which method
of fixed_mdiv calculation is used. The new method for calculating the
fixed divider value for M can be more accurate especially when
fractional dividers are in play. This allows for older chipsets to use
the existing logic and new generations to use a newer version which
may work better for them.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds logic for taking SDM_DIN (Sigma Delta Modulator) setting into
the equation to calculate the effective N value for PLL which supports
fractional divider.
The effective N = NDIV + 1/2 + SDM_DIN/2^13, where NDIV is the integer
feedback divider.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
New SoC's may have more than 3 MISC registers, so bump up the array size
and use a #define to be more informative about the value.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Create a wrapper interface to make use of the existing
clk_pll_wait_for_lock. This will be useful for implementations
of callbacks in Tegra SoC specific clock drivers.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
tegra_audio_clk_init was written expecting a single PLL to be
passed in directly. Change this to accept an array which will
allow for supporting multiple plls and specifying specific data
about them, like their parent, which may change over time.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Benson Leung pointed out that the kerneldoc for this structure has
become stale. Update the field descriptions to match the structure
content.
Reported-by: Benson Leung <bleung@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some fields moved from the tegra_clk_pll struct to the tegra_pll_params
struct. Update the struct comments to reflect where the fields really
are.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch allows SoC-specific CAR initialization routines to register
their own reset_assert and reset_deassert callbacks with the common Tegra
CAR code. If defined, the common code will call these callbacks when a
reset control with number >= num_periph_banks * 32 is attempted to be asserted
or deasserted respectively. Numbers greater than or equal to num_periph_banks * 32
are used to avoid clashes with low numbers that are automatically mapped to
standard CAR reset lines.
Each SoC with these special resets should specify the defined reset control
numbers in a device tree header file.
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver is currently only tested on Tegra124 Jetson TK1, but should
work with other Tegra124 boards, provided that correct EMC tables are
provided through the device tree. Older chip models have differing
timing change sequences, so they are not currently supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[treding@nvidia.com: use more consistent function names]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko